1
NP-5xxA SERIES User Manual
Release Date _ Revision
Apr. 2013 V1.0
NP-5xxxA SERIES User Manual
2
Warning!___________________________________
This equipment generates, uses and can radiate radio frequency energy and if not installed and
used in accordance with the instructions manual, it may cause interference to radio communications.
It has been tested and found to comply with the limits for a Class A computing device pursuant to
FCC Rules, which are designed to provide reasonable protection against such interference when
operated in a commercial environment. Operation of this equipment in a residential area is likely
to cause interference in which case the user at his own expense will be required to take whatever
measures may be required to correct the interference.
Electric Shock Hazard – Do not operate the machine with its back cover removed. There are
dangerous high voltages inside.
Disclaimer
This information in this document is subject to change without notice. In no event shall Aplex
Technology Inc. be liable for damages of any kind, whether incidental or consequential, arising
from either the use or misuse of information in this document or in any related materials.
NP-5xxxA SERIES User Manual
3
Packing List
Accessories (as ticked) included in this package are:
□ AC power cable
□ Driver & manual CD disc
□ Other.___________________(please specify)
Safety Precautions
Follow the messages below to prevent your systems from damage:
◆ Avoid your system from static electricity on all occasions.
◆ Prevent electric shock. Don‘t touch any components of this card when the card is
power-on. Always disconnect power when the system is not in use.
◆ Disconnect power when you change any hardware devices. For instance, when you
connect a jumper or install any cards, a surge of power may damage the electronic
components or the whole system.
NP-5xxxA SERIES User Manual
4
Table of Contents______________________
Warning!…………………………………………………………………………….……..….2
Disclaimer………………………………………………………………….…………………2
Packing List…………………………………………………………………………………..3
Safety Precautions…………………………………………………………………………..3
Chapter 1 Getting Started
1.1 Specifications……………………………………..….……………………..6
1.2 Dimensions………………………………...………………………….......7
1.3 Brief Description………………………………………………….………10
1.4 Installation of HDD…………………………………………………………11
Chapter 2 Hardware
2.1 Mainboard………………..…….……………………………………..…..15
2.2 Installations…….………………….……………………………………...18
2.3 Jumpers Setting and Connectors........................................................19
Chapter 3 BIOS Setup
3.1 Operations after POST Screen.............................................................28
3.2 BIOS SETUP UTILITY..........................................................................29
3.3 Main Settings…....................................................................................29
3.4 Advanced Settings............................................................................... 31
3.5 Chipset Settings................................................................................... 37
3.6 Boot Settings....................................................................................... 41
3.7 Security Settings.................................................................................. 44
3.8 Save and Exist Settings....................................................................... 45
3.9 Exit Options..........................................................................................51
Chapter 4 Installation of Drivers
4.1 Intel Chipset Driver.…………………………...…………………………54
4.2 Intel Graphics Media Accelerator Driver...……………………………..57
4.3 Intel (R) Network Adapter……..………………………………………….60
4.4 Realtek ALC662 HD Audio Driver Installation…….………….…………62
Chapter 5 Touch Screen Installation
5.2 Windows 2000/XP USB Driver Installation for PenMount 6000Series.64
5.1.1 Installing Software (Resistive Touch).................................................64
NP-5xxxA SERIES User Manual
5
5.1.2 Installing Software (Projected Capacitive)..........................................69
5.2.1 Software Functions(Resistive Touch).................................................74
5.2.2 Software Functions(Projected Capacitive)………….………………….85
Figures
Figure 1.1:Dimensions of NP-507A…………………………………..…....7
Figure 1.2:Dimensions of NP-508A…………………………………..…....8
Figure 1.3:Dimensions of NP-512A…………………………………….8
Figure 1.3:Dimensions of NP-515A…………………………………….9
Figure 1.4: Front View of NP-5xxA SERIES………………………………...10
Figure 1.5: Rear View of NP-507A/NP-508A……………………..10
Figure 1.5: Rear View of NP-512A/NP-515A……………………..11
Figure 2.1: Mainboard Dimensions…………………………………..…….....17
Figure 2.2: Jumpers and Connectors Location_ Board Top………………...18
Figure 2.3: Jumpers and Connectors Location_ Board Bottom…………....19
NP-5xxxA SERIES User Manual
6
Chapter 1 System
1.1 Specifications
NP-507A NP-508A NP-512A NP-515A
System
CPU Intel Atom Cedar View N2600 1.6GHz Dual Core Processors
System Chipset Intel NM10
System Memory Onboard DDR3 2GB 800 MHz
IO Port
USB 2 x USB 2.0 type A, USB4/5
Serial/Parallel 1 x RS-232/422/485 DB-9, COM1, Default RS-232
Audio 1 x Line out phone jack
LAN 2 x GbE RJ-45
Power 3 pins terminal block connector, DC Power input
Storage Space
HDD 1 x 2.5” SATA 2 half size 1 x 2.5” SATA 2
Movable device 1 x Internal SD slot 1 x Internal SD slot
Expansion
On board
expansion bus
Display
Display Type 7” TFT-LCD 8” TFT-LCD 12.1” TFT-LCD 15” TFT-LCD
Max. Resolution 800x480 WinCE
1 x RS-232 DB-9, COM2
1 x Mini-PCIe half size
800x600 800x600 1024x768
640x480
Max. Color 262K 16.2M 16.2M 16.2M
Luminance
(cd/m²)
View
angle(H°/V°)
Touch screen
Type Resistive Touch / Projected Capacitive Touch (for P model)
Interface RS-232 / USB (for P model)
Light
Transmission(%)
NP-5xxxA SERIES User Manual
350 350 330 330
140/110 140/125 160/140 170/170
80% / 90% (for P model)
7
Power
Power Input 9~36V DC
Mechanical
Construction Sliver aluminum front bezel and chassis
IP Rating IP65 front panel
Mounting Panel mounting, VESA 75 x 75 Panel mounting, VESA 100 x 100
Dimension (mm) 202 x 149 x 39 231 x 176 x 51 319 x 245 x 51.68 410 x 310 x 54.67
Net Weight (Kgs) 2.3 3.2 4.0 6.3
Environmental
Operating
0~50℃
Temperature
Storage
-20~60℃
Temperature
Relative
10 to 90% @ 40°C, non- condensing
Humidity
Vibration
5~500Hz 0.002G2/Hz (X,Y,Z direction) 1Grms 30 minutes
(operation)
Shock
Half Sine Pulse @15G PW 11ms (X,Y,Z direction) 18 Shocks
(operation)
Certificate CE / FCC Class A
Certification CE / FCC Class A
Operating
System Support
Note 1: NP-5XXA series is covered by one or more of the following patents: US6, 570, 884, US6,115,776, and US6,327,625.
