iView Technology HL-104 User Manual

Download

HL-104 User Manual V0.6(M02)

HL-104

─ 4CH DVR ─

User Manual

HL-104 v0.6(M02)

This document contains preliminary information and subject to change without notice.

HL-104 User Manual V0.6(M02)

This symbol is intended to alert the user to the presence

of unprotected “Dangerous

voltage" within the product's enclosure that may be strong enough to cause a risk of electric shock.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

NOTE: This equipment has been tested and found to comply with the limits for a class digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

HL-104 User Manual V0.6(M02)

Table of Contents

CHAPTER 1 PACKING DETAIL AND INSTALLATION _____________________ 5

1-1 PACKING ____________________________________________________ 5 1-2 Hard Disk Installation _________________________________________ 6

CHAPTER 2 PANEL LOCATION ________________________________________ 9

2-1 FRONT PANEL CONTROLS ____________________________________ 9 2-2 4CH REAR PANEL CONNECTORS _____________________________ 10

CHAPTER 3 LIVE, PLAYBACK AND PTZ OPERATIONS _________________ 11

3-1 LIVE Mode _________________________________________________ 11 3-2 PLAYBACK Mode ____________________________________________ 14 3-3 PTZ Mode __________________________________________________ 16

CHAPTER 4 MAIN MENU SETUP ____________________________________ 18

4-1 RECORD SETUP ____________________________________________ 19

4-1.1 Quality & Frame Rate Setup _____________________________ 21

4-2 EVENT SETUP ______________________________________________ 21

4-2.1 MOTION SETUP ________________________________________ 22

4-2.1.1 MOTION AREA SETUP______________________________ 23

4-2.2 SENSOR SETUP ________________________________________ 23

4-3 SCHEDULE SETUP __________________________________________ 24

4-3.1 Schedule Record Setup _________________________________ 25

4-3.2 Holiday Setup __________________________________________ 25 4-4 CAMERA SETUP ____________________________________________ 26 4-5 ACCOUNT SETUP ___________________________________________ 27

4-5.1 Permission Setup _______________________________________ 28

4-5.2 User Picture Setup _____________________________________ 28 4-6 NETWORKING SETUP ________________________________________ 29

4-6.1 NETWORKING SETUP ___________________________________ 29

4-6.1.1 DHCP ____________________________________________ 29 4-6.1.2 LAN ______________________________________________ 30

4-6.1.3 ADSL _____________________________________________ 30 4-6.2 HTTP Setup ____________________________________________ 31 4-6.3 DDNS Setup ___________________________________________ 31 4-6.4 Mail Setup _____________________________________________ 32

4-7 PTZ & RS485 SETUP ________________________________________ 33 4-8 SYSTEM SETUP _____________________________________________ 34

4-8.1 DISPLAY SETUP ________________________________________ 35 4-8.2 DATE/TIME SETUP ______________________________________ 35

4-8.2.1 CHANGE DATE & TIME _____________________________ 36

4-8.2.2 TIME ZONE AND DAYLIGHT SAVING TIME SETUP _____ 36

4-8.2.3 INTERNET TIME SETUP ____________________________ 37 4-8.3 BUZZER & RELAY SETUP _______________________________ 37 4-8.4 SPOT SETUP ___________________________________________ 38

4-9 UTILITY SETUP _____________________________________________ 39 4-10 DIAGNOSTIC _______________________________________________ 40

CHAPTER 5 BACKUP & SEARCH ____________________________________ 41

5-1 BACKUP SETUP _____________________________________________ 41 5-2 SEARCH SETUP _____________________________________________ 42

5-2.1 EVENT SEARCH ________________________________________ 43 5-2.2 TIME SEARCH __________________________________________ 44

HL-104 User Manual V0.6(M02)

CHAPTER 6 Rempte Software Installation and Setup ____________________ 45

6-1 AP Software Installation and instruction _______________________ 45 6-2 How to do remote monitoring through IE ______________________ 47 6-3 AP Software Operation _______________________________________ 48

CHAPTER 7 SPECIFICAITONS _______________________________________ 49 CHAPTER 8 MOBILE APPLICATION INSTALLATION AND USAGE __________ 51

8-1 Mobile Application Installation and Operation for Symbian System 51

8-1.1 Mobile Application Installation ____________________________ 51 8-1.2 Mobile Application Operation _____________________________ 52

8-1.2.1 Add New Login DVR _______________________________ 52

8-1.2.2 Logging Onto the DVR _____________________________ 52

8-1.2.3 Modify the Login Information of DVR ________________ 53

8-1.2.4 Delete the Login Information of DVR _________________ 53 8-1.3 Live Monitoring Operation _______________________________ 53

8-1.3.1 Scroll the Image ___________________________________ 54

8-1.3.2 Image Quality Setup _______________________________ 54

8-1.3.3 Channel Display ___________________________________ 54

8-1.3.4 Size of Image _____________________________________ 55

8-1.3.5 Rotate the image __________________________________ 55

8-1.3.6 Alarm ____________________________________________ 55

8-2 Mobile Application Installation and Operation for Windows Mobile Sy stem __________________________________________________________ 56

8-2.1 Mobile Application Installation ____________________________ 56 8-2.2 Mobile Application Operation _____________________________ 57 8-2.3 Operation under the LIVE monitoring. _____________________ 58

CHAPTER 9 CMS INSTALLATION AND USAGE GUIDE ___________________ 59

9-1 CMS Installation _____________________________________________ 59 9-2 CMS LOGIN AND ENVIRONMENT ______________________________ 62 9-3 DVRs, Groups & Events ______________________________________ 63

9-3.1 View DVR／Group List __________________________________ 63 9-3.2 View Event Logs _______________________________________ 64

9-4 Local PC Information and Control _____________________________ 64 9-5 Main Display ________________________________________________ 65

9-5.1 Audio Control __________________________________________ 65 9-5.2 eMAP Display __________________________________________ 66 9-5.3 PTZ Control ____________________________________________ 67

9-6 Operation Bar _______________________________________________ 68

9-6.1 User administration _____________________________________ 69 9-6.2 DVR Administration _____________________________________ 69 9-6.3 Group Administration ___________________________________ 70 9-6.4 eMap Administration ____________________________________ 71 9-6.5 Remote Play ___________________________________________ 72 9-6.6 HDD Playback __________________________________________ 73 9-6.7 File Playback ___________________________________________ 73 9-6.8 Event Playback _________________________________________ 74 9-6.9 Snapshot Data _________________________________________ 74 9-6.10 Recording Data ________________________________________ 75

APPENDIX I I-DVR.NET REGISTRATION _____________________________ 76 APPENDIX II Remote Monitoring IE ActiveX Control Installation Instruction ___ 78

HL-104 User Manual V0.6(M02)

CHAPTER 1 PACKING DETAIL AND INSTALLATION

1-1 PACKING

1. DVR

Note: Standard shipping products do not include HDD

3. IR Remote Control

7. Screws x4

4. Batteries x2

2. Quick Start

6. SATA Cord x1

8. Power Adaptor

5. CD

HL-104 User Manual V0.6(M02)

1-2 Hard Disk Installation

Step 1: Take off the three screws from the bottom of the DVR as indicated in red circles in

the picture below.

