Ethernet/PoE Extender over UTP Cable Installation Guide V1.2
Product Overview:
1. Extend: RJ45 Female Connector (No LED) converter allows 10/100 Base-T Ethernet and PoE power to be
transmitted using Cat. 5 or better UTP cable with 4 pair wires.
2. Link: The LED indicates the cable link status. The LED will be on after 10 seconds when first connection is
success; Off: No connection.
3. Pwr: The LED indicates the power status. On: Power on; Off: No power.
4. Ethernet/PoE: RJ45 connector, attaches to POE IP Camera or Hub via Cat5, 5e, 6 or 7 patch cables.
5. Eth: The LED indicates the communication status. Flash: Communicate with Traffic; Off: No connection.
6. Power jack: Plug DC power adapter to for PoE source when PoE Hub cannot provide enough power source.
7. PoE: The LED indicates the PoE power status. On: PoE power is provided; Off: No PoE power.
1
3
2
5
4
6
1
2
7
3
5
4
6
Packing Checklist:
Check the package box the following items are included:
EPOC-131VAJ (Or EOPC-131PSJ) * 1 ea;
Menu * 1 pc.
Installation Steps:
IP camera end
1. Connect the IP camera RJ45 connector to the 10/100BaseT Ethernet port of EPOC-131PSJ using a standard
Cat5/6 cable of maximum 100 m (328 feet) in length.
2. Connect one end of the long UTP cable such as Cat.5, 5e, 6, or 7 cable to the RJ45 (No light) connector of
EPOC-131PSJ.
3. When the IP camera and EPOC-131PSJ cannot receive power through the UTP cable, even through using the
POE+ Hub or plug DC56V power adapter for EPOC-131VAJ . Plug the DC48V power adapter into the
EPOC-131PSJ will be needed at this end. Please refer to “Power Distance VS. Cable Impedance” table.
Switch Hub end
1. Connect the PoE switch Hub RJ45 connector to the 10/100BaseT Ethernet port of EPOC-131VAJ using a
standard Cat5/6 cable of maximum 100 m (328 feet) in length.
2. Connect one end of the long UTP cable such as Cat.5, 5e, 6, or 7 cable to the RJ45 (No light) of EPOC-131VAJ .
3. When the IP camera and EPOC-131PSJ cannot receive power through the Wire cable, please change the POE+
Hub or plug DC56V power adapter to EPOC-131VAJ .
1
Product Application Diagram
The Ethernet over UTP Cable system allows the Star topology or Daisy-chained communication. It supports
virtually any type of Cat. UTP wire, including such as Cat.5, 5e, 6, or 7 cable. And different wire types can be
concatenated together, as needed.
To avoid the interference signal, we strongly recommend using the Cat. STP cable with metal RJ45
Connector for Ethernet/PoE signal transmission when there are more 16 pcs EPOC-131VAJ install at the
same Hub site.
Daisy Chain
Plug DC56V power adapter to EPOC-131VAJ or DC48V to EPOC-131PSJ when the IP Camera cannot receive
Point to Point Topology
The IP camera and EPOC-131PSJ cannot receive power through the UTP cable. Please do as below:
1. POE+ Hub or plug DC56V power adapter for EPOC-131VAJ .
Plug DC48V power adapter to EPOC-131PSJ when the EPOC-131PSJ cannot receive power.
2. Plug the DC48V power adapter into the EPOC-131PSJ will be needed at this end. Please refer to “Power
Wattage VS. Cable Distance” table or visit www.i-view.com.tw
2
Power Wattage VS. Cable Distance
Data Rate VS. Cable distance
LED Function table
Name Color Status Function
Pwr Yel low On Power is on
Eth Green Flashing Communication is OK with Traffic
Link Green On Connection is OK; (It take 10 sec. for LED on)
PoE Green On PoE is offering
Off Power is off
Off No communication
Off No connection
Off No PoE offer
3
Specification:
ITEM \ M O DEL EPOC-131VA J EPOC-131PSJ EPOC-131PSJ-O
Ethernet
Connector RJ-45 RJ-45 RJ-45
Connectivity 10/100/1000 Base-T auto-negotiation, auto MDI / MDX crossover
Wire type Cat5 or better
Distance Up to 328 feet (100m)
Cable Link
Connector RJ-45
Type Receiver (Hub Site) Transmitter (Camera Site)
Wire type Cat.5, Cat.5e, Cat.6, Cat.7 UTP Cable
Distance Up to 600 Meters (1980 feet)
Topology Supports Star, Daisy-Chain, or any combination
Encryption 128-bit AES
Latency 3 ms
Bandwidth Total network bandwidth 150 Mbps; with dynamic bandwidth allocation
Power
Power Source
1
1
PoE Hub; DC44～
56V
PoE or DC48V PoE or DC48V
Power Output PoE (RJ-45 via4 pairs
25W PoE (RJ45); (50W Option)
cable)
Physical
Waterproof None None IP 66
Dimensions (mm) 100 x 55 x 34 100 x 55 x 34 128 x 102 x 36
Weight 140g 140g 310g
LEDs
Status indicators
Cable link
Ethernet Power
Ethernet link/activity
Cable link
Ethernet Power
PoE Connection
Ethernet link/activity
Cable link
Ethernet Power
PoE Connection
Ethernet link/activity
Environment
Temperature
Humidity 20% ~ 85% non-condensing
Power consumption ≤ 2W
Transient immunity 20µS x5 3,000A, 6,000V; ESD 20KV, 200pF
1. Distance and number of devices supported may be lower due to power supply capacity and wire voltage-drop. The bandwidth is
dynamically allocated (shared based on traffic), and decreases with wire distance.
Operation: 0℃to 50℃/ 14℉ to 122℉
Phone: 886-3-510-3001 Fax: 886-3-510-3002
4
Mail: support@i-view.com.tw
5
Loading...