Ivy Bronx W001650530 Owner Manual

Description

Caution : You must read this before you proceed

Left Armchair

Label Picture

A2 Seat 1

Right Leg(with

B2

C2

Pre-installed

Leveler)

Left

Armrest/Leg(with

Pre-installed

Leveler)

QTY

1

1

D Seat Cushion 1

E Back Cushion 1

Page 1 OF 5

Label Picture Description QTY

① Bolt (M6*40MM) 6
② Bolt (M6*32MM) 2
③ Washer 8

④ Allen Key 1

Before

Beginnin

g

Assembly

:

Overview

Left Armrest/Leg(C2)

Seat(A2)

*6

*2

*8

Back Cushion(E)

Right Leg(B2)

Seat Cushion(D)

FRONT FACING

This Left Armchair has multiple parts and may require up to 30 minutes to assemble. To
give you an overview of the Left Armchair parts, the above picture is to help you put the
various parts into perspective. Please read through the instructions below to familiarise
yourself with the parts and steps before assembly.

Page 2 OF 5

Step 1

Step 1.1

Step 1.2

Open the carton and place all the parts onto a clean, non-marring surface.
Place the Left Armrest/Leg(C2) facedown.

1.1) Align Seat(A2) to Left Armrest/Leg(C2) as shown above.

1.2) Attach Seat(A2) to Left Armrest/Leg(C2) using Bolts(①), and Washers(③) with Allen

Key(④) as shown above.
Attach Seat(A2) to Left Armrest/Leg(C2) using Bolt(②), and Washer(③) with Allen Key(④)
as shown above.

Tighten the Bolts fully in a sequential manner.

Step 2

Step 2.2

Step 2.1

2.1) Align Seat(A2) to Right Leg(B2) as shown above.

2.2) Attach Seat(A2) to Right Leg(B2) using Bolts(①)and Washers(③) with Allen Key(④)

as shown above.
Attach Seat(A2) to Right Leg(B2) using Bolt(②) and Washer(③) with Allen Key(④) as
shown above

Tighten the Bolts fully in a sequential manner.

Page 3 OF 5

Step 3

Then, with the assistance from an adult partner, stand the Chair upright.
Adjust the Pre-installed Levellers until the Chair is level with the ground.
To adjust the Levellers, with assistance from an adult partner, tilt the Chair to rest on two
feet.
Adjust the levellers to the desired height until the Chair is level.

Step 4

Place the Seat Cushion(D) on the Seat(A2).
Tie the rope to the Seat(A2).

Step 5

Place the Back Cushion(E) on the Left Armchair.
Your Left Armchair is ready for use.

This Left Armchair can only be used on a flat, level surface.

Page 4 OF 5

Page 5 OF 5

Description

Caution : You must read this before you proceed

Right Armchair

Label Picture

A1 Seat 1

RightArmrest/Leg(

B1

C1

with Pre-installed

Leveler)

Left Leg(with Pre-

installed Leveler)

QTY

1

1

D Seat Cushion 1

E Back Cushion 1

Page 1 OF 5

Label Picture Description QTY

① Bolt (M6*40MM) 6
② Bolt (M6*32MM) 2
③ Washer 8

④ Allen Key 1

Before

Beginnin

g

Assembly

:

Overview

Back Cushion(E)

Left Leg(C1)

*6

*2

*8

RightArmrest/Leg(B1)

Seat(A1)

Seat Cushion(D)

FRONT FACING

This Right Armchair has multiple parts and may require up to 30 minutes to assemble. To
give you an overview of the Right Armchair parts, the above picture is to help you put the
various parts into perspective. Please read through the instructions below to familiarise
yourself with the parts and steps before assembly.

Page 2 OF 5

Step 1

Step 1.1

Open the carton and place all the parts onto a clean, non-marring surface.
Place the Right Armrest/Leg(C1) facedown.

1.1) Align Seat(A1) to Right Armrest/Leg(C1) as shown above.

1.2) Attach Seat(A1) to Right Armrest/Leg(C1) using Bolts(①), and Washers(③) with Allen

Key(④) as shown above.
Attach Seat(A1) to Right Armrest/Leg(C1) using Bolt(②), and Washer(③) with Allen
Key(④) as shown above.

Tighten the Bolts fully in a sequential manner.

Step 1.2

Step 2

Step 2.1

Step 2.2

2.1) Align Seat(A1) to Left Leg(B1) as shown above.

2.2) Attach Seat(A1) to Left Leg(B1) using Bolts(①)and Washers(③) with Allen Key(④) as

shown above.
Attach Seat(A1) to Left Leg(B1) using Bolt(②) and Washer(③) with Allen Key(④) as
shown above

Tighten the Bolts fully in a sequential manner.

Page 3 OF 5

Step 3

Then, with the assistance from an adult partner, stand the Chair upright.
Adjust the Pre-installed Levellers until the Chair is level with the ground.
To adjust the Levellers, with assistance from an adult partner, tilt the Chair to rest on two
feet.
Adjust the levellers to the desired height until the Chair is level.

Step 4

Place the Seat Cushion(D) on the Seat(A1).
Tie the rope to the Seat(A1).

Step 5

Place the Back Cushion(E) on the Right Armchair.
Your Right Armchair is ready for use.

This Right Armchair can only be used on a flat, level surface.

Page 4 OF 5

Page 5 OF 5

Description

Caution : You must read this before you proceed

Armless Chair

Label Picture

A3 Seat 1

Right Leg(with

B3

C3

Pre-installed

Leveler)

Left Leg(with Pre-

installed Leveler)

QTY

1

1

D Seat Cushion 1

E Back Cushion 1

Page 1 OF 5

Label Picture Description QTY

① Bolt (M6*40MM) 7
② Washer 7

③ Allen Key 1

Before

Beginnin

g

Assembly

:

Overview

Seat Cushion(D)

*7

*7

Back Cushion(E)

Seat(A3)

Right Leg(B3)

Left Leg(C3)

FRONT FACING

This Armless Chair has multiple parts and may require up to 30 minutes to assemble. To
give you an overview of the Armless Chair parts, the above picture is to help you put the
various parts into perspective. Please read through the instructions below to familiarise
yourself with the parts and steps before assembly.

Page 2 OF 5

Step 1

Step 1.1

Step 1.2

Open the carton and place all the parts onto a clean, non-marring surface.
Place the Right Leg(B3) facedown as shown above.

1.1) Align Seat(A3) to Right Leg(B3) as shown above.

1.2) Attach Seat(A3) to Right Leg(B3) using Bolts(①) and Washers(②) with Allen Key(③)

as shown above

Tighten the Bolts fully in a sequential manner.

Step 2

Step 2.1

Step 2.2

2.1) Align Seat(A3) to Left Leg(C3) as shown above.

2.2) Attach Seat(A3) to Left Leg(C3) using Bolts(①) and Washers(②) with Allen Key(③)

as shown above

Tighten the Bolts fully in a sequential manner.

Page 3 OF 5

Step 3

Then, with the assistance from an adult partner, stand the Chair upright.
Adjust the Pre-installed Levellers until the Chair is level with the ground.
To adjust the Levellers, with assistance from an adult partner, tilt the Chair to rest on two
feet.
Adjust the levellers to the desired height until the Chair is level.

Step 4

Place the Seat Cushion(D) on the Seat(A3).
Tie the rope to the Seat(A3).

Step 5

E

Place the Back Cushion(E) on the Armless Chair.
Your Armless Chair is ready for use.

This Armless Chair can only be used on a flat, level surface.

Page 4 OF 5

Page 5 OF 5

Caution : You must read this before you proceed

Ottoman

Label Picture Description QTY

A9 Seat Panel 1

B9

K Seat Cushion 1

Leg with Pre-

2

installed Leveler

L

Anti-Slip Mat

1

Page 1 OF 5

Label Picture Description QTY

① Bolt (M6*30MM) 5

② Bolt (M6*25MM) 5

③ Allen Key 1

Before

Beginnin

g

Assembly

*5*5

Overview

Seat Cushion(K)

Seat Panel(A9)

Leg(B9)

FRONT FACING

This Ottoman has multiple parts and may require up to 30 minutes to assemble. To give
you an overview of the Ottoman parts, the above picture is to help you put the various
parts into perspective. Please read through the instructions below to familiarise yourself
with the parts and steps before assembly.

Page 2 OF 5

Step 1

Step 1.1

Open the carton and place all the parts onto a clean, non-marring surface.

1.1) Insert Seat Panel(A9) into Leg(B9) as shown above

1.2) Attach Seat Panel(A9) to Leg(B9) using Bolts(①) with Allen Key(③) as shown above.

1.3) Attach Seat Panel(A9) to Leg(B9) using Bolts(②) with Allen Key(③) as shown above.
Tighten the Bolts fully in a sequential manner.

Step 1.2

Step 1.3

Step 2

Step 2.1

2.1) Insert Seat Panel(A9) into Leg(B9) as shown above

2.2) Attach Seat Panel(A9) to Leg(B9) using Bolts(①) with Allen Key(③) as shown above.

2.3) Attach Seat Panel(A9) to Leg(B9) using Bolts(②) with Allen Key(③) as shown above.
Tighten the Bolts fully in a sequential manner.

Step 2.2

Step 2.3

Page 3 OF 5

Step 3

Then, with the assistance from an adult partner, stand the Ottoman upright.
Adjust the Pre-installed Levellers until the Ottoman is level with the ground.
To adjust the Levellers, with assistance from an adult partner, tilt the Ottoman to rest on
two feet.
Adjust the levellers to the desired height until the Ottoman is level.

Step 4

Step4.1

Step4.1 Place the Anti-Slip Mat(L) on the Ottoman.
Step4.2 Place the Seat Cushion(K) on the Ottoman.

Step 5

Step4.2

Your Ottoman is ready for use.

This Ottoman can only be used on a flat, level surface.

Page 4 OF 5

Page 5 OF 5

Caution : You must read this before you proceed

Table

Label Picture Description QTY

A8 Table Top 1

B8

Label Picture Description QTY

① Bolt (M6*30MM) 5

Leg with Pre-

2

installed Leveler

② Bolt (M6*25MM) 5
③ Allen Key 1

Page 1 OF 4

Before

Beginnin

g

Overview

Leg(B8)

*5

Table Top(A8)

*5

FRONT FACING

This Table has multiple parts and may require up to 30 minutes to assemble. To give you
an overview of the Table parts, the above picture is to help you put the various parts into
perspective. Please read through the instructions below to familiarise yourself with the
parts and steps before assembly.

Step 1

Step 1.1

Step 1.2

Step 1.3

Open the carton and place all the parts onto a clean, non-marring surface.

1.1) Align Table Top(A8) to Leg(B8) as shown above.

1.2) Attach Table Top(A8) to Leg(B8) using Bolts(①) with Allen Key(③) as shown above.

1.3) Attach Table Top(A8) to Leg(B8) using Bolts(②) with Allen Key(③) as shown above.
Tighten the Bolts fully in a sequential manner.

Page 2 OF 4

Step 2

Step 2.1

Step 2.2

2.1) Align Table Top(A8) to Leg(B8) as shown above.

2.2) Attach Table Top(A8) to Leg(B8) using Bolts(①) with Allen Key(③) as shown above.

2.3) Attach Table Top(A8) to Leg(B8) using Bolts(②) with Allen Key(③) as shown above.
Tighten the Bolts fully in a sequential manner.

Step 2.3

Step 3

Then, with the assistance from an adult partner, stand the Table upright.
Adjust the Pre-installed Levellers until the Table is level with the ground.
To adjust the Levellers, with assistance from an adult partner, tilt the Table to rest on two
feet.
Adjust the levellers to the desired height until the Table is level.

Step 4

Your Table is ready for use.

This Table can only be used on a flat, level surface.

Page 3 OF 4

Page 4 OF 4