IXXAT USB-to-CAN compact, USB-to-CAN embedded, USB-to-CAN professional, USB-to-CAN automative Hardware Manual

Hardware Manual
USB-to-CAN
V2
USB CAN Interface
compact embedded automotive professional
E-Mail: info@ix x at. com
Support
www.ixxat.com
Copyright
ment is only allowed with explicit permission of
rights are reserved.
Registered trademarks
party registered are absolutely subject to the conditions of each valid
protected by trademark law.
Document number: 4.01.0280.20000 Version: 1.0
IXXAT Automation GmbH
Leibnizstr. 15 88250 Weingarten Germany
Tel.: +49 751 56146-0 Fax: +49 751 56146-29 Internet: www.ixxat.com
In case of unsolvable problems with this product or other IXXAT products please contact IXXAT in written form:
Fax: +49 751 56146-29 E-Mail: support@ixxat.de
Further international support contacts can be found on our webpage
Duplication (copying , printi ng, m icrof ilm or other form s) and t he elec tro nic distribution of this docu IXXAT Automation Gm bH. IXXAT Autom ation Gm bH reserves the right to change technical data without pri or anno uncem ent. The gen eral b usines s conditions and the regulations of the license agreement do apply. All
All trademarks mentioned in this document and where applicable third label right and the rights of particular registered proprietor. The absence
of identification of a tradem ark does not automat ically mean that it is not
Content
1 Introduction .................................................................................... 5
2 Installation ...................................................................................... 6
2.1 Software installation ............................................................... 6
2.2 Hardware installation .............................................................. 6
2.2.1 USB-to-CANV2 compact / professional / automotive ................ 6
2.2.2 USB-to-CANV2 embedded ........................................................ 6
3 Connectors and displays .............................................................. 7
3.1 USB connector ........................................................................ 7
3.2 Fieldbus connector ................................................................. 7
3.2.1 USB-to-CANV2 compact ........................................................... 7
3.2.2 USB-to-CANV2 professional ..................................................... 8
3.2.3 USB-to-CANV2 automotive ....................................................... 8
3.3 Displays ................................................................................... 9
3.3.1 USB LED .................................................................................. 9
3.3.2 CAN LED .................................................................................. 9
3.3.3 CAN1 LS LED ........................................................................ 10
3.3.4 LIN LED .................................................................................. 10
4 Notes ............................................................................................. 11
4.1 CAN bus termination ............................................................ 11
4.2 LIN interface .......................................................................... 11
4.3 USB-to-CANV2 embedded cable wire assignment .............. 11
5 Appendix ...................................................................................... 12
5.1 Technical data ....................................................................... 12
5.2 Support .................................................................................. 13
5.3 Returning hardware .............................................................. 13
5.4 FCC Compliance ................................................................... 13
5.5 Disposing of old equipment ................................................. 13
5.6 Information on EMC .............................................................. 14
5.7 EC Declaration of Conformi ty .............................................. 14
Copyright IXXAT Automation GmbH
3
USB-to-CANV2 Manual, V1.0
Introduction

1 Introduction

By purchasing the IXXAT USB-to-CANV2 interface, you decided for a high­quality electronic component developed and manufactured according to the latest technological standards.
V2
This manual describes the USB-to-CAN USB-to-CAN terface.
In the further description these interfaces are referred as CAN-interface.
The properties of the CAN interfaces are:
V2
professional as well as the USB-to-CANV2 automotive CAN i n-
USB-to-CANV2 compact / embedded
USB 2.0 Hi-Speed (480MBit/s)
  one CAN-High-Speed channel according ISO11898-2
compact, USB-to-CANV2 embedded,
optional galvanic CAN bus isolation fieldbus connection:
o compact: Sub-D9M or RJ45 o embedded: Sub-D9M
USB-to-CAN
USB 2.0 Hi-Speed (480MBit/s)
V2
professional
two CAN-High-Speed channels according ISO11898-2 galvanic CAN bus isolation (both CAN channels are on the same potential) fieldbus connection: 2 x RJ45 equipped with two cable adapter RJ45 to Sub-D9M
USB-to-CAN
USB 2.0 Hi-Speed (480MBit/s)
V2
automotive
two CAN-High-Speed channels according ISO11898-2, CAN1 can be
switched between high- and low-speed (ISO 11898-3) via software.
one LIN-Interface V1.3, Master/Slave-Mode switchable via software.
Please refer to the instructions in chapter 4.2
galvanic fieldbus isolation (all field bus channels are on the same potential) fieldbus connection: 2 x RJ45 equipped with two cable adapter RJ45 to Sub-D9M
Copyright IXXAT Automation GmbH
5
USB-to-CANV2 Manual, V1.0
Loading...
+ 9 hidden pages