Page 1
Installation Guide
Pleasego to our website for product cleaning tips. Go to the selection.
ToolsRequired: Flathead screwdriver, Phillips screwdriver,pliers, wire cutters, wire strippers,electrical tape, safety glasses.
LightSource:
FixtureHanging Height:
EstimatedAssembly Time:
Preparation:
present.If any parts are missingor damaged, do not attemptto assemble, install, or operatethe fixture. Contact your originalplace of purchase.
(4)A19 MediumBase100W bulb Maximum, bulb notincluded.
MinimumHanging Height is 16.5”, MaximumHanging Height is 52.5”.
30-45minutes
Identifyand inspect all parts beforebeginning installation. Check package contentlist and diagrams below toensure all parts are
Care+ Maintenance
Note: This CONVERTIBLE fixture can be mounted as pendant light or semi-flush light. Refer to respective
installation steps for installations.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
Crossbar Assembly
A
x1
6” Rod
B
x2
E
Ceiling Canopy
D
x1
Swivel
x1
STEP 2A - Installing the CrossbarAssembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw facing you. Secure the
Crossbar Assembly (A) with Outlet Box Screws (not included).
Tighten until snug.
Outlet Box
12” Rod
C
x2
Allen Wrench
G
x1
Assembly Instructions for Pendant Light
(Step 1A - Step 6A)
STEP 1A - Install Ceiling Canopy, Rods
and Fixture Body together
A. Thread the Swivel (E) onto the Ceiling
Canopy (D), Hand tighten until snug.
Tighten the set screw on the swivel (E)
by using theAllen Wrench (G).
B. Determine the Rods (B/C) to be
assembled to the Fixture Body (F)
according to your hanging height.
C. Pass the supply wires and ground wire
through the chosen rods (B/C) and the
Ceiling Canopy (D). Thread the Fixture
Body (F), the chosen
Rods (B/C) and the
Ceiling Canopy (D)
together. Hand tighten
until snug.
Suggested rods for
Ceiling height :
8’ ceiling : use (1) 6”
rods and (1) 12” rods
9’ ceiling : use (1) 6”
rods and (2) 12” rods
Supply
Wires and
Ground Wire
F
Fixture Body
F
x1
Figure 1A
G
Set Screw
A
Outlet Box Screws
(not included)
Figure 2A
STEP 3A Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
Remove mounting balls from the Crossbar Assembly (A). Fit the
D
E
B
B
C
C
Fixture Canopy
mounting balls. Note: The should be snug against
the and the mounting balls. If
ceiling
nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Fixture Canopy is secure, remove the mounting
ball and Fixture Canopy and proceed to Step 4A.
Mounting Screw
Fixture Canopy
to the
A
Mounting Ball
Crossbar Assembly (A) and secure with
Fixture Canopy
Supply Wires with
Ground Wire
not, adjust the length of the
Hex Nut and
Lock Washer
Figure 3A
1of2
Page 2
STEP 4A - Wire Connections
Wrap bare or green ground wire around green ground screw on the
A.
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Assembly Instructions for Semi-Flush Light
(Step 1B)
The following parts will not be used in the assembly of the SemiFlush Light fixture. Please set aside these parts.
B
6” Rod
x2
C
12” Rod
x2
(Extra Parts include)
White wire
from outlet box
Black wire from
outlet box (or Red)
Bare, or Green
Ground wire
from outlet box
Green Ground Screw
on the Crossbar
STEP 5A Install the Fixture-
A. Carefully tuck all wires into the outlet box and position the Fixture
Canopy over the outlet box.Align the holes in the ceiling canopy
with the mounting screws, then attach the Fixture Canopy using the
previously removed mounting balls. Hand tighten until snug.
A
Fixture Canopy
White wire
from fixture
Black wire
from fixture
Ground wire
from Fixture
Figure 4A
Mounting Screw
STEP 1B Install Ceiling Canopy to Socket Assembly
A. Pass the supply wires with the ground wire through the swivel (if
B. Go to Step 2A Step 6A to complete installations.-
-
used) and the ceiling canopy (D). Thread the swivel (if used) and the
ceiling canopy (D) onto the Fixture Body (F). Hand tighten until snug.
Cut the wires leaving approximately 6” of wire extending from the
ceiling canopy.
: Always tighten the set screw on the swivel (D) by using the
NOTE
Allen Wrench (G) if used.
G
Set Screw
Figure 1B
D
Optional Swivel
Supply Wires
and Ground Wire
F
Mounting Ball
Figure 5A
STEP 6A - Install the Bulbs
A. Insert bulbs onto sockets and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
Socket
Vintage Bulb
(recommended
but not included)
Figure 6A
2of2
Loading...