TM
600L Icicle Light Set
IMPORTANT SAFETY INSTRUCTIONS
600 (3x200L) Mini iTwinkle light show Item Number: 00610
When using electrical products, basic precautions should always be
followed including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
• This is an electrical product - not a toy! To avoid the risk of fire, burns, personal
injury and electric shock it should not be played with or placed where small
children can reach it.
• Do not use seasonal products outdoors unless marked suitable for indoor and
outdoor use. When products are used in outdoor applications, connect the
product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not
provided contact a qualified electrician for proper installation.
• This seasonal use product is not intended for permanent installation or use.
• Do not mount or place near gas or electric heaters, fireplaces, candles or other
similar sources of heat.
• Do not secure the wiring of the product with staples or nails, or place on sharp
hooks or nails.
• Do not let lamps rest on the supply cord or on any wire.
• Unplug the product when leaving the house, when retiring for the night, or if left
unattended.
• Do not use this product for other than its intended use.
• Do not hang ornaments or other objects from cord, wire, or light string.
• Do not place lighting string on carpeting, drapes, furniture or allow it to contact
vinyl siding while the power is on.
• Do not perform any maintenance or troubleshoot for bad/broken lamps while
the power is on.
• Do not close doors or windows on the product or extension cord as this may
damage the wire insulation.
• Do not cover the product with cloth, paper or any material not part of the
product when in use.
• This product has a polarized plug (one blade is wider than the other) as a
feature to reduce the risk of electric shock. This plug will fit in a polarized outlet
only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician. Do not use with an extension cord
unless plug can be fully inserted. Do not alter or replace the plug.
• This product is equipped with push-in type lamps. Do not twist lamps
• This product employs overload protection (fuse). A blown fuse indicates an
overload or short-circuit situation. If the fuse blows, unplug the product from
the outlet. Also, unplug any additional strings or products that may be
attached to the product. Replace the fuse as per the User Servicing
instructions (follow product marking for proper fuse rating) and check the
product. If the replacement fuse blows, a short-circuit may be present and the
product should be discarded.
• Read and follow all instructions that are on the product or provided with the
product.
SAVE THESE INSTRUCTIONS
USE AND CARE INSTRUCTIONS
• When the product is placed on a live tree, the tree should be well maintained
and fresh. Do not place on live trees in which the needles are brown or break
off easily. Keep the tree holder filled with water.
USE AND CARE INSTRUCTIONS (Continued)
• If the product is placed on a tree, the tree should be well secured and stable.
• Before using, or reusing, inspect product carefully. Discard any products that
have cut, damaged or frayed wire insulation or cords, cracks in the
lampholders or enclosures, loose connections, or exposed copper wire.
• When storing the product, carefully remove the product from wherever it is
placed, including trees, branches, or bushes, to avoid any undue strain or
stress on the product conductors, connections and wires.
• When not in use, store neatly in a cool, dry location protected from sunlight.
USER SERVICING INSTRUCTIONS
String Set Fuse Replacement: Most often fuses blow because too many
sets have been strung end-to-end,
a) Before changing fuses, make sure the set is unplugged.
b) Grasp plug and remove from the receptacle or other outlet device. Do not
unplug by pulling on cord.
c) Using a flathead screwdriver, open fuse cover. Slide
open the fuse access cover on top of attachment plug
towards blades.
d) Remove fuses carefully.
e) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse
(provided with product).
f) Close fuse cover. Slide closed the fuse access cover on top of attachment
plug. Make sure door is fully closed and fuses are completely covered.
g) Risk of fire. Do not replace attachment plug. Contains a safety device
(fuse) that should not be removed. Discard product if the attachment plug
is damaged.
Control Box Plug Fuse Replacement: Replace the fuse.
a) Grasp the plug and remove from the receptacle or other outlet device. Do
not unplug by pulling on cord.
b) Using a flathead screwdriver, open fuse cover.
Slide open the fuse access cover on top of
attachment plug towards blades.
c) Remove fuses carefully.
d) Risk of fire. Replace fuse only with 5 Amp, 125
Volt fuse (provided with product).
e) Close fuse cover. Slide closed the fuse access cover on top of attachment
plug. Make sure door is fully closed and fuses are completely covered.
f) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse)
that should not be removed. Discard product if the attachment plug is
damaged.
Replace Steady Bulb: Before changing bulbs, make sure set is unplugged.
Replace Steady Bulb (Continued)
If the spare bulbs provided with the product have no plastic base or the plastic
base does not fit, first follow a)-b) above. Then 1) Remove the old bulb by
straightening the bulb wires and pulling bulb straight from
the base. (Fig. a), 2) Replace the new bulb by
straightening the bulb leads and aiming each wire into a
separate hole in the plastic base (Fig. b), 3) Make sure
each bulb lead comes out an exit opening at the bottom of
the plastic base. Now bend each lead up such that each bulb lead fits closely
against the narrow side and in the center of the plastic base (Fig. c).
CAUTION:
• To reduce the risk of fire and electric shock:
a) Do not install on trees having needles, leaves or branch coverings of metal or
materials which look like metal, and
b) Do not mount or support strings in a manner that can cut or damage wire
insulation.
• To reduce the risk of overheating, replace burned-out lamps promptly. Use 2.5
Volt, 0.35 Watt lamps only.
• This lighting string is rated 204 Watts (1.7 Amps), do not overload. Connect other
lighting strings or decorative outfits end-to-end to a maximum of 420 watts (3.5
Amps) total. If connecting to a lighting string that does not have a Wattage (W)
rating (found on the tag 6 inches of the plug) calculate the wattage as follows:
Multiply the current (__ A) which is on the flag-type tag by 120.
For Example: Lighting string is rated 120 V, 60Hz, 0.2 Amps. 0.2 x 120 = 24
Watts. Add the wattage of each lighting string together for a total of 420 Watts or
less. (Do not exceed 420 Watts.)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
▪ this device may not cause harmful interference, and
▪ this device must accept any interference received, including interference
that may cause undesired operation.
Modifications not approved by the party responsible for compliance could
void user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and the receiver.
* Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
* Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any Changes or Modifications not expressly approved by the
party responsible for compliance could void user’s authority to operate this
equipment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.
(See other side for Operating Instructions)