Windows XP pro, Windows XP Embedded, Windows Embedded CE6.0(Note 1), Windows 7 pro for
Embedded Windows Embedded standard 7(Win 7 support 3D Graphic function)
1.2 Dimensions
NP-5xxxA SERIES User Manual
8
Figure 1.1: Dimensions of NP-507A
NP-5xxxA SERIES User Manual
9
Figure 1.2: Dimensions of NP-508A
Figure 1.3: Dimensions of NP-512A
Figure 1.4: Dimensions of NP-515A
NP-5xxxA SERIES User Manual
10
1.3 Brief Description of NP-5xxA SERIES
There are 7”, 8”, 12”, 15” Industrial Compact Size Panel PC in NP-5XXA series, which comes with
flat front panel touch screen and fanless design. It is powered by an Intel Atom N2600 1.6GHz CPU
built-in, 2GB DDR III 800 MHz. NP-5xxA series is 9~36VDC wide-ranging power input and IP65
compliant front panel. Optional projected capacitive touchscreen support 7H anti-scratch surface is
ideal for use as a PC-based controller for Industrial Automation & Factory Automation.
NP-5xxxA SERIES User Manual
11
Figure 1.5: Front View of NP-5XXA SERIES
Figure 1.6: Rear View of NP-507A/NP-508A
NP-5xxxA SERIES User Manual
12
Figure 1.7: Rear View of NP-512A/ NP-515A
1.4 Installation of HDD(NP-507A/NP-508A)
Step 1
There are 2 screws to deal with when
enclosing or removing the chassis. Gently
remove 2 screws.
Step 2
There is a SSD card in the bracket. Gently
remove the screw, then carefully pull SSD
card.
NP-5xxxA SERIES User Manual
13
Step 3
Take out SSD Card bracket.
Step 4.
You can replace SSD card by unscrewing 4
screws as shown in the picture.
Note: 4 screws are packed in the packing
list.
Step 5
There is a SD card hole in the side of the
machine. You can replace SD card from
there.
NP-5xxxA SERIES User Manual
14
Step 6.
Gently screw the screws.
Installation of HDD(NP-512A / NP-515A)
Step 1
There are 2 screws to deal with when
enclosing or removing the chassis. Gently
remove 2 screws.
NP-5xxxA SERIES User Manual
15
Step 2
You can put or remove HDD into the
machine by pulling the HDD bracket.
Step 3
You can remove HDD by unscrewing 4
screws in the HDD bracket.
Note: 4 screws are packed in the packing
package.
Step 4
There is a SD hole in the side of machine.
You can replace SD card from there.
NP-5xxxA SERIES User Manual
16
Chapter 2 Hardware
2.1 Mainboard
Specifications
Board Size 170mm x 113mm
CPU Support
Chipset
Memory
Support
Graphics
Display Mode
Support
Resolution
Dual Display
Super I/O
BIOS
Storage
Intel Atom N2600 /1.60GHz
Intel NM10 Express
Onboard 2GB DDRIII SDRAM
Integrated Intel GMA 3600 (N2600)
1 x CRT Port
1 x LVDS1 (18/24-bit single LVDS)
Up to 1920 x1200 for CRT
Up to 1366 x768 for LVDS1 (N2600)
CRT+LVDS1
Winbond W83627UHG-E
AMIBIOS
1 x SATA Connector (7P)
1 x SATA Connector (7P+15P)
1 x SD Socket (USB to SD)
Ethernet 2 x PCIe GbE LAN by Realtek RTL8111E
USB
Serial
Digital I/O
NP-5xxxA SERIES User Manual
2 x USB 2.0 (type A)stack ports (USB4/USB5)
2 x USB 2.0 Pin header via CN3 (USB2/USB3)
2 x USB 2.0 Pin header via CN1 (USB0/USB1)
1 x USB 2.0 for MPCIE1 (USB7)
Mini-PCIe(USB7)
1 x RS-232/RS-422/RS-485, DB9 connector for external
(COM1)
pin 9 w/5V/12V/Ring select
1 x RS232 port, DB9 connector for external (COM2)
pin 9 w/5V/12V/Ring select
1 x RS422/485 header via CN2 (COM3)
2 x UART via CN3 (COM5,COM6)
8-bit digital I/O Pin header via CN2
17
4-bit digital Input
4-bit digital Output
4-bit digital I/O Pin header via CN3
2-bit digital Input
2-bit digital Output
Battery
Audio
Keyboard
/Mouse
Expansion Bus
Touch Ctrl
Power
Management
Switches and
LED Indicators
Support CR2477 Li battery by 2-pin header
Realtek ALC662 HD audio codec
Line-in, Line-out, MIC via 2x6-pin header
Audio Line out in phone jack
1 x PS2 keyboard/mouse 1x6 box pin header via CN3
1 x mini-PCI-express slot
1 x PCI-express via CN3
1 x Touch control header for TCH1 (COM4)
Wide Range DC 9~36V input
1 x 3-pin power input connector
1 x Power on/off switch via CN1
1 x Reset switch via CN1
1 x Power LED status via CN1
1 x HDD LED status via CN1
1 x Buzzer
External I/O
port
2 x COM Ports (COM1/COM2)
2 x USB 2.0 Ports (USB4/USB5)
2 x GbE LAN Ports
1 x Line out Audio phone jack
Watchdog
Timer
Software programmable 1 – 255 second by Super I/O
Operating: -20℃ to 70℃
Temperature
Humidity
Power
Consumption
EMI/EMS
Storage: -40℃ to 85℃
5% - 95%, non-condensing, operating
12V /0.95A (Intel Atom N2600 processor with 2GB DDR3
DRAM)
Meet CE/FCC class A
NP-5xxxA SERIES User Manual
18
(units :mm)
Figure 2.1: Mainboard Dimensions
NP-5xxxA SERIES User Manual
19
2.2 Installations
SBC-7106 is a 4" industrial motherboard developed on the basis of Intel Cedarview-M Processors and
NM10, which provides abundant peripheral interfaces to meet the needs of different customers. Also,
it features dual GbE ports, 3-COM ports and one Mini PCIE configuration, one VGA port, one HDMI
port, one LVDS interface. To satisfy the special needs of high-end customers, CN1 and CN2 and CN3
richer extension functions. The product is widely used in various sectors of industrial control.
2.2.1 Jumpers Setting and Connectors
Board Top
Figure 2.2: Jumpers and Connectors Location_ Board Top
Board Bottom
NP-5xxxA SERIES User Manual
20
Figure 2.3: Jumpers and Connectors Location_ Board Bottom
2.3 Jumpers Setting and Connectors
1. JP5:
(2.0mm Pitch 1X2 box Pin Header),ATX Power and Auto Power on jumper setting.
JP5 Mode
Open ATX Power
NP-5xxxA SERIES User Manual
Close
Auto Power on
(Default)
21
3. BAT1 :
(1.25mm Pitch 1X2 box Pin Header) 3.0V Li battery is embedded to provide power for
CMOS.
