2.1 Wi-Fi / Bluetooth Multi-Room Stereo Speaker
Altavoces Estéreos Wi-Fi / Bluetooth Multihabitación 2.1
Enceinte Stéréo 2.1 Wi-Fi / Bluetooth Multipièce
* Please read the instructions carefully before using the system and keep the manual for future reference.
EVERYWHERE UD-1402
User Manual
Table of Content
Inside the Box
Precaution
Product Introduction
Overview
Connection Options
Standby Mode
LED Indicator
Wi-Fi Connection
Android User
iOS User
PC User
Mac User
Reset Wi-Fi Network (Factory Reset)
Bluetooth Connection
Ethernet Connection
3.5mm Audio Line-In
Troubleshooting
02
03
05
07
08
09
09
10
16
22
30
38
39
41
46
47
01
Inside the Box
Carefully unpack the carton and confirm that the following parts are included.
•
EVERYWHERE Wi-Fi / Bluetooth Speaker
•
AC adaptor
•
Manual
02
Ethernet Connection
Inside the Box
Precaution
03
* Please read these safety instructions carefully to ensure your safety.
•
Do not use this product where contact with moisture, liquids, humidity or rain is possible to avoid
electric shock and operating damage.
•
Avoid exposing this product to direct sunlight, stove tops or any other heat sources to prevent
operating damage.
•
Do not cover the ventilation openings – this may cause overheating, damage to the product, and a
hazardous condition.
•
Do not drop, disassemble, deform, modify or insert any objects into this product as operating damage
will result.
•
Do not attempt to repair, modify or disassemble the product yourself. This product does not contain
any user-serviceable components.
•
Do not clean the product with alcohol, ammonia based cleaners, abrasive cleaners or wet cloth. Only
clean with a soft dry cloth.
•
Do not place this product on its side, on slanted surfaces as well as near the edge of high surfaces,
like shelves. Take care to prevent accidental falling. The product may vibrate while playing music,
which cause it to move and fall off a surface.
•
Do not bring your product in to contact with any sharp objects as this may cause scratches and
operating damage.
•
Observe all signs and displays that require an electrical device or RF radio product to be switched off
in designated areas.
•
Dispose of the product in accordance with local laws and regulations.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates use and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
Precaution
04
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio / TV technician for help.
FCC Notice
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired
operation.
FCC Caution
•
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user‘s authority to operate this equipment.
•
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter.
Industry Canada (IC) Compliance Notice
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device. Under Industry
Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated
power (e.i.r.p.) is not more than that necessary for successful communication.
FCC ID: NKTUD-1402, IC ID: 9092A-UD1402
To locate the FCC and IC identification numbers, please look on the underside of the EVERYWHERE.
Model number UD-1402
The crossed-out wheelie bin symbol means that the product must be disposed of separately in the
European Union. These products must not be disposed of with unsorted household waste.
Precaution
Product Introduction
05
The iui DESIGN UD-1402 “EVERYWHERE” multi-room 2.1 stereo speaker system is a breakthrough in providing
high performance audio to the whole home. You’re in control – you can use one speaker or many. And the
configuration options are almost limitless.
Historically, if you wanted to listen to music from your digital device, you could connect to your speaker with a
3.5mm audio cable, or Bluetooth. But EVERYWHERE provides you breakthrough flexibility. While it connects via
an audio cable and Bluetooth, it also can connect by Wi-Fi and wired Ethernet.
And by using Wi-Fi or wired Ethernet, you can create a whole home audio system, so that you have music
distributed throughout your home.
To get the best experience from EVERYWHERE, it’s good to understand some basics. First and foremost, you
can simply connect the product by using the 3.5mm audio line in or Bluetooth if you want to just connect one
digital device to the speaker. But to play your music to more than one speaker, you need to take a few additional
steps. But, let’s first walk through the basics…
Since EVERYWHERE is a very high-performance speaker system with amazing technology capability, you have
options to meet your lifestyle. First, you need to decide how to connect your digital devices to the product, and
what the trade-offs are for each type of connection.