Step 2: Open the cover follow the way the arrows indicate.

Step 3: Fix the HDD to rack mount and connect SATA and the power cable as indi

cated.

HL-104 User Manual V0.6(M02)

Step 4: Put DVR bottom up, screw to fix the HDD as indicated.

Step 5: Put the cover back and put the three screws back to fix the cover in the bottom of

the DVR.

HL-104 User Manual V0.6(M02)

NOTE: The initialization of new-installed HDD is required before recording, please refer to manual “4-8UTILITY SETUP” for detail.

HL-104 User Manual V0.6(M02)

CHAPTER 2 PANEL LOCATION

2-1 FRONT PANEL CONTROLS

○

USB Port

Top(USB2.0) is used to plug the USB memory stick Bottom(USB1.1) is used to plug the mouse

○

LED Display- Power

DVR Power is on.

○

LED Display - HDD

Hard disk is in use.

○

LED Display - LAN

Connected to the internet.

○

LED Display- LOGIN

Remote user logged in.

○

LED Display - REC

DVR Recording. (or Schedule Recording and recording are on)

○

LED Display - PLAY

DVR Playing back.

○

IR Sensor

Input sensor for the remote control.

④

⑥

⑦

⑧

①

②

③

⑤

HL-104 User Manual V0.6(M02)

2-2 4CH REAR PANEL CONNECTORS

① ③ ④ ⑧

② ⑤ ⑥ ⑦ ⑨

① DC 12V

Socket for a DC 12V input.

② MAIN monitor

BNC port for the main monitor.

③ VIDEO IN

BNC input ports for cameras, 16 in total.

④ AUDIO IN

RCA input port for audio signal.

⑤ AUDIO OUT

RCA output for audio signal.

⑥ NTSC／PAL Switch

Switch between NTSC and PAL format.

⑦ LAN

Network port.

⑧ VGA

VGA port.

⑨ EXTERNAL I/O

EXTERNAL I/O port (not available on HL-104)

HL-104 User Manual V0.6(M02)

CHAPTER 3 LIVE, PLAYBACK AND PTZ OPERATIONS

The IR remote control and mouse operate differently under each mode; this chapter describes the functions of them under three different modes: LIVE, PLAYBACK and PTZ.

3-1 LIVE Mode

You can monitor all the channels, listen to audio signal and have some related operations under LIVE mode. This paragraph describes the IR remote control, mouse operation and on screen graphical icons under LIVE mode.

Table 3-1.1 Functions of remote control under LIVE mode

Button

Description

REC

Start/Stop recording.

PLAY

Start playing back the most recently recorded segment.

LOCK

Enable/Disable the Keypad function

1,2,3,4

Select the channel to monitor in full screen

FREEZE

Turn on/off screen freeze function.

Switch to quad display.

ENTER/MODE

Switch to full screen, quad display.

MENU/

Enable/ Disable setup Menu.

BK-UP/ESC

Enable/ Disable backup menu.

SRH

Enable/ Disable search menu.

MUTE

Switch channel 1 output audio / turn off LIVE audio

STATUS

Enable/ Disable Status.

OSD

Turn on/off the screen display

Zoom/Zoom -

Enable/ Disable double screen size display. You can click on the channel name for choosing a specific channel.

PIP/Zoom +

Turn on picture-in-picture format. Click on the channel name can switch to other channels.

PTZ

Enable PTZ control.

AUTO

In AUTO mode, all available channels will be cycled through in full screen.

HL-104 User Manual V0.6(M02)

Table 3-1.2 Graphical icons that will display after right-clicking your mouse under LIVE mode.

Icon

Description

Resting the cursor on this icon will bring up the following four menu icons.

Main menu.

Search menu.

Backup menu.

PTZ mode.

Turn on/off recording.

Playback.

Resting the cursor on this icon will bring up the following five display icons.

FREEZE.

PIP, picture in picture

ZOOM, double the screen size

AUTO-sequence

LOCK, activate the key lock.

Full screen display.

Quad display.

HL-104 User Manual V0.6(M02)

Table 3-1.3 Description of on screen graphical icons in LIVE mode

Icon

Description

Recording is on

1~4

Live Audio is on

Live Audio is off

Motion detected on the channel

Sensor triggered on the channel

Video loss detected on the channel

USB device detected

DVD burner is detected

Connected to the LAN cable.

Film：Normal Recording Clock：Schedule Recording

AUTO-seq is on

2X zoom in is on

Freeze is on, screen is frozen

LOCK is on

PTZ control is on

Shows the current hard disk space has been used (99% mean used 99%, remain 1%)

Lower right of each CH will show the current time

Icon

Description

Image quality (High/Low)

Full screen

Record

Snap shot (Photo time in accordance with computer-based)

Record and snap shot file saving path setup

Enable/Disable shortcut toolbar

HL-104 User Manual V0.6(M02)

3-2 PLAYBACK Mode

Switch to PLAYBACK mode by pressing “PLAY” under the LIVE mode, the graphical icon

will show up on the upper center of the screen and the operation panel ( see below picture) will show up at right lower corner of the screen. You can drag the panel by mouse to place it on any location of your screen.

Table 3-2.1 Remote control functions under the PLAYBACK mode

Button

Description

ENTER / MODE

Switch to full screen, quad.

MENU /

Turn on/off PAUSE.

PLAY

Play back at normal speed.

/ SLOW

Play back at slower speed. The speed will be slowed to 1/2, 1/4, 1/8, 1/16 by each pressing of the button till the slowest limitation of 1/16 of the normal speed. Current playback speed is shown in the upper center of the screen.

Fast rewind. Each press increases the speed to the next level. There are six speeds: 2x, 4X, 8X, 16x, 32X and 64X.