Pin#
Signal
Name
Pin1 VBAT
PIN2 Ground
4. DC_IN1:
(5.08mm Pitch 1x3 Pin Connector),DC9V~36V System power input connector。
Pin# Power Input
Pin1 DC+9V~32V
Pin2 Ground
Pin3 FG
6. VGA1:
(CRT 2.0mm Pitch 2X6 Pin Header), Video Graphic Array Port, Provide 2x6Pin cable to
VGA Port.
Signal Name Pin# Pin# Signal Name
CRT_RED 1 2 Ground
CRT_GREEN 3 4 Ground
CRT_BLUE 5 6 Ground
CRT_H_SYN
C
CRT_V_SYNC
Ground 11 12 Ground
7 8 CRT_DDCDAT
A
9 10 CRT_DDCCL
K
NP-5xxxA SERIES User Manual
22
8. JP1:
, Pin2, Pin3, Pin4
(2.0mm Pitch 2x3 Pin Header),COM1 jumper setting, pin 1~6 are used to select signal
out of pin 9 of COM1 port.
JP1 Pin# Function
Close 1-2 COM1 RI (Ring Indicator)
(default)
Close 3-4 COM1 Pin9=+5V
(option)
Close 5-6 COM1 Pin9=+12V
(option)
9. RS-232:
(Switch),COM1 jumper setting, it provides selectable RS232 or RS422 or RS485 serial
signal output.
Function S_232 Pin#
RS232
(Default)
RS422
(option)
RS485
(option)
10. RS-422:
(Switch),COM1 setting, it provides selectable RS232 or RS422/RS485 serial signal
output.
Function RS_422 Pin#
RS232
(Default)
ON:
Pin1, Pin2, Pin3, Pin4
OFF:
Pin1, Pin2, Pin3, Pin4
OFF:
Pin1, Pin2, Pin3, Pin4
OFF: Pin1
(option)
(option)
Note: Must keep the setting with BIOS setting.
NP-5xxxA SERIES User Manual
RS422
RS485
ON: Pin1, Pin2, Pin3, Pin4
ON: Pin1, Pin2, Pin3, Pin4
23
11. COM1:
(Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a direct
connection to serial devices. COM1 port is controlled by pins No.1~6 of JP1,select
output Signal RI or 5V or 12V, For details, please refer to description of JP1 and S_232
and S_422 setting.
RS232 (Default):
Pin# Signal Name
1 DCD# (Data Carrier Detect)
2 RXD (Received Data)
3 TXD (Transmit Data)
4 DTR (Data Terminal Ready)
5 Ground
6 DSR (Data Set Ready)
7 RTS (Request To Send)
8 CTS (Clear To Send)
9
JP1 select Setting (RI/5V/12V)
BIOS Setup：
Advanced/W83627UHG Super IO
Configuration/Serial Port 1 Configuration【RS-232】
RS422/RS485 (option):
Pin# Signal Name
1 422_RX+
2 422_RX3 422_TX4 422_TX+
5 Ground
6 NC
BIOS Setup：
Advanced/W83627UHG Super IO
Configuration/Serial Port 1 Configuration【RS-422】
NP-5xxxA SERIES User Manual
7 NC
8 NC
9 NC
24
RS485 2Wire (option):
Pin# Signal Name
1 NC
2 NC
3 4854 485+
5 Ground
6 NC
7 NC
8 NC
9 NC
BIOS Setup：
Advanced/W83627UHG Super IO
Configuration/Serial Port 1 Configuration【RS-485】
12 JP2:
(2.0mm Pitch 2x3 Pin Header), COM2 jumper setting, pin 1~6 are used to select signal
out of pin 9 of COM2 port.
JP2 Pin# Function
Close 1-2 COM1 RI (Ring Indicator)
(default)
Close 3-4 COM1 Pin9=+5V
(option)
Close 5-6 COM1 Pin9=+12V
(option)
NP-5xxxA SERIES User Manual
25
13. COM2:
(Type DB9),Rear serial port, standard DB9 Male serial port is provided to make a
direct connection to serial devices.
Pin# Signal Name
1 DCD# (Data Carrier Detect)
2 RXD (Received Data)
3 TXD (Transmit Data)
4 DTR (Data Terminal Ready)
5 Ground
6 DSR (Data Set Ready)
7 RTS (Request To Send)
8 CTS (Clear To Send)
9
RI (Ring Indicator)
16. LED3:
LED STATUS. Green LED for Touch Power status.
19 SATA1:
(SATA 7Pin+15Pin), SATA Connectors, one SATA connectors are provided, with transfer
speed up to 3.0Gb/s.
20 SD1:
(SD card socket),Secure Digital Memory Card socket.
NP-5xxxA SERIES User Manual
26
23. LINE_OUT:
(Diameter 3.5mm Jack), HD Audio port, An onboard Realtek ALC662 codec is used to
provide high quality audio I/O ports. Line Out can be connected to a headphone or
amplifier.
24. USB45:
USB4/USB5：：：：(Double stack USB type A), Rear USB connector, it provides up to 4
USB2.0 ports, High-speed USB 2.0 allows data transfers up to480 Mb/s ,support USB
full-speed and low-speed signaling.
Each USB Type A Receptacle (2 Ports) Current limited value is 1.5A.
If the external USB device current exceeds 1.5A, please separate connectors
into different Receptacle.
25. LAN1/LAN2:
LAN1/LAN2: (RJ45 Connector), Rear LAN port, Two standard 10/100/1000M RJ-45
Ethernet ports are provided. Used Realtek RTL8111E chipset, LINK LED (green) and
ACTIVE LED (yellow) respectively located at the left-hand and right-hand side of the
Ethernet port indicate the activity and transmission state of LAN.
26. BUZ1:
Onboard buzzer.
27 LED1:
LED STATUS. Green LED for Motherboard Power status.
NP-5xxxA SERIES User Manual
27
28. LED2:
LED STATUS. Green LED for Motherboard Standby Power Good status.
31. CN3:
(1.27mm Pitch 2X30 Pin Header), For expand output connector, It provides four GPIO,
Two USB 2.0,one PS/2 mouse，one PS/2 keyboard,two uart,one PCIe x1,one SMbus.