3.5mm Audio Line-in:
If you use the 3.5mm stereo audio line in, you can simply connect your audio source to EVERYWHERE, and you
can enjoy high performance audio. Of course, you will be limited to one EVERYWHERE and you have to remain
physically connected.
Bluetooth:
Bluetooth is a simple wireless connection to connect your digital source to your EVERYWHERE. Bluetooth
technology only connects from one source (your digital source, like a PC or Smartphone) to one speaker, such as
EVERYWHERE. And Bluetooth has lower sound performance than a wired 3.5mm audio connection, due to
compression of the signal during wireless transmission. Its range is also limited, typically to one room.
Wi-Fi:
Using Wi-Fi, you can connect your Wi-Fi digital source (such as your PC, Mac, tablet, smartphone, etc) to one or
Product Introduction
06
more EVERYWHERE speakers. The benefit of Wi-Fi over Bluetooth is important – Wi-Fi allows you to stream one
source to EVERYWHERE speakers all over your house (because Wi-Fi typically has longer range), and the
bandwidth of Wi-Fi is much higher than Bluetooth, so the quality of the sound performance is essentially the same
as a 3.5mm wired audio connection.
Of course, Wi-Fi performance in the home is influenced by many factors – the quality of your wireless router, how
many people are connected to the router and downloading at the same time, the number of routers that are
active (which is really important in high-density housing such as apartment buildings).
In general, we recommend a maximum of three EVERYWHERE speakers connected to your router. More is
possible if you take certain technical steps to improve your bandwidth – but that discussion is beyond the scope
of this manual.
And Wi-Fi performance is impacted by the capability of your Wi-Fi enable digital device – for example, an iOS
based product such as an iPhone can only reliably connect to one Wi-Fi device at a time. But if you use iTunes on
your PC or Mac, you can connect to multiple EVERYWHERE speakers. You can also use Android smartphones,
tablets and PC’s to connect using a standard known as DLNA, and connects to multiple EVERYWHERE
speakers.
Wired Ethernet:
Wired Ethernet, where the EVERYWHERE is connected to your router or Ethernet switch with an Ethernet cable
will give you the best performance. You can typically connect many more than three EVERYWHERE speakers.
Ultimately, there is a limitation of your router or Ethernet switch, but for most standard residential users this is not
a factor. And wired Ethernet will give you the audio performance of a 3.5mm wired connection.
So the first decision you will have to make is how you want to connect to EVERYWHERE. Once you make that
decision, then you can follow the easy steps in this manual to start enjoying your music.
If you are using an iPhone or /and Android device, we have an app that makes it easy to set-up your
EVERYWHERE. You can use the app to connect the EVERYWHERE to your home network, you can name it
(Living Room, Kitchen, Den), and you can assign EVERYWHERE speakers to groups, so that you can play your
music to one, some or all EVERYWHERE speakers.
The EVERYWHERE application also updates the software on your EVERYWHERE speaker, keeping it current and
up to date. The EVERYWHERE application does not take the place of your music player software, such as iTunes,
Windows Media Player or streaming music service applications such as Pandora. The application lets you
configure your EVERYWHERE speakers, and then you use your favorite applications to select and play music.
Product Introduction
5
6 7 8 9
4
1 23
07
Overview
1. Bluetooth pairing
2. Volume up
3. Volume down
4. NFC sensor
5. LED indicator
6. DC jack
7. 3.5mm audio line-in
8. RJ45 Ethernet jack
9. Power / Bluetooth Mode /
Wi-Fi & Ethernet Mode
Overview
08
Connection Options
EVERYWHERE UD-1402 provides 4 options for connecting to your music
source: 2 wireless and 2 wired connections.
A. Wi-Fi - Wireless Connection
For setup, see the section “Wi-Fi Connection”.
B. Bluetooth - Wireless Connection
For setup, see the section “Bluetooth Connection”.
C. RJ45 - Wired Ethernet Connection
For setup, see the section “Ethernet Connection”.
D. 3.5mm audio line-in - Wired Connection
For setup, see the section “3.5mm Audio Line-In”.
