I-View Ethernet PoE User Manual

Ethernet over Coax Extender Installation Guide V1.0

 Packing Checklist:

Carefully unpack and check the package box if the following items are included:

¾ EOC-110V x 1 ea

¾ EOC-100V x 1 ea

¾ DC12V power adapter x 1 ea

¾ Menu x 1 pc

 Product Feature:

¾ Transmits up to distances of 300 meters ⁄ 660 feet.

¾ Supports any 10/100M Ethernet device, including IP cameras.

¾ Fully transparent to the network.

¾ Easy to install, no IP and MAC address configuration required

 Product Overview:

EOC-110V

Power LED (yellow)

Indicate the power status

Female BNC Connector

Attaches to 75Ω coax cable.

Female BNC Connector

Attaches to 75Ω coax cable.

Power Jack

Plug DC12V power adapter

RJ-45 Connector

Attaches to Cat5 or Cat6 patch cable.

EOC-110V

 Product Application Diagram

 Installation Notes:

¾ Please use 75 Ohm coaxial cable and BNC connector for the data transmission.

RJ-45 Connector

Attaches to Cat5 or Cat6 patch cable

¾ Please use less than 2 meters Category 5, 5E or 6 UTP patch cable to connect IP camera or Switch HUB.

¾ Some IP cameras built in pigtail cable which with none standard Cat. 5 UTP cable, it will cause the shorter

transmission distance or no communication. Please confirm this issue to your IP camera vendor.

¾ Please measure the coaxial wire distance, use only transceivers that are designed for that distance.

¾ To avoid the terminator problem, before connecting the LAN cable from EOC device to switching HUB, please

connect the coax cable between both EOC devices and the LAN cable between IP camera & EOC device first.

¾ The quality of coaxial cable will reduce or increase the transmission distance. The EOC-100Kit is tested for use

with RG-59U 75 Ohm copper based 20AWG coaxial cable.

¾ That is free from damage as in cuts, breaks, or cracks to the outer covering and insulated shielding which may

compromise the signal conductivity of the cable.

¾ For safety, DO NOT put EOC signals in the same conduit as high-voltage wiring.

For more specific information regarding wire types, gauges, and proper installation techniques, please call Tech

Support at 886-3-5103001 or email to [e-mail]

 Installation Steps:

1. Connect the unit's RJ45 Ethernet jack to the IP camera using a standard Cat5 or Cat6 patch cable and unit's BNC

socket to a 75 ohm coax cable with BNC connector.

2. Plug the DC 12V power adapter to the EOC-100V Ethernet over Coax extender.

3. Connect the unit's (Which on the HUB site) BNC socket to a 75 ohm coax cable with BNC connector, then plug

the a standard Cat5 or Cat6 patch cable to the unit’s RJ45 Ethernet jack to the Switching HUB.

4. In order to get better transmission distance, the Ethernet patch cable should be a standard Cat5 or Cat6 cable and

less than 2 meters

.

 Troubleshooting:

The following table describes some of the symptoms, probable causes and possible solutions

Problem Possible Cause

Hub LED indicator is

OK, but no video

9 Check IP camera and unit device connections.

9 Check coax cable condition and BNC connectors is 75 Ohm.

9 Check cable that cable distances do not exceed EOC-110V operating distance.

9 Check the built in jumper cable of IP camera used non- standard Cat. 5 cables.

9 Check that the camera is powered.

Network lost

9 Check network switch termination(s) & link status.

9 Check network routing table(s).

9 Confer with site Network Administrator.

 Specification:

Item \Model EOC-100V EOC-110V

Ethernet

Coaxial

Power Consumption

Dimension /Weight

Environment

Speed: 10/100Base-T full-duplex

Distance: 300 meters (Typ.)@ full rate via RG59U coax cable

DC 12V / 50mA None

100 x 55 x 34 mm / 140g 55 x 25 x 25 mm / 60g

Operation: 0℃to 50℃; 20% ~ 85% non-condensing

Phone: [phone] Fax: [phone]

Connector: RJ-45

Connector: BNC 75 Ohm

Cable: Any 75 Ohm coax cable

Bandwidth: 100M bits/Second

Mail: [e-mail]