IWS Dripper System Assembly Instructions Manual
Assembly Instructions
IWS Dripper System
IWS are proud to announce the launch of their professional
dripper system which comes complete in kit form. The IWS
Dripper System utilises the already successful technology of
the IWS Flood & Drain System but uses drippers as its main
delivery of nutrients to the plant. The minute timer supplied
with this system has been specially designed to run the large
pumps used in dripper technology and special stands are also supplied for the dripper assemblies.
All the pots can be connected to the main controller which will pump away all the waste nutrients to a
desired location out of the growing area. The dripper system uses the leading dripper technology from D.I.G
drippers allow 12 flood drippers to run from one location instead of drippers running all over the grow area.
The pots are made up of three parts:
1. A stand with a preset height and a 15 degree slope which allows all the water to drain back to the
main control tank which will then pump it to either to waste or back to the reservoir to be recalculated.
2. A base pot which incorporates a patented water tight sealing gland through which the nutrient is
delivered to the plant.
3. A separate drain mesh pot that allows even and controlled saturation of the growing medium, this
enables the pots to be removed with the plant intact without damaging the roots. Do not forget to fit
the sleeve inside the pot to stop any medium from washing out of the pot.
The IWS dripper timer works by reducing the sectional timers fifteen minutes segments down into minutes,
the pump in the reservoir tank is then plugged into the timer which turns the unit on/off as required. The
high pressure pump sends nutrient down the feed lines and up into the D.I.G dripper head which when
pressure is reached allows an even feed to the drippers, the nutrients then flow down through the medium
and into the run to waste brain which in turn will pump the waste to any desired location.
Firstly how
does it all
work?
T
U
V
Q
R
S
P
O
N
M
L
K
J
F
G
Assembly Instructions
IWS Dripper System
100 litre tank kit
A
E
B
C
Non return valve
Sealing dripper caps
D
F
G
1 x 6 pot dripper extension kit
Congratulations on your purchase! Here’s some more good news - setting up
your IWS Dripper System is easy! You should be ready to go in well under an
hour.
Before you get started, please check that you have all the necessary parts:
• 1 x nutrient tank with lid (please note there are different sizes of tank depending on the number of pots you have)
• Aqua king submersible pump (connected inside the nutrient tank)
• Inline pump filter and non-return valve (connected to the aqua king pump)
• Brain pot (with fixed pump inside) and lid
• IWS minute timer and double socket extension
• Inner pots (mesh)
• Outer pots (solid base)
• Pot stands (please note, pot stands are now round)
• 6 elbow fitting hose connectors (one for each end system pot)
• Tee fitting hose connectors (one for each middle line pot)
• 6 hose connectors (for brain pot)
• Sealing glands for each pot
• Black hosepipe - enough hosepipe is supplied to give you 1 metre for each pot
• There’s also a plastic tap attachment to modify the nutrient tank
- however this is not required to set up the system.
Dripper column
• 1 dripper stand
• 1 dripper column
• 12 dripper spikes
• 1 dripper hub
• 1 hose ‘T’ fitting
• 12 rubber dripper plugs
• 2 hose stopper plugs
• Dripper tubing
• 4 rubber washers
IF YOU THINK SOMETHING IS
MISSING PLEASE CONTACT
YOUR RETAILER.
E
C
B
A
H
H
I
I
J
V
T
R
U
S
Q
M
N
O
P
L
K
D
Loading...