Fast forward. Each press increases the speed to the next level. There are six speeds: 2x, 4X, 8X, 16x, 32X and 64X.

Stop playback.

HL-104 User Manual V0.6(M02)

Table 3-2.2 The mouse operation under the PLAYBACK mode.

Icon

Description

「 / 」 Fast rewind

「 / 」Fast forward

／

Play/pause

「▲ / SLOW」， slow playback

「▼ / ■」stop playback

Playback channel by channel with snap shot display

Full screen display

Quad display

Zoom-in display

HL-104 User Manual V0.6(M02)

3-3 PTZ Mode (not available on HL-104)

Switch to the PTZ mode by pressing “PTZ” button under the LIVE mode. The PTZ icon will appear on upper left side of screen and the control panel will appear on the down right side of screen.

Table 3-3.1 Remote Control functions under the PTZ mode

Button

Description

/ SLOW

Move PTZ up.

Move PTZ down.

Move PTZ to the left.

Move PTZ to the right.

ZOOM +

PTZ zoom-in.

ZOOM -

PTZ zoom-out.

FOCUS +

PTZ focus-in.

FOCUS -

PTZ focus-out.

IRIS +

PTZ iris-open.

IRIS -

PTZ iris-close.

TOUR

Activate PTZ pre-set tour. ＊

PRESET+ Number

Setup the Preset location Press “PRESET” key first then two-digit number; DVR will set the current

PTZ location at entered preset number.

PLAY+ Number

Go to Preset location Press “PLAY” key first then two-digit number, PTZ will go to the

correspondent preset number location.

PIP

Set current PTZ location as the start of line-scan. ＊

FREEZE

Activate auto line-scan. ＊

ZOOM

Set current PTZ location as the end of line-scan.＊

＊ PTZ communication protocols from different brands aren‟t compatible 100% sometime

s. Therefore, some of these functions may be unavailable.

HL-104 User Manual V0.6(M02)

Table 3-3.2 Mouse operation under the PTZ mode

Icon

Description

Leave PTZ Mode，back to the LIVE mode

Pre-set number N. (0~255)

Go to pre-set number N.

Set current PTZ location at pre-set number N.

「TOUR」， press to activate pre-set tour＊

「PIP」， Set current PTZ location as the start of line-scan. ＊

「FREEZE」， Activate line-scan. ＊

「ZOOM」， Set current PTZ location as the end of line-scan. ＊

To move PTZ in 360° PTZ zoom in; PTZ zoom out

PTZ focus in; PTZ focus out.

PTZ IRIS open, PTZ IRIS close.

Below functions need support from specific PTZ manufacturer. Please check us er manual of your PTZ for more detail.

AUX 1~8,「AUTO」Key ＋ Number key「1~8」

「Backup」, Customized function。

＊PTZ communication protocols from different brands aren‟t compatible 100%

sometimes. Therefore, some of these functions may be unavailable.

HL-104 User Manual V0.6(M02)

CHAPTER 4 MAIN MENU SETUP

To enter the main menu and set up DVR, log-in account and user password are required. The default password of the administrator is “123456”. Please check the “Account Setup” for related setup of other log-in users.

Table 4-0.1 Some definition of virtual keyboard.

Item

Description

Switch between capital and small letters.

Switch between numbers and letters.

Press to cancel the setup, and re-choose the login

account.

Delete the last character.

Enter to identify the password. It will enter the set up menu, If the password is verified.

Space key

HL-104 User Manual V0.6(M02)

Table 4-0.2 The operation of remote control under the setting menu

Item

Description

Switch to different options under one item

Switch to different items

Save setup and back to LIVE mode

ESC

Back to Upper level of menu without saving

ENTER

Enter the menu, or display virtual keyboard

PS. The initialization of new-installed HD is required before recording, please refer to “4-9 UTILITY SETUP” for detail.

4-1 RECORD SETUP

HL-104 User Manual V0.6(M02)

Item

Description

HDD FULL

Select STOP to stop recording or OVERWRITE to reuse the HDD when HDD is full

「

Stop

」：

Stop Recording

「

Overwrite

」：

Start to overwrite that begin from the oldest data

of HDD, and continue to record.

Quality & Frame Rate Setup

Setup the quality and frame rate for each channel under normal recording and event recording type.

OSD position X

Setup OSD X axis

OSD position Y

Set up OSD y axis

Recording OSD position setup

Set up OSD axis

HL-104 User Manual V0.6(M02)

4-1.1 Quality & Frame Rate Setup

Item

Description

Normal setup/ event setup

Select recording mode

Resolution

Select recording resolution: NTSC:360x240, 720x240, 720x480 PAL:352X288,704X288,704X576

Record Type

You can setup quality and FPS separately for record type.

No.

Check/uncheck the box enable/disable selected channel recording

Quality

Select quality: Below Basic/ Basic/ Normal/ High/ Highest

FPS

Select recording frame rate.

Auto

Assign each channel with its maxima accessible fps

4-2 EVENT SETUP

HL-104 User Manual V0.6(M02)

Item

Description

Motion Setup

Enter to set up motion detection

Sensor Setup

Enter to set up sensor detection

4-2.1 MOTION SETUP

Item

Description

Motion Popup

Check the box to Enable/Disable popup screen function for all channels. When motion is detected in LIVE mode, the detected channel image will pop up in full screen display.

1~4

You can setup independently for each channel.

Selected Channel Turn

Check the box to Enable/Disable motion detection for each channel.

Sensitivity

Drag the white bar or press ◀ ▶ to set up Sensitivity from value 1 to 10 for each channel. The lower value you set the higher sensitivity it will be

Motion Area Setup

Enter to setup motion detection area

HL-104 User Manual V0.6(M02)

4-2.1.1 MOTION AREA SETUP

The motion detection has been divided into 16x12 grids. The default detection area is full screen as it marked in transparent for local DVR and purple for remote access. Areas deselected for motion detection are marked in red for both local and remote site.

Item

Description

Mask Mouse Selection

Switch between “select” and “deselect” for cursor-dragging function

All Area Detection

Select entire screen as detection area.

Mask All Area

Deselect entire detection area.

Continue

Continue setup

Exit & Save

Save setup and leave

Exit & Discard

Cancel setup and leave

4-2.2 SENSOR SETUP

HL-104 User Manual V0.6(M02)

Item

Description

Sensor Popup

Check the box to Enable/Disable popup screen function for all channels. When Sensor is detected in LIVE mode, the detected channel image will pop up in full screen display.

