V1.0
IR-650836-F80 IR Camera Function Description:
4
8
6
5
1 2
3
IR-650836-F80 IR Bullet Outdoor Camera Function Description:
1.) IR LED: There are 36 pcsψ8 IR LED which will be turned on when the light is lower than 0.5 Lux.
2.) Lens: 8 mm IR Lens. Provide 6mm/12mm as alternative choice.
7
185 mm
11
9 10
3.) Fix Hole: There are 4 holes to fix wall mount bracket.
4.) Sunshade Cover: To prevent the sunshine to camera directly.
5.) Vertical Screw: To adjust the vertical position of camera.
6.) Wall Mount Bracket: To fix camera on the wall and store cable inside the bracket.
7.) Horizontal Screw: To adjust the horizontal position of camera.
8.) Cabling Outlet: To connect the outside cable via these holes.
9.) LED: Power indicator, Green LED On: Power on. Green LED Off: No Power. Yellow LED: Reserve
10.) RJ-45 connectors: To transmit Power and Video signals via UTP cable. Please refer to the RJ45 pin assignment.
Socket cable: To Connect OSD control cable (Optional) for camera parameters setup.
11.)
PRX-120VP Function Description: (On DVR site)
Front Panel
PRX-120VP Back Panel
RJ-45 Connector Pins Assignment
1 2
1.) RJ-45 connector: To transmit Power and Video signals via UTP cable. Please refer to the pin assignment.
3
4
5
2.) LED: Power indicator, LED On: Power on. LED Off: Not enough power or No Power.
3.) BNC Cable: For video output to DVR.
4.) Terminal Blocks: Power input for power transmission. Accept power range DC 24V or AC 24V-28V.
5.) RJ-45 pin Assignment: Connect the 4-pair UTP cable between DVR site and camera end for video/power transmission.
WARNING: This camera MUST use DC 24V power adapter for power transmission up to 300 meters via Cat. 5 UTP cable.
1
Installation Notes:
1. Please use point-to-point Unshielded Twisted Pair wire, 24-16 AWG, Category 2, 3, 4, 5, or 6.
2. Please measure the wire distance, Use only transceivers that are designed for that distance.
3. Please make sure the pair of wires carrying the video signal is sent as a twisted pair (e.g. the Blue-white/White-blue
wires twisted together as a pair), not a “split-pair” (e.g. blue-white conductor, part of one pair / orange-white conductor,
part of another pair).
Installation Warning:
1. Please DO NOT USE SHIELD TWISTED PAIR WIRE. This will cause severe degradation on distance performance and
reduce the inherent interference immunity.
2. Please DO NOT have “bridge-taps” or loading coils in installation.
3. If the phone company provides the cable runs between buildings, make sure it’s “dry copper”.
4. Due to near-end cross talk, don’t send a transmitted and a received signal in the same wire bundle. For safety, DO
NOT put UTP cable in the same conduit as high-voltage wiring.
Specification:
Item Model
Image Device 1/3“ SONY EXview HAD CCD II (Effio-E)
Effective Picture Elements PAL: 1024(H)x596 (V); NTSC: 1028(H)x508(V)
Horizontal Resolution Color: 650TVL; B/W: 700TVL
Minimum Illumination Color: 0.03Lux@F1.0, B/W: 0 Lux (IR LED on)
Wide Dynamic Range ATR Digital WD (ATR: Adaptive Tone-curve Reproduction)
S/N Ratio More than 50dB (AGC Off)
IR-650836-F80 (60/120)
Shutter Speed Control AUTO (1/50(60) ~ 1/100,000 sec.)
Lens 8 mm / F2.0 (optional: 6mm/12mm)
Video Output RJ-45 connector; BNC composite connector (Option)
Gain Control Auto (4 steps)
White Balance ATW / PUSH / USER define / ANTI CR / MANUAL / PUSH LOCK
Back Light Compensation HLC / BLC / OFF
Gamma Characteristic 0.45
Day/Night Mode Color / B&W / AUTO / Ext.
Control Parameters Menu OSD (With an optional OSD cable control)
Flicker Less ON/OFF
Dynamic Noise Reduction 2D
Motion Detection ON / OFF (24x16 Zones)
Privacy Mask ON / OFF (8 programmable mosaic zones)
Video: Peak Inverse Blocking Voltage: VPIB = 100V; Peak Pulse Current:
Surge Protector
Clamping Voltage: 16.8KA(1Time)/8.4KA (2Times) @ 8/20μs (1 Time);
Waterproof IP 67
Infrared Luminary 36pieces Ø8 IR-LED
Transmission Distance Video / Power up 300 meters (Cat. 5 or above)
Ipp=44A; Clamping Voltage: 10V @ Ipp= 5A
Power: Max. Energy: 3.6J (@10/1000μ);
Insulation Resistance: ≧10000MΩ
Power Consumption
Operation Temperature -10°C ~ 50°C; Humidity 20% ~ 80% RH
Dimension/Weight 105 (W) x 200 (H) x 255 (L) mm / 0.9Kg (Including bracket)
IR ON: DC 24V/190mA max, IR OFF: DC 24V/25mA.
