IXXAT PC-I 04/PCI User Manual

Download

Manual

PC-I 04/PCI

Passive PC/CAN Interface

IXXAT Automation GmbH Leibnizstr. 15 D-88250 Weingarten

Tel.: +49 751 56146-0 Fax: +49 751 56146-29 Inte

rnet: www.ixxat.com

e-Mail

: info@ixxat.com

Support

In case of unsolvable problems with this product or other IXXAT products please contact IXXAT in written form by:

Fax: +49 751 56146-29 e-Mail: support@ixxat.com

Further international support contacts can be found on our webpage www.ixxat.com

Duplication (copying, printing, microfilm or other forms) and the electronic distribution of this document is only allowed with explicit permission of IXXAT Automation GmbH. IXXAT Automation GmbH reserves the right to

change technical da

ta without prior announcement. The general business

conditions and the regulations of the license agreement do apply. All rights are reserved.

Document number: 4.01.0057.20000 Version: 2.4

PC-I 04/PCI manual, Version 2.4

Contents

1 Introduction ................................................................................ 5

1.1 Overview ............................................................................. 5

1.2 Features ............................................................................... 5

1.3 Support ............................................................................... 5

1.4 Returning hardware ............................................................ 6

1.5 Block diagram ..................................................................... 6

2 Installation .................................................................................. 7

2.1 Software installation .......................................................... 7

2.2 Hardware-Installation ......................................................... 7

3 Configuration ............................................................................. 8

3.1 Settings on the interface .................................................... 8

3.1.1 Power supply via CAN-plugs ...................................................... 9

3.1.2 Connection to ground for measuring purposes .......................... 9

3.2 Design of the CAN-plugs ................................................... 10

3.2.1 Connecting the bus ................................................................. 10

3.3 Bus terminator .................................................................. 11

4 Architecture .............................................................................. 11

4.1 PC-side memory allocation ............................................... 11

4.1.1 Access to CAN-controllers ....................................................... 11

4.1.2 Resetting the CAN-controllers from the PC............................... 12

4.2 Triggering an interrupt on the PC ..................................... 12

4.3 Interrupt handling ............................................................ 12

Appendix .......................................................................................... 13

Appendix A .............................................................................. 13

Technical data .......................................................................... 13

Appendix B ............................................................................... 14

Sources of data sheets ............................................................. 14

Declaration of conformity ....................................................... 15

PC-I 04/PCI manual, Version 2.4

Introduction

1 Introduction

1.1 Overview

Congratulations on your purchase of the IXXAT-PC-CAN-interface PC-I 04/PCI, a high-quality electronic component developed and manufactured according to the latest technological standards.

This handbook is intended to familiarize you with your interface, also referred to in the following as PC-I 04/PCI. Please read this handbook before beginning with the installation.

1.2 Features

The most important technical features are as follows:

• Constructed as PCI-plug-in card

• 32 bit memory-mapped access (1024 bytes are required in the memory

address space for the CAN-controllers and 128 bytes each in the I/O address space and in the memory address space for the local configuration register)

• Basic address and interrupt via plug’n’play PCI-Bios

• One or two CAN-lines with Philips SJA1000 with 16 MHz clock

• CAN-bus connection in accordance with ISO 11898-2 high speed (as an

option galvanically isolated)

• Bus connection carried out separately for each CAN-controller

• Pin assignment according to CiA/DS-102

1.3 Support

For more information on our products, FAQ lists and installation tips, please refer to the support section of our website (

http://www.ixxat.de), which also contains

information on current product versions and available updates. If you have any further questions after studying the information on our website

and the manuals, please contact our support department. The support section on our website contains the relevant forms for your support request. In order to facilitate our support work and enable a fast response, please provide precise information on the individual points and describe your question or problem in detail.

If you would prefer to contact our support department by phone, please also send a support request via our website first, so that our support department has the relevant information available.

