I-View DM-650-F0409 User Manual

3

1

3

2

 DM-650-F0409 Dome Camera Function Description:

1.) Lens: 4-9mm Vari-Focal Lens. Provide 2.8-12mm Vari-Focal Lens as alternative choices.

2.) Screw: Screw the camera housing.

3.) Mounting Hole: There are 3 holes to fix the camera housing on the ceiling.

4.) Gutter: To fix the wire cable of camera.

5.) LED: Power indicator, Green LED On: Power on. Green LED Off: No Power. Yellow LED: Reserve.

4

3

V1.0

7

6

5

6.) RJ-45 connector: To transmit Power and Video signals via UTP cable. Please refer to the RJ45 pin assignment.

7.) Socket cable: To Connect OSD control cable (Optional) for camera parameters setup.

 PTT-140VPM Function Description: (On DVR site)

PTT-140VPM RJ45 Pin Assignment

Power Plug

Power Indicator

1.) Power Plug: Connect DC 12V-18V power source input and provide power output for camera.

2.) BNC Cable: For video output to DVR.

3.) RJ-45 connectors: To transmit Power and Video signals via UTP cable.

4.) LED: Power indicator, LED On: Power on. LED Off: Not enough power or No Power.

5.) RJ-45 pin Assignment: Connect the 4-pair UTP cable between DVR site and camera end for video/power

transmission.

Male BNC

Please refer to the pin assignment.

WARNING: This camera MUST use DC 12V-18V power adapter for power transmission.

1

 Installation Warning:

1. Please DO NOT USE SHIELD TWISTED PAIR WIRE. This will cause severe degradation on distance

performance and reduce the inherent interference immunity.

2. Please DO NOT have “bridge-taps” or loading coils in installation.

3. If the phone company provides the cable runs between buildings, make sure it’s “dry copper”.

4. Due to near-end cross talk, don’t send a transmitted and a received signal in the same wire bundle.

5. For safety, DO NOT put UTP cable in the same conduit as high-voltage wiring.

 Installation Notes:

1. Please use point-to-point Unshielded Twisted Pair wire, 24-16 AWG, Category 2, 3, 4, 5, or 6.

2. Please measure the wire distance, Use only transceivers that are designed for that distance.

3. Please make sure the pair of wires carrying the video signal is sent as a twisted pair (e.g. the

Blue-white/White-blue wires twisted together as a pair), not a “split-pair” (e.g. blue-white conductor, part of

one pair / orange-white conductor, part of another pair).

 Specification:

DM-650-F0409

Image Device Video

Image Device: 1/3“ SONY EXview HAD CCD II (Effio-E)

Effective Picture Elements: PAL: 1024(H)x596 (V); NTSC:

1028(H)x508(V)

Video Characteristic

S/N Ratio: More than 50dB (AGC Off)

Shutter Speed Control: AUTO (1/50(60) ~ 1/100,000 sec.)

Gamma Characteristic: 0.45

Sync. System: Internal

Wide Dynamic Range: ATR Digital WD (ATR: Adaptive

Tone-curve Reproduction)

Lens

Lens: 4-9 mm Vari-focus Lens; (2.8-12mm Lens Optional)

Illumination

Minimum Illumination: Color: 0.03Lux@F1.0

Transmission Distance

Transmit Video / Power up to 300 meters via Cat. 5 or better

UTP cable

Horizontal Resolution: Color: 650TVL, B/W: 700TVL

Video System: NTSC/PAL (Optional)

Video Output: 1Vp-p output with RJ-45 connector;

BNC type connector (Option)

OSD Menu Setting

Flicker Less: ON/OFF

Gain Control: Auto (4 steps)

Dynamic Noise Reduction: 2D

Motion Detection: ON / OFF (24x16 Zones)

Day/Night Mode: Color / B&W / AUTO / Ext.

Back Light Compensation: HLC / BLC / OFF

Privacy Mask: ON / OFF (8 programmable mosaic

zones)

Control Parameters: Menu OSD (With an optional OSD

cable control)

White Balance: ATW / PUSH / USER define / ANTI CR

/ MANUAL / PUSH LOCK

Operation

Housing

Vandal resistant housing with 3-Axis bracket

Dimension/Weight

ψ105mm x 88 mm (H) / 0.42Kg

Power Consumption: DC 12V/50mA.

Operation: Temperature -10°C ~ 50°C; Humidity 20% ~

80% RH

2