All Off

Set all sensor off

All Low

Set all sensor polarity low

All High

Set all sensor polarity high

Sensor Polarity

Click or press ▼ to select between HIGH, LOW voltage for triggering sensor detection or OFF to turn off polarity for each

channel Low Polarity：Sensor has not been triggered. When connected,

sensor will be turned on..

High Polarity：Sensor has been triggered. When connected, sensor

status will be turned off..

Off ：Sensor is deactivated, and will not be turned on/off.

4-3 SCHEDULE SETUP

Except from starting recording manually, you can also setup the recording time by weeks and schedule including normal, motion detect, and sensor detect recording type.

Item

Description

Page

Each page provides 10 schedules for setup. 5 pages in total.

Holiday Setup

Enter to setup holiday, up to 50 days, other than weekends,.

View Event/ Motion/ Sensor Setup

View Normal/ Motion / Sensor Setup

HL-104 User Manual V0.6(M02)

4-3.1 Schedule Record Setup

Click on the time on the left side. The setup menu will be displayed. You can have detail setup by dates, Time and event.

4-3.2 Holiday Setup

Since holidays are different by different country and region, you can setup the holiday of your location accordingly.

HL-104 User Manual V0.6(M02)

4-4 CAMERA SETUP

Item

Description

1~4

You can setup independently for each channel.

Mask

Check the box to Enable/Disable mask function for LIVE mode

Sharpness

Drag the bar or press ◀ ▶ to adjust Sharpness of your camera from

value 1 to 255. The default value is 1.

Brightness

Drag the bar or press ◀ ▶ to adjust Brightness of your camera from

value 1 to 255. The default value is 128.

Contrast

Drag the bar or press ◀ ▶ to adjust Contrast of your camera from value 1 to 255. The default value is 100.

Chroma(U)/(V)

Drag the bar or press ◀ ▶ to adjust Chroma of your camera from value 1 to 255. The default value is 128.

Hue

Drag the bar or press ◀ ▶ to adjust Hue of your camera from value 1 to 255. The default value is 128. ( This function doesn’t support at

PAL system)

Name

Set up name of each channel

Volume

Audio volume for CH1 under LIVE mode and recording mode can be adjusted.

HL-104 User Manual V0.6(M02)

4-5 ACCOUNT SETUP

The Account Setup menu is used to provide role-based permission independently setting for each user (maximum of 2 users) to access DVR over network. The default admin account and password is “admin” and “123456” The default password remains the same after firmware

upgrade, however, it requires 8-digits for password length when you setup a new one

Item

Description

No.

Check to activate the user‟s account.

Username

Set up username

Password

Set up password for each user. Password is 8-digits required and can be mixed by letters and numbers with case-sensitive. Letters can be mixed with capitals or lowercases.

Permissions

Set up Permissions for each user

Change Admin Password

Change administrator‟s password

Picture

Change user‟s picture

HL-104 User Manual V0.6(M02)

4-5.1 Permission Setup

The Account Setup is set to provide individual user (maximum of 2 users) role-based permissions, including access to Setup menu, Network operation, PTZ function, Playback, Utility, Backup, Password expiry date and Mask on specific channels while playing back.

4-5.2 User Picture Setup

User can select picture wished to be changed to from hard drive.

HL-104 User Manual V0.6(M02)

4-6 NETWORKING SETUP

4-6.1 NETWORKING SETUP

There are three ways to connect to the network as followed.

4-6.1.1 DHCP

When DHCP is selected, IP address will be assigned by DHCP server automatically.

Item

Description

Connect type

Setup mode for network connection: (DHCP、LAN、ADSL).

HTTP Setup

Enter to set up HTTP

DDNS Setup

Enter to set up DDNS

Mail Setup

Enter to set up mail

HL-104 User Manual V0.6(M02)

4-6.1.2 LAN

Select LAN for network connection, the following information is required.

Item

Description

IP Address

Enter IP address provided by ISP

Subnet Mask

Enter IP address of Subnet Mask provided by ISP

Gateway

Enter IP address of Gate way provided by ISP

DNS

Enter DNS address provided by ISP.

(Note: The correct DNS address must be entered for DDNS function).

4-6.1.3 ADSL

Select ADSL for network connection, the following information is required.

Item

Description

User Name

Enter user name provided by ISP

Password

Enter password provided by ISP

HL-104 User Manual V0.6(M02)

4-6.2 HTTP Setup

Item

Description

Enable HTTP Server

Check to enable HTTP server. Users can remotely access into the DVR over the network if the HTTP function is activated.

Port

Enter a valid port value from 1 up to 65000. The default value is 80.

Auto

Assign each channel with its maxima accessible fps

No.

Chanel number

Quality

Set up record quality. There are below basic, basic, normal, high, highest

FPS

Set up record FPS

4-6.3 DDNS Setup

HL-104 User Manual V0.6(M02)

Item

Description

Enable DDNS

Enable/disable DDNS function.

DDNS Server

Enter the registered SMTP Server:

ez-dns、I-DVR.NET＊、DYNDNS.ORG、NO-IP.ORG、3322.ORG

SMTP Server

Enter the completed registered SMTP Server. (Including username

+ Server) If the user name is h.264 and you choose i-dvr as your

server, you should enter: h.264.i-dvr.net

User Name

Enter user name.

Password

Enter password.

＊ For more detailed I-DVR.NET operation instruction, please refer to appendix I.

4-6.4 Mail Setup

When event occurs (VLOSS, MOTION, SENSOR), email will be sent to the receiver account automatically.

HL-104 User Manual V0.6(M02)

Item

Description

Enable E-mail Notification

Check the box to enable/disable E-mal Notification function.

SMTP Server

Enter to set up SMTP Server name. (Varies according to the user)

User Name

Enter to set up User Name.

Password

Enter to set up Password.

Sender E-mail

Enter to set up e-mail address of receivers.

Receiver E-mail

Enter to set up e-mail addresses for up to 10 receivers individually.

Trigger Event

Enter to select events to send out E-mail notifications when below circumstances happen: Motion, Sensor and Vloss (Video Loss).

4-7 PTZ & RS485 SETUP (not available on HL-104)

The DVR allows users to control PTZ functions of your camera. To enable PTZ function, the 485 cable should be connected to the RS-485 port of DVR.

Item

Description

Enable PTZ

Click the box to Enable/Disable PTZ function for each channel.