Connection Options
09
Standby Mode
EVERYWHERE will enter standby mode under any of the following situations:
•
No Wi-Fi connection for 20 minutes;
•
No Bluetooth connection for 20 minutes;
•
No 3.5mm audio line-in or Ethernet connection for 20 minutes or;
•
Press and hold for 5 seconds in any mode.
To resume normal operation, press once.
LED Indicator
LED off
Red
Red (flashing)
Purple
Green (flashing)
Green
Blue
Blue (flashing)
Amber
Power off
Power on
No connections detected
(3.5mm / Bluetooth / Wi-Fi/ Ethernet)
Wi-Fi mode + Connected to your device
(During setup Wi-Fi Connection)
Wi-Fi mode + Connecting to your network
(The connection will complete automatically)
Wi-Fi mode + Connected to your Wi-Fi network
Power on + Bluetooth Connection
Power on + Bluetooth pairing mode
Power on + Wired connection
(3.5mm audio line or Ethernet cable)
Standby Mode \ LED Indicator
Before Setup
Please download the iui DESIGN Wi-Fi Audio App to
setup the wireless connection between EVERYWHERE
and your Wi-Fi network. Through the app, there are
step-by-step instructions to guide you through the app.
The app is available for free in Google Play.
Please make sure your device is connected to the
same Wi-Fi network where EVERYWHERE will be
located. Otherwise, an error message will appear
after entering password as the app cannot detect
EVERYWHERE in the current Wi-Fi network.
Wi-Fi Connection - Android User
10
Wi-Fi Connection - Android User
11
Wi-Fi Connection - Android User
1 2
Connect EVERYWHERE to a power
source. Slide the power switch to
“Wi-Fi” position.
Launch the app on your device.
Press to start the setup
procedure.
4
4
4
Go back to the app and select your
Wi-Fi network inside the app.
3
Open the Wi-Fi setting page on your
device. Turn on the Wi-Fi feature and
select “EVERYWHERExxxx”* from
the list of available wireless
networks*.
Setup
12
Wi-Fi Connection - Android User
6
Rename your EVERYWHERE for
easy recognition (suggested).
Tap to confirm.
5
Enter password for your Wi-Fi
network you chose#. The LED
indicator turns to solid green.
EVERYWHERE_Room
* If the EVERYWHERE could not be found in the list, follow the section
“Reset Wi-Fi Connection” to reset the speaker to factory default and try
again.
#
In case of incorrect password or failed connection, follow the section
“Reset Wi-Fi Connection” to reset the speaker to factory default and start
the setup procedure again.
13
Wi-Fi Connection - Android User
Setting Up Multiple EVERYWHERE Speakers
If you have more than one EVERYWHERE, please follow the same setup
procedures one-by-one and rename each EVERYWHERE speaker right after
setup to avoid confusion.
Changing the Wi-Fi network of EVERYWHERE
Clear the current Wi-Fi setting of EVERYWHERE. See the section “Reset
Wi-Fi Connection” for detailed instructions.
Streaming Music
If you want to stream music from an Android device, you should download a
DLNA compatible player for streaming music. Select EVERYWHERE (which
may appear with the name you assigned) as your audio output device in the
music player. Different players may have different setups, please refer to those
corresponding user guides for detail.
* Please make sure your Android device is connected to the same Wi-Fi
network as EVERYWHERE is located.
14
Wi-Fi Connection - Android User
Advanced Setting
Rename Your Speaker
“Rename your speaker” allows easy recognition of which EVERYWHERE you
are playing. Names such as Kitchen, Family Room, etc are quite logical, but
it’s your choice.
EVERYWHERE_Bathroom
EVERYWHERE_Room
EVERYWHERE_Kitchen
EVERYWHERE_Room
EVERYWHERE_Kitchen
EVERYWHERE_Bathroom
You can rename your speaker by
tapping on the speaker from the
list inside the app.
Click to save changes.
Or, click to discard changes.
Multi-Room
“Multi-Room” allows grouping
speakers play together from the
same music source.
Slide the button to group the
speakers. *Up to 3 speakers for
stable connection.
