Page 1
HEADBOARD
Thank you for purchasing the
HEADBOARD！！！！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step by step
instructions.
2.Owing to the size and weight of the headboard, we recommend that it is assembled by two adults, on a carpeted
or padded area, in the room that it is intended for. Approx assembly time: 30 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that has been provided.
6.Please keep all fitting out of reach of children.
Co
mponent:
Hardware:
A
B
C
1
Bolt M8x45mm x4
Flat Washer M8xD22mm x4
Allen Wrench M5 x1
1
dboard x1
Hea
e may vary)
(Styl
2
2
2
Page 1 of 6
Low Post x2
Page 2
HEADBOARD
STEP 1:
Put
the Headboard (1) upside down on a carpeted or padded area by two adults
Then insert the Low Posts (2) into the bottom of Headboard (1) and align pre-drilled Low Post (2) holes to the predrilled Headboard (1) Holes according to your desired headboard height.
Attach each of Low Post (2) by using 2 piece of Flat Washer (B) and 2 pieces of Bolt (A) from the holes on the back
of Low Post (2) and Headboard (1). Tighten with Allen Wrench (C).
Ba
1
ck
C
2
A
B
Back
1
2
2
Ax
4 Bx4 Cx1
STEP 2:
Carefully turn up the assembled He
2
Hardware & Tool required
adboard (1) by two adults.
NO
Assembly is completed. The headboard is ready to use now!
TE:
Hardware may loosen over time. Periodically check that all connections are tight.
Page 2 of 6
Page 3
CONNECTING HEADBOARD TO BED FRAME
ASSEMBLY INSTRUCTIONS
OPTION 1
OP
TION 1
H
ardware:
A
B
Bol
t M6x45mm x4
Bol
t M6x65mm x4
Component:
C
D
E
F
1
Flat Washer M6xD22mm x8
Spring Washer M6 x4
He
x Nut M6 x4
Allen Wrench M4 x1
Headboard x1
1
(Style may vary)
2
OPTION 1
2
Page 3 of 6
Frame x1
Bed
Page 4
CONNECTING HEADBOARD TO BED FRAME
No
Extra hardware were provided for attaching the headboard to your Bed Frame (use is optional).
te:
STEP 1:
Li
ne up the Bed Frame (2) board’s pre-drilled holes to match those of the Headboard (1) .
Secure the Headboard (1) to the Bed Frame (2) by using 2 pieces of Bolt (B) for the thicker Bed Frame (2), and 2 pieces
of Bolt (A) for the thinner Bed Frame (2).
Before inserting each bolt, place 1 piece of Spring Washer (D) and Flat Washer (C) on each bolt. Then fit 1 piece of Flat
Washer (C) on the bolt as it protrudes through the other side of the Bed Frame (2).
Place 1 piece of Hex Nut (E) after the Flat Washer (C) at the end of each bolt. Then tighten the Bolts (A or B) by
using the Allen Wrench (F).
Repeat the same procedure for each bolt and each side of the Bed Frame (2).
1
1
E
C
2
A
or Bx4 Cx8 Fx1 Ex4 Dx4
STEP 2:
refully position the assembled bed to the desired location by four adults.
Ca
F
B
C
D
2
Hardware & Tool required
NOTE:
As
sembly is completed. The bed is ready to use now!
Hardware may loosen over time. Periodically check that all connections are tight.
Page 4 of 6
Page 5
CONNECTING HEADBOARD TO BED FRAME
AS
SEMBLY INSTRUCTIONS
OPTION 2
This is assembly instruction for Headboard connect toBed Frame
Note:
Component:
OPTION 2
Hardware:
A
B
C
D
F
Bol
t M6x45mm x4
Bolt M6x65mm x4
Flat Washer M6xD22mm x4
Spri
ng Washer M6 x4
Allen Wrench M4 x1
1
Headboard x1
(Style may vary)
1
OPTION 2
2
2
Be
d Frame x1
(Style may vary)
Page 5 of 6
Page 6
CONNECTING HEADBOARD TO BED FRAME
STEP 1:
Line up the B
Secure the Headboard (1) to the Bed Frame (2) by using 2 pieces of Bolt (B) with 2 pieces of Spring Washer (D), 2 pieces
of Flat Washer (C) for the thicker Bed Frame (2), and 2 pieces of Bolt (A) with 2 pieces of Spring Washer (D), 2 pieces of
Flat Washer (C) for the thinner Bed Frame (2).
Then tighten the Bolts (A or B) by using the Allen Wrench (F).
Repeat the same procedure for each bolt and each side of the Bed Frame (2).
ed Fame (2) board’s pre-drilled holes to match those of the Headboard (1).
2
1
2
1
C
D
A
F
A
or Bx4 Cx4 Dx4 Fx1
STEP 2:
Carefully position the assembled bed to the desired location by four adults.
A
ssembly is completed. The bed is ready to use now!
NOTE:
Hardware may loosen over time. Periodically check that all connections are tight.
Hardware & Tool required
ge 6 of 6
Pa
Loading...