Function Signal Name Pin# Pin# Signal Name Function
5V_S5_USB 1 2 5V_S5_USB
5V_S5_USB 3 4 5V_S5_USB
USB23_OC 5 6
USB2 USB2_N 7 8 USB2_P USB2
USB3 USB3_N 9 10 USB3_P USB3
Ground 11 12 Ground
PS/2 MS PS2_MSCLK 13 14 PS2_MSDATA PS/2 MS
PS/2 KB PS2_KBCLK 15 16 PS2_KBDATA PS/2 KB
CLKREQPSON_ATX-
COM6
(UART)
COM6_RI 17 18 COM6_DCD-
COM6_TXD 19 20 COM6_RXD
COM6_DTR 21 22 RICOM6_RTS
COM6
(UART)
-
COM6_DSR 23 24 COM6_CTS-
Ground 25 26 Ground
COM5
(UART)
COM5_RI 27 28 COM5_DCD-
COM5_TXD 29 30 COM5_RXD
COM5_DTR 31 32
COM5_DSR 33 34
DSRCOM5_RTSDTRCOM5_CTS-
COM5
(UART)
GPIO24 ICH_GPIO24 35 36 ICH_GPIO13 GPIO13
GPIO26 ICH_GPIO26 37 38 ICH_GPIO27 GPIO27
Ground 39 40 Ground
PCIE
PE1_TX_N0 41 42 PE1_TX_P0
PE1_RX_N0 43 44 PE1_RX_P0
Ground 45 46 Ground
CLK_100M_PE1_N
PM_PCIE_WAKE
47 48
49 50 PLTRST_BUF-
CLK_100M_PE1_P
PCIE
SMBUS SMB_CLK_S5 51 52 SMB_DATA_S5 SMBUS
PE1_CLKREQ 53 54 Ground
PCIE
NP-5xxxA SERIES User Manual
PCIE
3P3V_S5 55 56 3P3V_S5
28
3P3V_S5 57 58 3P3V_S5
12V 12V_S0 59 60 12V_S0 12V
NP-5xxxA SERIES User Manual
29
3 BIOS Setup Description
3.1 Operations after POST Screen
After CMOS discharge or BIOS flashing operation, Press [Delete] key to enter CMOS Setup.
Version 2.15.1226. Copyright (C) 2012 American Megatrends, Inc.
BIOS Date: 12/17/2012 02:22:46 Ver: 7106V002
Press 〈〈〈〈DEL〉〉〉〉or〈〈〈〈F2〉〉〉〉to enter setup
A3
After optimizing and exiting CMOS Setup, the POST screen displayed for the first time is as follows and
includes basic information on BIOS, CPU, memory, and storage devices.
NP-5xxxA SERIES User Manual
30
3.2 BIOS SETUP UTILITY
Press [Delete] key to enter BIOS Setup utility during POST, and then a main menu containing
system summary information will appear.
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
BIOS Information
BIOS Vendor American Megatrends
Core Version 4.6.5.3
Compliancy UEFI 2.3; PI 1.2
Project Version 7106V002
Build Date and Time 12、17、2012 03:22:46
►Intel RC Version
System Language [English]
System Date [Sun 01/01/2012]
System Time [00:00:08]
Access Level Administrator
Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc.
Intel Reference Code
Version
→←: Select Screen
↑↓ : Select Item
Enter: Select
+/- : Charge Opt.
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC Exit
3.3 Main Settings
BIOS Information
BIOS Vendor American Megatrends
Core Version 4.6.5.3
Compliancy UEFI 2.3; PI 1.2
Project Version 7106V002
Build Date and Time 12、17、2012 03:22:46
►Intel RC Version
NP-5xxxA SERIES User Manual
Intel Reference Code
Version
31
System Language [English]
System Date [Sun 01/01/2012]
System Time [00:00:08]
Access Level Administrator
Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc.
→←: Select Screen
↑↓ : Select Item
Enter: Select
+/- : Charge Opt.
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC Exit
System Time:
Set the system time, the time format is:
Hour : 0 to 23
Minute : 0 to 59
Second : 0 to 59
System Date:
Set the system date, the date format is:
Day: Note that the ‘Day’ automatically changes when you set the date.
Month: 01 to 12
Date: 01 to 31
Year: 1998 to 2099
NP-5xxxA SERIES User Manual
32
3.4 Advanced Settings
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
►PCI Subsystem Settings
►ACPI Settings
►CPU Configuration
►Thermal Configuration
►IDE Configuration
►USB Configuration
►W83627UHG Super IO Configuration
►W83627UHG HW Monitor
►Serial Port Console Redirection
►PPM Configuration
Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc.
PCI,PCI-X and PCI
Express Settings
→←: Select Screen
↑↓ : Select Item
Enter: Select
+/- : Charge Opt.
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC Exit
3.4.1 PCI Subsystem Settings
PCI Bus Driver Versio V2.05.02
PCI Common Settings:
PCI Latency Timer:
[32 PCI Bus Clocks]
[64 PCI Bus Clocks]
[96 PCI Bus Clocks]
[128 PCI Bus Clocks]
[160 PCI Bus Clocks]
[192 PCI Bus Clocks]
[224 PCI Bus Clocks]
[248 PCI Bus Clocks]
VGA Palette Snoop:
[Disabled]
[Enabled]
PERR# Generation:
NP-5xxxA SERIES User Manual
33
[Disabled]
[Enabled]
SERR# Generation:
[Disabled]
[Enabled]
3.4.2 ACPI Settings
Enable ACPI Auto Conf:
[Disabled]
[Enabled]
Enable Hibernation:
[Enabled]
[Disabled]
ACPI Sleep State:
[Both S1 and S3 available for OS to choose from ]
[Suspend Disabled]
[S1 only(CPU Stop Clock) ]
[S3 only (Suspend to RAM) ]
Lock Legacy Resources:
[Disabled]
[Enabled]
S3 Video Repost:
[Disabled]
[Enabled]
3.4.3 CPU Configuration
Processor Type Intel(R) Atom(TM) CPU N2600
EMT64 Not Supported
Processor Speed 1600 MHz
System Bus Speed 400MHz
Ratio Status 16
Actual Ratio 16
System Bus Speed 400 MHz
Processor Stepping 30661
Microcode Revision 269
NP-5xxxA SERIES User Manual
34
L1 Cache RAM 2x56 k
L2 Cache RAM 2x512 k
Processor Core Dual
Hyper-Threading Supported
Hyper-Threading:
[Enabled]
[Disabled]
Execute Disable Bit:
[Enabled]
[Disabled]
Limit CPUID Maximum:
[Disabled]
[Enabled]
3.4.4 Thermal Configuration
CPU Thermal Configuration
DTS SMM
[Disabled]
[Enabled]
Platform Thermal Configuration
Critical Trip Point [POR]
Active Trip Point Lo [55 C]
Active Trip Point Hi [71C]
Passive Trip Point [95]
Passive TC1 Value 1
Passive TC2 Value 5
Passive TSP Value 10
3.4.5 IDE Configuration
SATA Port0 Not Present
SATA Port1 Not Present
SATA Controller(S):
[Disabled]
Configure SATA as:
[IDE]
NP-5xxxA SERIES User Manual
[Enabled]
35
[AHCI]
Misc Configuration for hard disk
3.4.6 USB Configuration
USB Configuration
USB Devices:
1 Drive ，1 keyboard
Legacy USB Support:
[Enabled]
[Disabled]
EHCI Hand-off:
[Disabled]
[Enabled]
USB hardware delays a
USB transfer time-out:
[20 sec]
[10 sec]
[5 sec]
[1 sec]
Device reset time-out:
[20 sec]
[10 sec]
[30 sec]
[40 sec]
Device power-up delay
[Auto]
[Manual]
Mass Storage Devices：
Multiplecard Reader 1
[Auto]
[Floppy]
[Forced FDD]
[Hard Disk]
[CD-ROM]
3.4.7 W83627UHG Super IO Configuration
W83627UHG Super IO ch W83627UHG
Serial Port 1 Configuration
UART Mode Selection：
[RS-232]
NP-5xxxA SERIES User Manual
36
[RS-485]
[RS-422]
Serial Port 2 Configuration
Serial Port 3 Configuration
UART Mode Selection：
[RS-485]
[RS-422]
Serial Port 4 Configuration
Serial Port 5 Configuration
Serial Port 6 Configuration
Power Failure
[Keep last state]
[Always off]
[Always on]
3.4.8 W83627UHG HW Monitor
PC Health Status
System temperature1 : +38
System Speed : N/A
VCORE : +0.968 V
+12V : +12.302 V
+3.3V : +3.320 V
+1.5V : +1.528 V
AVCC : +5.203 V
VCC5V : +5.216 V
VSB5 : +5.203 V
VBAT : +3.334 V
3.4.9 Serial Port Console Redirection
COM0
Console Redirection
[Enabled]
[Disabled]
Console Redirection Settings
Serial Port for Out-of-Band Management/
Windows Emergency Management Services (EMS)
Console Redirection
NP-5xxxA SERIES User Manual
37
[Disabled]
[Enabled]
Console Redirection Settings
3.4.10 PPM Configuration
PPM Configuration
EIST:
[Enabled]
[Disabled]
CPU C state Report
[Enabled]
[Disabled]
Enhanced C state
[Enabled]
[Disabled]
CPU Hard C4E
[Enabled]
[Disabled]
CPU C6 state
[Enabled]
[Disabled]
C4 Exit Timing
[Fast]
[Default]
[Slow]
C-state POPDOWN
[Enabled]
[Disabled]
C-state POPUP
[Enabled]
[Disabled]
NP-5xxxA SERIES User Manual
38
3.5 Chipset Settings
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
►Host Bridge
►South Bridge
Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc.