15
Wi-Fi Connection - Android User
Audio Channel
“Audio Channel” setting allows different
speakers to play in different audio channels:
Left (L) / Right (R) / Stereo (L+R).
Using this function, you can create your
own stereo pairs. You could put two
EVERYWHERE speakers in a room, and
direct the left stereo signal to the left unit,
and the right stereo signal to the right unit.
In this mode, EVERYWHERE automatically
switches internally to become a higher
power mono speaker, playing only one
channel.
EVERYWHERE_Bathoom
EVERYWHERE_Kitchen
EVERYWHERE_Room
EVERYWHERE_Bathoom
EVERYWHERE_Kitchen
EVERYWHERE_Room
EVERYWHERE_Bathoom
EVERYWHERE_Kitchen
EVERYWHERE_Room
Firmware Update
“Firmware Update” allows updating the
firmware of EVERYWHERE maintain
the best product performance. The
sign means there is update
available. It is strongly recommended
that you always update your firmware,
and regularly check to see if an update
is available.
* Please keep stable network
connection during firmware update.
Slide the button to group the
speakers. Select which channel
you wish to play for the speaker.
Tap on the speaker you wish to
update. Press button.
Because of the limitation in the iOS (iPhone) as noted
in the introduction, you can connect only one
EVERYWHERE speaker reliably to an iPhone. Of
course, you can use iTunes on a Mac or PC and
connect to more than one EVERYWHERE unit.
Before Setup
Please download the iui DESIGN Wi-Fi Audio App to
setup the wireless connection between EVERYWHERE
and your Wi-Fi network. Through the app, there are
step-by-step instructions to guide you through the
app. The app is available for free in App Store.
Please make sure your device is connected to the
same Wi-Fi network where EVERYWHERE will be
located. Otherwise, an error message will appear after
entering password as the app cannot detect
EVERYWHERE in the current Wi-Fi network.
Wi-Fi Connection - iOS User
16
Wi-Fi Connection - iOS User
Settings Wi-Fi
Wi-Fi
EVERYWHERExxxx
CHOOSE A NETWORK
NETWORK_ROUTER
1 2
Connect EVERYWHERE to a power
source. Slide the power switch to
“Wi-Fi” position.
Launch the app on your iOS device.
Press button to start the
setup procedure.
4
4
4
Go back to the app and select your
Wi-Fi network inside the app.
3
Open the Wi-Fi setting page on your
device.
Turn on the Wi-Fi feature and select
“EVERYWHERExxxx” from the list of
available wireless networks*.
Setup
17
Wi-Fi Connection - iOS User
EVERYWHERE_Room
6
Rename your EVERYWHERE for
easy recognition (suggested).
Tap to confirm.
5
Enter password for your Wi-Fi
network you chose#. The LED
indicator turns to solid green.
* If the EVERYWHERE could not be found in the list, follow the section “Reset
Wi-Fi Connection” to reset the speaker to factory default and try again.
#
In case of incorrect password or failed connection, follow the section
“Reset Wi-Fi Connection” to reset the speaker to factory default and start
the setup procedure again.
18
Wi-Fi Connection - iOS User
19
Wi-Fi Connection - iOS User
Setting up Multiple EVERYWHERE Speakers
If you have more than one EVERYWHERE, please follow the same setup
procedures one-by-one and rename each EVERYWHERE speaker right after
setup to avoid confusion. Remember that connecting an iOS device (iPhone)
to more than one EVERYWHERE (or other Wi-Fi speakers) may create an
unstable connection.
Changing the Wi-Fi network of EVERYWHERE
Clear the current Wi-Fi setting of EVERYWHERE See the section “Reset
Wi-Fi Connection” for detailed instructions.
Streaming Music
For an iOS user, you can use AirPlay to
stream music to EVERYWHERE*.
To stream music via AirPlay:
1. Launch your music player
2. Tap on AirPlay
3. Choose “EVERYWHERE”
(If you renamed it, it will appear with
the name you assigned)
* Please make sure your device is connected to the same Wi-Fi network as
EVERYWHERE is located.
