ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed.
However, the installation instructions do apply to this product.
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJ ON CTEUR.
ASSEMBLING THE FIXTURE (Fig.2)
1. Shut off the power at the circuit breaker box. Remove old fixture and all hardware
2. Slide the electrical wires through the tube(F)/(E)/(D)/(C)/(B)/(A)/ring/canopy and
3. Raise the tube(F) to the center pipe thread of the lamp body(G), raise the
HANGING THE FIXTURE (Fig.1 Please see the Page.2)
IMPORTANT: For a safe and secure installation, this fixture must be installed by
means of support that is independent of the junction box.
4. Provide a 1/4” IPS pipe screw with one end securely mounted to a beam or a
5. Assemble the hex nuts, lock washer, hex coupling(the end of assembled fixture
6. IMPORTANT: you must, run the safety cable through the two clamp bolts,
7. Connect the electrical wires as Shown in Fig.3, making sure that all wire nuts are
8. Install the light bulbs(Not included) in accordance with the fixture specifications.
9. Raise the end screw of the garnish cluster(A)/(B)/(C) and(D) insert to the screw hole
Your installation is now complete. Return power to the junction box
and test the fixture.
from Junction Box. Carefully unpack your new fixture and lay out all the parts on a
clear area. Take care not to lose any small parts necessary for installation.
assembled ceiling loop. By measuring, determine correct tube length needed for
proper hanging height. Note: The electrical wires and safety cable each through to
the side coupling hole of the assembled ceiling loop.
tube(E)/(D)/(C)/(B)/(A) and assembled ceiling loop to the screw pipe nipple in o rder,
then by turning it clockwise until tight.
structural member. The other end should protrude through the center of the junction
box as shown. The junction box is not included.
body) to center 1/4”IPS support pipe and adjust overall length to allow the lock ring
to hold the canopy flush to the ceiling. When the adjustments have been completed,
secure the three (3) hex nuts until tight, as shown.
then through the top of the junction box and secure to structural member.
NOW, fasten the end of safety cable through the two clamp bolts(see fig.1),
lock them securely with the four small hex nuts until tight.
secured. You may have to wrap the connections with electrical t ape. If your Junction
Box has a ground wire (green or bare copper), connect the fixture ground wire to it.
Otherwise connect fixture’s ground wire directly to the assembled ceiling loop’s
coupling with the screw provided. After wires are connected, tuck them carefully
inside the Junction Box. Slide the canopy onto the Junction box, lock it securely with
the ring until tight.
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
of lamp body(G), by turn it clockwise until tight. Note: the garnish cluster(D2+C2),
(A4+B4),(C4+D4),(B6+A6),(D4+C4),(A4+B4) and(C2+D2) must evenly spaced
distribution on the every lap.
FIG.2
D0.6"x6"x1PC
D0.6"x12"x1PC
D0.6"x18"x4PCS
A:4PCS
C:4PCS
B:6PCS
D:4PCS
C:2PCS
FIG.2
FIXTURE
WIRES
BLACK
D:2PCS
HOUSE
WIRES
Black
(Hot)
B:4PCS
D:4PCS
A:6PCS
C:4PCS
C:4PCS
B:6PCS
D:4PCS
A:4PCS
FIXTURE
WIRES
WHITE
(Neutral)
AssembledEffect
GL
A:4PCS
C:2PCS
HOUSE
WIRES
White
C:2PCS
D:2PCS
FIXTURE
WIRES
GREEN
Thread
(Ground)
Green or
Copper(Ground)
GL
GL
GL
GL
D:12PCS
B:4PCS
D:4PCS
A:6PCS
C:4PCS
B:4PCS
HOUSE
WIRES
Bare
Thank you for purchasing our product.
Need assistance with parts or assembly? Please call customer service
ALL RIGHTS RESERVED. Page 1 of 2
Loading...