Host Bridge Parameters
→←: Select Screen
↑↓ : Select Item
Enter: Select
+/- : Charge Opt.
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC Exit
3.5.1 Host Bridge
►Memory Frequency and Timing
►Intel IGD Configuration
******* Memory Information *******
Memory Frequency 800 MHz(DDR3)
Tot al Memory 2048 MB
DIMM#0 Not Present
DIMM#1 2048 MB
Memory Frequency and Timing
MRC Fast Boot
[Enabled]
[Disabled]
Max TOLUD
[Dynamic]
[1GB]
[1.25GB]
NP-5xxxA SERIES User Manual
39
[1.5GB]
[1.75GB]
[2GB]
[2.25GB]
[2.5GB]
[2.75GB]
[3GB]
[3.25GB]
Intel IGD Configuration
IGFX – Boot Type
[VBIOS Default]
[VGA]
[LVDS]
[VGA + LVDS]
LCD Panel Type
[VBIOS Default]
[640x480，18bit]
Panel Scaling
[800x480，18bit]
[800x600，18bit]
[1024x600，18bit ]
[1024x768，18bit ]
[1280x768，18bit ]
[1280x800，18bit ]
[1280x1024，18bit]
[1366x768，18bit]
[1024x768，24bit]
[1280x768，24bit]
[1280x800，24bit]
[1280x1024，24bit]
[Auto]
[Force Scaling]
[off]
[Maintain Aspect Ratio]
Active LFP
NP-5xxxA SERIES User Manual
[LVDS]
[No LVDS]
[EDP]
40
IGD Clock Source
[External Clock]
[Internal Clock]
Fixed Graphics Memory
[128MB]
[256MB]
ALS Support
[Disabled]
[Enabled]
Back light Control
[DC]
[PWM]
Back light Logic
Back light Control Lev
[Positive]
[Negative]
[Auto]
[Disabled]
[Level 8]
[Level 1]
[Level 2]
[Level 3]
[Level 4]
[Level 5]
[Level 6]
[Level 7]
[Level 8]
[Level 9]
[Level 10]
[Level 11]
NP-5xxxA SERIES User Manual
[Level 12]
[Level 13]
[Level 14]
[Level 15]
41
3.5.2 South Bridge
TPT Devices
PCI Express Root Port 0
PCI Express Root Port 1
PCI Express Root Port 2
PCI Express Root Port 3
DMI Link ASPM Control
[Enabled]
[Disabled]
PCI-Exp. High Priorit
[Disabled]
[Enabled]
High Precision Event Timer Configuration
High Precision Timer
[Enabled]
[Disabled]
SLP_S4 Assertion Widt
[1-2 Seconds]
[2-3 Seconds]
[3-4 Seconds]
[4-5 Seconds]
Restore AC Power Loss
[Last State]
[Power off]
[Power on]
NP-5xxxA SERIES User Manual
42
3.6 Boot Settings
Main Advanced Chipset Boot Security Save & Exit
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Boot Configuration
Setup Prompt Timeout 1
Bootup Numlock State [On]
Quiet Boot [Disabled]
Fast Boot [Enabled]
Skip USB [Disabled]
Skip PS2 [Disabled]
CSM16 Module Version 07.69
Gatea20 Active [Upon Request]
Option ROM Messages [Force BIOS]
Interrupt 19 Capture [Enabled]
Driver Option Priorities
Boot Option Priorities
Boot Option Priorities
Boot Option #1 [SATA PM: Hitachi…]
Boot Option #2 […]
Hard Drive BBS Priorities
►CSM Parameters
Number of seconds to
Wait for setup
Activation key.
65535(0xFFFF)means
Indef inite waiting.
→←: Select Screen
↑↓ : Select Item
Enter: Select
+/- : Charge Opt.
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC Exit
Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc.
Setup Prompt Timeout [1]
Bootup Numlock State
Quiet Boot
NP-5xxxA SERIES User Manual
[On]
[off]
[Disabled]
43
[Enabled]
Fast Boot
[Enabled]
[Disabled]
Skip VGA
[Enabled]
[Disabled]
Skip USB
[Disabled]
[Enabled]
Skip PS2
[Disabled]
[Enabled]
CSM16 Module Version 07.69
Gatea20 Active
[Upon Request]
[Always]
Option ROM Messages
[Force BIOS]
[Keep Current]
Interrupt 19 Capture
[Immediate]
[Postponed]
Boot Option #1
Boot Option #2
……
Sets the system boot order
Hard Drive BBS Priorities [SATA PM:*** … ]
Boot Option #1
SATA PM:***…
******
Disabled
CSM Parameters
Launch CSM
NP-5xxxA SERIES User Manual
[Always]
44
[Never]
Boot option filter
[UEFI and Legacy]
[Legacy only]
[UEFI only]
Launch PXE OpROM poli
[Do not Launch]
[UEFI only]
[Legacy only]
Launch Storage OpROM
[Legacy only]
[Do not Launch]
[UEFI only]
Launch Video OpROM po
[Do not Launch]
[UEFI only]
[Legacy only]
Other PCI device ROM
[UEFI OpROM]
[Legacy OpROM]
NP-5xxxA SERIES User Manual
45
3.7 Security Settings
Aptio Setup Utility – Copyright (C) 2012
American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
Password Description
If ONLY the Administrator’s password is set,
Then this only limits access to Setup and is
Only asked for when entering Setup.