EVERYWHERE_Bathroom
EVERYWHERE_Room
EVERYWHERE_Kitchen
EVERYWHERE_Bathroom
EVERYWHERE_Room
EVERYWHERE_Kitchen
Advanced Setting
Rename Your Speaker
“Rename your speaker” allows easy recognition of which EVERYWHERE you
are playing. Names such as Kitchen, Family Room, etc are quite logical, but
it’s your choice.
You can rename your speaker by
tapping on the speaker from the
list inside the app.
Click to save changes.
Or, click to discard changes.
Multi-Room
“Multi-Room” allows grouping
speakers play together from the same
music source. Slide the button to
group the speakers. *Multi-Room is not
stable for iPhone user due to iPhone
limitation. For other iOS devices, it can
connect reliably up to 3 speakers.
20
Wi-Fi Connection - iOS User
21
Wi-Fi Connection - iOS User
Audio Channel
“Audio Channel” setting allows different
speakers to play in different audio channels:
Left (L) / Right (R) / Stereo (L+R).
Using this function, you can create your
own stereo pairs. You could put two
EVERYWHERE speakers in a room, and
direct the left stereo signal to the left unit,
and the right stereo signal to the right unit.
In this mode, EVERYWHERE automatically
switches internally to become a higher
power mono speaker, playing only one
channel.
Slide the button to group the
speakers. Select which channel
you wish to play for the speaker.
Firmware Update
“Firmware Update” allows updating the
firmware of EVERYWHERE maintain
the best product performance. The
sign means there is update
available. It is strongly recommended
that you always update your firmware,
and regularly check to see if an update
is available.
* Please keep stable network
connection during firmware update.
EVERYWHERE_Room
EVERYWHERE_Bathoom
EVERYWHERE_Kitchen
EVERYWHERE_Room
EVERYWHERE_Bathoom
EVERYWHERE_Kitchen
EVERYWHERE_Room
EVERYWHERE_Bathoom
EVERYWHERE_Kitchen
Tap on the speaker you wish to
update. Press button.
Wi-Fi Connection - PC User
22
Wi-Fi Connection - PC User
Before Setup
If you use an Ethernet cable for setup
Please prepare a RJ45 Ethernet cable for setup.
If you use Wi-Fi for setup
Please make sure your PC is connected to the same Wi-Fi network where
EVERYWHERE will be located. Otherwise, the connection will not be
established because your PC will not detect EVERYWHERE in the current
Wi-Fi network.
23
Wi-Fi Connection - PC User
1
Connect EVERYWHERE
to a power source. Slide
the power switch to the
“Wi-Fi” position.
Connect EVERYWHERE to your PC:
4
2
Use an Ethernet cable to connect
EVERYWHERE and your PC. Your
PC takes approximately 30 seconds
to establish connection with
EVERYWHERE. The LED indicator
will turn to solid amber once the
connection is completed.
Search and connect
“EVERYWHERExxxx” in Wi-Fi
setting page*. The LED indicator
will turn to solid purple once the
connection is completed.
Setup
or
24
Wi-Fi Connection - PC User
3 4
Browse the below link on your
device to enter the setup page:
http://192.168.6.1/
Select “Connect to Home” >
“Wireless” in the setup page.
5 6
Select your Wi-Fi network. Enter password for your Wi-Fi
network you chose and Click
“Join”.
25
Wi-Fi Connection - PC User
7
Click “Done” and remove the
Ethernet cable if you use it for
setup#.
* If the EVERYWHERE could not be found in the list, follow the section
“Reset Wi-Fi Connection” to reset the speaker to factory default and try
again.
#
In case of incorrect password or failed connection, follow the section “Reset
Wi-Fi Connection” to reset the speaker to factory default and start the
setup procedure again.
Setting up Multiple EVERYWHERE
If you have more than one EVERYWHERE speaker, please follow the same
setup procedures and rename one by one right after setup to avoid unnecessary
confusion. Please download the iui DESIGN Wi-Fi Audio App to rename
EVERYWHERE. The app is available for free in Google Play and App Store.
Changing the Wi-Fi network of EVERYWHERE
Clear the current Wi-Fi setting of EVERYWHERE See the section “Reset
Wi-Fi Connection” for detailed instructions.
