Ittim Technology SD06 User Manual

SD06-S14PXX0000NV1
Product Specification
802.11b/g/n Module
Version 1.0
Document
release
Version 1.0 2016-04-27 Initial release
Date Modification Approved
CONTENTS
1. General Description .................................................................................................................. 1
2. Module Hardware Overview ..................................................................................................... 1
2.1 Features ..................................................................................................................... 1
2.2 Interface .................................................................................................................... 1
3.Electrical Specification .................................................................................................................. 3
3.1 DC Characteristics .................................................................................................... 3
3.2 Environment Storage Condition ................................................................................ 3
4. RF Specification ........................................................................................................................ 4
4.1 Rx Characteristics ..................................................................................................... 4
4.2 Tx Characteristics...................................................................................................... 4
5.Mechanical Specifications ............................................................................................................. 5
6.FCC Caution. ................................................................................................................................. 5
7.Host Antenna Connectors ............................................................................................................... 7
8.Instructions on the using of the module ......................................................................................... 8
1. General Description
The SD06-S14PXX0000NV1is most powerful Low-Power embedded Wi-Fi Module and
target to smart household electrical appliance. The module support IEEE 802.11b/g/n protocol,
includes a number of TCP/IP-based connectivity protocols along with SSL,enabling a
low-cost,low-complexity system to obtain full-featured internet connectivity and reliable
information exchange.With SD06-S14PXX0000NV1 module,the traditional devices can easily
access to the
wireless network through SDIO.
The module is based on Marvell SD06-S14PXX0000NV1 which is highly integrated, and
includes an energy efficient on-board power amplifier and LNA.
2. Module Hardware Overview
2.1 Features
IEEE802.11b/g/n (1x1) wireless standards
SD06-S14PXX0000NV1 solutions for smart energy and building automation
Support work as STA/AP mode
Support OTA and Remote Firmware Upgrade
Module is powered by the host with a 3.3V +/- 10% supply.
One U.FL antenna connector inside the module
4 layers through hole PCB design with FR4 material
2.2 Interface
Interface
1.5 mm pitch connector
Antenna: IPEX connector
Pin definition
Pin
Number
1 SD-D2 I
Symbol Name Status
From Module TOP View
Pin Description
SDIO DATA D2
2 SD-D3 I/O
SDIO DATA D3
3
4
5
6
7 SD-D1 I/O SDIO DATA D1
8 +3.3V I/O POWER 3.3V
9 PDN I/O General Purpose I/O
10 GND P GND
11 RF-ANT RF-ANT
12
13 WK-IN I/O General Purpose I/O
14
SD-CMD I/O SDIO CMD
GND P GND
SD-CLK I/O SDIO CLK
SD-D0 I/O SDIO DATA D0
GND P
WK-OUT I/O General Purpose I/O
3.Electrical Specification
`
Element
DC supply voltage
3.1
3.1 DC Characteristics
3.13.1
Symbol
- 3.3 3.63 (V)
STBY
3.3V
3.2
3.2 Environment Storage Condition
3.23.2
Standby(CHIP_PWD) -- -- (uA)
Standby(SUSPEND) -- 10 -- (uA)
Continuous Tx Current 2.4GHz -- 90 (mA)
Continuous Rx Current 2.4GHz -- 60 (mA)
Temperature
Humidity
Symbol Min Typ Max Unit
VCC - 3.3 3.63 (V)
Parameter Min Typ Max Unit
Environment condition
Operating Temperature: -10 deg.C ~70 deg.C
Storage Temperature: -55 deg.C ~+125deg.C
Operating Humidity: 5% ~95% (Non-condensing)
Storage Humidity: 5% ~95% (Non-condensing)
4. RF Specification
4.1
4.1 Rx Characteristics
4.14.1
Parameter Min. Typ. Max. Unit
Rx input frequency range 2.412 - 2.484 GHz
RX Characteristics Min. Typ. Max. Unit
1.Minimum Input Level Sensitivity
1) CCK, 1Mbps(PER ≤ 8%) - -95 - dBm
2) CCK, 11Mbps(PER ≤ 8%) - -86 - dBm
3) OFDM, 54Mbps(PER ≤ 10%) - -72 - dBm
4) HT20-MCS7(PER ≤ 10%) - -70 - dBm
5) HT40-MCS7(PER ≤ 10%) - -68 - dBm
2. Maximum Input Level (PER ≤ 8%)
1) 11Mbps(PER ≤ 8%) -10 - - dBm
2) 54Mbps(PER ≤ 10%) -20 - - dBm
3) HT20-MCS7(PER ≤ 10%) -20 - -
4.2
4.2 Tx Characteristics
4.24.2
Parameter Min. Typ. Max. Unit
Rx input frequency range 2.412 - 2.484 GHz
TX Characteristics Min. Typ. Max. Unit
1. Power Levels
1)Target Power@1Mbps 15.29 16.01 16.78 dBm
2)Target Power@11Mbps 15.16 15.62 16.3 dBm
3)Target Power@54Mbps 14.86 16.18 17.26 dBm
4)Target Power@HT20-MCS0 13.23 13.68 14.11 dBm
5)Target Power@HT20-MCS7 12.86 13.5 14.1 dBm
2. Frequence Error - ppm
3. Modulation Accuracy(EVM)@Target Power
1) 54Mbps - -30 -25 dB
2) HT20-MCS7 - -32 -28 dB
3) HT40-MCS7 - -33 -28 dB
5.Mechanical Specifications
PCB Assembly Dimension:
Dimension (L x W x H): L:13mm* W:13.5mm
6.FCC Caution.