PC-I 04/PCI manual, Version 2.4

Introduction

1.4 Returning hardware

If it is necessary to return hardware to us, please download the relevant RMA form from our homepage and follow the instructions on this form. In the case of repairs, please also describe the problem or fault in detail on the RMA form. This will enable us to carry out the repair quickly.

1.5 Block diagram

PCI Interface

Controller

PLX PCI9050

CAN

Controller 1

SJA1000

CAN

Controller 2

SJA1000

CAN Bus

Interface

CAN Bus

Interface

INT#

CAN High

CAN Low

PCI-Bus

CAN High

CAN Low

AD[0..7]

INT A#

Fig. 1-1: Block diagram PC-I 04/PCI interface

PC-I 04/PCI manual, Version 2.4

Installation

2 Installation

2.1 Software installation

A driver is required in order to operate the interface. For the installation of the CAN driver VCI, please read the VCI installation handbook.

2.2 Hardware-Installation

Before you plug the PC-I 04/PCI into the PCI slot, you should install the software driver (see section 2.1).

For all work on the PC and interface, you must be statically discharged. Work must be carried out on an earthed, anti-static work mat.

Take the following steps in sequence:

(1) Switch the PC off and disconnect the mains plug. (2) Open the PC according to the instructions of the PC manufacturer and find a

suitable place to plug in. The interface is designed according to the PC-standard and can easily be built into the computer. Do not use force when plugging in.

(3) Make sure the interface sits tightly in the PC. (4) Close the PC; the hardware installation is now complete.

PC-I 04/PCI manual, Version 2.4

Configuration

3 Configuration

3.1 Settings on the interface

Figure 3-1 shows the position of the plugs, figure 3-2 the jumpers on the interface.

Fig. 3-1: PC-I 04/PCI interface – components side

PC-I 04/PCI manual, Version 2.4

Configuration

Fig. 3-2: PC-I 04/PCI interface – solder side

3.1.1 Power supply via CAN-plugs

With the solder jumpers JP4, JP5, JP33 and JP36, VCC (5 V) or GND can be connected to the CAN-plugs of the two CAN-lines. For this, the jumpers given in the following table are to be connected. The solder jumpers are on the solder side of the PC-I04/PCI.

Plug (X1, X2)

Pin – Signal

Default setting

CAN-

line 1

CAN-

line

6 - GND open JP5 JP33

9 - VCC open JP4 JP36

Attention: This voltage may be loaded with maximum 100 mA. With galvanically isolated bus connections, the signals GND and VCC are also

galvanically isolated from the power supply of the PC.

3.1.2 Connection to ground for measuring purposes

There is a connection on the PC-I 04/PCI for a ground pin. The abbreviation GND is marked on the board next to the drill hole.

PC-I 04/PCI manual, Version 2.4

Configuration

3.2 Design of the CAN-plugs

Two isolated high-speed bus attachments according to ISO 11898-2 can be mounted on the interface.

The signals of the first bus connection are connected to the 9-pin Sub-D-plug X1. If the second bus connection is printed, the signals for the CAN-bus of the se-

cond bus connection are connected to the header X2.

3.2.1 Connecting the bus

Signals of the 1st bus connection on the 9-pin Sub-D plug X1:

Pin no. X1 Signal name

1 2 CAN Low 3 GND 4 5 6 GND (JP5) 7 CAN High 8 9 VCC (JP4)

Signals of the 2nd bus connection on the 9-pin Sub-D plug X2:

Pin no. X2 Signal name

1 2 CAN Low 3 GND 4 5 6 GND (JP33) 7 CAN High 8 9 VCC (JP36)

With galvanically isolated bus connections, the signals GND and VCC are also galvanically isolated from the power supply of the PC.

PC-I 04/PCI manual, Version 2.4

Architecture

3.3 Bus terminator

On the PC-I04/PCI there are bus terminator resistors for the two bus connections. The bus terminator for the first bus connection is connected via the solder jumper JP6 and for the second bus connection with JP7. Bus termination is with a 120 Ohm resistor between CAN Low and CAN High.