Protocol

Set up the protocol of PTZ cam. The supported protocol are

PELCO-P, PELCO-D, KND, LI-LIN, SAMSUNG, LG, AVTECH.

PTZ ID

Click or press ◀ ▶ to set up PTZ ID. The valid ID value is from 1 to 64.

Baud Rate

Select Baud Rate for PTZ from 2400, 4800, 9600,19200

RS-485 ID

Select RS-485 ID from 1 to 64

RS-485 Baud Rate

Select RS-485 Baud Rate from 2400. 4800, 9600,19200

Keyboard

Select Keyboard. (Li-Lin)

HL-104 User Manual V0.6(M02)

4-8 SYSTEM SETUP

Item

Description

DVR Name

The name of DVR will be shown when users login from remote access.

DVR Location

The location of DVR will be shown when users login from remote access

Language

Click or press ▼ to select OSD language from English, Traditional Chinese, Simplified Chinese, Japanese, Greek, Portuguese

Remote ID

Default ID is 0. When more than one DVRs are purchased, the DVRs can‟t be numbered from 1 to4. For instance, standard remote control can‟t operate DVR numbered 3. It only responds when use 1 to 4 remote control.

Display Setup

Enter to set up Display

Date/Time Setup

Enter to set up Date/Time

Device Setup

Enter to set up Buzzer & Relay

Spot Setup

Enter to set up Spot

HL-104 User Manual V0.6(M02)

4-8.1 DISPLAY SETUP

Item

Description

Auto-Seq Interval

Set up duration time in seconds for the interval between channels under Auto-Seq mode.

Show OSD

Turn On / Off OSD display

Show DVR Status

Turn On / Off DVR illustration and record status display

Show Date/Time

Turn On / Off date and time display

Show Channel Name

Turn On / Off channel name display

CRT

Deflicker(only for CRT monitor)

Border Color

Set up the color of border in LIVE , PLAYBACK mode.（Red, Green, Blue）

4-8.2 DATE/TIME SETUP

HL-104 User Manual V0.6(M02)

Item

Description

Hour Format

12HOURS/ 24HOURS

Date Format

MM-DD-YY/DD-MM-YY/YY-MM-DD

Date/Time Position

Choose the position of Time and Date display

Change Date & Time

Setup time and date of DVR

Time Zone Setup

Set up GMT and Daylight Saving Time.

Internet Time Setup

Setup automatic synchronization with internet server

4-8.2.1 CHANGE DATE & TIME

Setup date and time of DVR manually according to user‟s local time.

4-8.2.2 TIME ZONE AND DAYLIGHT SAVING TIME SETUP

Set up time zone and activate Daylight Saving Time function according to user‟s DVR location.

HL-104 User Manual V0.6(M02)

Item

Description

Select Time Zone

Enter to modify GMT from GMT- 13 to GMT+ 13

Daylight Saving Time

Turn on/ off Daylight Saving Time

4-8.2.3 INTERNET TIME SETUP

Synchronize your DVR time with internet time server.

Item

Description

Automatic Synchronization

Check to enable DVR automatic synchronization function. Effective by this option selected, DVR will automatically synchronize the time upon rebooting or by every 24 hours after booting.

Update Now

Effectively, Date and Time show on DVR will immediately correspond with those in internet server.

4-8.3 BUZZER & RELAY SETUP (not available on HL-104)

HL-104 User Manual V0.6(M02)

Item

Description

Key Tone

Enable/Disable keystrokes.

Buzzer

Enable/Disable buzzer operation when the alarm is triggered for HDD Error, Video Loss, Motion and Sensor.

Relay

Enable/Disable the signal to be sent to the RELAY OUT blocks when the alarm is triggered for HDD Error, Video Loss, Motion and Sensor.

4-8.4 SPOT SETUP (not available on HL-104)

The DVR has two modes of video output; one is main video output, the other is spot video output. SPOT setup is for controlling the order of channels the system cycles through in SPOT mode. User can monitor every channel in the SPOT mode.

HL-104 User Manual V0.6(M02)

Item

Description

SPOT MODE

Channels display in spot for three different modes:

MANUAL: select channels to display manually. SEQUENCE: Auto-sequence for all channels in order. EVENT: Display channels with event occurred.

Interval (Seconds)

The duration time in seconds for the interval between channels under SPOT mode.

Skip Video Loss Channel

Whether to skip channels without video signal.

4-9 UTILITY SETUP

Item

Description

HDD Initialization

Select to enter hard disk initialization menu. Please stop recording before entering this menu. Enter the menu,

system will show all the data (model ,volume ) of HDD that installed in DVR. Check the HDD you‟d like to initialize then press “Start”. HDD initialization is successful when the status shows “Succeed”

USB Initialization

Clean up all data on USB. Enter USB initialization and press YES to clean up all data on your USB. The initialization is done when it‟s showed “Succeed”.

System Recovery

Restore system default values

Reset System Events

Reset all the recording events in DVR.

Copy Setup to USB

Copy configuration to a USB device. There will be a file named “sdvr.config” on your USB.

Download Setup from USB

Download configuration from a USB device into DVR.

Upgrade

Upgrade DVR through USB. Please stop recording and backup setup configuration before upgrading.

System will reboot automatically when the upgrade is completed.

Notice! DO NOT TURN OFF POWER OR UNPLUG USB DEVICE DURING THE UPGRADE

as it may cause incomplete firmware upgrade and damage to the DVR.

HL-104 User Manual V0.6(M02)

4-10 DIAGNOSTIC

Item

Description

Version

The current firmware version of DVR

The connected IP address of DVR. If disconnected from network, the screen will display” NETWORK DISCONNECT”.

MAC

MAC Address of DVR

HDD Status

No.

HDD number

Volume

HDD Capacity

Used

Percentage of space used on HDD.

Status

Shows HDD status.

USING means the HDD is being used for recording now GOOD/BAD means the HDD has a known/unknown format

for the DVR. (Note: Please initialize your newly-installed HDD before using it.)

Format

The latest format time of HDD

HL-104 User Manual V0.6(M02)

CHAPTER 5 BACKUP & SEARCH

5-1 BACKUP SETUP

User can backup any segment of recorded data in a specified time frame. To do so, either a CD R/W or storage device, like USB, must be connected to the DVR. Recorded data can also backup into NB/PC through our remote access software: 「DVRemoteDesktop.exe」 and be

saved in your assigned path. The format of backup file is IRF file that can be played by both “DVRemoteDesktop.exe” 、 “ifileplay.exe” and “CMS”

Item

Description

From

The start time of backup file

The end time of backup file

Device

Select USB, PC as the backup device

Free Space

The available space in your backup device. (not available for PC backup)

Refresh

Recalculate the available space of backup device. (not available for PC backup)

Required Space

Show the size of the backup file

Calculate

Calculate the size of backup file

Start

Start backup operation.

