Ives 620, 702 User Manual
Installation Instructions
602 and 702 Series Surface Continuous Hinges
!
CAUTION
Please follow the installation instructions carefully.
Not doing so may result in improper installation and
void the manufacturers guarantee.
INSTALLATION NOTES
Reinforcing and Rivet Nuts:
No reinforcing is necessary except on heavy doors.
Reinforcement and rivet nuts are required in the frame and
door when door weight exceeds 300 pounds. Maximum
door weight is 600 pounds.
Pairs of Doors with Mullions:
If the mullion is between the doors, treat as a single door
installation. If the mullion is behind the doors, treat as a
double door installation.
Note: Before proceeding, check to be sure that hinge is proper
size. Height of hinge should be 7/8 LESS than opening height.
See other side of page for cutting instructions.
1
Mount hinge to frame.
Place frame leaf of hinge on face
A.
of frame so that there is 1/8 gap
between top of hinge and
underside of frame header, and
1/16 gap between edge of the
frame and the center line of the
hinge barrel. Check to be sure
hinge leaf is square to frame with
1/16 gap from edge of frame to
centerline of hinge barrel the full
length of the hinge.
1/8
Frame
1/16
829171-00
2
Mount hinge to door.
IMPORTANT NOTE: FOR ALL UL
FIRE LABEL DOORS, 1/4-20 X
1-3/4 STEEL THROUGH BOLTS
MUST BE USED FOR FASTENING
THE HINGE TO THE DOOR.
Move door into opening and place
A.
door leaf of hinge on face of door so
that top of door is flush with top of
hinge and center line of hinge barrel
is 1/16 from edge of door.
NOTE: There should be 1/8 clearance between the top of
the door and the bottom of the frame header and 1/8
clearance between the edge of the door and frame. An
angle block, jack or shims will be helpful in positioning the
door properly. Check to be sure hinge leaf is square to
door with 1/16 gap from edge of frame to centerline of
hinge barrel the full length of the hinge.
B.
With hinge and door held firmly and accurately in place, use
1/4-20 x 3/4 self drilling screws through cover clips and
screw into door through mounting holes in door leaf. Cover
clips should be located at top and bottom mounting holes,
and equally spaced along the length of the door leaf.
Install remaining 1/4-20 x 3/4 self drilling screws through
mounting holes in door leaf.
ALL HOLE LOCATIONS ON HINGE LEAF MUST BE FASTENED TO
DOOR FOR PROPER OPERATION. FAILURE TO INSTALL ALL
FASTENERS WILL VOID WARRANTY AND UL FIRE LABEL LISTINGS.
3
Check for proper operation.
A.
Close door and check for
proper operation and
clearances.
Frame
Edge of
door
1/16
1/8
1/8
With hinge held firmly and accurately
B.
to frame, place 1/4-20 x 3/4 self drilling
screws through cover clips and screw into frame through
mounting holes in hinge leaf. Cover clips should be located
at the top and bottom mounting holes, and equally spaced
along the length of the frame leaf.
Install remaining 1/4-20 x 3/4 self drilling screws through
C.
mounting holes in frame leaf.
ALL HOLE LOCATIONS ON HINGE LEAF MUST BE FASTENED TO
FRAME FOR PROPER OPERATION. FAILURE TO INSTALL ALL
FASTENERS WILL VOID WARRANTY AND UL FIRE LABEL LISTINGS.
NOTE: FOR THIN METAL FRAMES (18 GAUGE OR THINNER)
THE USE OF RIVET NUT STYLE FASTENERS IS RECOMMENDED.
829171-00(0)
© 2006 Ingersoll-Rand Company Limited
1/8
4
Mount screw covers.
A.
After door has been checked for proper operation and all
mounting screws have been tightened, engage short leg of
cover to barrel side of clip.
B.
Tap cover onto outside clip with rubber
mallet so that long leg of cover sets
against frame of door surface.
DO NOT DAMAGE COVER.
Instructions for Cutting Hinge
1
Determine hinge height.
A.
Measure height of opening
from finished floor to
underside of door frame
header.
Hinge height is height of
B.
opening MINUS 7/8.
Height of
opening
MINUS 7/8
2
Mark hinge for cutting.
4
Shorten hinge pin 3/4.
Using center punch or heavy nail, tap on cut surface of
A.
hinge pin to remove top hinge tip (save tip for step 5).
Expose 1 of hinge pin. Measure and mark 3/4 from end
B.
of pin.
DOUBLE CHECK MEASUREMENT BEFORE CUTTING.
Cut pin at mark.
C.
Save tip
A.
Determine which end of
hinge will be the TOP
using door and frame as
a guide.
B.
Open hinge to expose
back of hinge (holes
are NOT countersunk).
C.
Measure hinge height
calculated in step 1
from top of hinge.
D.
Using square, mark a line
on back of both hinge
leaves and the barrel.
DOUBLE CHECK MEASUREMENT BEFORE CUTTING!
NOTE:
Cut end of hinge must be used as BOTTOM OF HINGE ONLY!
3
Cut hinge.
Fold hinge so that cut line is visible.
A.
Starting on barrel, cut through
B.
entire hinge along line.
Debur all cut edges with file.
C.
Opening
height
minus
7/8
Cutting line
Top
Bottom
/4
3
5
Insert top and bottom tip.
Tap hinge pin back into barrel.
A.
Tap hinge pin tips (retained from step 3 and 4) firmly
B.
into top and bottom of barrel until shoulder sets
squarely on barrel.
NOTE: Both tips MUST BE INSTALLED to hold hinge
pin in position.
Use center punch or heavy gauge
D.
nail on pin in short cut off portion of
hinge to remove hinge tip. SAVE
HINGE TIP for use in step 5.
Save tip
6
Important Note:
If more than 6 is cut from bottom of hinge, additional
mounting holes will be required on bottom of hinge. Use
cut off piece of hinge to mark and prepare hole locations
on bottom of hinge.
Page 2 of 2 829171-00(0)
Loading...