Iwill XP4-Evo 1.2 User Manual

Mini Pentium 4 Barebone
User’s Manual
Version 1.1
Mini P4 Barebone Series
ii
User’s Manual
FCC Compliance Statement
This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television equipment reception, which can be determined by turning the equip­ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Move the equipment away from the receiver
Plug the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult an experienced radio/television technician for
This device complies with Part 15 of the FCC Rules. Operation is subjected to the following two conditions 1) this device may not cause harmful interference and 2) this device must accept any interference received, including interference that may cause undesired operation.
User’s Manual
additional suggestions
iii
Mini P4 Barebone Series
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representa­tions or warranties regarding the contents of this manual and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Furthermore, the manufacturer reserves the right to revise this publication or make changes in the specifications of the product described within it at any time without notice and without obligation to notify any person of such revision.
Trademarks
Microsoft and Windows are registered trademarks of Microsoft Corp. Intel and Pentium 4 are registered trade­marks of Intel Corporation. Other product names used in this manual are the properties of their respective owners and are acknowledged.
Copyright
iv
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer.
©Copyright 2003
User’s Manual
Table of Contents
1: Introduction ......................................................... 1-1
About This Manual ............................................................ 1-2
Package Contents ............................................................. 1-2
Getting Started .................................................................. 1-1
2: Installation ........................................................... 2-1
Installing a CPU ................................................................. 2-1
Installing System Memory ................................................. 2-7
Installing Internal Peripherals ............................................ 2-9
Installing an IDE drive .................................................. 2-9
Installing a CD-ROM .................................................. 2-10
Completing System Configuration ................................... 2-10
3: External Components ......................................... 3-1
Front Panel ........................................................................ 3-1
Rear Panel ........................................................................ 3-3
4: BIOS Setup ......................................................... 4-1
Running the BIOS Utility .................................................... 4-1
Entering Setup ................................................................... 4-2
System Information ........................................................... 4-2
General Configuration ....................................................... 4-3
Advanced Configuration .................................................... 4-4
System Specific Setup ...................................................... 4-4
Primary / Secondary IDE Drives ........................................ 4-5
Peripherals ........................................................................ 4-6
Power Management .......................................................... 4-6
PCI & PNP ......................................................................... 4-7
Hardware Monitor .............................................................. 4-7
Restore Default Settings ................................................... 4-8
Exit .................................................................................... 4-8
5: Drivers and Utilities ............................................. 5-1
Running the Power Installer Disc ...................................... 5-1
Drivers and Utilities Screen ............................................... 5-1
User’s Manual
v
Mini P4 Barebone Series
Drivers Installation Screen ................................................ 5-1
Software Utility Screen ...................................................... 5-2
Make Driver Screen ........................................................... 5-2
Appendix 1: Hardware Layout .............................. A1-1
Components ....................................................................A1-1
Connectors ...................................................................... A1-1
Jumpers ...........................................................................A1-1
Motherboard Layout ........................................................ A1-2
Motherboard Layout Key .................................................A1-3
JCMOS1: Clear CMOS Jumper ......................................A1-4
System Memory Socket ..................................................A1-5
CPU Socket & Cooling Fan / Heatsink Frame ................. A1-5
Expansion Slot ................................................................A1-6
PCI Expanion slot ...................................................... A1-6
AGP Slot .................................................................... A1-6
IDE1, IDE2: IDE Drive Connectors .................................. A1-7
ATX12V Power Connectors ............................................. A1-7
J2, J3: Internal USB Connectors .....................................A1-8
J4: AUX-IN/ CD-IN ........................................................... A1-8
J8: Audio Connector ........................................................ A1-9
JPANEL1: Front Panel Connector ................................... A1-9
JCFAN1, JSFAN1: System Fan Connectors ................. A1-10
Appendix 2: Specifications.................................... A2-1
vi
User’s Manual
IntroductionChapter 1
1: Introduction
The mini P4 barebone is a high-performance personal computer barebones system that supports the Intel® Pentium® 4 processor. The barebone’s motherboard has one DIMM memory socket that accommodates 200/266 MHz DDR
SDRAM (without AGP slot version) or 200/266/333MHz DDR SDRAM (with AGP slot version).
The without AGP slot model uses the latest Intel® 845GV chipset
or the Intel® 845GE chipset (with AGP slot version)
to integrate all system control functions.
Features of this system include support for:
Intel® Pentium® 4 processor
533/400 MHz system bus
Up to 1GB DDR SDRAM
One 32-bit PCI/33 MHz slot (without AGP slot version)
One onboard AGP slot (with AGP slot version)
Two USB 2.0 external ports on rear panel (stacked)
For a complete list of specifications, see Appendix 2, Specifications.
1 - 1User’s Manual
Mini P4 Barebone Series Chapter 1
About This Manual
This manual’s five chapters and two appendices cover the following topics:
Chapter 1, Introduction, provides a basic introduction to
the system and package contents.
Chapter 2, Installation, explains basic installation
procedures.
Chapter 3, External Components, describes external
components.
Chapter 4, BIOS Setup, describes setting the BIOS. Chapter 5, Drivers and Utilities, explains how to use the
bundled software drivers and utilities.
Appendix 1, Hardware Layout, describes the mother-
board layout, components, and configuration
Appendix 2, Specifications, lists the system’s technical
specifications.
1 - 2
Package Contents
The package contains the following items:
One Barebone
• IDE connector cables
• Power cord
• Three spare Jumper caps
• Power Installer software & utilities disc
• User’s Manual
Inspect the system; if any items are damaged or missing, contact Anyware Solutions Pte Ltd immediately.
User’s Manual
InstallationChapter 2
2: Installation
This chapter describes installing components and devices on the barebone’ motherboard. Please review each of the following procedures before you start. For the location and description of system components, please refer to Appendix 1, Hardware Layout.
Getting Started
The package contains the motherboard/chassis assembly, plus one box containing the Fan/Heatsink, and one box containing accessories.
1. Unpacking the package.
2. Remove the two smaller boxes and place to one side.
3. Remove the motherboard/chassis assembly, and
4. Unscrew the three thumbscrews at the rear of the barebone
5. Locate the CPU socket.
Installing a CPU
The motherboard supports the Intel Pentium 4 processor. Follow the procedures below to avoid damaging the CPU or motherboard.
User’s Manual
discard the foam and plastic packaging – or save it for recycling.
and remove the aluminum Housing.
2 - 1
Mini P4 Barebone Series Chapter 2
Selecting a Processor
This motherboard supports all Intel Pentium 4 processors. The motherboard’s BIOS automatically detects the required settings and configures the CMOS Setup Utility.
Installing the Processor
It is important to review all of the instructions before beginning the installation procedure. Carefully handle the processor by its edges, and take all precautions against electrostatic discharge. The boxed Intel Pentium 4 proces­sor comes with a Heatsink and Thermal Interface Material applicator. Non-boxed processors follow the same proce­dures, but the accessories may have a different appear­ance. The following illustrations are a generic representa­tion and may not show the components’ exact appearance.
Note that you install the CPU by reaching your hands and fingers through the chassis frame to manipulate the CPU and socket.
2 - 2
1. Unlock the socket by pressing the lever sideways, then lift it up to a vertical angle.
Step 1
User’s Manual
2. Position the CPU above the socket such that its marked corner matches the base of the socket lever.
Step 2
3. Press it firmly on the socket while you push down the socket lever to secure the CPU.
InstallationChapter 2
Step 3
User’s Manual
2 - 3
Mini P4 Barebone Series Chapter 2
4. After installing the CPU you need to apply the Ther­mal Interface Material (TIM) to the top of the installed CPU (Fig. 2) and remove the piece of tape from the Heatsink. The TIM is supplied in an applicator with the boxed Pentium 4 processors. The TIM secures the Fan/Heatsink to the CPU. However, if the Fan/ Heatsink already has a patch of TIM on its underside, you won’t need to apply additional TIM to the CPU (Fig. 1).
Step 4
The heatsink may have thermal interface material attached to the bottom as shown in Fig.1, or you may need to apply the thermal interface material using a syringe as shown in Fig.2.
2 - 4
Fig. 1
Be careful not to damage the thermal interface material.
Fig. 2
mPGA478B
Using the enclosed syringe apply all of the thermal interface material to the top of the processor.
User’s Manual
InstallationChapter 2
Installing the Fan/ Heatsink
To install the Fan/Heatsink assembly:
5. When installing the Fan/Heatsink and clip assembly it is important to make sure the Fan/Heatsink does not rotate or twist on the processor. Securing the Fan/ Heatsink while closing the clip lever will ensure the thermal interface material (TIM) is not damaged and the processor will operate correctly. The TIM is attached to the heatsink.
Step 5
1
A
6. Make sure to close the clip levers one at a time. Close
User’s Manual
the clip lever (1), while holding the top-side of the Fan/Heatsink with your other hand (A). Close the clip lever (2) while holding the top-side of the Fan/ Heatsink with your other hand (B).
Step 6
2
B
2 - 5
Mini P4 Barebone Series Chapter 2
7. Align the Heatsink and clip assembly with the Reten­tion Mechanism and place it on the processor. The Heatsink is symmetrical.
Step 7
C
D
8. With the clip levers in the up position (C), push down on all four clip frame corners to secure to the Reten­tion Mechanism hooks (D). Close the clip levers (E). The levers require force to be completely closed.
2 - 6
Connect the processor fan cable connector to the motherboard connector.
Step 8
E
User’s Manual
InstallationChapter 2
Installing System Memory
Review this section before installing memory modules.
Memory Specifications
The motherboards has one DIMM module socket that supports DDR SDRAM. Memory specifications are:
DDR SDRAM*
PC1600/PC2100 DDR SDRAM (without AGP slot version)
PC1600/PC2100/PC2700 DDR SDRAM (with AGP slot
version)
Unbuffered DDR SDRAM modules
Maximum up to 1GB system memory
Memory configuration options are:
Supports 64MB, 128MB, 256MB, 512MB, and 1GB
*Note: DDR SDRAM types include:
User’s Manual
modules
PC1600 at 200MHz
PC2100 at 266MHz
PC2700 at 333MHz
2 - 7
Mini P4 Barebone Series Chapter 2
Installing Memory Modules
To install a memory module, you insert a module into its socket and secure it with the socket retaining arms. The modules are notched so that you cannot insert them incorrectly. The BIOS recognizes the installed memory and configures the CMOS Setup Utility automatically.
Installing Memory Modules
To install memory modules:
1 Unlock a DIMM socket by pressing the retaining clips
outward.
2 Align the “notch” on the memory module to the
“break” on the socket.
2 - 8
Notch
Break
3 Firmly insert the module into the socket until the
retaining clips snap back into place and the module is properly seated.
4 Make sure the memory module is locked on the socket
with both retaining clips.
User’s Manual
InstallationChapter 2
Installing Internal Peripherals
After installing the CPU, Fan/Heatsink, and memory modules, you can install internal peripherals such as a hard disk drive (IDE/HDD), and CD-ROM drive. You may have to set the jumpers of each internal peripheral to either Master or Slave mode depending on whether you install more than one peripheral.
Important: Make sure the 110/220 switch on the back
panel is set to the appropriate voltage.
Installing an IDE drive
To install an IDE drive:
1 Set the required jumpers on the IDE drive according to
the instructions of the manufacturer.
2 Remove the 3-connector peripherals cable from the
accessories box and attach it to the blue connector IDE1 on the motherboard.
3 Bring the cable up and over the IDE drive and attach
Important: The IDE cable must be wrapped over the IDE
4. Secure the IDE drive to the chassis port by inserting
5. Connect an available power cable from the power
User’s Manual
the cable’s middle connector to the IDE drive. With the cable wrapped over the top of the IDE drive, slide the drive into the lower chassis port.
Drive to keep it from blocking the fan.
mounting screws in all the holes and tightening these screws with a screwdriver.
supply unit to the back panel of the IDE Drive. Note that the power cable is directional and can only fit one way.
2 - 9
Chapter 2Mini P4 Barebone Series
Installing the IDE Cable between CDROM and HDD
In vertical down direction the IDE Hard Disk Drive into lower bay and apply screws on each side of the bay to make sure Hard Disk was secured seated in correct place.Connect the power and IDE cable to the IDE Hard Disk. To ensure air-flow quality issue regarding thermal from CPU, the IDE cable will need
to be placed between IDE Hard Disk Drive and CDROM
CD Rom Drive
Hard Disk Drive
IDE Cable
User’s Manual
2 - 10
Chapter 2 Installation
Installing a CD-ROM
1 Set the required jumpers on the CD-ROM drive
according to the instructions of the manufacturer.
2 Attach the end of the peripherals cable to the CD-
ROM. The peripheral cable now connects both the IDE drive and the CD-ROM.
3 Slide the CD-ROM drive into the upper chassis port.
4. Secure the CD-ROM drive to the chassis by inserting mounting screws in all the holes and tightening these screws with a screwdriver.
5. Connect an available power cable from the power supply unit to the back panel of the IDE Drive. Note that the power cable is directional and can only fit one way.
1 2
Please adjust the button inside the case to fit the CDROM's button.
Slide the CD-ROM drive into the chassis from the top.
3 4
Attach the IDE cable and power cord to the CDROM.
Secure the CD-ROM drive to the chassis by inserting screws.
User’s Manual 2 - 11
Mini P4 Barebone Series Chapter 2
Completing System Configuration
To complete the system configuration:
1. Replacing the system housing cover and tighten the three thumbscrews on the rear panel.
2. Connect external peripherals such as a monitor, a keyboard, and a pointing device to the back panel.
3. Once you have completed final hardware installation, you can configure CMOS Setup Utility and Drivers, see the following chapters.
4. Install an operating system and support software—see related documentation.
2 - 12
User’s Manual
External ComponentsChapter 3
3: External Components
This chapter describes the external components of the barebone.
Front Panel
The features described below are conveniently located on the front panel for ease of use and accessibility.
Power Switch
(Power Indicator)
Reset Switch
(HDD Indicator)
Microphone
Earphones
USB 2.0
CD ROM Eject
CD ROM Play
Power Switch
The Power Switch lets you Power On and Shut Down the system. Press the switch for Power On. Press and hold the switch for 2 seconds to Shut Down the system.
User’s Manual
USB 2.0
3 - 1
Mini P4 Barebone Series
Reset Switch
The Reset Switch lets you shut down the system if you cannot use the operating system shut down procedure.
USB Ports
Two standard Universal Serial Bus (USB) ports each support several USB compatible devices such as pointers, keyboards, modems, and printers connected in series.
MIC
This mono microphone jack lets you connect an external microphone for use in voice mail recording, general note taking or for use with an internet phone.
Phones
This stereo ear phones jack lets you connect a set of headphones or a set of amplified speakers.
Power LED
The Power LED glows a steady light when the power is On, and blinks when the system is in Standby mode. There is no light when the power is off.
Chapter 3
3 - 2
HDD LED
The HDD LED displays the status of hard disk drive operation.
User’s Manual
External ComponentsChapter 3
Rear Panel
The Rear Panel’s components and their features are described below.
Cooling Fan
The Cooling Fan switches on when the system’s tempera­ture rises above a certain threshold.
Voltage Switch
The Voltage Switch lets you switch the system to operate at either 110V or 220V.
Power Switch
This power switch lets you power on the system from the rear panel.
User’s Manual
3 - 3
Mini P4 Barebone Series
Power Cord
Attach the power cord to this socket.
System Fan
The system fan begins operation when the system’s temperature rises past a certain threshold. Do not block this vent.
Audio Jacks
The audio jacks are for connecting external audio devices to the onboard audio subsystem.
The three audio jacks are:
SPK OUT: provides output to two stereo speakers, or the
Line In: provides audio input connector for an external
Chapter 3
Front Left and Right speakers in a 5.1 speaker system
audio source.
3 - 4
Mic: this jack is for plugging in a computer micro-
phone.
User’s Manual
External ComponentsChapter 3
USB Ports
There are two high-speed USB 2.0 ports, USB 0 and USB 1, for connecting either USB 1.1 or 2.0 devices to the system. These ports are for “Type A” USB cable connectors. It does not matter if the system is on when you connect or disconnect USB devices. See the graphic below.
LAN Port
The LAN Port is an RJ-45 connector for standard Cat 5 LAN cabling. The connector attaches to the onboard Realtek LAN controller. It does not matter if the system is on when connecting or disconnecting a LAN cable.
Printer Port
The Printer port connects the system to devices that have a parallel interface. This port is generally used to connect a printer to the system.
User’s Manual
3 - 5
Mini P4 Barebone Series
Monitor Port
The monitor port is a 15-pin connector for attaching a VGA monitor.
COM Port
The COM Serial port has a 9-pin connector and can operate at speeds up to 115,200bps. Do not connect or disconnect a serial port when the system is turned on.
Chapter 3
3 - 6
PS/2 Ports
The PS/2 ports are for a system keyboard and mouse or other tracking device. It is recommended that you do not plug or unplug devices when the system is on.
Mouse
Keyboard
User’s Manual
BIOS SetupChapter 4
4: BIOS Setup
After you have installed peripherals, configured the motherboard and assembled the system, you can power up the system.
The system uses the Award BIOS utility. The setup instructions for configuring the system’s BIOS (Basic Input Output System) are contained on this chip. The Award BIOS Utility lets you set system parameters, which are stored in nonvolatile CMOS RAM. This information is retained by battery backup when the system is powered off. The values stored in the CMOS configures the system each time the system is powered on.
Running the BIOS Utility
The BIOS Utility does not depend on an operating system to run. You run the utility by typing the <Del> or Delete key before the operating system boots up. The BIOS Utility Main Menu appears. You navigate the BIOS Utility using keyboard commands that are listed on the lower right portion of each screen.
Once you have fully configured the BIOS Utility you will rarely need to configure it again.
4- 1User’s Manual
Mini P4 Barebone Series Chapter 4
Entering Setup
Power up the system and press the <Del> key to enter the BIOS Setup main menu.
On entering Setup, “Main Menu” is the first screen displayed. Use the UP/DOWN arrow keys to highlight the desired menu item and press ENTER to select this item.
BIOS Setup Main Menu
4- 2
Use the arrow keys to select items. A description of each selection follows.
System Information
System Information offers general system information, such as: BIOS information, CPU type and speed, parallel and serial port I/O addresses, IDE drive information, cache memory size, total memory size and memory in each slot.
Use this information to verify if these components are installed and configured correctly.
User’s Manual
BIOS SetupChapter 4
General Configuration
The General Configuration screen lets you set time and date settings to suit your location. Set boot devices in the appropriate sequence. Power up options include Numlock, Primary VGA, and Boot Sector protection.
You can set a User and Supervisor password after en­abling the Password Required item.
Forgot the Password?
If you forget the password, you can clear the password by erasing the real time clock’s CMOS RAM. You can erase the CMOS RAM using the JCMOS1 jumper, see Appen­dix 1: Hardware Layout. After you have done so, hold down the <Del> key during boot up and enter BIOS setup to reenter user preferences.
General Configuration Screen
4- 3User’s Manual
Mini P4 Barebone Series Chapter 4
Advanced BIOS Features
The Advanced BIOS Configuration sets Virus Warning, memory test, CPU L1 and 2 cacheable, booting disk device settings, onboard LAN controller and BIOS write protec­tion. Unless you fully understand the function of these settings, it is better to leave the default settings.
Advanced BIOS Configuration Screen
4- 4
Advanced Chipset Features
The Advanced Chipset Setup screen configures the DRAM timing clock, the memory CAS latency, sytem turbo mode...
Unless you fully understand the function of these settings, it is recommended that you do not change the default settings.
User’s Manual
BIOS SetupChapter 4
Advanced Chipset Setup Screen
Primary / Secondary IDE Drives
The Primary / Secondary IDE Drives screens let you manually or automatically set up different IDE hard drives on two separate IDE channels – primary and secondary IDE channels.
Primary IDE Drives Screen
4- 5User’s Manual
Mini P4 Barebone Series Chapter 4
Peripherals
The Peripherals screen lets you enable and disable onboard peripherals controllers.
Peripherals Screen
Power Management
The Power Management screen lets you configure power management settings.
4- 6
Power Management Screen
User’s Manual
BIOS SetupChapter 4
PCI & PNP
The PCI & PnP screen configures Plug and Play and other PCI bus settings.
PCI & PnP Screen
PC Health Status
The PC Health Status screen shows information on the system’s voltages, fan rotations and temperatures.
Hardware Monitor Screen
4- 7User’s Manual
Mini P4 Barebone Series Chapter 4
Load Optimized Defaults
The Optimized Defaults Settings screen lets you reload the original manufacturer settings. The Restore Optimized Defaults lets the system start using the most reliable settings. Use this option when you can no longer boot the system due to changing, adding or removing hardware parts or peripherals.
