I-View DM-650-F36 User Manual

3

1

3

2

2

3

7

 DM-650-F36 Dome Camera Function Description:

1.) Lens: 3.6 mm board Lens. Provide 6mm/8mm/12mm as alternative choices.

2.) Screw: To fix the housing body and cover.

3.) Mounting Hole: There are 3 holes to fix the camera housing on the ceiling.

4.) Gutter: To fix the wire cable of camera.

5.) LED: Power indicator, Green LED On: Power on. Green LED Off: No Power. Yellow LED:

V1.0

4

65

Reserve

6.) RJ-45 connector: To transmit Power and Video signals via UTP cable. Please refer to the RJ45 pin

assignment.

7.) Socket cable: To Connect OSD control cable (Optional) for camera parameters setup.

 PTT-140VPM Function Description: (On DVR site)

PTT-140VPM RJ45 Pin Assignment

Power Plug

Power Indicator

1.) Power Plug: Connect DC 12V-18V power source input and provide power output for camera.

2.) BNC Cable: For video output to DVR.

3.) RJ-45 connectors: To transmit Power and Video signals via UTP cable.

4.) LED: Power indicator, LED On: Power on. LED Off: Not enough power or No Power.

Male BNC

Please refer to the pin assignment.

5.) RJ-45 pin Assignment: Connect the 4-pair UTP cable between DVR site and camera end for video/power

transmission.

WARNING: This camera MUST use DC 12V-18V power adapter for power transmission.

1

 Installation Warning:

1. Please DO NOT USE SHIELD TWISTED PAIR WIRE. This will cause severe degradation on distance

performance and reduce the inherent interference immunity.

2. Please DO NOT have “bridge-taps” or loading coils in installation.

3. If the phone company provides the cable runs between buildings, make sure it’s “dry copper”.

4. Due to near-end cross talk, don’t send a transmitted and a received signal in the same wire bundle.

5. For safety, DO NOT put UTP cable in the same conduit as high-voltage wiring.

 Installation Notes:

1. Please use point-to-point Unshielded Twisted Pair wire, 24-16 AWG, Category 2, 3, 4, 5, or 6.

2. Please measure the wire distance, Use only transceivers that are designed for that distance.

3. Please make sure the pair of wires carrying the video signal is sent as a twisted pair (e.g. the

Blue-white/White-blue wires twisted together as a pair), not a “split-pair” (e.g. blue-white conductor, part of

one pair / orange-white conductor, part of another pair).

 Specification:

DM-650-F36

Image Device Video

Image Device: 1/3“ SONY EXview HAD CCD II (Effio-E)

Effective Picture Elements: PAL: 1024(H)x596 (V);

NTSC: 1028(H)x508(V)

Video Characteristic

S/N Ratio: More than 50dB (AGC Off)

Shutter Speed Control: AUTO (1/50(60) ~ 1/100,000 sec.)

Gamma Characteristic: 0.45

Sync. System: Internal

Wide Dynamic Range: ATR Digital WD (ATR: Adaptive

Tone-curve Reproduction)

Lens

Lens: F3.6 mm Board Lens

Illumination

Minimum Illumination: Color: 0.03Lux@F1.0

Transmission Distance

Transmit Video / Power up to 300 meters via Cat. 5 or better

Horizontal Resolution: Color: 650TVL, B/W: 700TVL

Video System: NTSC/PAL (Optional)

Video Output: 1Vp-p output with RJ-45 connector; BNC

type connector (Option)

OSD Menu Setting

Flicker Less: ON/OFF

Gain Control: Auto (4 steps)

Dynamic Noise Reduction: 2D

Motion Detection: ON / OFF (24x16 Zones)

Day/Night Mode: Color / B&W / AUTO / Ext.

Back Light Compensation: HLC / BLC / OFF

Privacy Mask: ON / OFF (8 programmable mosaic zones)

Control Parameters: Menu OSD (With an optional OSD

cable control)

White Balance: ATW / PUSH / USER define / ANTI CR /

MANUAL / PUSH LOCK

UTP cable

Housing

Vandal resistant housing with 3-Axis bracket

Dimension/Weight

ψ106mm x 69 mm (H) / 0.38 Kg

Operation

Power Consumption: DC 12V/50mA.

Operation: Temperature -10°C ~ 50°C; Humidity 20% ~

80% RH

2



↲

r

Standard Accessories

¾ PTT-140VP Video/Power Balun for DVR site x 1 pc.

¾ Screws to fix camera housing x 3 pcs;

¾ L-Wrench screwdriver x 1 pcs; Menu x 1pcs.

