Iwata FREESTYLE AIR Operating Manual

IFS AC ADAPTER IFS HOSE
OPERATING MANUAL • 取扱説明書手动操作
www.iwata-airbrush.com
Available Separately • 別売り分开采购
ENGLISH • 日本語中文
Airbrush Holder
エアーブラシ ホルダ
Anti-Vibration Base
防振ベース
Rechargeable NiMH Battery 充電可能NiMHバッテリー 可用 NiMH电池充电
Air Hose
エアホ ース
空气管
REV2 9/15
Air Hose Connector
エアホ ースコネクタ
空气管接头
Compressor Unit
コンプレッサユニット 空压机套装
Power Adapter Input
電源差込口
电源插入口
Power Adapter Input
電源差込口
电源插入口
Rubber Feet (Back of Compressor)
ゴム足(コンプレッサ背面)
橡胶支脚(空压机背面)
Portable Size • 持ち 運 び サイズ
尺寸 : 4.2 x 6.6 x 2.2 in (106 x 167 x 57 mm)
Portable Weight •
持ち運び 重量
拿着时的重量
: 1.7 lbs (766 g)
Decibel Rating •
騒音値噪音值:
~63-65dB With Air Hose and Airbrush
ホ ース・エアーブラシ付き 有空气管和喷笔
• On/Off Rolling Switch With 3-Speed Adjustment
• 3段階スピード調節機能付き回転
 式オンオフスイッチ
• 3速调节开关旋转调节阀
IFS AH IFS BATTERY
Vibration Dampening Pad
防振マット
减震板
AC Power Adapter With International Plugs (100-240V~50/60Hz) インタ ーナショナルプ ラグ 付AC電源アダプタ 交流整流器,国际通用插头
充電中はライトの色は下記を示します:  オレンジ:充電中
緑点滅:1時間以内で完全に充電されます
コンプレッサ運転中はライトの色は下記を示します:  緑:十分に充電されています  オレンジ:充電中
赤:充電が切れそうです
ON/OFFスイッチとバッテリー端子の保護テープをはがしてください。バッテリ ーを2時間で完全に充電してください。
バッテリーを反時計回りに1/8回転しコンプレッサから外してください(A)。適 切な電源コネクタを電源アダプタに取り付けてください。電 源アダプタをコン セントに差し込んでください(100‒240v)。電源アダプタのコードをバッテリー 上部に差し込み、2時間充電してください(B)。
ご使用の前に
WARRANTY
The Iwata Freestyle Air battery-powered airbrush compressor is warranted against all manufacturing defects of material and manufacture or workmanship for a period of ONE year from the date of purchase. (Please keep your sales receipt.) Any part or material that is or becomes defective so as not to be usable within this period will be repaired or replaced. This warranty does not cover damage caused by negligence, a compressor or battery that has been altered or abused in any way or a battery that has been left in an uncharged state for more than 45 days.
Contact your local Anest Iwata Aliate for warranty details and procedures at www.iwata-airbrush.com
日本語
The indicator light on the battery will show the following colors when charging: Orange – Battery is charging
Flashing Green – Battery is fully charged within 1 hour
The indicator light on the battery will show the following colors while the compressor is running:
Green – Battery has maximum charge
Orange – Battery has a good charge
Red – Battery needs to be recharged
REMOVE PROTECTIVE TAPE FROM ON/OFF ROLLING SWITCH AND BATTERY TERMINAL. FULLY CHARGE THE BATTERY FOR 2 HOURS.
Dismount the battery from the compressor unit by turning it counter-clockwise 1/8 turn (A). Determine the appropriate international plug and connect it to the power adapter. Plug the power adapter into an electrical outlet (100–240v). Then plug the power adapter cord into the top of the battery and charge for 2 hours (B).
BEFORE USING
TROUBLESHOOTING
1. Remount the charged battery onto the bottom of the compressor unit by aligning the tabs on the battery to the tabbed hole on the compressor unit. Push together and turn the battery clockwise 1/8 turn (C). You can power the compressor by using either the battery or by plugging the power adapter directly into the compressor unit. (The battery will charge when attached to the plugged in compressor unit only when the compressor unit is not running. Normal charge time for a full battery is within 1 hour. Spare batteries are available for longer running times.)
2. If using the compressor upright, place the bottom of the unit in the anti-vibration base. The base can be used with the battery attached (D) or with just the compressor unit (E). If lying at, place the side of the compressor unit with the rubber feet onto the vibration dampening pad (F).
3. Mount the dual position airbrush holder onto the unit. Use the L-shaped mounting tab when the compressor is in an upright position (G). Use the straight mounting tab when the compressor is lying at (H).
4. Screw one end of the air hose onto the compressor unit and the other end onto your airbrush and hand-tighten. Both ends of the air hose are the same. (If using a brand of airbrush other than Iwata, you may need an air hose adapter - not included.) The air hose provided is designed to work specically with the Iwata Freestyle Air Battery-Powered Airbrush Compressor. Do not use other air hoses.