On delivery, the bus connections are not active. Alternatively bus termination can also be made externally with the IXXAT

accessory “SubD9 connector with CAN bus terminator resistor“ (order number 1.04.0075.03000).

4 Architecture

4.1 PC-side memory allocation

The CAN-controllers are displayed directly in the memory range of the PC.

0000h

0100h

0200h

0300h

03FFh

1.CAN-Controller

Reset CAN1

2.CAN-Controller

Reset CAN2

(Basisadresse)

Fig. 4-1: PC-side memory allocation

4.1.1 Access to CAN-controllers

There can be up to two CAN-controllers of the type Philips SJA1000 on the interface.

The first CAN-controller is displayed in the range from 0000h to 00FFh, the second CAN-controller in the range of 0200h to 02FFh from the basic address of the card. When accessing the corresponding memory range, the CAN-controller is selected automatically. The basic address is allocated by the PCI plug-and-play BIOS.

The exact register description of the SJA1000 can be found in the corresponding Philips data sheets (web-addresses in Appendix ).

The Output Control Register of the CAN-controllers must be loaded with the value DEh or 5Eh.

PC-I 04/PCI manual, Version 2.4

Architecture

4.1.2 Resetting the CAN-controllers from the PC

By writing a random value to an address of the reset range (0100h to 01FFh for the first CAN-controller and 0300h to 03FFh for the second CAN-controller), a hardware reset is carried out on the corresponding CAN-controller.

4.2 Triggering an interrupt on the PC

The CAN-controllers can trigger an interrupt on the PC. Both CAN-controllers share one interrupt (INTA# of the PCI-interface).

The PCI plug-and-play BIOS allocates an interrupt to the card (IRQ3..IRQ15).

4.3 Interrupt handling

The card is transparent, which means that the interrupt signal on the PCI-bus (INTA#) is active when a CAN-controller issues an interrupt signal and it remains active until the signal on the CAN-controller is reset by an interrupt acknowledge by the PC. The PCI-bus interface chip PLX PCI9050-1 does not appear here.

It should be noted that the PCI-bus interrupt in the PCI-specification is defined as level-triggered.

PC-I 04/PCI manual, Version 2.4

Appendix

Appendix A

Technical data

The following data refer to the version of the PC-I04/PCI with two Philips SJA1000 CAN-controllers and two galvanically isolated bus connections.

Dimensions: 95 x 125 mm (without slot plate)

16 mm overall height Weight: approx. 100 g Operating temperature range:

-20 .. +70 °C

Power supply: 5V DC ± 5% Current consumption: typically 300 mA

max. 600 mA

Relative humidity 10 – 95 %, non-condensing CAN-controllers: Philips SJA1000

CAN transceiver: Texas Instruments SN65HVD251 or Philips PCA 82C251

ESD protection CAN-bus: 12kV (Human Body Model) Max. number CAN-bus nodes: 120 Galv. isolation bus connection: 1000 V DC between CAN1, CAN2 and internal logic Signal delay due to

galv. isolation: typically 50 ns

PC-I 04/PCI manual, Version 2.4

Appendix

Appendix B

Sources of data sheets

www.philips-semiconductors.com

CAN-controller Philips SJA1000:

www.

CAN-transceiver Texas Instruments SN65HVD251:

ti.com

www.plxtech.com

PCI-bus interface chip PLX PCI9050-1:

PC-I 04/PCI manual, Version 2.4

Appendix

Declaration of conformity

IXXAT Automation declares that the product: PC-I 04/PCI

with the article numbers: 1.01.0057.10100

1.01.0057.10200

1.01.0057.11110

1.01.0057.11220

do comply with the EC directives 2004/108/EC.

Applied harmonized standards in particular: EN 55022:2006 + A1:2007 EN 55024:1998 + A1:2001 + A2:2003

23.08.11, Dipl.-Ing. Christian Schlegel , Managing Director

IXXAT Automation GmbH Leibnizstrasse 15 88250 Weingarten

IXXAT PC-I 04/PCI User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual