Page 1
Assembly Instructions
Please look underneath the seat panel for hardware packs
Caution: You must read this before you proceed
Chair
Page 1 OF 7
Page 2
Parts List
Label Picture
A
B
C
D
E
Description
Backrest Panel 1
Seat Panel 1
Short Leg 2
Long Right Leg 1
Long Left Leg 1
QTY
F
Hardware
Label Picture
1
2
3
4
5
Seat Cushion 1
Description
Bolt (M6x )
Bolt (M6x )
Spring Washer
(6.5/11x2mm)
Washer
Allen Key
40 mm
60 mm
(6.5/16x2mm)
QTY
5
9
9
9
1
Page 2 OF 7
Page 3
Assembly Preparation
...
.
Save all packaging until finished
Assemble on a clean non-marring surface (packing foam)-
Do not assemble on flooring or carpet-
Have 2 adults on hand for assembly-
.
Read instructions, cover to cover-
Before Beginning Assembly:
Assembly Steps
OVERVIEW
Long Right Leg (D)
Backrest Panel (A)
Seat Cushion (F)
Seat Panel (B)
Long Left Leg (E)
This Chair has multiple parts and may require up to 30 minutes to
assemble. To give you an overview of the Chair parts, the above picture is
Short Leg (C)
FRONT FACING
to help you put the various parts into perspective. Please read through the
instructions below to familiarise yourself with the parts and steps before
assembly.
Page 2 OF 7
Page 4
Step 1
Unpack and place all parts on a clean, non-marring surface.
Step 2
Wooden Dowel
A
5
1
D
With assistance from your adult partner, insert Wooden Dowel on Backrest
Panel(A) into the mortise of Long Right Leg(D).
Attach Long Right Leg(D) to Backrest Panel(A) using Bolts(①) with Allen
Key(⑤).
Do not fully tighten the Bolts.
Repeat the same process with the remaining Long Left Leg(E).
Page 3 OF 7
Page 5
Step 3
A
B
5
2
3
4
D
E
With assistance from your adult partner, put Seat Panel(B) onto Backrest
Panel(A) with Long Right Leg(D) and Long Left Leg(E) in the direction of the
arrow as shown in above picture.
Attach Seat Panel(B) to Long Right Leg(D) and Long Left Leg(E) using
Bolts(②), Spring Washers(③), and Washers(④) with Allen Key(⑤).
Do not fully tighten the Bolts.
Step 4
C
B
4
2
3
5
Attach Short Legs (C) to Seat Panel(B) using Bolts(②), Spring
Washers(③), and Washer(④) with Allen Key(⑤).
Do not fully tighten the Bolts.
Page 4 OF 7
Page 6
Stand the Chair up, with assistance from your adult partner.
Exert pressure floorwards, onto the Chair with both your hands.
This pressure will help the Legs and Chair reach full alignment status.
Check for wobbles on a LEVEL surface.
If no wobbles are found proceed to tighten the Bolts in a sequential
manner, until evenly secured.
When tightening the Bolts tighten sequentially.
Do not tighten any Bolt fully and then move on towards the next one.
If there are still wobbles, loosen the Bolts and excute the same above
process.
If the Chair is not Stable it could lead to damage to the product.
Step 5
F
Put Seat Cushion(F) onto the Chair.
Tie the velcro straps of Seat Cushion(F) to the slats of Seat Panel(B).
Your Chair is ready for use.
This Chair can only be only be used on a flat, lever surface.
Page 5 OF 7
Page 7
Care & Maintenance
Do not put hot items directly on furniture surface
Do not clean furniture with harsh cleansers or polish.
To obtain the longest lifespan of your outdoor prodcts, minimizing exposure to direct
sunlight is recommended.
Children should not climb or jump on the furniture.
Do not write on furniture without a padded barrier to protect the surface.
To obtain the longest lifespan of your outdoor products, avoid extended and
lengthy exposure to rain, snow, and direct sunshine. Whenever possible cover
the product and /or place under patio or awnings.
Not for commercial use. For residential use only .
Stains may be removed with mild soap solution and damp cloth.
Dust and pick-up spills using a clean, non-colored, lint-free cloth .
Page 6 OF 7
Loading...