IVEX-PTZ User Manual
Explosion proof Security Camera
Be sure to read this manual before installing or using the product.
02
Contents
Address IP : 192.168.1.2
ID/Password : root / pass
If you install a camera not manufactured by Indus
Vision, the default IP and ID / Password may be
changed.
1. Safety Instruction
2. Typical Features
3. Components
4. Part Names
5. Installation
3
4
5
5
6
5-1. Separating a Front cover from Camera Housing
5-2. Separation Between Housing Cover and Cable
5-3. Assembling Camera into the Housing
5-4. Main Board Configuration
5-5. Wiring Main Board Connection in the Housing
5-6. Reassembling After Built-in a Camera
5-7. Cabling from Entry
5-8. Cable Configuration
6. Functions and Operation
7. Checklist Before Installation
8. Specifications
9-1. Dimension
9-2. Dimension
6
7
8
9
10
11
12
13
14
15
16
17
18
03
1. Safety Instruction
1. Install and use this system after reading these safety instruction thoroughly.
2. Keep these instructions after reading.
3. On installing this product, use all kinds of screws and bolts made of stainless steel to
asten the mount to outdoor surfaces and have to use explosion proof certified
accessories for installing.
4. Only use replacing parts recommended by the manufacturer.
5. The maximum ambient temperature range is -40℃ to 67℃ (-40℉ ~ 152.6℉).
6. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
7. The weight of the product is heavy, so be careful when lifting the product. It is highly
recommended to wear non-slip gloves during installation.
8. Receiving this product before installation, please check the system and working according
to the “chapter 7. checklist before installation”
CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER(OR BACK). NO
USER SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE
PRERSONNEL
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING : This symbol indicates that dangerous voltage constituting a risk
of electric shock is present within this unit.
WARNING : Do not open when an explosive atmosphere may be present.
WARNING : To reduce the risk of ignition of hazardous atmospheres,
disconnect the equipment from the supply circuit before
opening. Keep assembly tightly closed when operating.
WARNING : To reduce the risk of ignition of hazardous atmosphere, all
conduit runs must have sealing fitting or cable gland placed
within 3/4”of the enclosure.
WARNING : Do not open when an explosive atmosphere may be present.
04
2. Key Features
IVEX-PTZ Type
• Ex Certification : IECEx / ATEX / KCs / NEPSI / CE / FCC / KC
• Ex Grade : Ex d IIC T6 Gb. Zone 1 & 2, Ex tb IIIC T85˚C Db. Zone 21 & 22
• AISI 316L Stainless Steel Construction
• IP67 Protection Degree
• Germanium Glass, Protection Grid(PTZ-40/41) / Fully Tempered Glass
• Operating Temperature : -40°C ~ +67°C
• Operating Humidity : Less than 90%RH
• Pan/Tilt Travel Range : ±360°(Continuous) / ±90°
• Pan/Tilt Travel Speed : 0.5 ~ 20° / Sec
• Preset : Can store 58 locations
• Tour : Can store 8 locations
• Cable Outlet : 1 EA(NPT 3/4”)
• Option : Wiper / Fan / Heater / Window Demister
• Support RS-485 Protocol
• ONVIF Support
This product has two driving parts to
rotate 360 degrees left/right and 180 degrees
up/down, Camera is built in so that you can
check the image. Sunshield is installed to protect
the product from radiant heat or rain
05
3. Components
1. Camera 2. Sun-shield 3. User’s Manual
4. Part Names
1. Camera Housing Cover
2. Camera Housing Body
3. Tilt Housing
(2)
(1)
4. Accessories 5. SMPS(Power supply) 6. Connecting Cable
(3)
(4)
(6)
4. Pan Base Housing
5. Cable Entry, NPT 3/4 inch
6. Sun-shield
(5)
06
5. Installation
5-1. Separating a Front Cover From Camera Housing
1 2
3 4
Sunshield Remove the top two M5xL10 bolts to
Separate the sunshield from the housing body.
Remove all eight M5xL20 bolts from the front of
the housing cover using a hexagonal wrench(4mm).
(A) Turn two bolts M4xL40 in the accessory pack
to the clockwise with a balance then the screw
bolts push the cover from the housing.
Separate the front cover from the housing body
carefully.
M5 X L10
(Spring Washer + Flat Washer) 2set
M5 X L20
(A)
(A)
M4 X L40
(B)
When you separate the cables,
please memory
the directions of the cables and
then reassemble
in reverse when you connect with
the cables.
07
5. Installation
5-2. Separation Between Housing Cover and Cable
2 3
4
1
30pin
9pin
When the front cover of housing is separated, please be careful for damage camera, main board,
wiper motor and remove the each cable from the main board, camera carefully.
Remove the 30pin jack from the main board. Remove the 9pin jacks from the main
board.
