Page 1
Label Picture Description QTY
A Seat 1
B Left Leg 1
C Right Leg 1
Assembly Instructions
Caution : You must read this before you proceed
BARSTOOL
Part List
Page 1 OF 5
Page 2
D Front Foot Rest 1
E Back Foot Rest 1
F Seat Cushion 1
Label Picture Description QTY
① Bolt(M6*20MM) 13
② Washer 13
③ Allen Key 1
④
PE Cap 9
Hardware
Assembly Preparation
Before Beginning
Assembly:
Page 2 OF 5
Page 3
Assembly Steps
Overview
This Barstool has multiple parts and may require up to 30 minutes to assemble. To give
you an overview of the Barstool parts, the above picture is to help you put the various
parts into perspective. Please read through the instructions below to familiarise yourself
with the parts and steps before assembly.
Step 1
Open the carton and place all the parts onto a clean, non-marring surface.
Attach Left Leg(B) and Right Leg(C) to Seat(A) using Bolts(①) and Washers(②) with
Allen Key(③) as pictured.
Do not fully tighten the Bolts.
Occasionally some of the PE Wicker shifts and covers the mounting positions
preventing easy assembly. The PE Wicker should never be cut, but moved away
from the mounting positions.
Back Foot Rest(E)
Page 3 OF 5
Page 4
Step 2
Place the Front Foot Rest(D) and Back Foot Rest(E) between the Left Leg(B) and Right
Leg(C).
Attach Front Foot Rest(D) and Back Foot Rest(E) to Left Leg(B) and Right Leg(C) using
Bolts(①) and Washers(②) with Allen Key(③) as shown in the picture.
Tighten all Bolts at all joints sequentially.
DO NOT tighten any Bolt fully and then move onto the next one. This may cause
the frame to warp.
Step 3
Place the Barstool on a LEVEL SURFACE to check for wobbles. If it wobbles, lift the
Barstool some 30cm to 50cm high from the ground. Keep your feet and toes well away
from the drop zone. Drop the Barstool freely and vertically with all four legs, hitting the
ground, at the sametime. This Drop Test will help to ensure that all the Bolts and gaps
reach full alignment status. Test again for evenness on a LEVEL SURFACE. If no
wobbles are found, slowly and steadily, place the Barstool facedown.Then, proceed to
tighten all Bolts in a sequential manner.When tightening the Bolts, tighten sequentially.
DO NOT tighten any Bolt fully and then move on towards the next one.This could cause
the frame to warp. If there are still wobbles, loosen the Bolts andexecute the same drop
test.
If the Barstool is not stable, it could lead to damage to the product.
Page 4 OF 5
Page 5
Step 5
Put the Seat Cushion(F) on the Barstool.
Your Barstool is ready for use.
This Barstool can only be used on the flat, level surface.
Step 4
Put the PE Cap (④ ) on the screw,as the picture above.
Do not clean furniture with harsh cleansers or polish.
Do not put hot items directly on furniture surface
Do not write on furniture without a padded barrier to protect the surface.
To obtain the longest lifespan of your outdoor products, avoid extended and
lengthy exposure to rain, snow, and direct sunshine. Whenever possible cover the
product and /or place under patio or awnings.
To obtain the longest lifespan of your outdoor prodcts, minimizing exposure to direct
sunlight is recommended.
Not for commercial use. For residential use only .
Stains may be removed with mild soap solution and damp cloth.
Dust and pick-up spills using a clean, non-colored, lint-free cloth .
Children should not climb or jump on the furniture.
Keep away from sources of ignition.
Page 5 OF 5
Loading...