Slowly turn the on/o rolling switch in any direction until the unit turns on. The rst setting is HIGH with a green-lit Iwata (I). Slowly turn the rolling switch again and the unit setting turns to MEDIUM indicated by a yellow-lit Iwata (J). By rolling the switch a third time, the unit setting turns to LOW indicated by a red-lit Iwata (K). The fourth time the switch is rolled, the compressor turns o. Deciding which pressure setting to use will depend upon the combination of application, viscosity of liquid being sprayed and model of airbrush. Test all 3 speeds to determine which will work best for you. Intended for thinner mediums.
• Compressor run-time with the battery is approximately 45 minutes at 10 psi working pressure. Times will vary depending upon application, liquid medium being used and model of airbrush.
• Always recharge battery after use.
• For best care of the battery, store the battery with the power adapter plugged into an electrical outlet. The battery can be charging either on or o the compressor.
• Do not store battery uncharged for any period of time. Fully charge the battery at least once a month. Failure to do so may void the warranty.
• Do not dispose of the battery in household waste. Dispose of according to local environmental regulations.
RECHARGEABLE NiMH (NICKEL-METAL HYDRIDE) BATTERY, 1600MAH
1. The compressor turns o while running. The Iwata Freestyle Air is
designed to automatically turn o after 9 minutes of constant running. To restart, slowly turn the rolling switch in any direction until the unit turns on.
2. The compressor will not turn on. Slowly roll the on/o rolling switch more
than once. If the rolling switch is turned too fast, the unit may not turn on. If compressor still will not turn on, the battery may need to be charged. If using the power adapter on the compressor unit, be sure the correct international plug is rmly mounted into the power adapter and then rmly attached to a working electrical outlet. Be sure the power adapter cord is rmly plugged into the compressor unit.
3. The compressor is running but no air is owing through the airbrush.
Check the air hose attachment on the compressor and airbrush to make sure there is no air leak. Check the air hose for cracks or damage. Remove the air hose from the airbrush and see if there is air owing through the air hose. If air is owing then your airbrush may be clogged.
4. The battery will not charge. Be sure the power adapter cord is rmly
plugged into the battery. Check that the correct international plug is rmly mounted into the power adapter and then rmly attached to a working electrical outlet. If battery was stored with a low or no charge for a long period of time it may be damaged.
SET UP
1. 充電したバッテリーの突起をコンプレッサ下部の穴に差し込み時計回りに
1/8回転して取り付けてください(C)。コンプレッサにはバッテリーか電源をコ ンプレッサに直接つなぐことで電力を供給できます。(コンプレッサに電源を 直接つないだ状態では、バッテリーはコンプレッサが稼働していない時だけ 充電されます。通常1時間以内で充電が完了します。)
2. コンプレッサを立てて使う場合は防振ベースの上に載せてください。ベー スはバッテリーを取り付けた状態でも使用できますし(D)、コンプレッサだけ の状態でも使用できます(E)。もし横に倒して使う場合はゴム足がついた面 を下にし防振マットの上に置いてください(F)。