1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2. Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
3. This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna. -Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected. -Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body .
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be
used with this transmitter.
The WIFI module is designed to comply with the FCC statement. FCC ID is 2AEU8SD06.
The host system using Linux, should have label indicated it contain modular’s FCC ID
2AEU8SD06
This radio module must not installed to co-locate and operating simultaneously with other
radios in host system , additional testing and equipment authorization may be required to
operating simultaneously with other radio.
Instruction for OEM:
a:Please provide below statement sontheend product user manual or on the product
b:This LMA does not have RF shielding and is tested and approved as standalone configuration,
additional evaluation may be required for any system integrated this radio module.
c:The following regulatory and safety notices must be published in documentation supplied to the
end user of the product or system incorporating the WIFI module, in compliance with local
regulations. Host system must be labeled with "Contains FCC ID: 2AEU8SD06 ", FCC ID
displayed on label.
d: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
e:This radio module must not installed to co-locate and operating simultaneously with other radios
in host system ,additional testing and equipment authorization may be required to operating
simultaneously with other radio.
f: This module has data buffer.
g: This module has internal power regulation inside the chipset. h: The modular has an integral chip antenna, its fulfil the requirements of 15.203.
i: The modular is tested in a stand-alone configuration powered by USB Port .
k: The modular complies with any applicable RF exposure requirements.
7.Host Antenna Connectors
Notes:( unless otherwise specified)
1) Finished board thickness to be 54Mils ±5%
2) Soldermask to be LPI.color.green.both sides..
3) Plating:immersion gold over electroless nickel.
Edge fingers:hard gold(50micro inches gold over 150 micro inches electroless nickel)
4) Silkscreen:Both sides,color:white
5) See drill chart for finished hole sizes
6) Hole tolerance is ±3Mils unless otherwise specified
7) See film for layer sequence
8) This is a 2 layer board
9) Bow and twist..75% max allowable
10) Fabricate per IPC-6012 class 2 (latest revision) unless otherwise specified
11) Material:fr408 or equivalent .Tg=180,Td=360
12) Teardrops:ok to add as needed to Meet .002 min.trace interconnects as per IPC-6012 class 2
Line width 20 mil, and ground plane span 6 mil, 50 ohm impedance
Top side layer 1 (1/2 oz.Cu foil)
Fr4 – Mils(No critical)
Bottom side layer 2 (1/2 oz.Cu foil)
8.Instructions on the using of the module
This module must not be incorporated into any other device or system without retesting for
compliance as a composite system.
Host manufacturers are responsible for additional testing to verify compliance as a composite
system. This includes retesting of transmitter module per part 15.31(h) and (k).
When testing the host device for compliance with Part 15 Subpart B, the host manufacturer is
required to show compliance with Part 15 Subpart B while the transmitter module(s) are installed
and operating. The modules should be transmitting and the evaluation should confirm that the
module’s intentional emissions are compliant (i.e. fundamental and out of band emissions). The
host manufacturer must verify that there are no additional unintentional emissions other than what
is permitted in Part 15 Subpart B or emissions are complaint with the transmitter(s) rule(s).
This module can only be used with a host antenna circuit trace layout design in strict compliance
with the instructions provided in this OEM manual
Loading...