Streaming Music
For a PC device, Windows Media Player 11 and above can be used to stream
music to EVERYWHERE through "Play To" feature. Use "Play To" on your
music library from Windows Media Player. For detail instruction for "Play To"
feature, please consult the user manual for your specific device.
26
Wi-Fi Connection - PC User
27
Wi-Fi Connection - PC User
Advanced Setting
For advanced settings, including “Rename Your Speaker”, “Multi-Room”
and “Audio Channel”, please download the iui DESIGN Wi-Fi Audio App and
see “Advanced Setting” section for corresponding device (Android / iOS).
The app is available for free in Google Play and App Store.
28
Wi-Fi Connection - PC User
Firmware Update
“Firmware Update” allows updating the firmware of EVERYWHERE maintain
the best product performance. It is strongly recommended that you always
update your firmware, and regularly check to see if an update is available.
1 2
3 4
Connect your PC to the Wi-Fi
network where
EVERYWHERE is located.
Open “Your Neighborhood
Network”.
Double click EVERYWHERE
to enter setup page.
Click “Others…” .
29
Wi-Fi Connection - PC User
5 6
Click “Firmware Upgrade”. Click “Check Update”.
Click “Update” if there is
available update.
* Please keep stable network connection during firmware upgrade.
30
Wi-Fi Connection - Mac User
Wi-Fi Connection - Mac User
Before Setup
If you use an Ethernet cable for setup
Please prepare a RJ45 Ethernet cable for setup.
If you use Wi-Fi for setup
Please make sure your Mac is connected to the same Wi-Fi network where
EVERYWHERE will be located. Otherwise, the connection will not be
established because your PC will not detect EVERYWHERE in the current
Wi-Fi network.
31
Wi-Fi Connection - Mac User
Connect EVERYWHERE to your Mac:
1
Connect EVERYWHERE
to a power source. Slide
the power switch to
“Wi-Fi” position.
4
2
Use an Ethernet cable to connect
EVERYWHERE and your Mac.
Your Mac takes approximately 30
seconds to establish connection
with EVERYWHERE. The LED
indicator will turn to solid amber
once the connection is completed.
Search and connect
“EVERYWHERExxxx” in Wi-Fi
setting page*. The LED indicator
will turn to solid purple once the
connection is completed.
Setup
or
32
Wi-Fi Connection - Mac User
3 4
Browse the below link on your
device to enter the setup page:
http://192.168.6.1/
Select “Connect to Home” >
“Wireless” in the setup page.
5 6
Select your Wi-Fi network. Enter password for your Wi-Fi
network you chose and Click
“Join”.
33
Wi-Fi Connection - Mac User
7
Click “Done” and remove the
Ethernet cable if you use it for
setup#.
* If the EVERYWHERE could not be found in the list, follow the section
“Reset Wi-Fi Connection” to reset the speaker to factory default and try
again.
#
In case of incorrect password or failed connection, follow the section “Reset
Wi-Fi Connection” to reset the speaker to factory default and start the
setup procedure again.
Setting up Multiple EVERYWHERE
If you have more than one EVERYWHERE speaker, please follow the same
setup procedures and rename one by one right after setup to avoid unnecessary
confusion. Please download the iui DESIGN Wi-Fi Audio App to rename
EVERYWHERE. The app is available for free in Google Play and App Store.
Changing the Wi-Fi network of EVERYWHERE
Clear the current Wi-Fi setting of EVERYWHERE See the section “Reset
Wi-Fi Connection” for detailed instructions.
34
Wi-Fi Connection - Mac User
35
Wi-Fi Connection - Mac User
Streaming Music
You can use iTunes to stream music to EVERYWHERE*.
To stream music via iTunes:
1. Launch iTunes
2. Click AirPlay
3. Choose “EVERYWHERE”
(If you renamed it, it will
appear with the name you
assigned)
* Please make sure your device is connected to the same Wi-Fi network as
EVERYWHERE is located.