2
Standard Accessories
↲
r
¾ PRX-120VP Video/Power Balun for DVR site x 1 pc.
¾ Screws to fix camera housing x 4 pcs.
¾ L-Wrench screwdriver x 1 pc
¾ Bracket sticker label x 1 pc
¾ Menu x 1 pc
¾ OSD controller cable x 1 pc (Optional)
Setup the camera parameters by OSD menu
Plug OSD cable (Option) on the socket cable and there is a button on OSD cable for further configures camera parameters.
Press button to
enable OSD or Ente
Enter the camera configuration OSD menu Press button
Enter the configuration page of an option Press button
If you want to ……
Move to the sub-menu you want
Change setting
Press
Push to↑ / ↓direction
Push button to ← / → direction
For options with
SETUP MENU OPTIONS
LENS AUTO↲ TYPE DC/VIDEO
SHUTTER/AGC AUTO↲ HIGH LUMINANCE MODE SHUT+AUTO IRIS
MANUAL↲ MODE SHUT+AGC
WHITE BAL ATW↲ SPEED 0~255
BACKLIGHT OFF/BLC/HLC
PICT ADJUST
ATR O FF
DAY/NIGHT AUTO↲ BURST ON/OFF
↲, press the button“↲ ”(Enter)to enter their respective setting pages.
MODE OPEN/AUTO/CLOSE
SPEED 0~255
MANUAL
/ AUTO IRIS
BRIGHTNESS 0~255
LOW LUMINANCE MODE AGC/OFF
BRIGHTNESS ×0.25 / ×0.50 / 0.75 / ×1.00
SHUTTER 1/50
AGC 6.00/12.00/18.00/24.00/30.00/36.00/42.00/44.80
DELAY CNT 0~255
ATW FRAME ×0.50 / ×1.00 / ×1.50 / ×2.00
ENVIRONMENT INDOOR / OUTDOOR
PUSH
USER1↲ /
USER2
ANTI CR
MANUAL↲ LEVEL 015~056
PUSH LOCK
MIRROR OFF/ON
ON↲ LUMINANCE LOW / MID / HIGH
COLOR
B-GAIN / R-GAIN 0~255
↲
BRIGHTNESS / CONTRAST
/SHARPNESS /HUE / GAIN
CONTRAST LOW / MIDLOW / MID / MIDHIGH / HIGH
DELAY CNT /
DAY→NIGHT/NIGHT→DAY
0~255
0~255
3
B / W
↲
↲
EXT1 & EXT2 for external trigger signal. (Enable EXT1 for IR LED optimizer function )
PRIVACY OFF
ON AREA SEL 1/4、2/4、3/4、4/4
MOTION DET OFF
ON↲ DETECT SENSE 0~127
NR
CAMERAID OFF/ON↲
SYNC INT
LANGUAGE ENGLISH /日本語 / DEUTSCH / FRANCAIS / PYCCKNŇ / PORTUGUÊS / ESPAŇ OL
CAMERA RESET
BURST ON/OFF
IR OPTIMIZER ON/OFF
MODE AUTO/CENTER
LEVEL 0~31
TOP/BOTTOM 0~244
LEFT/RIGHT 0~378
COLOR 0~8
TRANSP 0.00/ 0.50/ 0.75 /1.00
MOSAIC ON / OFF
BLOCK DISP OFF /ON / ENABLE↲
MONITOR AREA ON/OFF
AREA SEL 1/4、2/4、3/4、4/4
TOP / BOTTOM 0~288
LEFT / RIGHT 0~468
NR MODE Y/C ; Y ; C ; OFF
Sub-menu Brief Description
SUB-MENU DESCRIPTION
LENS Select and set the type of your lens: DC Driver, Video Driver or board lens.
SHUTTER / AGC Select “AUTO” to allow the camera to act automatically when the light condition of the
environment changes. Select “MANUAL” to fix the shutter and AGC modes of the camera
no matter how the light condition of the environment changes.
WHITE BAL Process the current image to retain color balance over a color temperature range.
BACKLIGHT Adjust the image to compensate for an area that is overpowered by brightness because of
excessive light.
“BLC” is to automatically adjust the level of the light to show more details in the dark
environment. And the “HLC” is to mask extremely bright areas.
PICT ADJUST Adjust the color of the pictures in, for example, brightness, contrast, sharpness and hue.
ATR D-WDR to increase the image recognized capability of the overexposed and dark areas.
PRIVACY Mask areas that should be not visible.
DAY / NIGHT Set the night surveillance mode to color or B/W.
NR Reduce noise by separating luminance (Y) and chrominance (C) settings.
CAMERA ID Set the title of the camera.
LANGUAGE Select the language of the menu on-screen display.
CAMERA RESET
↲ to restore all settings to their factory default values.
Press
Tel : 886-3-5103001 Fax: 886-3-510002
Email: support@i-view.com.tw
Website: www.i-view.com.tw
4
Loading...