Be sure to calculate the size of backup file BEFORE operating backup.

Note! Do not unplug the USB device or turn off the DVR during the backup process to

avoid unrecoverable error.

HL-104 User Manual V0.6(M02)

5-2 SEARCH SETUP

Item

Description

Event Search

Event search menu

Time Search

Enter time search menu

HL-104 User Manual V0.6(M02)

5-2.1 EVENT SEARCH

The DVR automatically records events with type, time and channel information included. If there is recording data for an event, a yellow signal will be shown on the left side of time

information. Rest your cursor under the line and press “enter”, or left click your mouse to playback the recording data.

P.S. Event Records will still be generated even when hard disk is not installed or the record function is not activated. However, the record can’t be viewed after selecting it.

Item

Description

Page

Switch between pages of events

Date/Time

Date/time when event occurred.

Event Type

Event type, defined as following

MOTION

Motion Detected

SENSOR

Sensor Detected

Video Loss

Remote Login

user log-in over the network

Remote Logout

user log-out over the network

Power On

DVR Power on

HDD Full

HDD Space FULL

HDD Error

Detect HDD error

Reboot

DVR Reboot

Info

The channel where event occurs or login user

HL-104 User Manual V0.6(M02)

5-2.2 TIME SEARCH

TIME SEARCH can search for the specific time of recording data to playback. Press “Enter” or left click on the desired date to playback. Note that dates with recording data are marked with a red square “ □ “System will start playing back according to the date you selected. Calendar

will be shown by using mouse to click on “year” and “month”.

Click “date” to display recording time of that specific date with time bar. You can change time (hour/minute/second) or click on a specific time of time bar by mouse then press “ok”. DVR will playback the selected recording data.

AP software:「DVR Remote Desktop」can allow you to remotely access and control the DVR from PC.

HL-104 User Manual V0.6(M02)

CHAPTER 6 Rempte Software Installation and Setup

6-1 AP Software Installation and instruction

AP software:「DVR Remote Desktop」can allow you to remotely access and control the DVR

from PC.

p.s. Operation system currently supports Windows XP SP2 and above and Window s Vista, Windows 7

Step One：Enter the IP address of DVR in IE browser

Step Two: Windows as below will show up. Please enter the user name and password. Default

user name and password is admin/123456. Other related setup about user account and password, please check “4-5 Account Setup. “

Step Three: Click on the link to start downloading the AP software.

HL-104 User Manual V0.6(M02)

Step Four: Run or Save our AP software.

Step Five: If you choose to run the software, Start window will be shown up. Please enter

information of login DVR: IP, Port, Username and Password, or choose “Play Recorded File” to open backup files in your PC.

Step Six: You‟ve logged into the DVR

HL-104 User Manual V0.6(M02)

6-2 How to do remote monitoring through IE

Step One：Enter the IP address of DVR in IE browser. The address appeared in this image is

only for demonstration. Actual address is depending on the setup of on-site DVR.

Step Two: Windows as below will show up. Please enter the user name and password. Default

user name and password is admin/123456. Other related setup about user account and password, please check “4-5 Account Setup. “ The user name and password

appeared in this image is only for demonstration. Actual user name and password depend on the setup of on-site DVR.

Step Three: Click on “Internet Explorer 6, 7, and 8”to start downloading the AP software. ( The first option is for IE view, please refer to next chapter for more information)

p.s. There will be IE connection security issue when clicking this link for the first time. Please refer to index II for Remote Monitoring IE ActiveX Control Installation Instruction.

HL-104 User Manual V0.6(M02)

Step Four: DVR images appear.

6-3 AP Software Operation

Open the file “DVRemoteDesktop.exe”; enter the information of DVR “IP address”, “Port”

“Username” and “Password” and click “OK”. You should be able to login DVR successfully and

start to use the software. The default username and password is 「admin/ 123456」

“DVRemoteDesktop.exe” AP software provides some extra functions for remote users. Please check Table 6-3.1 for minimum system requirements for “DVRemoteDesktop.exe” operation.

Table 6-3.1 System Requirements for AP software

CPU

Intel Pentium 4 above

Microsoft Windows 7、Windows Vista、Windows XP SP2 above

RAM

512M above

VGA Card

Needed to support DirectX9.0 (Above) Note 1

Others

DirectX 9.0 above

Note 1:

Known VGA card that support DirectX9.0 currently:

NVIDIA: Geforce FXseries, Geforce 6series, Geforce 7series, Geforce 8series, Geforce

9series, Geforce 200series, etc.

visit:http://en.wikipedia.org/wiki/Comparison_of_Nvidia_graphics_processing_units

ATI: Radeon R300series, Radeon R400series, Radeon R500series, Radeon R600series,

Radeon R700series, Radeon HD 3xxx IGPseries, Mobility Radeonseries (9500 above), Mobility Radeon Xseries, Mobility Radeon HDseries, or FireGL Vseries etc. Or visit: http://en.wikipedia.org/wiki/Comparison_of_ATI_graphics_processing_units

SiS: SiS 67Xseries, or SiS 77Xseries etc.

Or visit: http://www.sis.com/support/support_compare.htm

Intel: 91Xseries, 94Xseries, 96Xseries, G3Xseries, or G4Xseries, etc.