Advanced Setting
For advanced settings, including
“Rename Your Speaker”, “Multi-Room”
and “Audio Channel”, please download
the iui DESIGN Wi-Fi Audio App and see
“Advanced Setting” section for
corresponding device (Android / iOS). The
app is available for free in Google Play and
App Store.
Firmware Update
“Firmware Update” allows updating the firmware of EVERYWHERE maintain
the best product performance. It is strongly recommended that you always
update your firmware, and regularly check to see if an update is available.
36
Wi-Fi Connection - Mac User
1 2
3 4
Open “Safari”.
Select “Preferences…” in Safari
toolbar.
Click “Advanced” and check
the box for “Include Bonjour
in the Favorites bar”.
Select “Bonjour > Webpages >
EVERYWHERE” to enter setup
page.
Connect your Mac to the
Wi-Fi network where
EVERYWHERE is located.
37
Wi-Fi Connection - Mac User
5 6
Click “Others…” . Click “Firmware Upgrade”.
7
Click “Check Update”.
Click “Update” if there is
available update.
* Please keep stable network
connection during firmware
upgrade.
Wi-Fi Connection -
Reset Wi-Fi Connection
Factory Reset
If you wish to connect EVERYWHERE to another Wi-Fi network or you could
not find EVERYWHERE in the list of available wireless networks in Wi-Fi
Setting page, you need to reset the Wi-Fi connection. After restoring the
factory setting, the name of speaker will be set as “EVERYWHERE”.
To reset the Wi-Fi network, follow the below instructions:
* The Factory Reset only applies to Wi-Fi mode with no 3.5mm line-in connection. If you
want to reset to the factory default, please disconnect the 3.5mm audio line in cable.
38
Wi-Fi Connection - Reset Wi-Fi Connection (Factory Reset)
1 2
Connect EVERYWHERE to power
source. Slide the power switch to
“Wi-Fi” or the Bluetooth position.
Press and hold , and for 4
seconds. The LED indicator will flash
red 4 times to indicate that the
factory reset is done.
39
Bluetooth Connection
You can setup the wireless connection between EVERYWHERE and your
Bluetooth enabled device by setting or NFC (for NFC enabled device only).
By Setting - Bluetooth Connection
1. Connect EVERYWHERE to a power source.
2. Slide the power switch to the Bluetooth position.
3. Press and hold to activate Bluetooth
pairing mode.
4. Turn on the Bluetooth feature on your device.
5. Search “EVERYWHERE” and select.
6. Confirm pairing and the LED indicator turns to solid blue.
Bluetooth Connection
40
By NFC - Bluetooth Connection - for NFC enabled device only
1. Connect EVERYWHERE to a power source.
2. Slide the power switch to the Bluetooth position.
3. Turn on the NFC feature on your device.
4. Tap on the NFC sensor for pairing.
5. Confirm pairing and the LED indicator turns
to solid blue.
Stream Music
You can stream music to EVERYWHERE from any music sources on the
connected device via Bluetooth.
Bluetooth Connection
41
Ethernet Connection
Before Setup
Please prepare a RJ45 Ethernet cable and a PC / Mac which has Wi-Fi
feature for setup.
Setup
1
Connect EVERYWHERE to a
power source. Slide the power
switch to the “Wi-Fi” position.
2
Search and connect
“EVERYWHERExxxx” in Wi-Fi
setting page*. The LED indicator
will turn to solid purple once the
connection is completed.
Ethernet Connection
42
3 4
Browse the below link on your
device to enter the setup page:
http://192.168.6.1/
Select “Connect to Home” >
“LAN” in the setup page.
5
Click “Join”.
Use an Ethernet cable to connect EVERYWHERE and your Wi-Fi router.
Ethernet Connection
43
* If the EVERYWHERE could not be found in the list, follow the section
“Reset Wi-Fi Connection” to reset the speaker to factory default and try
again.
#
In case of incorrect password or failed connection, follow the section “Reset
Wi-Fi Connection” to reset the speaker to factory default and start the
setup procedure again.
6
Click “Done”. The LED indicator
will turn to solid amber once the
connection is completed.
