103DV
Medi a Pl ayer
iVIEW-103DV
1. COAXIAL OUTPUT
2. AUDIO LEFT OUTPUT JACK
3. AUDIO RIGHT OUTPUT JACK
4. VIDEO OUTPUT JACK
5. Y,PB/CB,PR/CR COMPONENT OUTPUT JACK
1. OPEN/CLOSE: to open/close the disc tray.
2. SUBTITLE: to display captions.
3. TITLE: to enter appointed titles.
4. MENU: to display the disc menu.
5. LEFT/RIGHT/DOWN/UP: to move cursor for selection
6. ENTER: to confirm.
7. REV: to scan in reverse.
8. FWD: to scan forward.
9. PLAY/PAUSE: to resume normal playback/ to pause playing.
10. VOLUME+/-: to increase/decrease volume.
11. DVD/USB : switch DVD to USB or switch USB to DVD
12. STOP: to stop playing.
13. RAN: to play randomly.
14. CLEAR: to delete numbers having been input.
15. N/P: to choose TV system: NTSC/PAL
16. L/R : to change audio output mode: left, right, stereo or mixed soundtrack.
17. Video :to select different video output mode (CVBS, YUV).
18. PROG: to programme.
19. OSD: to display info. of the current playing disc.
20. POWER:to enter standby mode or resume normal playback.
21. NO. KEYS: to input time, title, chapter and track number.
22. TIME: to select your desired time, chapter of the disc to play.
23. ANGLE: to switch different viewing angles.
24. LANGUAGE: to select the audio track language.
25. SETUP: to enter system setup menu
26. NEXT: to play next chapter/title/track.
27. PREV: to play previous chapter/title/track.
28. ZOOM: to enlarge/shrink the image.
29. MUTE: to mute the audio/ resume normal audio.
30. PBC: to select PBC modes: on/off.
31. RETURN: to go back to disc main menu (with PBC on)
32. SLOW: to slow down the playing speed.
33. REPEAT: to choose repeat modes: single/all/off.
34. STEP: to catch motions step by step.
35. A-B: to repeat A-B period.
33
34
35
27
28
29
30
31
32
26
19
20
21
22
23
24
25
2
3
4
5
7
8
9
10
11
12
13
14
16
15
17
18
6
1
Connection to Television
There are several possible configurations, depending on your television:
Connecting to a TV With Component Video cable(not include)
Connecting to a TV With Audio/Video cable
GB-8
DVD/USB
In stop mode, press the key from the remote control to switch the input source between
Disc and USB.
3.1
3. 2
4. There are 3 Repeat modes and 3 Mode states at the right side. Repeat Single is to
repeat single track. Repeat Folder is to repeat tracks in the whole folder. Repeat Off is to
cancel repeat. Mode normal is to play normally. Shuffle on is to play randomly. Music intro
is to play the prelude only.
Notes: To play randomly, preset repeat state as “Repeat: off” at the right side, mode state
as “Shuffle on”. Press NEXT from the remote control to play without sequence.
For DVD Program
For CD/MP3 program
Note: If song is being played while programming, press STOP button to stop current playing
before you choose program playing.
Note: Ensure you have chosen Edit Mode before clearing program.
Remark:
CVBS: Composite Video. Set the video output to interlacing component output.
YUV
Notes: It must be in stop status when choosing NTSC PAL Auto TV system.
Notes: It must be in stop status when selecting CVBS or YUV video output.
YUV: Set the video output to YUV output.
1) Power-on the unit.
2) Make sure no disc was played inside the tray.
3) Insert a USB key inside the connector.
4) Press the USB key from the remote control to start.
Remark: Depending on the capacity of the device, the reading can take more than 1 minute
before lauching the video.
The unit cannot read my USB device.
- Once you have plugged your device to the unit, you may need to switch on the USB device
before it can operate.
- This unit does not support a direct USB connection with a computer. You need to use a USB
device, a MP3 player .
- Check that the files system of your USB device is formatted into the FAT or FAT 32 format.
USB device formatted into NTFS are not compatible with this unit. Caution: if you attempt to
modify your file system, formatting your device will erase all data. Please refer to your USB
device’s instruction manual first.
- Warning: Connect your USB device directly to the USB port of the device. Using an extension
cable is not recommended and may cause interference and failure of data transfer.
5. Connecting a USB device
MPEG4 MPEG4
MPEG4
6
6
6
6
6
6
6
6
6
6
6
6.3.1 Digital Output
Selecting the Digital Output setting allows the user to adjust the audio output on S/PDIF ports to
work in harmony with the audio equipment (e.g. receiver, speakers) connected to the player.
Off: Digital audio output is disabled.
PCM: Select this option when you are going to use stereo signals (2 channels). You should combine
this option with “lower sampling rate”, which is explained further on.
Raw: If you select this option the player will play the DVD’s original audio track. Use this option when
you want to use the Dolby Digital AC3 signals through the optical or coaxial audio output.
6.3.2 Night Mode
This listening mode is most suitable at night for softest audio output and least disturbance.
CVBS: Composite Video. Set the video output to interlacing component output.
YUV: Set the video output to YUV output.
6
6
6
6
6
6
6
6
6
7.
Please consult the following section when you encounter problems using this DVD player. If
the player ceases to function properly after some wrong settings, you may restore the factory
defaults as described in Section 8.5.1 on the previous page. In all cases, for your safety, never
attempt to open the unit by yourself given the presence of dangerous voltage inside. Only the
technicians of the after-sale service are authorized to open and repair it.
NO PICTURE AND NO SOUND
- Press the Standby button to turn on the player.
- Check the power outlet and make sure that the plug is firmly inserted.
- Ensure the power cord is not damaged.
THERE IS SOUND BUT NO PICTURE
- Make sure you have connected the audio cable to the audio input (instead of an audio output)
on your television.
- Check if the sound is cut or reduced to minimum.
THERE IS PICTURE BUT NO SOUND
- You should set the video mode on your television to be YUV or AV-IN (Audio/Video Input).
DISTORTED OR BLACK AND WHITE PICTURE
- Choose the video mode (NTSC or PAL)
by pressing the N/
P button on the remote control. You
can change the default value of this setting in the player’s video menu.
CHOPPING SOUND OR IMAGE DURING PLAYBACK
- Check if the disc is not scratched or damaged. Try another disc.
- Make sure the YUV and the Audio/Video cables are connected firmly and correctly.
DISPLAY OF MESSAGE “NO DISC” OR “BAD DISC”
- Make sure you insert the disc on the correct side.
- Check if the disc is not scratched or damaged. Try another disc.
- Make sure that the disc format is supported by this player.
- The message may also appear in case of overheating. In this case, turn the unit off for
approximately an hour. Also leave sufficient ventilation space around the unit, as described at
the beginning of this manual.
REMOTE CONTROL PROBLEM
- Check battery status. If necessary, replace by two new AAA batteries.
- Make sure batteries are inserted by following the +/- polarity signs.
- Remove all the objects between the front of the DVD player and remote control.
MALFUNCTION
- Turn off the player then turn it on again. If necessary, disconnect it from the wall outlet.
THE DISC IS STUCK IN THE DISC TRAY
- Turn off the player. Then turn it on and immediately press the OPEN/CLOSE button on the
remote control.
120V ~ 60Hz
/MPEG4
8.
Loading...