Or visit: http://en.wikipedia.org/wiki/Intel_GMA

HL-104 User Manual V0.6(M02)

CHAPTER 7 SPECIFICAITONS

1. VIDEO

Input Level

1.0 Vp-p±10% Composite, 75 Balanced

Display Speed

NTSC

120fps

PAL

100fps

Display Resolution

NTSC

704(H) X 480(V)

PAL

704(H) X 576(V)

Monitor Output

2Vp-p Composite, 75 Balanced

2. RECORDING

Compression Method

H.264

Recording Speed

Refer to table 7-1

Recording Resolution

NTSC

704 X 480, 704 X 240, 352 X 240

PAL

704 X 576, 704 X 288, 352 X 288

Quality

Independent for each channel

Below Basic/ Basic/ Normal/ High/ Highest

Schedule

Setup by “minute” as unit

Mode

Manual / Event (Motion) / Schedule

Method

By resolution, fps and quality Setup fps and quality separately for normal and

event recording

3. SATA DEVICE

Capacity

Internal Storage

1 HDD

Type

SATA / SATAⅡ compatible

4. ALARM

Sensor Input

4 Loop Out

1 Relay out

Motion Detection

Available per each camera/ Multi-detection level

5. CONNECTIONS

Video Input

4 ports

Video Output

BNC 1 port, VGA 1 port (max.1920 X 1080)

Audio Input

RCA 1 CH

Audio Output

RCA 1 CH

USB 2.0

USB memory stick, USB Touch Panel

USB 1.1

USB Mouse

Remote

Remote control

External I/O

1 RS-485, 4 sensor input, 1 Relay Output

Ethernet

1 RJ45 connector, 10/100 Mbps

6. ELECTRICAL

Power Source

DC 12V / 3A

7. ENVIRONMENTAL

Operation Temperature

5℃ ~ + 40℃

Humidity

Less than 90%

HL-104 User Manual V0.6(M02)

8. PHYSICAL

Dimension

300(W) x 175(D) x 46(H) mm

Weight

1.3 KG（not including HD）

9. BACKUP

BACKUP USB Stick

Video Data, Audio

Network

Video Data, Audio

10. SEARCHING & PLAYBACK

Searching Type

Event/ Time

Playback speed

120 FPS

11. MULTI-REMOTE SURVEILLANCE

Monitoring Environment

Web/AP/CMS

Max. client

Supporting multi-client (3 clients accessible)

12. OTHERS

Embedded Linux

Multi Task

Pentaplex

Live、Record、Playback、Network、Backup

Control Device

Remote Control / Virtual Keyboard / Mouse / AP Software

PC Viewer

Direct monitoring of DVR‟s HDD on PC

Numbers of event list

10000

Table 7-1

Recording Speed

(Independent

setting for each

channel)

NTSC

360 x 240

120 FPS

720 x 240

60 FPS

720 x 480

30 FPS

PAL

352 x 288

100 FPS

704 x 288

50 FPS

704 x 576

25 FPS

Compression Method

H.264

HL-104 User Manual V0.6(M02)

CHAPTER 8 MOBILE APPLICATION INSTALLATION AND USAGE

You can remotely monitor all channels of DVR through your mobile device. The required mobile application is from DVR manufacturer and it supports mobile OS for both Windows mobile 5.0 above and Symbian.

Please confirm network function of DVR has been activated before mobile connection: Main menu  Network Setup  HTTP Setup  Check the “Enable HTTP Server”

8-1 Mobile Application Installation and Operation for Symbian System

Mobile Device: Nokia, SonyEricsson…etc. System requirement:

GPRS/ 3G must be provided from your telecom service. Mobile device that supports GPRS/ 3G protocol and Java cldc1.0/midp 2.0 environment

＊Please download both” DVRH264.jar” and “DVRH264.jad” to operate the function. Note that users with Sony Ericsson will only need to download “DVRH264.jar.”

8-1.1 Mobile Application Installation

Please follow the steps cited below to perform the mobile device surveillance function.

Step 1: The mobile application called “DVRH264.jar” need to be installed in your mobile device.

The application can be downloaded directly from the manufacturer‟s website to your mobile or; alternatively, it can be transferred to your mobile device from the CD that packed with DVR through Bluetooth or USB cable.

Step 2: Install the application software “DVRH264.jar” in your mobile device. It might be

installed automatically after downloading; otherwise, select it from the downloading file for installation.

HL-104 User Manual V0.6(M02)

8-1.2 Mobile Application Operation

After the installation, enter the Program Files menu in your mobile device to run a file called “DVRH264”.

Select “Menu” at the right lower corner of your mobile screen, 4 commands, Login Add Modify and Delete, will show up.

8-1.2.1 Add New Login DVR

To log into the DVR, you need to enter the logging-in DVR information. Find “Add” under the “Menu” then enter logging-in DVR‟s IP address, Port number, account name and password. Press “Add” to save this information after entering.

8-1.2.2 Logging Onto the DVR

Use the Login command to log onto a DVR and monitor live images. If multiple DVRs have been added to the mobile application, they will be listed by name, you can select one to log onto.

A confirmation message might show up for network charge before connection. The fee rate will depend on the telecom company and package fee you go with.

Network connectivity will take some time. It‟ll be affected by networking environment and bandwidth flow. Live image will show up after a successful connection.

PS. The Live can not be displayed in your mobile when the recoding is off in local DVR.

HL-104 User Manual V0.6(M02)

8-1.2.3 Modify the Login Information of DVR

You can use the “Modify” command to change the login information of DVR. The dialogue is identical to that of the “Add” command.

8-1.2.4 Delete the Login Information of DVR

“Delete” command can be used to remove the DVR information if it is no longer useful. Select the DVR on the name list then choose “Delete”

8-1.3 Live Monitoring Operation

This paragraph describes some operation under the LIVE monitoring mode in your mobile

HL-104 User Manual V0.6(M02)

device.

8-1.3.1 Scroll the Image

You can use the keypad on your mobile device to scroll the image if it‟s oversized.

Key

Action

Scroll Up

Scroll Left

Scroll Right

Scroll Down

8-1.3.2 Image Quality Setup

Select “Quality” under the “Menu”

There will be 5 levels for your to choose: Low、 Normal、Middle、High and Highest.

8-1.3.3 Channel Display

Select “Single” under the “Menu”, there will be all channels of your DVR in list for you to choose.

PS. The Live can not be displayed in your mobile when the recoding is off in local DVR.

HL-104 User Manual V0.6(M02)

8-1.3.4 Size of Image

The screen size of different mobile device can be different. You can select “Size” under the “Menu” to choose from “Original” or “Fit Screen” to resize the display image.

Item

Description

Original

The image will be shown in original size.

Fit Screen

The image will be shown to fit the screen.

8-1.3.5 Rotate the image

The Live image can be displayed in normal or rotate to 90 degrees. Select “Rotate” under the “Menu” for this operation.

8-1.3.6 Alarm

This application not only allows you to remotely monitor through mobile device but receive the alarm that has been triggered by events such as Motion Detected, Sensor Triggered and Vloss.

Graphical icons below will be shown on the status:

: Motion detected

: Sensor triggered

: Video loss

Select the “Alarm” under the “Menu” to switch this function on or off.

HL-104 User Manual V0.6(M02)

8-2 Mobile Application Installation and Operation for Windows Mobile System

There are two kinds of applications for Window Mobile OS: JPEG compression and H.264 compression. The one for H.264 compression can transfer both audio and video signal to your mobile device.