4- 8
Restore Default SettingsScreen
Save to CMOS and Exit
After making your selections in the Setup program, save
your changes and exit BIOS Setup. Select Exit from the
main menu and choose the appropriate option.
User’s Manual
Drivers and UtilitiesChapter 5
5: Drivers and Utilities
The barebone comes bundled with a Power Installer CD-ROM disc that includes driver and utility software. This chapter describes installing and using this software.
Running the Power Installer Disc
The Power Installer CD-ROM install interface runs under Microsoft Windows 9X, NT 4.0, 2000, or XP. After inserting the disc into your CD-ROM drive the install interface loads automatically. Choose model selections. If it does not load, run the Power Installer directly from the disc by running Setup.
Drivers and Utilities Screen
from the
This screen has five selections. Choose a selection to open its respective screen, which are described below. The
User’s Manual selection opens the motherboard docu­mentation. Choose Exit to leave this screen.
Drivers Installation Screen
Click Driver Installation in the Drivers and Utilities
screen and the Driver Installation screen appears. Choose drivers in sequence to open their respective install pro­grams. Select the installation guides to review installation
information. When you are finished click Exit to leave
this screen.
User’s Manual
5 - 1
Mini P4 Barebone Series Chapter 5
Software Utility Screen
Click Software Utility in the Drivers and Utilities screen
and the Software Utility screen appears. To install the
Adobe Acrobat Reader software, click on the item you
wish to install and follow the instructions.
Clicking on the Hardware Monitor Utility lets you install
a program that gives access to information detected by the hardware monitor.
Make Driver Screen
Click Make Driver in the Drivers and Utilities screen and
the Make Driver utility screen appears. This utility gives you a convenient way to make driver floppy disks. You can use this utility to make driver disks for the LAN driver.
5 - 2
Make Driver Screen
User’s Manual
Appendix 1
Hardware Layout
Appendix 1: Hardware Layout
This chapter describes the motherboard layout and shows the location, function, and configuration of key compo­nents, including sockets, slots, connectors and jumpers. Before installing this motherboard read the following pages carefully for location and function of these items.
Components
The motherboard provides sockets, slots, and connectors for the installation of the CPU, memory, power supply, and PCI or AGP expansion cards.
Connectors
The motherboard’s connectors attach to IDE drives, CPU fan/heatsink, audio devices, and front panel features such as LEDs, speaker, and power switch.
Jumpers
The motherboard’s jumpers provide information to the operating system about installed options and system settings.
User’s Manual
A1 - 1
Mini P4 Barebone Series Appendix 1
Motherboard Layout
The motherboard components are shown below.
Layout
J8
JSFAN1
Expansion Slot
LAN Controller
DDR1
J4
JATXPWR1
mPGA478B
JCFAN1
IDE2
IDE1
I/O Controller
JATXPWR2
A1 - 2
J3
J2
JPANEL1
JCMOS1
User’s Manual
Appendix 1
Hardware Layout
Motherboard Layout Key
These components, connectors and jumpers are located in the motherboard layout graphic on the facing page.
Component Function
CPU mPGA478 CPU socket DDR1 DIMM socket for DDR SDRAM
Expansion Slot PCI expansion slot (Without AGP Slot version)
AGP expansion slot (With AGP Slot version)
Connectors Function
JATX PWR1 Connector for power supply JATX PWR2 ATX power connector JPANEL1 Front panel feature connector J2 Internal USB connector J3 Internal USB connector J8 Audio connector J9 Aux In/CD In JCFAN1 CPU cooling fan power connector JSFAN1 Auxiliary Fan connector IDE1, IDE2 IDE drive connectors
Jumpers Function
JCMOS1 Clear CMOS
User’s Manual
A1 - 3
Mini P4 Barebone Series Appendix 1
JCMOS1: Clear CMOS Jumper
This jumper switch, JCMOS1, clears the CMOS Setup configuration that is stored in the real-time clock’s CMOS memory. If configuration becomes corrupted, or if the CMOS settings are changed to an unsuitable configuration, the motherboard may not work properly. JCMOS1lets you delete the configuration data stored in CMOS memory and reset the CMOS to the Optimized Defaults.