When the CVBS Input and the Camera
Input(RJ-45 connector) jack are disconnected from
The main board, the housing cover is completely
Separated from the housing body.
CVBS Input
Camera Input
08
5. Installation
5-3. Assembling Camera into the Housing
1 2
3 4
Assemble the camera to the slide bracket of the
Camera with a supplied M6 x L6 bolt
Assemble the sliding bracket having a
Camera loosely with supplied four H3 x L8 bolts to
A temporary position on the main bracket
After sticking a lens of the camera to the front
Tempered glass, tighten the main bracket of the
camera with four M4 x L10 bolts
M6 x L6(Spring Washer) 1set
H3 x L8
(Spring Washer) 4set
Camera
Main Bracket
Mount Bracket for BOX Camera
MAIN BOARD
09
5. Installation
5-4. Main Board Configuration
MAIN BOARD
MAIN BOARD
No Name No Name
1 30pin Cable Harness 9 Camera Input(RJ-45 Connector)
2 Wiper Board 10 #1 Alarm output
3 Heater(12V) 11 #3 Alarm output
4 12V DC Input 12 Heater(12V)
5 24V DV Input 13 Pan(12V)
6 12V DC Output 14 MCU Data Input
7 CVBS Input 15 RS-485
8 Alarm Input
MAIN BOARD
10
5. Installation
5-5. Wiring Main Board Connection in the Housing
Wiper Power
Wiper Board
• CAUTION : The black Cable(+) and the white Cable(-) are for the Camera power
and data Communication.
11
5. Installation
5-6. Reassembling After Built-in a Camera
1 2
3 4
30pin
9pin
5
Align the 30pin, 9pin, and 7pin Jacks on the
Camera to the Right with your Hand, and Slide the
Housing Cover with the new Camera All the way to
the Second Picture so that it Does not Catch on the
Wiper Shaft.
Connect the 30pin Jack to the Mainboard While
Pushing.
Connect the 9pin Cable Jacks to the Main
Board as Shown in # 2.
If all Cables are Connected, put the Housing Cover
Inside the Camera and Finish it.
Finally, Recombining the Page 6 "5-1 Camera Housing and the Cover Separated“
in Reverse Order.
12
5. Installation
5-7. Cabling from Entry
[Note]
[C]
[B]
[A]
(M8 x 1.25P x 20L) x 4 set
1. (A) Please check the status thread of the nut if there is dusts or regular condition for hex.
stainless steel bolt or wrench bolt(M8X1.25Px20L) and fix it with washer/spring-washer to keep
locking the bolts on the product.
2. According to the environment, it can be changed brackets
(to be Wall Mount Type or Pedestal Type), (refer to the“Ch.9 Dimension”)
3. (B) Check the thread of the sealing fittings if there is dust or good status for using.
4. (C) Connect a nipple with thread of cable entry and tighten flexible cable in the sealing fitting.
In here, all cables have to come out though sealing fitting and all of sealing fitting, cable grand,
And flexible cable must be certified the explosion proof standards.
5. Please refer the [Note] for external earth grounding.
NPT 3/4”-14
Nipple(including)
NPT 3/4“-14
Sealing fitting
(Non-including)
Ex-proof
Flexible cable
(Non-including)
NPT 3/4“-14 Cable Grand
Ex-proof Sealing fitting
Filter Finishing material Cable
1. It Has to Use 4㎟ Over of Dimension
for External Grounding Cable.
2. Use to Hex. Wrench Bolt (M4 x 0.7P)
for ISO4762 to Earth Ground.
3. Use Flat-Washer/Spring-Washer for
Unlocking Bolts.
External
grounding
MAIN BOARD
13
5. Installation
5-8. Cable Configuration
3M ± 0.2
Wire Color Function Description
Red
Black
Power Input
(DC 24V)
+
-
*Black
(UTP)
HD Video/Data RJ45
Black/Brown
Red/Orange
Control Data
RS485 Data +
RS485 Data -
Yellow Analog Video out BNC
Power(DC24V)
Data(RS-485)
Network(RJ45)
Analog Video(BNC)
14
6. Functions & Operations
Function Preset No How to set
PRESET 1-58 ex) Press 5 + Preset (Preset Go To)
How to preset
ex) Position PT location and then press
No. 5 + Preset-Key for 3 seconds (Preset Save)
Set Washer
pump location
59
Position Nozzle and then press
No. 59 + Preset-key for 3 seconds (Preset Save)
Auto Scan 61-64
Travel Scan 1 location to Scan 2 location repeatedly
ex) Press No. 61 + Preset-key (Preset Go To)
Auto Scan1 ~ 4
Start Set
61, 63, 65, 67
ex) Position Start PT and then press
No. 61 + Preset-key for 3 sec. (Preset Save)
Auto Scan1 ~ 4
End Set
62, 64, 66, 68
ex) Position End PT and then press
No. 62 + Preset-key for 3 sec. (Preset Save)
Tour 71-78
Travel to saved Preset 1~4 (5~8…29~32) locations (8 Groups)
ex) Press No. 71 + Preset-key (Preset Go To)
Wiper On 85 Start Wiper 85 + Preset (Preset Go To)
Wiper Off 69 Stop Wiper 69 + Preset (Preset Go To)
Infrared On 86
Turn on the Infrared LED (LED Light On)
86 + Preset (Preset Go To)
Infrared Off 79
Turn off the Infrared LED (LED Light Off)
79 + Preset (Preset Go To)
Washer
Pump On
88
Activate Washer Pump (Move to location of Preset No. 59 and
operate wiper
for 6 sec, washer for 3 sec and then go back to the previous
location.)