System Requirement: Mobile device OS：Windows mobile system 5.0 above.

Mobile device need to support internet: GPRS／3G／Wifi… etc.

8-2.1 Mobile Application Installation

Please follow the steps cited below to perform the mobile device surveillance function on your mobile device (mobile phone, PDA ...etc).

Step 1: The mobile application called “Jrviewer.CAB” and

“H264Pocket.CAB” need to be installed in your mobile device. The application can be downloaded directly from the manufacturer‟s website to your mobile or; alternatively, it can be transferred to your mobile device from the CD that packed with DVR through Bluetooth or USB cable.

Step 2: Install the application software “Jrviewer.CAB” and “H264Pocket.CAB” in your mobile

device, two folders named ”Jrviewer” and “H264Pocket” will be created. It might be installed automatically after downloading; otherwise, select it from the downloading file for installation.

HL-104 User Manual V0.6(M02)

8-2.2 Mobile Application Operation

After the installation, enter the Program Files menu in your mobile device to run files named “Jrviewer” and “H264Pocket”.

This application allows you to remotely logon and monitor DVR. Press “OK” to bring up the operation menu, see below chart to further information.

Item

Function

Description

Add

Add login DVR

Enter DVR‟s name, IP address, Port, Account user, Password then press “OK”

Logon DVR

‧Choose the DVR that you‟d like to log on , then press “OK” ‧ PS. The Live can not be displayed in your mobile

when the recoding is off.

‧PS. Network connectivity will be affected by networking

environment and bandwidth flow. The fee rate will depend on the telecom company and package fee you go with.

Modify

Modify Login DVR

Choose DVR, press “Modify”, and press”OK” to save change.

Delete

Delete Login DVR

Choose DVR and press ”Delete” to delete the DVR info.

HL-104 User Manual V0.6(M02)

8-2.3 Operation under the LIVE monitoring.

After successful logon the DVR, press “View” to bring up operation menu. You can choose the channel, resize the image, choose the quality, and turn on/off the status bar, alarm, full screen display….etc

Item

Function

Description

Channel 1~16

Display for CH 1~16

Choose from CH1~16 to display. (Show only supports a single partition)

Status Bar

Graphical icons indicated below will be shown on the status bar if there is event such as motion detected, sensor triggered and video loss to be detected on any channel. You can

also uncheck the “Status Bar” to inactivate

this function.

Icon

Description

Motion Detect

Sensor Trigger

V-Loss

Alarm

Alarm through your mobile device can be triggered if there is event to be detected. You

can also uncheck the “Alarm” under the “View” to inactivate this function.

Sound

If the channel video with sound input, turn this option to hear the real sound.

Full Screen

Full screen display

You can choose one channel to display in full screen by check this function.

HL-104 User Manual V0.6(M02)

CHAPTER 9 CMS INSTALLATION AND USAGE GUIDE

9-1 CMS Installation

System Requirement:

＊Intel Pentium 4 processor or equivalent. ＊Microsoft Windows Vista、Windows XP、Windows 2003 Server.

＊Besides OS and other required APs, there will be 512MB remaining memory needed or above. ＊512MB memory above.(500M requested for group DVR connection and 180M for single DVR) ＊20MB HD space. Recording and image capturing require extra space for storage. ＊VGA Card needs to support DirectX9 and function well while running it. Please refer to

p40 Note 1. Installation:

1. Connect to the manufacturer‟s website and download the CMS software.

2. Decompress and execute “setup.exe”.

3. If “Visual C++ Runtime Libraries” has not been installed before in the operating PC, the

following sign will suggest an installation automatically.

4. Select “Next”, and then select “Browse” to change installation path if needed. To check

available space on hard disk, please select “Disk Cost” then please select “Next” to the next step.

HL-104 User Manual V0.6(M02)

5.”Confirm Installation” window shows. Select „Next’ then the installation starts.

6. Select „Close’ to finish installation when the “Installation Complete” window shows.

HL-104 User Manual V0.6(M02)

Instruction for Log-in Failure to CMS After Upgrade

Log in to CMS with the default account and password after CMS upgrade. If an error message occurs as shown in the image, please follow the instruction to solve the error.

Step 1: Please enter file manager to enter folder, “Windows” and then folder “Systme32”

(ex:C:\Windows\System32)

Step 2: Locate file, “iCMS.dat” and delete it.

Step 3: Restart CMS. Log-in successfully.

HL-104 User Manual V0.6(M02)

9-2 CMS LOGIN AND ENVIRONMENT

To enter CMS, the administrator‟s user name and password are required. The defaults are „admin‟ and „123456‟.

After successful login, the following image shows on your screen:

① DVRs, Groups &

Events

Information about DVRs, groups and events. See “9-3 Information List” for more detail.

② PC information

and control

Information about local PC‟s hard disk, volume, recording...etc. See “9-4 PC Information and Control” for more detail.

③ Main Display

Live image display area. See “9-5 Main Display” for detail.

④ Display Modes

Several choices of display modes supported by CMS.

⑤ Operation Bar

A set of 10 operations are provided by CMS. See “ 9-6 Operation Bar” for detail.

①

②

③

④

⑤

HL-104 User Manual V0.6(M02)

9-3 DVRs, Groups & Events

Icon

Description

View list of logged in DVR／ Group.

View Logs: list all the event information of DVR

9-3.1 View DVR／Group List

Single left click on „DVR’ or „Group’ will expand/collapse the entire DVRs and groups list.

On the DVR list, double left click on a

connected DVR will show its image in main display. See “9-6.2 DVR

Administration” for further information.

On the Group list, double left click on a

group will show live image from the channels of the group in the main display. See “9-6.3 for Group

Administration” for further information.

Left-clicking on a connected DVR will expand/collapse status of its all channels as below:

Icon

Description

Video Loss

Motion Detected

Sensor Triggered

HL-104 User Manual V0.6(M02)

9-3.2 View Event Logs

Under this page, all the events of a DVR can be expanded/collapsed in the order of Re mote in/Remote out, Video Loss, Motion, Sensor, Others (Power Reset, Key Lock, Key Unlock, HD Full).

9-4 Local PC Information and Control

Located at the left lower corner of the screen, please see the chart below:

Icon

Function

Description

HDD info

Shows the ratio of available space / HDD capacity of C:\ drive (where CMS is installed).

Recording

iView Technology HL-104 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual