I-View Ethernet User Manual

Ethernet over Coax Extender Installation Guide V1.0

 EOC-110Kit Product Overview:

The package including:

¾ EOC-110V x 2 ea

¾ Menu x 1 pc

EOC-110V

Female BNC Connector

Attaches to 75Ω coax cable.

 Product Feature:

¾ Transmits up to distances of 200 meters ⁄ 660 feet.

¾ Supports any 10/100M Ethernet device, including IP cameras.

¾ Fully transparent to the network.

¾ Easy to install, no IP and MAC address configuration required

 Product Application Diagram

RJ-45 Connector

Attaches to Cat5 or Cat6 patch cable.

 Installation Notes:

1. Please use 75 Ohm coaxial cable and BNC connector for the data transmission.

2. Please use less than 2 meters

3. Some IP cameras built in pigtail cable which with none standard Cat. 5 UTP cable, it will cause the shorter

transmission distance or no communication. Please confirm this issue to your IP camera vendor.

4. Please measure the coaxial wire distance, use only transceivers that are designed for that distance.

5. To avoid the terminator problem, before connecting the LAN cable from EOC-110V to HUB, please connect the

coax cable between both EOC-110V devices and the LAN cable between IP camera & EOC-110V first.

6. The quality of coaxial cable will reduce or increase the transmission distance. The EOC-110Kit is tested for use

with RG59U 75 Ohm copper based 20AWG coaxial cable.

7. That is free from damage as in cuts, breaks, or cracks to the outer covering and insulated shielding which may

compromise the signal conductivity of the cable.

8. For safety, DO NOT put EOC signals in the same conduit as high-voltage wiring.

For more specific information regarding wire types, gauges, and proper installation techniques, please call Tech

Support at 886-3-5103001 or email to [e-mail]

Category 5, 5E or 6 UTP patch cable to connect IP camera or Switch HUB.

 Installation Steps:

1. Connect the EOC-110V unit's RJ45 Ethernet jack to the IP camera using a standard Cat5 or Cat6 patch cable and

EOC-110V unit's BNC socket to a 75 ohm coax cable with BNC connector.

2. Connect the EOC-110V unit's (Which on the HUB site) BNC socket to a 75 ohm coax cable with BNC connector,

then plug the a standard Cat5 or Cat6 patch cable to EOC-110V unit’s RJ45 Ethernet jack to the Switching HUB.

3. In order to get better transmission distance, the Ethernet patch cable should be a standard Cat5 or Cat6 cable and

less than 2 meters

.

 Troubleshooting:

The following table describes some of the symptoms, probable causes and possible solutions

Problem Possible Cause

Hub LED

indicator is OK,

but no video

Network lost

9 Check IP camera and EOC-110V device connections.

9 Check coax cable condition and BNC connectors is 75 Ohm.

9 Check cable that cable distances do not exceed EOC-110V operating distance.

9 Check the built in jumper cable of IP camera used non- standard Cat. 5 cables.

9 Check network switch termination(s) & link status.

9 Check network routing table(s).

9 Confer with site Network Administrator.

 Specification:

Item \Model EOC-110V

Ethernet

Connector: RJ-45

Speed: 10/100Base-T full-duplex

Connector: BNC 75 Ohm

Coaxial

Size/Weight

Environment

Cable: Any 75 Ohm coax cable

Distance: 200 meters (Typ.)@ full rate via RG59U coax cable

Bandwidth: 100M bits/Second

55 x 25 x 25 mm / 60g

Operation: -20℃to 70℃; 20% ~ 85% non-condensing

Phone: [phone] Fax: [phone]

Email: [e-mail]