Follow the procedure below to clear CMOS memory.
1 Turn off and unplug the system and remove the
system housing cover.
2 Set JCMOS to the Clear CMOS position by placing the
jumper cap over pins 2 and 3 for one minute.
3 Return the jumper cap to Normal setting, pins 1 and 2.
4 Replace the system housing cover, plug in the system
and power on.
5 Run the CMOS Setup Utility and load the Optimized
Defaults. Make any custom settings you require.
A1 - 4
6 Save the settings as you exit the program and restart
your computer.
1
2
3
Normal(Default)
1
2
3
Clear CMOS
User’s Manual
Appendix 1
Hardware Layout
CPU Socket & Cooling Fan / Heatsink Frame
The mPGA478B CPU socket supports a 478-pin Intel Pentium 4 processor. The Pentium 4 CPU requires a cooling fan/heatsink, which attaches to the board using a retention mechanism mounting frame. See the section on installing the CPU in Chapter 2.
mPGA478B
The mPGA478B CPU socket is located within a cooling fan/ heatsink frame.
System Memory Socket
This DIMM system memory socket supports 200MHz (PC1600) or 266MHz (PC2100) DDR SDRAM system memory modules. See the section on installing memory in Chapter 2.
DDR1
DDR SDRAM System Memory Module
User’s Manual
A1 - 5
Mini P4 Barebone Series Appendix 1
Expansion Slot
The motherboard’s expansion slot is either a 32-bit PCI
(without AGP slot version) or an AGP slot.
PCI Expanion slot
The PCI expansion slot on the motherboard lets you install additional system hardware via add-on cards. There is one 32-bit, 33MHz slot that is compliant with PCI 2.1/2.2 on this motherboard.
PCI1
PCI Expansion Slot
AGP Slot
The AGP slot is for the exclusive use of high speed AGP video display cards. This AGP slot supports AGP4X cards. This slot only supports 1.5V devices. Do not use a 3.3V AGP card with this motherboard.
A1 - 6
AGP
AGP Expansion Slot
There is only one expansion slot on this motherboard. It is either a PCI slot or an AGP slot .
User’s Manual
Appendix 1
Hardware Layout
IDE1, IDE2: IDE Drive Connectors
The two IDE drive connectors are marked IDE1, the primary channel, and IDE2, the secondary channel. Each connector supports two drives, a Master and a Slave.
IDE1
IDE2
IDE Drive Connectors
ATX12V Power Connectors
The two power connectors let you attach two leads from an ATX12V power supply to the motherboard. The ATX12V standard requires a 20-pin ATX connector plus a 4-pin ATX12V connector.
Insert the 20-pin lead of the ATX12V power supply into the first 20 holes of the JATXPWR2 power connector leaving the last four empty. Insert the 4-pin ATX12V lead into the JATXPWR1 power connector.
User’s Manual
ATX12V
1
4
2
JATXPWR2
Main Power Connector
13
1
JATXPWR1
Secondary Power Connector
3
2
4
A1 - 7
Mini P4 Barebone Series Appendix 1
J2, J3: Internal USB Connectors
These connectors, J2 and J3, let you attach internal USB devices.
2 4 6 8 10
2
1 3 5 7
Pin Assignment 1: USB_VCC2 3: USB_D2­ 5: USB_D2+ 7: GND 9: NC
Pin Assignment 2: USB_VCC2 4: USB_D3­ 6: USB_D3+ 8: GND 10: FUSB_CO-OUT
J2: Connector Pin Assignments
2 4 6 8 10
3
1 3 5 7
Pin Assignment 1: USB_VCC2 3: USB_D4­ 5: USB_D4+ 7: GND 9: NC
Pin Assignment 2: USB_VCC2 4: USB_D5­ 6: USB_D5+ 8: GND 10: FUSB_CO-OUT
J3: Connector Pin Assignments
J4: AUX-IN/ CD-IN
This connector, J4, lets you attach audio-in cables from internal peripherals, such as a CD-ROM or DVD-ROM drive. The connector provides audio input connection between a device and the integrated audio subsystem.
J4
4 3 2 1
Pin Assignment 1: Left Channel 2-3: GND 4: Right Channel
A1 - 8
J4: AUX-IN/ CD-IN
User’s Manual
Appendix 1
Hardware Layout
J8: Audio Connector
This connector, J8, lets you attach audio-out connectors to peripherals.
