Page 1
Assembly Instruction
CAUTION: Read instruction carefully and turn electricity off at main circuit breaker panel
before beginning installation.
Care and Cleaning
To clean the outside of the fixture, use a dry or slightly dampened clean cloth(use clean water, never
a solvent) to wipe the surface of the fixture.
To clear the inside of the fixture, first disconnect power to the fixture by turning off the circuit breaker
or by removing the fuse at the fuse box. Next, use a dry or slightly dampened clean cloth(use clean
water, never a solvent) to wipe the interior surface of the fixture
Do not use any cleaners with chemical, solvents or harsh abrasives. Use Only a dry soft cloth to dust
or wipe carefully.
Estimated Assembly Time:30 minutes
Part List and Hardware List
PIECE DESCRIPTION PICTURE QUANTITY PIECE DESCRIPTION PICTURE QUANTITY
A Lamp Body 1X H Canopy 1X
B Bulb 6X I Mounting Plate 1X
C Fixture Loop 1X J
Mounting
Screw
2X
D Closable Link 5X K Wire Nut 3X
E Chain 1X L Loop Assembly 1X
F Canopy Nut 1X M Connecting Rod 3X
G Hanging Loop 1X
1/3
Page 2
Installation
Step 1
Unpack all parts from cartons carefully.
Place the Canopy(H)onto the Hanging Loop(G)
Place the tube of Mounting Plate(I)into the theaded portion
of the Hanging Loop(G) and fix it by turing the Canopy
Nut(F) clockwise till tight.
Attach the Closable Link(D) onto the Hanging Loop(G)
Step 2
Thread Fixture Loop (C) to Loop
Assembly (L).
Attach the Closable Link(D) onto the
Fixture Loop (C)
Respectively attach the Closable
Link(D) onto the loop of the Loop
Assembly (L) and Connecting Rod (M)，
then respectively attach clip of the Loop
Assembly (L) to ring of the Lamp Body
(A).
Step 3 Wire connection
Connect,Hot,Black or Red outlet Supply W ire to: Connect,Neutral,White Outlet Supply Wire to:
Black White
*Parallel Cord(round&smooth) *Parallel Cord(square&ridged)
Clear,Brown,Gold or Black without Tracer(colored stripes) Clear,Brwn,Gold or Black without Tracer(colored stripes)
Insulated Wire(not green)with copper metal conductor Insulated Wire(not green)with Silver metal conductor
2/3
Page 3
*Note: When parallel wire(SPTI&SPTII)is used. The neutral wire is square shaped and
ridged and the hot wire will be round in shape and smooth.(See illustration on left)
Grounding Instructions:
a) For installation in the United States: Wrap ground wire from outlet box around green ground screw on
mounting bracket, no less than 2" from wire end. Tighten ground screw. If fixture is supplied with a ground wire,
connect to outlet ground wire with a wire connector.
b) For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around green grounding
screw on mounting bracket. Tighten ground screw.
Step 4
Install the Mounting Plate(I) to the junction box with
Mounting Screw (J)
Seperate the Mounting Plate(I) from the Canopy(H)
by turning the Canopy Nut(F) anti-clockwise.
Step 5
Attach the Canopy(H) to the junction box and fix it by
turning the Canopy Nut(F) clockwise
Insert the bulbs (B) into the Sockets
PLEASE USE TYPE"B" BULB MAX 40-WATT OR
CFL BULB MAX 13-WATT OR LED BULB MAX 9WATT
THERE ARE 6PCS LED 4-WATT BULB IN THE BOX
Step 6
Consult a qualified electrician to ensure correct
branch circuit conductor.
ENJOY YOUR LAMP
3/3
Loading...