¾ OSD controller cable x 1 pc (Optional)

 Setup the camera parameters by OSD menu

Plug OSD cable (Option) on the socket cable and there is a button on OSD cable for further configures camera

Press button to

enable OSD or Ente

parameters.

Enter the camera configuration OSD menu Press button

Enter the configuration page of an option Press button

If you want to ……

Move to the sub-menu you want

Change setting

Press

Push button to↑ / ↓direction

Push button to ← / → direction

For options with

SETUP MENU OPTIONS

LENS AUTO↲ TYPE DC/VIDEO

SHUTTER/AGC AUTO↲ HIGH LUMINANCE MODE SHUT+AUTO IRIS

MANUAL↲ MODE SHUT+AGC

WHITE BAL ATW↲ SPEED 0~255

BACKLIGHT OFF/BLC/HLC
PICT ADJUST

ATR O FF

DAY/NIGHT AUTO↲ BURST ON/OFF

↲, press the button“↲ ”(Enter)to enter their respective setting pages.

MODE OPEN/AUTO/CLOSE
SPEED 0~255

MANUAL

/ AUTO IRIS

BRIGHTNESS 0~255

LOW LUMINANCE MODE AGC/OFF

BRIGHTNESS ×0.25 / ×0.50 / 0.75 / ×1.00

SHUTTER 1/50
AGC 6.00/12.00/18.00/24.00/30.00/36.00/42.00/44.80

DELAY CNT 0~255
ATW FRAME ×0.50 / ×1.00 / ×1.50 / ×2.00

ENVIRONMENT INDOOR / OUTDOOR
PUSH
USER1↲ /
USER2
ANTI CR
MANUAL↲ LEVEL 015~056
PUSH LOCK

MIRROR OFF/ON

ON↲ LUMINANCE LOW / MID / HIGH

COLOR

B-GAIN / R-GAIN 0~255

↲

BRIGHTNESS / CONTRAST

/SHARPNESS /HUE / GAIN

CONTRAST LOW / MIDLOW / MID / MIDHIGH / HIGH

DELAY CNT /

DAY→NIGHT/NIGHT→DAY

3

0~255

0~255

B / W

↲

↲

EXT1 & EXT2 for external trigger signal.

PRIVACY OFF

ON AREA SEL 1/4、2/4、3/4、4/4

MOTION DET OFF

ON↲ DETECT SENSE 0~127

NR
CAMERA ID OFF/ON↲
SYNC INT
LANGUAGE ENGLISH /日本語 / DEUTSCH / FRANCAIS / PYCCKNŇ / PORTUGUÊS / ESPAŇOL
CAMERA RESET

BURST ON/OFF

IR OPTIMIZER ON/OFF

MODE AUTO/CENTER

LEVEL 0~31

TOP/BOTTOM 0~244

LEFT/RIGHT 0~378
COLOR 0~8
TRANSP 0.00/ 0.50/ 0.75 /1.00
MOSAIC ON / OFF

BLOCK DISP OFF /ON / ENABLE↲
MONITOR AREA ON/OFF
AREA SEL 1/4、2/4、3/4、4/4

TOP / BOTTOM 0~288

LEFT / RIGHT 0~468

NR MODE Y/C ; Y ; C ; OFF

 Sub-menu Brief Description

SUB-MENU DESCRIPTION

LENS Select and set the type of your lens: DC Driver, Video Driver or board lens.

SHUTTER / AGC Select “AUTO” to allow the camera to act automatically when the light condition of the

environment changes. Select “MANUAL” to fix the shutter and AGC modes of the camera

no matter how the light condition of the environment changes.

WHITE BAL Process the current image to retain color balance over a color temperature range.

BACKLIGHT Adjust the image to compensate for an area that is overpowered by brightness because of

excessive light.

“BLC” is to automatically adjust the level of the light to show more details in the dark

environment. And the “HLC” is to mask extremely bright areas.

PICT ADJUST Adjust the color of the pictures in, for example, brightness, contrast, sharpness and hue.

ATR D-WDR to increase the image recognized capability of the overexposed and dark areas.

PRIVACY Mask areas that should be not visible.

DAY / NIGHT Set the night surveillance mode to color or B/W.

NR Reduce noise by separating luminance (Y) and chrominance (C) settings.

CAMERA ID Set the title of the camera.

LANGUAGE Select the language of the menu on-screen display.

CAMERA RESET

↲ to restore all settings to their factory default values.

Press

Phone: [phone] Fax: [phone]
Email: [e-mail]

4