88 + Preset (Preset Go To)
Rum Home 91 Move to Home Position 91 + Preset (Preset Go To)
Pan/Tilt Reversal 93 Reversal operating of Pan/Tilt 93 + Preset (Preset Go To)
Default mode 99
Go to factory default
Press No. 99 + Preset-key for 3 sec (Preset Save)
System Reboot 100 Power On/Off 100 + Preset (Preset Go To)
Set ID Address 101~255
Set ID Address
Ex1.) Set No.1 ID Address : Press No. 101 + Preset-
key for 3 sec.
(Preset Save) /
Ex2.) Set No. 120 ID Address : Press No. 220 + Preset-key for 3
sec (Preset Save)
15
7. Checklist before installation
1. When you receive, please check the product according to the following checklist before installation
in the site and if you find the normal for all, please install the goods.
2. Please be noted it could be charged for some service if you don’t remind the checklist.
(Please contact to info@indusvision.co.kr or following phone number, if you have troubles
out of check list.)
INDUSVISION Inc. / CS Technical Team : +82-32-624-0750
No. Check Point Check
1 Please Remove the Fixing Foam After Installing and Fixing the Device.
2 After Removing the Fixing Foam, Power on the Unit.
3 Please Remove the Multi Cable Holder After Fixing the Device.
4
Do not turn the tilt part(Top/Bottom) more than 180 degrees from the front.
lt nay cause malfunctioz
5
Please use the power supply(SMPS) that is supplied from factory or your
provider and be careful to connect specification of the power supply.
(DC24V / AC220V / AC110V)
6 Please connect exactly polarity(+/-) of the Data Cable(RS-485).
7
Please check the initializing moving as the following:
- Pan(Left/Right) Moving Check/Tilt(top/bottom) Moving Check
8
Please Check the Video Quality by Connecting Video Cable(BNC Connector) to
DVR or Monitor.
9
After Connecting CAT. 5 Cable(RJ-45 Jack) to Network Port, Please Check the
Video, Data Control and Other Conditions in the Normal Network Condition.
10
Please Set the Protocol and Baud Rates as Following :
- Protocol/Baud Rate : Pelco-D / 9600 bps
- ID Address : No. 1(Default)
11
In IP Network Camera, Please Set and Save Exactly PELCO-D, 9600 Bps and
ID Address in the Supplied CMS or NVR Software.
12
Check WIPER Operation(Left/Right)
(Press No.85 and Preset-key : ON, Press No. 69 and Preset-Key : OFF)
13 Please Check the Pan / Tilt / Zoom / Video / Data Communication Finally
Fixing Foam
Multi Cable
Holder
16
8. Specifications
CAMERA SPECIFICATION
Model IVEX-PTZ Series
Ex Certification IECEx / ATEX / KCs / NEPSI / CE/ FCC / KC
Ex Grade
Ex d IIC T6 Gb, Zone 1 & 2
Ex tb IIIC T85˚C Db. Zone 21 & 22
Material AISI 316L Stainless Steel
Window Material
Germanium Glass, Protection Grid(PTZ-40/41) /
Fully Tempered Glass
Protection Degree IP67
Operating Temperature -40°C ~ +67°C
Operating Humidity Less than 90%RH
Communication RS-485
Pan/Tilt Travel Range 360˚(Continuous) / ±90˚
Pan/Tilt Travel Speed 0.5˚ ~ 20˚/Sec(Max. 40˚/Sec)
Lens(PTZ-30) F= 6mm ~ 216mm / F1.5(wide) ~ F4.8(tele)
Cable Outlet 1EA(NPT 3/4”)
Wiper/Fan/Heater
Window Defroster
Option
Power Consumption Approx. 150 W
Input Power DC 24V, 50/60Hz, 110 ~ 230VAC, 50/60Hz(Option)
Dimension 516(W) x 460(H) x 380(L)mm
Weight Approx. 30 kg
17
9-1. Dimension
DIMENSION
Unit : mm
18
9-2. Dimension
IVEX-PTZR-WB
Unit : mm
IVEX-PTZR-PD
Unit : mm
Loading...