3. エアーブラシホルダを取り付けてください。コンプレッサを立てて使う場合 はL字部分を差し込んでください(G)。横に倒して使う場合は真っ直ぐの差込 口を使ってください(H)。
セ ット ア ッ プ
USE
ENGLISH
A
B
C
D
E
I
J
K
~7-19 psi / 0.48-1.31 bar /0.05-0.13 MPa
~6-17 psi / 0.41-1.17 bar /0.04-0.12 MPa
~5-10 psi / 0.28-0.69 bar /0.03-0.07 MPa
Suggested applications and approximate psi for each high-performance, low pressure setting are as follows:
推奨用途と圧力は次の通りです: 每个高性能和低压设定建议的应用和大致压力如下:
保証
Iwataフリースタイルエアー  バッテリー式エアーブラシコンプレッサ は購入 日から1年間(領収書を保管ください)あらゆる製造上の欠陥に対して保証を 行います。この期間に生じた不良品に対しては修理あるいは交換が行われま す。お客様が注意事項を守られない場合や不注意による故障、コンプレッサ やバッテリーに対する改造による故障、45日以上バッテリーが充電されてい ない状態で放置されたことによる故障は保証の対象外となります。
保証に対するお問い合わせは各地のアネスト岩田までお問合せいただくか URLをご 参 照 くだ さ い 。www.iwata-airbrush.com
トラブ ル シュ ー ティン グ
1. 運転中にコンプレッサが止まる。Iwataフリースタイルエアーは9分間の連 続運転後に自動で停止するように設計されております。リスタートするには、 起動するまでどちらかの方向にゆっくりスイッチを回してください。
2. コンプレッサが起動しない。どちらかの方向にスイッチをゆっくり一回以上
回してください。もし回すのが早いと起動しないこともあります。それでも起動 しない場合はバッテリーの充電が必要かもしれません。電源アダプタを使用 している場合は正しいプラグを使っているか、コンセントにしっかり接 続して
いるか確認ください。コードがコンプレッサにきちんと差し込まれているか確
認ください。
3. コンプレッサは動いているがエアーブラシから空気が出てこない。 空気
漏れがないかホースのエアーブラシ側とコンプレッサ側の接続部分を確認く
ださい。ホースに亀裂や破損がないか確認ください。エアーブラシを外してホ ースの先から空気が出ているか確認ください。ホースから空気が出ていれば エアーブラシに問題があるかもしれません。
4. バッテリーが充電され ない。電源アダプタがバッテリーにしっかり差し込ま
れているか確認ください。適切なプラグを使用しているか、コンセントにきち んと差し込まれているか確認ください。バッテリーが充電切れ或いは充電が
少ない状態で長時間放置されていた場合は故障しているかもしれません。
4. エアホースの片方をコンプレッサに、もう片方をエアーブラシに手締めで 取りつけてください。エアホースの両端は同じサイズです(もしIwataエアー ブラシ以外をご使用の場合は別のジョイントが必要な場合もあります)。付属 のホースはIwataフリースタイルバッテリー式コンプレッサ専用に設計され ております。別のエアホースはご使用にならないでください。
On/Offスイッチをどちらかの方向にゆっくり回転します。最初はIwataロゴが 緑になる、圧力が「高」に設定されています(I)。さらにゆっくり回 転 すると Iwataロゴが黄の、圧力が「中」になります(J)。さらに 回 転 するとIwataロゴが 赤 の 、圧 力 が「 低 」に な り ま す( K)。さ ら に 回 転 さ せ るとコンプレッサの運転が 止まります。適切な圧力は用途、塗料の粘度、エアーブラシの型式 などにより 決定します。すべての圧力設定を試して最適な圧力を決定してください。粘度 の低い液体向けです。
•バッテリーでのコンプレッサ運転時間は10psi(約0.07MPa)で45分が目安
ですが、アプリケーション、塗料、ご使用のエアーブラシの型式によって多少 変化します。
•使用後は毎回充電してください。
•バッテリーに最適な保管方法として、電源アダプターを電源につないだ状 態で保管してください。バッテリーはコンプレッサのオン・オフに関係なく 充電されます。
•いかなる時もバッテリーを充電していない状態で保管しないでください。最 低でも月1回はバッテリーを完全に充電してください。これらを怠った場合 は保証対象外となります。
•バッテリーは一般ごみと一緒に捨てないでください。各地域にて指定され た方法で廃棄してください。
充電式NiMH(ニッケル・水素充電池)バッテリー、 1600MAH
使う
PROBLEMI FREQUENTI
LOW • HIGH •
MEDIUM •
PSI MPa BAR CFM LPM PSI MPa BAR CFM LPM PSI MPa BAR CFM LPM
NEO CN 19 0.13 1.31 0.09 2.5 18 0.12 1.24 0.08 2.3 10 0.07 0.69 0.08 2.2 Revolution CR 9 0.06 0.62 0.12 3.5 8 0.06 0.55 0.12 3.5 5 0.03 0.34 0.11 3.1 Eclipse CS 7 0.05 0.48 0.13 3.8 7 0.05 0.48 0.13 3.7 5 0.03 0.34 0.12 3.3 Hi-Line CH 10 0.07 0.69 0.12 3.5 9 0.06 0.62 0.12 3.5 6 0.04 0.41 0.11 3.1 Kustom TH-Fan 6 0.04 0.41 0.12 3.5 6 0.04 0.41 0.12 3.4 5 0.03 0.34 0.11 3.0 Kustom TH-Round 12 0.08 0.83 0.10 2.7 11 0.08 0.76 0.09 2.6 9 0.06 0.62 0.08 2.4
Working Pressure/Air Flow With Iwata Airbrushes
使用圧力/Iwataエアーブラ シでの空気量
Iwata喷笔的工作压力/空气 流量
Model
別売り • 分开采购
充电时指示灯会显示以下颜色:
橘色:电池正在充电 绿色闪烁:电池将在一小时内充满
空压机运转时,电源指示灯会显示以下颜色:
綠燈亮 - 代表電池處於完全充飽狀態 橘燈亮 - 代表電池處於正常狀態, 還不需要充電 紅燈亮 - 代表電池需要充電
ON/OFF转动开关和蓄电池组处移除保护带。满电电池可使用2小时。
逆时针旋转1/8圈可从空压机装置下卸除电池。确定合适的国际插头然后连 接到变压器。然后把变压器电源插到电源输出端(100-240V)。然后把变 压器连接到电池前端充电2小时。
使用前
中文
H
H
G
G
F
Loading...
+ 5 hidden pages