J8
1 9
Pins Function 5-6: Audio Line R 9-0: Audio Line L
JPANEL1: Front Panel Connector
This connector, JPANEL1, connects the following system housing front panel features:
Reset Switch (Reset in diagram)
IDE device LED (IDE LED in diagram)
ACPI Suspend LED (ACPI in diagram)
Power Switch (Power On in diagram)
System Activity LED (System LED in diagram)
Housing-mounted Speaker (Speaker in diagram)
13
1
Power On
System LED
+
IDE LED
ACPI
Speaker
++
24
12
Reset
User’s Manual
JPANEL1: Front Panel Connector
Pin Assignments
A1 - 9
Mini P4 Barebone Series Appendix 1
JCFAN1, JSFAN1: System Fan Connectors
These 3-pin connectors provide power to the CPU cooling fan (JCFAN1), and to another system cooling fan (JSFAN1). These connectors support fan speed monitor­ing. A temperature monitor detects the CPU and internal system temperatures. You can set a system shutdown temperature in the PC Health section of the CMOS Setup Utility.
123
JCFAN1
Pin Assignment 1: GND 2: +12V 3: Sensor
JSFAN1
Pin Assignment 1: GND 2: +12V 3: NC
System Cooling Fan Connectors
123
A1 - 10
User’s Manual
SpecificationsAppendix 2
Appendix 2: Specifications
Technical specifications are listed below.
Processor
Supports Single Intel Pentium 4 processor System Bus: 100MHz/133MHz Auto detects CPU type, external clock and multiplier CPU external clock adjustment at 1MHz/step by BIOS.
CPU Power
Follows VRM 9.0 spec VRD design
Memory
PC1600/PC2100 DDR SDRAM Unbuffered DDR SDRAM Supports single DIMM up to 1GB
Chipset
North Bridge: Intel 845GV/ Intel 845GE South Bridge: ICH4 Winbond Super I/O : W83627HF
AGP (With AGP version only)
One AGP slot AGP 4X Compliant
User’s Manual
A2 - 1
Mini P4 Barebone Series Appendix 2
PCI (wih PCI version only)
One 32bit PCI/33MHz slot PCI 2.1/2.2 Compliant
LAN
RealTek LAN 8100 onboard One RJ-45 connector
USB 2.0
Two USB 2.0 external port on the back panel (stacked) Two USB 2.0 external ports by pin header for the front panel
Audio
AC’97, RealTek ALC655 One audio connector at rear panel to support LINE IN/ LINE OUT/MIC IN/Game Port One 4-pin CD-ROM Audio In header One 4-pin AUX header Supports audio connectors on front panel (MIC/ Earphone)
A2 - 2
General I/O
Two IDE connectors (Bus Master with Enhanced) to support Ultra DMA 33/ATA66/ATA100 IDE drives and ATAPI compliant devices
One UART connector One 25pin ECP/EPP Parallel Port One PS/2 Keyboard One PS/2 Mouse One internal Smbus connector One internal WOL connector
BIOS
Award BIOS
User’s Manual
SpecificationsAppendix 2
Flash write Protection for BIOS Support ACPI S1, S3 BIOS setup features Auto configuration for IDE hard disk types Multiple boot options
Power Supply
200W
System Management
Winbond hardware monitor One 3-pin CPU Fan header Three 3-pin Chassis Fan headers One CPU temperature sensor Seven Voltage monitoring (Vcore, +1.5V, +2.5V, +3.3V, +5V, +12V, -12V, Battery, 5VSTB) One 3-pin Chassis intrusion header
Form Factor
Mini System form factor Stacked PS/2 Mouse/Keyboard ports Stacked RJ-45 on two USB2.0 ports Stacked one parallel on serial port and VGA port Stacked Line-in/ Line-out/ Mic
Other
Support AC power failure
Miscellaneous
1. ACPI 1.1 2. PC2001
3. PCI 2.2 4. APM 1.2
7.
9. FCC class B
10. CE mark 89/336/ECC(EMV) and acc. To EU
User’s Manual
WfM 2.0 8. DMI 2.0
A2 - 3
Loading...