I-View DM-5MIPN User Manual

5/2-MEGAPIXELS NETWORK CAMERA

DM-5M/2MIPN/2MIPS-F04 USER MENU

Version: V1.3
Doc. No.: 103021601

Safety information

This symbol indicates that dangerous voltage consisting a risk of electric shock is

present within this unit.

This exclamation point symbol is intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the literature accompanying the

appliance.

WARNING

 To prevent damage that may result in fire or electric shock hazard, do not expose this

appliance to rain or moisture.

 To prevent injury, this apparatus must be securely attached to the floor / wall in accordance

with the installation instructions.

WARNING

1. Be sure to use only the standard adapter that is specified in the specification sheet using any

other adapter could cause fire, electric shock, or damage to the product.

2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,

electric shock, or damage to the product.

3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause

the abnormal heat generation or fire.

4. Securely plug the power cord into the power receptacle, insecure connection may cause fire.

5. When installing the camera, fasten it securely and firmly. The fall of camera may cause

personal injury.

2

6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers

filled with water on top of the camera. Doing so may cause personal injury due to fire,

electric shock, or falling objects.

7. If any unusual smells or smoke come from the unit, stop using the product. In such case,

immediately disconnect the power source and contact the service center. Continued use in

such a condition may cause fire or electric shock.

8. If this product fails to operate normally, contact the nearest service center and never

disassemble or modify this product in any way. (I-View is not liable for problems caused by

unauthorized modifications or attempted repair.)

9. When cleaning, do not spray water directly onto parts of the product. Doing so may cause

fire or electric shock.

CAUTION

 Do not drop objects on the product or apply strong shock to it. Keep away from a location

subject to excessive vibration or magnetic interference.

 Do not install in a location subject to high temperature (over 50°C), low temperature (below

-10°C), or high humidity. Doing so may cause fire or electric shock.

 If you want to relocate the already installed product, be sure to turn off the power and then

move or reinstall it.

 Remove the power plug from the outlet when then there is a lightning. Neglecting to do so

may cause fire or damage to the product.

 Keep out of direct sunlight and heat radiation sources. It may cause fire.

 Install it in a place with good ventilation.

 Avoid aiming the camera directly towards extremely bright objects such as sun, as this may

damage the CCD image sensor.

 Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,

such as vases, shall be placed on the apparatus.

 The Mains plug is used as a disconnect device and shall stay readily operable at any time.

 Do not expose the camera to radioactivity. Radioactivity exposure may damage the CCD.

3

IMPORTANT SAFETY INSTRUCTIONS

 Read these instructions.

 Keep these instructions.

 Heed all warnings.

 Follow all instructions.

 Do not use this apparatus near water.

 Clean only with dry cloth.

 Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

 Do not install near any heat sources such as radiators, heat registers, or other apparatus

(Including amplifiers) that produce heat.

 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug

has two blades with one wider than the other. A grounding type plug has two blades and a

third grounding prong. The wide blade or the third prong is provided for your safety. If the

provided plug does not fit into your outlet, consult an electrician for replacement of the

obsolete outlet.

 Protect the power cord from being walked on or pinched particularly at plugs, convenience

receptacles, and the point where they exit from the apparatus.

 Only use attachments/accessories specified by the manufacturer.

 Use only with cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the apparatus.

 Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus

combination to avoid injury from tip-over.

 Refer all servicing to qualified service personnel. Servicing is required when the

apparatus has been damaged in any way, such as power supply cord or plug is damaged,

liquid has been spilled or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has been dropped.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,

such as vases, shall be placed on the apparatus.

4

SAFETY INFORMATION

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following

conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received including interference that may cause

undesired operation.

CAUTION

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own

expense.

Correct Disposal of This Product (Waste Electrical & Electronic Equipment)

This marking on the product, accessories or literature indicates that the product and its

electronic accessories should not be disposed of with other household waste at the end of their

working life. To prevent possible harm to the environment or human health from uncontrolled

waste disposal, please separate these items from other types of waste and recycle them

responsibly to promote the sustainable reuse of material resources.

Household users should contact either the retailer where they purchased this product, or their

local government office, for details of where and how they can take these items for

environmentally safe recycling.

Business users should contact their supplier and check the terms and

conditions of the purchase contract. This product and its electronic

accessories should not be mixed with other commercial wastes for disposal.

5

About This Guide

Conventions used in this guide

To make sure that you perform certain tasks properly, take note of the following symbols to use

throughout this manual.

WARNING: Information to prevent injury to yourself when trying to complete a task.

CAUTION: Information to prevent damage to the components when trying to complete a

task.

IMPORTANT: Information that you must follow to complete a task.

NOTE: Tips and additional information to aid in completing a task.

Trademark

I-View, e-Witness, @-Witness Pro, u-Witness XP, x-Witness, FreeView Pro, AnyCam, PDAVirw

and MobileView are registered trademarks of I-View Communication Inc.

Microsoft, Windows 95, 98, ME, Windows2000, XP, Vista, 7 and 8 are registered trademarks of

Microsoft Corporation. All other trademarks are the property of their respective holders.

Customer Support

If technical problems arise with the use of our products in which you and your vendor cannot

resolve, please try the following: If you have an Internet connection, visit the I-View website

http://www.i-view.com.tw (Taiwan) for any software or product updates, or email to

[e-mail] (Taiwan) or Tel: [phone] Fax: [phone] (Taiwan). We

are dedicated to providing the highest quality support. E-mailing our tech support will give you

the chance to document each of the above items in a very clear and concise manner and will give

our support team a chance to document any problems and respond with thoroughly researched

answers.

6

Table of Contents

Chapter 1. Introduction ---------------------------------------------------------------------------------------- 8

1-1. Highlights of your new Network IP Camera ------------------------------------------------ 8

1-2. Product Specification --------------------------------------------------------------------------- 9

1-3. Packaging Contents --------------------------------------------------------------------------- 18

1-4. Product Dimension ---------------------------------------------------------------------------- 18

1-5. Product Parts Description -------------------------------------------------------------------- 19

Chapter 2. Camera Installation------------------------------------------------------------------------------ 20

2-1. Ceiling Mount installation ------------------------------------------------------------------- 20

Chapter 3. Running IP Camera by Witness Pro NVR software. ------------------------------------- 22

3-1. Network Deployment ------------------------------------------------------------------------- 22

3-2. Install Witness Pro NVR software ---------------------------------------------------------- 23

3-3. Setting IP camera for Witness Pro NVR software ---------------------------------------- 25

Chapter 4. Running IP Camera by I.E. Browser -------------------------------------------------------- 28

4-1. Install ActiveX Plug-in on I.E. Browser --------------------------------------------------- 29

4-2. The Function Description of Live Window ----------------------------------------------- 32

4-3. The Network setup Function Description-------------------------------------------------- 34

Chapter 5. Troubleshooting ---------------------------------------------------------------------------------- 55

7

Chapter 1. Introduction

1-1. Highlights of your new Network IP Camera

Congratulates on purchasing this high-resolution 5M pixels network IP Camera! This IP

Camera provides 5M pixels high-resolution video quality, with its advanced megapixel lens; you

can view remote images in more detail than conventional close-circuit cameras.

Other highlights of this network IP Camera include:

 Onvif compliant.

 Built-in 802.3af compliant PoE

 Built in 3.6 mm Megapiexls Lens.

 Vandal resistant and 3-Axis bracket design.

 Up to 5-Megapixels (2592 x1920) resoultion.

 Support motion detection and video output.

 Built-in surge protector.

 Removable IR-cut filter for Day & Night function.

 H.264 and MJPEG multiple simultaneous streams.

 Support Wide Dynamic Range and Privacy mask function.

 Ultra Low Compress Rate(ULCR) technology: LESS storage space, SAME video quality.

 ROI (Region of Interest) encoding enhances the quality of specified images.

8

1-2. Product Specification

DM-5MIPN Series

System

Platform: TI DM368 SoC CPU; Linux Embedded O.S.

Image Device

1/2.5" 5 M pixels (2592x 1944 pixels) progressive CMOS sensor.

Video Setting

Compression: Video: 0.1M ~ 12M bits/sec (CBR/VBR/LBR configurable) H.264

HP/MP/BP, M-JPEG; Audio: G.711μ-low/a-low Codec

Resolution: Main Streaming: 2592×1920, 2048×1536, 1920×1080, 1280×720. Sub

streaming: 320×288, 320*240

Frame Rate: 5-Mega: 10 fps; 3-Mega: 20 fps; 1080p: 30 fps @ H.264/M-JPEG Mode; Frame

rate can be adjustable by user.

Streaming: Multi-Stream H.264 Base/Main/High Profile and Motion JPEG video streaming

Control: Brightness, Contrast, Saturation, Sharpness, Exposure, Motion detection, Mirror,

Shutter, Privacy mask, Flickerless, Noise reduction, IRIS, AES, AWB, AGC , BL C,

D- WDR, RO I, Au dio gain, Alarm in /ou t

Color: 0.5 Lux 1/F1.2 B/W: 0.3 Lux .

D- WDR: 70 dB

Overlay: Text / Time Stamp

Audio Setting

μ

-Low/ a-Low G.711 audio encoding and decoding; 2-way audio.

External Microphone input; Speaker output.

2Vp-p audio input and audio output with 600Ω impedance.

Network

Protocol: HTTP, HTTPS, TCP/ IP, IPv4, IPv6, UDP, SMTP, FTP, DHCP, DDNS, NTP,

DNS, SNMP, RTSP, RTP/RTCP, Bonjour, PPPoE, QoS, UPnP, IGMP; uPnP and 802.1x.

Interface: 10BASE-T/100 BASE-TX; Wi-Fi (Via USB optional)

Compatible: Onvif compliant.

9

I/O Port

Au dio in (2Vp-p) ; Au dio out (30 mW/ 600Ω); DC in, RJ-45 ( LED indicates

power/linking status), Audio in x1; Audio out x1; DC power in, RJ-45.

Surge Protector

Video: P eak In vers e B locking Vol tage : VPIB = 1 00V; Peak P ulse Cu rrent:

Ip p=44 A; Clampin g Voltag e: 10V @ Ipp= 5A .

Po wer: Ma ximu m E ner gy: 3. 6J @10/ 100 0 µs; Cla mping Volt a ge:

16 .8KA(1- Ti me) /8.4 KA( 2-Tim es) @8/20µs (1 Time ); Insu lation Res istance:

10 000MΩ.

≧

Lens & IR Cut

Lens: f= 4mm; 6mm, 8mm, 12mm/ F1.8 (Optional) (DM-5MIPN-F04/06/08/12 ).

IR Cut: Built on removable IR-cut filter for day & night function.

Storage

Micro SD slot for SD/SDHC card storage; Support Pre-recording and Post recording; Network

failed start recording on SD card, Backup/Restore to device configuration file, Backup, Upload

data to FTP/SMTP sever.

Management

Time management: Manual Time Setting; Time Server and NTP support; Real Time Clock.

Event management: Events triggered by motion detection or sensor configured by schedule.

Event notification: Notify to FTP, email, Samba server or Digital output triggered.

Update: Support Firmware update.

Browse

I.E. 7.0 above; Safair Browser, Fire Fox and Chrome V3.0 above with plug in.

Housing

Vandal resistant and 3-Axis bracket design.

Dimension/Weight

ø

117mm x 92 mm (H) / 0.35Kg

Operation

10

Power: Maximum 3 W; PoE IEEE 802.3af Class 3; DC12V

Tempe rat ure : Temperature -10°C ~ 50°C; Humidity 20% ~ 80% RH.

DM-2MIPN Series

System

Platform: TI DM365 SoC CPU; Linux Embedded O.S.

Image Device

1/3" 1.3 M pixels (1280x 960 pixels) progressive CMOS sensor.

Video Setting

Compression: Video: 0.1M ~ 8M bits/sec (CBR/VBR/LBR configurable) H.264 HP/MP/BP,

M-JPEG; Audio: G.711μ-low/a-low Codec

Resolution: Main Streaming: 1920 x1080 (Software enhance), 1280×960, 1280×720.

Sub streaming: 320×288, 320*240

Frame Rate: 2-Mega: 20 fps (Software enhance); 1.3Mega: 30 fps @ H.264/M-JPEG Mode;

Frame rate can be adjustable by user.

Streaming: Multi-Stream H.264 Base/Main/High Profile and Motion JPEG video streaming

Control: Brightness, Contrast, Saturation, Sharpness, Exposure, Motion detection, Mirror,

Shutter, Privacy mask, Flickerless, Noise reduction, IRIS, AES, AWB, AGC , BL C,

D- WDR, RO I, Au dio gain, Alarm in /ou t

Color: 0.1 Lux 1/F1.2 B/W: 0.05 Lux .

D- WDR: 83 .5d B

Overlay: Text / Time Stamp

Audio Setting

μ

-Low/ a-Low G.711 audio encoding and decoding; 2-way audio.

External Microphone input; Speaker output.

2Vp-p audio input and audio output with 600Ω impedance.

Network

Protocol: HTTP, HTTPS, TCP/ IP, IPv4, IPv6, UDP, SMTP, FTP, DHCP, DDNS, NTP,

DNS, SNMP, RTSP, RTP/RTCP, Bonjour, PPPoE, QoS, UPnP, IGMP; uPnP and 802.1x.

11

Interface: 10BASE-T/100 BASE-TX; Wi-Fi (Via USB optional)

Compatible: Onvif compliant.

I/O Port

Au dio in (2Vp-p) ; Au dio out (30 mW/ 600Ω); Alar m i n x1 ; Al arm out x1 , DC

in , RJ-45 ( LED indicates power /linking status).

Surge Protector

Video: P eak In vers e B locking Vol tage : VPIB = 1 00V; Peak P ulse Cu rrent:

Ip p=44 A; Clampin g Voltag e: 10V @ Ipp= 5A .

Po wer: Ma ximu m E ner gy: 3. 6J @10/ 100 0 µs; Cla mping Volt a ge:

16 .8KA(1- Ti me) /8.4 KA( 2-Tim es) @8/20µs (1 Time ); Insu lation Res istance:

10 000MΩ.

≧

Lens & IR Cut

Lens: f= 4mm; 6mm, 8mm, 12mm/ F1.8 (Optional) (DM-2MIPN-F04/06/08/12).

IR Cut: Built on removable IR-cut filter for day & night function.

Storage

Micro SD slot for SD/SDHC card storage; Support Pre-recording and Post recording; Network

failed start recording on SD card, Backup/Restore to device configuration file, Backup, Upload

data to FTP/SMTP sever.

Management

Time management: Manual Time Setting; Time Server and NTP support; Real Time Clock.

Event management: Events triggered by motion detection or sensor configured by schedule.

Event notification: Notify to FTP, email, Samba server or Digital output triggered.

Update: Support Firmware update.

Browse

I.E. 7.0 above; Safair Browser, Fire Fox and Chrome V3.0 above with plug in.

Housing

Vandal resistant and 3-Axis bracket design.

Dimension/Weight

12

ø

117mm x 92 mm (H) / 0.35Kg

Operation

Power: Maximum 2.5 W; PoE IEEE 802.3af Class 3; DV12V

Tempe rat ure : Temperature -10°C ~ 50°C; Humidity 20% ~ 80% RH.

DM-2MIPS Series

System

Platform: TI DM368 SoC CPU; Linux Embedded O.S.

Image Device

1/3" 2M pixels (1920X1080 pixels) SONY Exmor progressive CMOS sensor.

Video Setting

Compression: Video: 0.1M ~ 12M bits/sec (CBR/VBR/LBR configurable) H.264

HP/MP/BP, M-JPEG; Audio: G.711 μ-low/a-low Codec

Resolution: Main Streaming: 1920×1080. Sub streaming: 320×288, 320*240

Frame Rate: 1080p: 30 fps @ H.264/M-JPEG Mode; Frame rate can be adjustable by user.

Streaming: Multi-Stream H.264 Base/Main/High Profile and Motion JPEG video streaming

Control: Brightness, Contrast, Saturation, Sharpness, Exposure, Motion detection, Mirror,

Shutter, Privacy mask, Flickerless, Noise reduction, IRIS, AES, AWB, AGC , BL C,

D- WDR, RO I, Au dio gain, Alarm in /ou t

Color: 0.3 Lux 1/F1.2 B/W: 0.1 Lux .

D- WDR: 76 dB

Overlay: Text / Time Stamp

Audio Setting

μ

-Low/ a-Low G.711 audio encoding and decoding; 2-way audio.

External Microphone input; Speaker output.

2Vp-p audio input and audio output with 600Ω impedance.

Network

Protocol: HTTP, HTTPS, TCP/ IP, IPv4, IPv6, UDP, SMTP, FTP, DHCP, DDNS, NTP,

DNS, SNMP, RTSP, RTP/RTCP, Bonjour, PPPoE, QoS, UPnP, IGMP; uPnP and 802.1x.

13

Interface: 10BASE-T/100 BASE-TX; Wi-Fi (Via USB optional)

Compatible: Onvif compliant.

I/O Port

Au dio in (2Vp-p) ; Au dio out (30 mW/ 600Ω), DC in, RJ-45 ( LED indicates power

/linking status).

Surge Protector

Video: P eak In vers e B locking Vol tage : VPIB = 1 00V; Peak P ulse Cu rrent:

Ip p=44 A; Clampin g Voltag e: 10V @ Ipp= 5A .

Po wer: Ma ximu m E ner gy: 3. 6J @10/ 100 0 µs; Cla mping Volt a ge:

16 .8KA(1- Ti me) /8.4 KA( 2-Tim es) @8/20µs (1 Time ); Insu lation Res istance:

10 000MΩ.

≧

Lens & IR Cut

Lens: f= 4mm; 6mm, 8mm, 12mm/ F1.8 (Optional) (DM-5MIPN-F04 /06/08/12).

IR Cut: Built on removable IR-cut filter for day & night function.

IR Illuminators: 3 p ieces 2 W third gener ati on arra y LE D Illuminators.

Storage

Micro SD slot for SD/SDHC card storage; Support Pre-recording and Post recording; Network

failed start recording on SD card, Backup/Restore to device configuration file, Backup, Upload

data to FTP/SMTP sever.

Management

Time management: Manual Time Setting; Time Server and NTP support; Real Time Clock.

Event management: Events triggered by motion detection or sensor configured by schedule.

Event notification: Notify to FTP, email, Samba server or Digital output triggered.

Update: Support Firmware update.

Browse

I.E. 7.0 above; Safair Browser, Fire Fox and Chrome V3.0 above with plug in.

Housing

Vandal resistant and 3-Axis bracket design.

14

Dimension/Weight

ø

117mm x 92 mm (H) / 0.35Kg

Operation

Power: Maximum 3 W; PoE IEEE 802.3af Class 3; DV12V

Tempe rat ure : Temperature -10°C ~ 50°C; Humidity 20% ~ 80% RH.

DM-3MIPW Series

System

Platform: TI DM368 SoC CPU; Linux Embedded O.S.

Image Device

1/3" 3 M pixels (2048x 1536 pixels) progressive CMOS sensor.

Video Setting

Compression: Video: 0.1M ~ 12M bits/sec (CBR/VBR/LBR configurable) H.264

HP/MP/BP, M-JPEG; Audio: G.711μ-low/a-low Codec

Resolution: Main Streaming: 2048×1536, 1920×1080, 1280×720.

Sub streaming: 320×288, 320*240

Frame Rate: 3-Mega: 20 fps; 1080p: 30 fps @ H.264/M-JPEG Mode; Frame rate can be

adjustable by user.

Streaming: Multi-Stream H.264 Base/Main/High Profile and Motion JPEG video streaming

Control: Brightness, Contrast, Saturation, Sharpness, Exposure, Motion detection, Mirror,

Shutter, Privacy mask, Flickerless, Noise reduction, IRIS, AES, AWB, AGC , BL C,

D- WDR, RO I, Au dio gain, Alarm in /ou t

Color: 0.2 Lux 1/F1.2 B/W: 0.1 Lux .

WD R: 83.5 dB

Overlay: Text / Time Stamp

Audio Setting

μ

-Low/ A-Low G.711 audio encoding and decoding; 2-way audio.

External Microphone input; Speaker output.

15

2Vp-p audio input and audio output with 600Ω impedance.

Network

Protocol: HTTP, HTTPS, TCP/ IP, IPv4, IPv6, UDP, SMTP, FTP, DHCP, DDNS, NTP,

DNS, SNMP, RTSP, RTP/RTCP, Bonjour, PPPoE, QoS, UPnP, IGMP; uPnP and 802.1x.

Interface: 10BASE-T/100 BASE-TX; Wi-Fi (Via USB optional)

Compatible: Onvif compliant.

I/O Port

Au dio in (2Vp-p) ; Au dio out (30 mW/ 600Ω), DC in, RJ-45 ( LED indicates power

/linking status).

Surge Protector

Video: P eak In vers e B locking Vol tage : VPIB = 1 00V; Peak P ulse Cu rrent:

Ip p=44 A; Clampin g Voltag e: 10V @ Ipp= 5A .

Po wer: Ma ximu m E ner gy: 3. 6J @10/ 100 0 µs; Cla mping Volt a ge:

16 .8KA(1- Ti me) /8.4 KA( 2-Tim es) @8/20µs (1 Time ); Insu lation Res istance:

10 000MΩ.

≧

Lens & IR Cut

Lens: f=4mm; 6mm, 8mm, 12mm/ F1.8 (Optional) (DM-3MIPW-F04 /06/08/12).

IR Cut: Built on removable IR-cut filter for day & night function.

Storage

Micro SD slot for SD/SDHC card storage; Support Pre-recording and Post recording; Network

failed start recording on SD card, Backup/Restore to device configuration file, Backup, Upload

data to FTP/SMTP sever.

Management

Time management: Manual Time Setting; Time Server and NTP support; Real Time Clock.

Event management: Events triggered by motion detection or sensor configured by schedule.

Event notification: Notify to FTP, email, Samba server or Digital output triggered.

Update: Support Firmware update.

Browse

16

I.E. 7.0 above; Safair Browser, Fire Fox and Chrome V3.0 above with plug in.

Housing

Vandal resistant and 3-Axis bracket design.

Dimension/Weight

ø

117mm x 92 mm (H) / 0.35Kg

Operation

Power: Maximum 3W; PoE IEEE 802.3af Class 3; DV12V

Tempe rat ure : Temperature -10°C ~ 50°C; Humidity 20% ~ 80% RH.

17