Page 1
In addition to installing the restraints, to help prevent tip-over:
1. Place heaviest items in the lowest drawers,
2. Unless specifically designed to accommodate, do not set TV’s
or other heavy objects on top of this product,
3. Never allow children to climb or hang on drawers, doors, or
shelves,
4. Do no leave drawers open,
5. Never open more than one drawer at a time, and
6. Do not step on the base.
Caution : You must read this before you proceed
Table
Picture
Label Picture Description QTY
A Table Top 1
Page 1 OF 8
Page 2
B Leg 2
(
)
(
)
Label Picture Description QTY
①
②
Table Restraint Device Hardware
③
④
⑤
⑥
⑦
⑧
Bolt 9
Allen Key 1
Metal Bracket 4
Wall Plug 2
Wall Plug
Screw
Screw(M6*50mm) 2
Restraint Strap 2
M6*80mm
Screwdriver
not provided
2
1
Power Drill
⑨
⑩
Before Beginning
Assembly:
(not provided)
Hammer
(not provided)
Page 2 OF 8
1
1
Page 3
x9pcs
x4pcs
x2pcs
Overview
x2pcs
x2pcs
x2pcs
x1pc
This Table has multiple parts and may require up to some 30 minutes
to assemble. To give you an overview of the Table parts, the above
picture is to help you put the various parts into perspective. Please
read through the instructions herebelow to familiarise yourself with the
parts and steps before assembly.
Page 3 OF 8
Page 4
Step 1
②
Unpack and place all parts on a clean, non-marring surface.with the
help of your adult partner.
Step 2
②
①
B
A
①
Insert the Leg into the leg position in the Table Top(A).
Attach the Leg(B) to the Table Top(A) using Bolt(①) , with Alley
Key(②).
Only Loosely Tighten the Bolts at this stage.
Repet this process with the remaining Legs.
Page 4 OF 8
Page 5
Step 3
With the help of your adult partner, carefully stand the Table up.
Place your Table on a level surface, to check for wobbles.
If there is a wobble, press the Table softly downwards with your hands
to make the Table level. Then turn the Table over with the help of your
adult partner, and tighten all Bolts completely.
If it isn't a wobble, turn the Table over with the help of your adult
partner, and tighten all Bolts compelely.
For your safety , suggest to install the following steps.
Step 4
⑧
⑥
③
4.1) Turn the Table on the back side faces you.
A
4.2) Attach Metal Brackets(③) to Back Table(A), where labeled, using
Screw(⑥) with Screwdriver(⑧).
Page 5 OF 8
Page 6
Step 5
Step5.1
④
Step5.2
⑩
⑨
WALL
5.1) Drill two holes on wall at same height as Metal Brackets(③) on
Table back with Power Drill(⑨).
You can mark these points in two ways as below:
1) Move the Table back to the wall. Mark two points the same
height as the Table on the wall.
Note: The Metal Brackets(③)need to be secured to a solid, load
bearing surface. Please use a Stud Finder(not supplied) if needed to
locate the Wall Frame.
2) Measure the height of the Metal Brackets(③) with ruler/measuring
tape and mark on wall to keep them accurate and the same height.
Page 6 OF 8
Page 7
y
(
)
Step 6
⑤
⑧
③
④
Attach Metal Brackets(③) to Wall Plugs(④) using Wall Plug
Screws(⑤) with Screwdriver(⑧).
WALL
Step 7
⑦
③
③
WALL
Move the Table back against wall.
Pull the Restraint Straps(⑦) through the Metal Brackets(③) on the
wall
and Table one b
one, and pull the Restraint Straps
⑦
tight.
Page 7 OF 8
Page 8
Step 8
Your Table is ready for use.
This Table can only be used on a flat, level surface.
Do not put hot items directly on furniture surface
Do not clean furniture with harsh cleansers or polish.
Do not place furniture under direct sunlight.
Do not place furniture near heating or cooling vents.
Do not write on furniture without a padded barrier to protect the surface.
Do not place furniture outside . For indoor use only .
Not for commercial use. For residential use only .
Stains may be removed with mild soap solution and damp cloth.
Children should not climb or jump on the furniture.
Dust and pick-up spills using a clean, non-colored, lint-free cloth .
Page 8 OF 8
Loading...