If ONLY the User’s password is set, then this
Is a power on password and must be entered to
Is a power on password and must be entered to
Boot or enter Setup. In Setup the User will
Have Administrator rights.
The password length must be
In the following range:
Minimum length 3
Maximum length 20
Administrator Password
User Password
Set Administrator
Password
→←: Select Screen
↑↓ : Select Item
Enter: Select
+/- : Charge Opt.
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC Exit
Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc.
6.4.1 Administrator Password
6.4.2 User Password
Type the password with up to 20 characters and then press Enter key. This will clear all
previously typed CMOS passwords. You will be requested to confirm the password. Type the
password again and press Enter key. You may press Esc key to abandon password entry
operation.
To clear the password, just press Enter key when password input window pops up. A
confirmation message will be shown on the screen as to whether the password will be disabled.
NP-5xxxA SERIES User Manual
46
You will have direct access to BIOS setup without typing any password after system reboot once
w
the password is disabled.
Once the password feature is used, you will be requested to type the password each time you
enter BIOS setup. This will prevent unauthorized persons from changing your system
configurations.
Also, the feature is capable of requesting users to enter the password prior to system boot to
control unauthorized access to your computer. Users may enable the feature in Security Option
of Advanced BIOS Features. If Security Option is set to System, you will be requested to enter
the password before system boot and when entering BIOS setup; if Security Option is set to
Setup, you will be requested for password for entering BIOS setup.
3.8 Save and Exist Settings
BIOS SETUP UTILITY
Main Advanced PCIPnP Boot Security Chipset Exit
Advanced Chipset Settings
WARNING: Setting wrong values in belo
sections
may cause system to malfunction
► North Bridge Configuration
► South Bridge Configuration
Configure North Bridge
feature
← Select Screen
↑↓ Select Item
Enter Go to sub screen
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 © Copyright 1985-2006 American Mega trends , Inc.
Note: Due to limited address length of BIOS, only a portion of panel parameters are listed in
BIOS Setup. If the connected panel is not included in the parameter list, display
problem will occur. In this case, Please do not change BIOS setup.
NP-5xxxA SERIES User Manual
47
3.8.1 North Bridge Configuration
Memory Remap Feature
Memory Hole
IGD Graphics Mode Select
IGD GTI Graphic smemory size [No VT
BIOS SETUP UTILITY
Chipset
North Bridge Chipset Configuration
[Enabled]
PCI MMIO Allocation: 4Gb To 3072MB
[Disabled]
Initate Graphic Adapter [PCI/IGD]
[Enabled ,64MB]
mode,2MB]
PEG Port Configuration
► Video Function Configuration
ENABLE: Allow
Remapping of
Over lapped PCI Memory
Above the total
Physical memory
DISABLE: Do not allow
remapping of memory
← Select Screen
↑↓ Select Item
+- Charge Field
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 © Copyright 1985-2006 American Mega trends , Inc.
Memory Remap Feature:
[Enabled]
[Disabled]
Memory Hole:
[Disabled]
[15MB-16MB]
Initate Graphic Adapter:
Select which graphics controller to use as the primary boot device.
[IGD]
[PCI/IGD]
IGD Graphics Mode Select:
[Enabled, 64MB]
[Disabled]
NP-5xxxA SERIES User Manual
48
[Enabled, 32MB]
DVMT
DVMT/FIXED Memory
Boot Display Device
[1024x768
Backlight Image Adaptation
[Enabled, 128MB]
Video Function Configuration:
BIOS SETUP UTILITY
Chipset
Video Function Configuration
DVMT Mode Select [
Mode]
[256MB]
[VBIOS-Default]
Flat Panel Type
18bit 1c]
Backlight Control Support
[VBIOS-Default]
Backlight Control Level [Level 5]
Backlight Control Mode [DC]
[VBIOS-Default]
Options
Fixed Mode
DVMT Mode
← Select Screen
↑↓ Select Item
+- Charge option
F1 General Help
F10 Save and Exit
ESC Exit
DVMT Mode Select:
DVMT/FIXED Memory Size:
Boot Display Device:
[BIOS-Default]
NP-5xxxA SERIES User Manual
V02.61 © Copyright 1985-2006 American Mega trends , Inc.
[DVMT Mode]
[FIXED Mode]
[256MB]
[128MB]
[Maximum DVMT]
[CRT]
49
[LVDS]
[CRT + LVDS]
Flat Panel Type:
[1024x 768 18bit 1ch]
[640x480 18bit 1ch]
[800x600 18bit 1ch]
[1280x800 18bit 1ch]
[1366x768 18bit 1ch]
[1024x 768 24bit 2ch]
[1440x900 24bit 2ch]
[1600x900 24bit 2ch]
[1680x1050 24bit 2ch]
[1920x1080 24bit 2ch]
Backlight Control Support
[VBIOS-Default]
[Both BLC & BIA Disabled]
[BLC Enabled]
Backlight Control Control:
[Level5]
[Level0]
[Level1]
[Level2]
[Level3]
[Level4]
[Level6]
[Level7]
Note: Panel support PWM Function.
Backlight Control Mode:
[DC]
[PWM]
Backlight Image Adaptation:
[VBIOS-Default]
NP-5xxxA SERIES User Manual
[BIA Disabled]
[BIA Enabled at Level1]
[BIA Enabled at Level2]
50
[BIA Enabled at Level3]
[BIA Enabled at Level4]
[BIA Enabled at Level5]
3.8.2 South Bridge Configuration:
Aptio Setup Utility – Copyright (C) 2012 American Megatrends, Inc.
Main Advanced Chipset Boot Security Save & Exit
Save Changes and Exit
Discard Changes and Exit
Save Changes and Reset
Discard Changes and Reset
Save Options
Save Changes
Discard Changes
Restore Defaults
Save user Defaults
Restore user Defaults
Boot Override
MultipleCard Reader 1.00
SATA PM:*** …
Launch EFI Shell from filesystem device
Exit system setup after
Saving the changes.
→←: Select Screen
↑↓ : Select Item
Enter: Select
+/- : Charge Opt.
F1 : General Help
F2: Previous Values
F3:Optimized Defaults
F4:Save and Exit
ESC Exit
Version 2.15.1226. Copyright (C) 2012 American Megatrends , Inc.
Save Changes and Exit
Save & Exit Setup save Configuration and exit ?
[Yes]
Discard Changes and Ext
Exit Without Saving Quit without saving?
[Yes]
Save Changes and Reset
Save & reset Save Configuration and reset?
[Yes]
NP-5xxxA SERIES User Manual
[No]
[No]
51
[No]
Discard Changes and Reset
Reset Without Saving Reset without saving?
[Yes]
[No]
Save Changes
Save Setup Values Save configuration?
