Page 1
Product User Manual
Product User Manual
Please read the manual carefully before using this product, and keep it properly for future
use!
Thank you for purchasing this product. We have been committed to the R&D and design
of lighting products and LED photoelectric products. "Providing customers with satisfactory
products and services" is our unswerving enterprise pursuit. For this reason, we continue to
innovate and forge ahead!
Safety guidance and precautions
Safety factors are fully considered in the design of this product, but improper installation
and use may cause unnecessary losses and injuries. For your safety and better use of this
product, please read the operating instructions carefully before use and strictly follow the
procedures!
The applicable power supply of this product is AC85-265V-50Hz;
Do not install it directly above high temperature objects such as heaters, open flames and
gas; Do not install in a steam room or wet environment such as celling with wet lime;
Please cut off the power supply before replacing the light source or removing the
lampshade, and do not operate until the lamp is completely cooled. Do not operate with
wet hands or hot line job! Do not disassemble or refit lamps at will.
The high heat generated during the use of the lamp may cause danger. Please do not
place flammable items around the lamp, and do not touch the light source and lampshade
directly with your hands;
Stop using lamp immediately when an abnormal situation occurs in the process of using
the lamp, cut off the power supply, and ask professional technicians for maintenance.
Please entrust professional qualified personnel to install lamps and lanterns during
installation.
Use
Do not touch or scratch the surface of lamps with hard objects;
Do not hang articles or bake clothes on lamps and lanterns.
For your safety, this product needs to be installed by professional technicians!
Please wear gloves when installing, and remove stains and sweat stains on hardware in
time; Lamps and lanterns with grounding symbols must be reliably and permanently
grounded when installed;
Fixed lamps and lanterns must be fixed firmly during installation to ensure that the installed
medium can bear the weight of the lamp body. The lamp shall be pulled for 3 times with a
pulling force 5 times the weight of the lamp body to ensure that the lamp will not fall after
installation;
Please refer to the following installation instructions for specific installation operation:
1.Remove the ceiling
lamp cover.
2.Drill holes according
to the screw hole
position and connect
the power supply.
1.Take the hanging
board as a reference
and draw the
position on the
ceiling. It is
suggested to draw
the position with a
pen and then make
holes.
2.Knock the
expanded rubber
plug into the hole
of the wall
3.Align the expansion
rubber plug with
self-tapping screw, twist
it in clockwise, fix the
hanging plate, and align
the nut with the screw to
fix the wall plate
4.Hang the main
body as shown in
the figure, and the
main line of the
lamp body is
connected with
the zero line fire
line at home
3.Fixed ceiling site.
4.Replace the
lampshade to complete
the installation.
Cleaning (please clean and inspect lamps once every 6 months)
The power supply must be disconnected before cleaning, and the related operations must be
carried out after the lamps are completely cooled!
Wipe it gently with a soft dry cotton cloth instead of a wet cloth or other volatile liquids
when cleaning the lamp body ;
Please use a clean feather duster to gently brush the surface of the lampshade when
cleaning the PVC lampshade, so as not to stain the lampshade or cause deformation.
Expansion
rubber plug
Home wire
Connection
Expansion rubber plug
Self-tapping
screw
Top suction plate
Fastener for fixing lamp body
Acrylic lampshade
Self-tapping screw
Installation method of circular ceiling lamp
Installation method of square ceiling lamp
Electric wire of
lamp body
Page 2
Warranty regulations
We provide 2-year free warranty for the lamps sold. Customers with problems please
contact our after-sales customer service, and we will choose the corresponding method
according to the actual situation.
The warranty does not include light sources. You cannot enjoy free warranty in the
following cases:
Improper installation or abnormal use and unauthorized modification cause damage to
the lamp body;
Damage to lamps caused by external forces such as falls, impacts, earthquakes, floods,
public hazards, humidity, chemical corrosion, or natural disasters;
The lamps are damaged due to overcurrent and overvoltage caused by abnormal power
supply in the buyer's building;
Other damages not caused by the product itself.
Warranty Card
Product name:
Date of manufacture: MM-DDD-YYY Warranty with this card
Implementation criteria:
The following shall be completed by the dealer:
Sales date: MM-DDD-YYYY Tel.:
Distribution unit:
Address:
Date
Maintenance record
Handler
Product User Manual
All rights reserved. No reprint allowed
Loading...