Ethernet Connection
44
Setting Up Multiple EVERYWHERE Speakers
If you have more than one EVERYWHERE, please follow the same setup
procedures one-by-one and rename each EVERYWHERE speaker right after
setup to avoid confusion.
Changing the Wi-Fi network of EVERYWHERE
Clear the current Wi-Fi setting of EVERYWHERE See the section “Reset Wi-Fi
Connection” for detailed instructions.
Streaming Music
Stream music from an Android device:
See the section “Streaming Music” under “Wi-Fi Connection - Android
User” for detailed instructions.
Stream music from an iOS device:
See the section “Streaming Music” under “Wi-Fi Connection - iOS User”
for detailed instructions.
Stream music from a PC:
See the section “Streaming Music” under “Wi-Fi Connection - PC User”
for detailed instructions.
Stream music from a Mac:
See the section “Streaming Music” under “Wi-Fi Connection - Mac User”
for detailed instructions.
44
Ethernet Connection
45
Advanced Setting
For advanced settings, including “Rename Your Speaker”, “Multi-Room”
and “Audio Channel”, please download the iui DESIGN Wi-Fi Audio App and
see “Advanced Setting” section for corresponding device (Android / iOS). The
app is available for free in Google Play and App Store.
Firmware Update
“Firmware Update” allows updating the firmware of EVERYWHERE maintain
the best product performance. The sign means there is update available. It is
strongly recommended that you always update your firmware, and regularly
check to see if an update is available.
Update the firmware using an Android device:
See the section “Firmware Update” under “Wi-Fi Connection - Android
User” for detailed instructions.
Update the firmware using an iOS device:
See the section “Firmware Update” under “Wi-Fi Connection - iOS User”
for detailed instructions.
Update the firmware using a PC:
See the section “Firmware Update” under “Wi-Fi Connection - PC User”
for detailed instructions.
Update the firmware using a Mac:
See the section “Firmware Update” under “Wi-Fi Connection - Mac User”
for detailed
Ethernet Connection
3.5mm Audio Line-In Connection
1. Connect EVERYWHERE to a power source.
2. Slide the power switch to the Bluetooth or “Wi-Fi” position.
3. Connect EVERYWHERE to your device with a 3.5mm audio line-in cable.
4. The LED indicator will turn to solid amber when the 3.5mm audio line-in
cable is detected.
Important Note: The EVERYWHERE speaker will always default to the 3.5mm
audio line in. So if you are using it in the Wi-Fi or Bluetooth mode, and you
plug in a 3.5mm audio line it, the speaker will automatically switch to the
3.5mm audio line in.
Streaming Music
You can play music to EVERYWHERE from any music
source on a connected device via 3.5mm audio line-in.
46
3.5mm Audio Line-In
Trouble Shooting
I cannot find EVERYWHERE in the Wi-Fi setting page
•
Please make sure EVERYWHERE is connected to a power source properly
and the power switch is in the “Wi-Fi” position. If EVERYWHERE is still does
not appear on the Wi-Fi setting page, you can should EVERYWHERE to
factory setting and try again. See the section “Reset Wi-Fi Connection” for
detailed instruction.
I have finished setup EVERYWHERE, but I cannot see it in the app.
•
Please make sure you are connected to the same Wi-Fi network where
EVERYWHERE is connected and the EVERYWHERE is connected to power
and the power switch is in the “Wi-Fi” position.
I use the app for setup and I have entered the correct password, but it shows
an error message.
•
Please make sure your device is connected to the same network where
EVERYWHERE is connected. If your device that is running the app is
connected to a different Wi-Fi network than the EVERYWHERE is connected
to, it will show an error message because it cannot connect to the
EVERYWHERE.
47
Troubleshooting
48
© 2014 IUI Audio Inc. (United States) or Platform2 International Limited (other
countries). All rights reserved. The iui DESIGN brand, logo and other marks
under iui DESIGN are owned and registered by IUI Audio Inc. (United States)
or Platform2 International Limited (other countries). The Bluetooth
®
word mark
and logos are registered trademarks owned by Bluetooth SIG, Inc. Other
trademarks and trade names are registered mark of their respective owners.
Printed in China
Troubleshooting
Loading...