[Yes]
[No]
Discard Changes
Load Previous Values Load Previous Values?
[Yes]
[No]
Restore Defaults
Load Optimized Defaults Load optimized Defaults?
[Yes]
[No]
Save user Defaults
Save Values as User Defaults Save configuration?
[Yes]
[No]
Restore user Defaults
Restore User Defaults Restore User Defaults?
[Yes]
[No]
Launch EFI Shell from filesystem device
WARNING Not Found
[ok]
NP-5xxxA SERIES User Manual
52
3.9 Exit Options
Main Advanced PCIPnP Boot Security Chipset Exit
BIOS SETUP UTILITY
Exit Options
Save Changes and Exit
Discard Changes and Exit
Discard Changes
Load Optimal Defaults
Load Failsafe Defaults
Exit system setup
after saving the
changes
F10 key can be used
For this operation
← Select Screen
↑↓ Select Item
Enter Go to sub screen
F1 General Help
F10 Save and Exit
ESC Exit
V02.61 © Copyright 1985-2006 American Mega trends , Inc.
Save Changes and Exit:
Save configuration changes and exit setup?
(F10 key can be used for this operation)
[OK]
[Cancel]
Discard Changes and Exit:
Discard Changes and Exit setup?
(ESC key can be used for this operation)
[OK]
[Cancel]
Discard Changes:
Discard changes?
(F7 key can be used for this operation)
[OK]
[Cancel]
NP-5xxxA SERIES User Manual
53
Load Optimized Defaults:
Load Optimized Defaults?
(F9 key can be used for this operation)
[Cancel]
Load Fail-Safe Defaults:
Load Fail-Safe Defaults?
(F9 key can be used for this operation)
[Cancel]
[OK]
[OK]
NP-5xxxA SERIES User Manual
54
Chapter 4 Installation of Drivers
This chapter describes the installation procedures for software and drivers under the windows XP.
The software and drivers are included with the motherboard. The contents include Intel chipset driver,
VGA driver, LAN drivers, Audio driver Installation instructions are given below.
Important Note:
After installing your Windows operating system (Windows XP), you must install
first the Intel Chipset Software Installation Utility before proceeding with the
installation of drivers.
I
NP-5xxxA SERIES User Manual
55
4.1 Intel Chipset Driver
NP
-
5xxA
To install the Intel chipset driver, please follow the steps below.
Step 1. Select Intel (R) Chipset NM10 Express from the list
Step 2. Click Next to setup program.
NP-5xxxA SERIES User Manual
56
Step 3. Read the license agreement. Click Yes to accept all of the terms of the license agreement.
Step 4. Click Next to continue.
NP-5xxxA SERIES User Manual
57
Step 5. Click Next.
Step 6. Select Yes, I want to restart this computer now. Click Finish, then remove any installation
media from the drives.
NP-5xxxA SERIES User Manual
58
4.2 Intel Graphics Media Accelerator driver
NP
-
5xxA
To install the VGA drivers, follow the steps below to proceed with the installation.
Step 1.Select Intel(R) VGA Chipset Driver.
Step 2. Select Installs driver and application files. Click Next.
NP-5xxxA SERIES User Manual
59
Step 3. Select I agree. Click Install.
Step 4. Click Continue Anyway.
NP-5xxxA SERIES User Manual
60
Step 5. Click Continue Anyway.
Step 6. To restart the computer, click Yes.
NP-5xxxA SERIES User Manual
61
4.3 Intel (R) Network Adapter
NP
-
5xxA
To install the Intel (R) Network Adapter device driver, please follow the steps below.
Step 1. Select Realtek RTL8111D Driver.
Step 2. Click Next to continue.
NP-5xxxA SERIES User Manual
62
Step 3. Click Install to begin the installation.
Step 4. Click Finish to exist the wizard.
NP-5xxxA SERIES User Manual
63
NP
-
5xxA
4.4 Realtek ALC662 HD Audio Codec Driver Installation
To install the Realtek ALC662 HD Audio Codec Driver, please follow the steps below.
Step 1. Select Realtek AL662 Audio Codec Driver from the list
Step 2. Click Next to continue.
NP-5xxxA SERIES User Manual
64
Step 3. Click Yes, I want to restart my computer now. Click Finish to complete the installation.
NP-5xxxA SERIES User Manual
65
NP
-
5xxA
Chapter 5 Touch Screen Installation
This chapter describes how to install drivers and other software that will allow your touch screen work
with different operating systems.
5.1 Windows 2000/XP/2003/Vista/WIN7 Universal Driver
Installation for PenMount 6000 Series
Before installing the Windows 2000/XP driver software, you must have the Windows 2000/XP system
installed and running on your computer. You must also have one of the following PenMount 6000
series controller or control boards installed: PM6500, PM6300.
5.1.1 Installing Software(Resistive Touch)
If you have an older version of the PenMount Windows 2000/XP driver installed in your system, please
remove it first. Follow the steps below to install the PenMount DMC6000 Windows 2000/XP driver.
Step 1. Insert the product CD, the screen below would appear. Click touch panel driver.
NP-5xxxA SERIES User Manual
66
Step 2. Select Resistive Touch.
NP
-
5xxA
Step 3. Click Next to continue.
NP-5xxxA SERIES User Manual
67
Step 4. Read the license agreement. Click I Agree to agree the license agreement.
Step 5. Choose the folder in which to install PenMount Windows Universal Driver. Click Install to
start the installation.
NP-5xxxA SERIES User Manual
68
Step 6. Wait for installation. Then click Next to continue.
Step 7. Click Continue Anyway.
NP-5xxxA SERIES User Manual
69
Step 8. Click Finish to complete installation.
NP-5xxxA SERIES User Manual
70
5.1.2 Installing Software (Projected Capacitive)
NP
-
5xxA
NP
-
5xxA
Step 1. Insert the product CD, the screen below would appear. Click touch panel driver.
Step 2. Select Projected Capacitive.
NP-5xxxA SERIES User Manual
71
Step 3. Click Next to continue.
Step 4. Select I accept the terms of the license agreement. Click Next.
NP-5xxxA SERIES User Manual
72
Step 5. Tick Install RS232 interface driver. Click Next.
Step 6. Select None. Click Next.
NP-5xxxA SERIES User Manual
73
Step 7. Click OK.
Step 8. Tick Support Muti-Monitor System. Click Next.
Step 9. Go to C:\Program Files\eGalaxTouch. Click Next.
NP-5xxxA SERIES User Manual
74
Step 10. Click Next.
Step 11. Tick Create a eGalaxTouch Utility shortcut on desktop. Click Next.
NP-5xxxA SERIES User Manual
75
Step 12. Wait for installation.
Step 13. Click Yes to do 4 point calibration.
5.2.1 Software Functions(Resistive Touch)
Upon rebooting, the computer automatically finds the new 6000 controller board. The touch screen is
connected but not calibrated. Follow the procedures below to carry out calibration.
1. After installation, click the PenMount Monitor icon “PM” in the menu bar.
2. When the PenMount Control Panel appears, select a device to “Calibrate.”
PenMount Control Panel(Resistive Touch)
The functions of the PenMount Control Panel are Device, Multiple Monitors ,Tools and About,
which are explained in the following sections.
NP-5xxxA SERIES User Manual
76
Device
In this window, you can find out that how many devices be detected on your system.
Calibrate
This function offers two ways to calibrate your touch screen. ‘Standard Calibration’ adjusts most touch
screens. ‘Advanced Calibration’ adjusts aging touch screens.
Standard Calibration
Advanced Calibration
Click this button and arrows appear
pointing to red squares. Use your finger or
stylus to touch the red squares in
sequence. After the fifth red point
calibration is complete. To skip, press
‘ESC’.
Advanced Calibration uses 4, 9, 16 or 25
points to effectively calibrate touch panel
linearity of aged touch screens. Click this
button and touch the red squares in
sequence with a stylus. To skip, press
ESC’.
NP-5xxxA SERIES User Manual
77
Command Calibration
Command call calibration function. Use
command mode call calibration function,
this can uses Standard, 4, 9, 16 or 25
points to calibrate E.g. Please run ms-dos
prompt or command prompt c:\Program
Files\PenMount Universa Driver\Dmcctrl.exe
-calibration 0 ( Standard Calibration)
Dmcctrl.exe - calibration ($) 0= Standard
Calibration 4=Advanced Calibration 4
9=Advanced Calibration 9 16=Advanced
Calibration 16 25=Advanced Calibration 25
Step 1. Please select a device then click “Configure”. You can also double click the device too.
NP-5xxxA SERIES User Manual
78
Step 2.Click “Standard Calibration” to start calibration procedure
NOTE: The older the touch screen, the more Advanced Mode calibration points you need for an
accurate calibration. Use a stylus during Advanced Calibration for greater accuracy. Please follow the
step as below:
NP-5xxxA SERIES User Manual
79
Step 3.Come back to “PenMount Control Panel” and select Tools then click Advanced
Calibration.
Step 4. Select Device to calibrate, then you can start to do Advanced Calibration.
NOTE: Recommend to use a stylus during Advanced Calibration for greater accuracy.
NP-5xxxA SERIES User Manual
80
Setting
NP-5xxxA SERIES User Manual
81
About
This panel displays information about the PenMount controller and driver version.
NP-5xxxA SERIES User Manual
82
Multiple Monitors
Multiple Monitors support from two to six touch screen displays for one system.
The PenMount drivers for Windows 2000/XP support Multiple Monitors. This function supports
from two to six touch screen displays for one system. Each monitor requires its own PenMount
touch screen control board, either installed inside the display or in a central unit. The PenMount
control boards must be connected to the computer COM ports via the RS-232 interface. Driver
installation procedures are the same as for a single monitor. Multiple Monitors support the
following modes:
Windows Extends Monitor Function
Matrox DualHead Multi-Screen Function
nVidia nView Function
NOTE: The Multiple Monitor function is for use with multiple displays only. Do not use this
function if you have only one touch screen display. Please note once you turn on this
function the rotating function is disabled.
Enable the multiple display function as follows:
1. Check the Enable Multiple Monitor Support box; then click Map Touch Screens to
assign touch controllers to displays.
NP-5xxxA SERIES User Manual
83
2. When the mapping screen message appears, click OK.
3. Touch each screen as it displays “Please touch this monitor”. Following this
sequence and touching each screen is called mapping the touch screens.
4. Touching all screens completes the mapping and the desktop reappears on the
monitors.
5. Select a display and execute the “Calibration” function. A message to start calibration
appears. Click OK.
NP-5xxxA SERIES User Manual
84
6. “Touch this screen to start its calibration” appears on one of the screens. Touch the
screen.
7. “Touch the red square” messages appear. Touch the red squares in sequence.
8. Continue calibration for each monitor by clicking Standard Calibration and touching
the red squares.
NOTES: 1. If you use a single VGA output for multiple monitors, please do not use the
Multiple Monitor function. Just follow the regular procedure for calibration on each
of your desktop monitors.
2. The Rotating function is disabled if you use the Multiple Monitor function.
3. If you change the resolution of display or screen address, you have to redo Map
Touch Screens, so the system understands where the displays are.
About
This panel displays information about the PenMount controller and this driver version.
PenMount Monitor Menu Icon
The PenMount monitor icon (PM) appears in the menu bar of Windows 2000/XP system when you
turn on PenMount Monitor in PenMount Utilities.
NP-5xxxA SERIES User Manual
85
PenMount Monitor has the following function
PenMount Rotating Functions
The PenMount driver for Windows 2000/XP supports several display rotating software packages.
Windows Me/2000/XP support display rotating software packages such as:
• Portrait’s Pivot Screen Rotation Software
• ATI Display Driver Rotate Function
• nVidia Display Driver Rotate Function
• SMI Display Driver Rotate Function
• Intel 845G/GE Display Driver Rotate Function
Configuring the Rotate Function
1. Install the rotation software package.
2. Choose the rotate function (0°, 90°, 180°, 270°) in the 3rd party software. The calibration screen
appears automatically. Touch this point and rotation is mapped.
NOTE: The Rotate function is disabled if you use Monitor Mapping
NP-5xxxA SERIES User Manual
86
5.2.2 Software Functions(Projected Capacitive)
General
In this window, you can see there is USB Controller. Click OK to continue.
Monitor Mapping
to adjust touch panel
Add
to search for device
NP-5xxxA SERIES User Manual
87
Setting
Beep
Beep On Touch
Beep On Release
Beep From System Beep
Beep From Sound Card
Linearization Style
9 points
25 points
Double Click Time
Shorter
Longer
Double Click Area
Smaller
Bigger
Normal mode
Simulate the mouse mode
NP-5xxxA SERIES User Manual
88
Option
Function
Enable Constant Touch
Enable Auto Right Click
Enable Touch
Enable Cursor Stabilization
Constant Touch Area
Auto Right Click Time
NP-5xxxA SERIES User Manual
89
Tools
Click OK to continue the settings.
4 Points Calibration
Do 4 points alignment to match display.
Clear and Calibrate
Clear linearization parameter and do 4 points alignment.
Linearization
Do 9 points linearization for better touchscreen linearity.
Draw Test
Do draw test to verify the touch accuracy.
NP-5xxxA SERIES User Manual
0
Display
In this window, it shows the mode of display.
Enable Multiple Monitors.
Map to main display if system has only one display monitor
Full Screen
Lower Screen
Left Screen
Upper Screen
Right Screen
NP-5xxxA SERIES User Manual
9
91
Other
Other mode of display. Quarter1~4 and Customized area.
Active Area
Drag active area to enable Active Area Function.
NP-5xxxA SERIES User Manual
92
Hardware
Saturn Hardware Configuration
NP-5xxxA SERIES User Manual
93
About
To display information about eGalaxTouch and its version.
NP-5xxxA SERIES User Manual
Loading...