ITT ICS User Manual

ITT

Goulds Pumps

G&L SERIES
MODEL ICS/ICS-F

Installation, Operation and
Maintenance Instructions

Commercial Water

Goulds Pumps is a brand of ITT Corporation.

www.goulds.com

Engineered for life

Table of Contents

SUBJECT PAGE

Safety Instructions ......................................................... 3

Description and Specifi cations ....................................... 3

Installation – General .................................................... 3

Close Coupled Units ...................................................... 3

Frame Mounted Units ................................................... 3

Piping – General ............................................................ 4

Piping – Suction ............................................................ 4

Piping – Discharge ......................................................... 4

Wiring and Grounding .................................................. 4

Motor to Pump – Shaft Alignment ................................. 5

Operation ...................................................................... 5

Maintenance.................................................................. 5

Disassembly ................................................................... 5

Reassembly .................................................................... 6

Troubleshooting Guide .................................................. 6

Sectional Assembly ....................................................... 7

Parts List and Materials of Construction ........................ 7

Engineering Data ........................................................... 8

Goulds Pumps Limited Warranty ................................. 10

Owner’s Information

Model Number:
Serial Number:
Dealer:
Date of Purchase: Date of Delivery:

2

SAFETY INSTRUCTIONS

TO AVOID SERIOUS OR FATAL PERSONAL INJURY OR
MAJOR PROPERTY DAMAGE, READ AND FOLLOW
ALL SAFETY INSTRUCTIONS IN THE MANUAL AND ON
THE PUMP.

This is a SAFETY ALERT SYMBOL. When
you see this symbol on the pump or in the
manual, look for one of the following signal
words and be alert to the potential for
personal injury or property damage.

DANGER

WARNING

CAUTION

NOTICE: INDICATES SPECIAL INSTRUCTIONS
WHICH ARE VERY IMPORTANT AND
MUST BE FOLLOWED.

THIS MANUAL IS INTENDED TO ASSIST IN THE
INSTALLATION AND OPERATION OF THIS UNIT.
THOROUGHLY REVIEW ALL INSTRUCTIONS AND
WARNINGS PRIOR TO PERFORMING ANY WORK
ON THIS PUMP.

MAINTAIN ALL SAFETY DECALS.

WARNING

Hazardous voltage
can shock, burn or
cause death.

Single phase pump motors are equipped with an
automatic thermal protector, which opens the motor’s
electrical circuit when an overload condition exists.
This can cause the pump to start unexpectedly.

Warns of hazards that WILL cause serious
personal injury, death or major property
damage.

Warns of hazards that CAN cause serious
personal injury, death or major property
damage.

Warns of hazards that CAN cause personal
injury or property damage.

Install, ground and wire accord­ing to local and National Electrical
Code Requirements.

Install an all leg disconnect switch
near the pump.

Disconnect and lockout electrical
power before installing or servicing
the pump.

Electrical supply must match motor’s
nameplate specifi cations. Incorrect
voltage can cause fi re, damage motor
and void the warranty.

DESCRIPTION and SPECIFICATIONS

The Models ICS, close coupled, and ICS-F, frame mounted,
are single stage, end suction pumps designed for ultra pure
water systems, beverage processing, chemical service and
selected OEM applications.

The pumps are of back pullout confi guration, with NPT
suction and discharge connections and have investment cast
AISI Type 316 stainless steel casings, open impellers and
seal housing. All pumps are equipped with O-ring shaft
sleeve protection and are available with a variety of optional
mechanical seals.

Close coupled units are equipped with C-face NEMA motors
with threaded shaft extensions. Frame mounted units can be
baseplate mounted and are available with spacer couplings or
may be belt driven.

Close coupled units are available with single and three phase
ODP, TEFC and explosion proof motors. Consult with your

distributor/dealer for additional information.
NOTICE: INSPECT UNIT FOR DAMAGE AND

REPORT ALL DAMAGE TO CARRIER
IMMEDIATELY.

MAXIMUM OPERATING LIMITS

Liquid Temperature:
212° F (100° C) – standard mechanical seal
250° F (120° C) – OPTIONAL mechanical seal
Operating Pressure: 175 PSI (1203 kPa)
Starts per Hour: 20, evenly distributed

Installation – General

• Locate the pump as near to the liquid source as possible.

• If pump repriming capability is required, the pump suction

MUST be below the source of the liquid level.

• Protect the pump and piping from freezing temperatures.

• Allow adequate space around the unit for service and
ventilation.

Close Coupled Units

• Units may be installed horizontally, inclined or vertically.

WARNING

Hazardous
voltage

• Unit foundation must be fl at and substantial to avoid pipe
strains when bolts are tightened. Use rubber mounts under
motor to minimize noise and vibration.

• Tighten motor holddown bolts BEFORE connecting the
suction and discharge piping.

DO NOT MOUNT MOTOR BELOW
PUMP. FLUID LEAKAGE ONTO
MOTOR CAN CAUSE A SHOCK,
BURN OR DEATH.

Frame Mounted Units

• Place the baseplate upon the foundation and disconnect the
coupling halves. DO NOT reconnect the coupling until the
alignment procedures have been completed.

• It is recommended that the baseplate be grouted to a
foundation with a solid footing, per Figure 1.

3

Finished grouting

(1/2 to 3/4")
Allowance

for leveling

Wood
frame

(

Leveling wedges or shims – left in place

Sleeve

Washer

Lug

BaseGrout hole

Grout

Top of foundation –
clean and wet down

1

/4")

Figure 1

• As depicted in Figure 1, place the baseplate on wedges,
locating two wedges at each foundation bolt location. A gap
of ¾" to 1½" (19 mm to 64 mm) is recommended between
the baseplate and the foundation for grouting. Adjust the
wedges as necessary to level the baseplate.

• Inspect baseplate for any distortion, and adjust as neces­sary. Make sure that any necessary fi nal coupling alignments
are possible within the motor movements and shim limits.
Tighten the 4 foundation bolts fi nger tight.

• Build a dam around foundation and pour grout under the
baseplate, insuring that the areas under the pump and
motor are fi lled completely.

• Allow grout to harden for 48 hours before tightening
4 foundation bolts.

Piping – General

• For maximum pump capacity, piping should not be smaller
than the pump suction and discharge.

• To minimize pipe friction losses, avoid unnecessary pipe
and fi ttings.

• All piping MUST be independently supported and MUST

NOT place any piping loads on pump.

NOTICE: DO NOT FORCE PIPING INTO PLACE AT

PUMP SUCTION AND DISCHARGE
CONNECTIONS.

Piping – Suction

• Short and direct suction piping is recommended. For
suction lifts of over 10' (3 m) and liquid temperatures over
120° F (49° C), consult pump performance curve for net
positive head required (NPSHR).

• If a pipe size larger than the pump suction is required, an
eccentric pipe reducer, with the straight side up, MUST
be installed at the pump suction.

• If the pump is installed below the liquid source, install a full
fl ow isolation valve in the suction for pump inspection and
maintenance.

NOTICE: DO NOT USE THE ISOLATION VALVE TO
THROTTLE PUMP. THIS MAY CAUSE LOSS
OF PRIME, EXCESSIVE TEMPERATURES
AND DAMAGE TO PUMP, VOIDING
WARRANTY.

4

• If pump must be installed above the liquid source, the

following MUST be provided:

• To avoid air pockets, no part of the piping should be
above the pump suction connection.

• Slope the piping upward from liquid source.

• All pipe joints MUST be airtight.

• Use a foot valve ONLY if necessary for priming or to
hold prime during intermittent duty.

• The suction strainer or suction bell MUST be at least

3 times the suction pipe diameter area.

• Insure that the size and minimum submergence over suc­tion inlet is suffi cient to prevent air from entering pump
through a suction vortex. See Figures 2 through 5.

H min.

D

Figure 2 Figure 3

3.0D
min.

1.5D
min.

H min.

D min.

D D

2

H min.

D

H

16
15
14
13
12
11
10

9
8
7
6
5
4
3
2

H = Min. Submergence in feet

1

12345678910111213141516

V = Velocity in feet per second

= GPM x 0.321

Area

GPM x 0.4085

V

2

D

Figure 4 Figure 5

Piping – Discharge

• Install a check valve, suitable to handle the fl ow and liquids,
to prevent backfl ow. After the check valve install an
appropriately sized gate valve to be used to regulate the
pump capacity, pump inspection and maintenance.

• When required, the pipe increaser should be installed be­tween the check valve and the pump discharge.

Wiring and Grounding

WARNING

Hazardous
voltage

• All wiring and grounding connections must be in accor­dance with Local and National Electrical Code require­ments.

• Use only stranded copper wire to the motor and ground.
Wire size MUST limit the maximum voltage drop to 10%
of the motor nameplate voltage, at the motor terminals.
Excessive voltage drop may affect performance and will
void the motor warranty.

• Single phase motors supplied by Goulds, have built in ther­mal overloads. Other motors not so equipped MUST
use a properly sized contactor and overload. Fuses are
permissible.

• Three phase motors require all leg protection with properly
sized magnetic starters and thermal overloads.

DISCONNECT AND LOCKOUT
THE ELECTRICAL POWER BEFORE
ATTEMPTING ANY MAINTENANCE.
FAILURE TO DO SO CAN CAUSE A
SHOCK, BURN OR DEATH.

NOTICE: UNIT ROTATION IS CLOCKWISE WHEN

VIEWED FROM MOTOR END. INCORRECT
ROTATION MAY CAUSE DAMAGE TO THE
PUMP AND VOIDS WARRANTY.

• Three Phase Motors ONLY:

To check the pump rotation, observe pump while switch­ing the electrical power ON then OFF quickly. If incorrect,
have a qualifi ed electrician interchange two of the three
motor power wires.

Motor to Pump – Shaft Alignment

• After completion of the frame mounted unit baseplate

installation, the motor and pump shaft alignment MUST
be checked, see Figure 6, and the coupling spacer must
be reinstalled.

• Before checking shaft alignment, insure that the foun­dation, pump and motor holddown bolts are properly
tightened.

• If realignment is required, ALWAYS make the required
adjustments to the motor, shimming as necessary.

WARNING

DO NOT OPERATE PUMP AT OR
NEAR ZERO FLOW. TO DO SO CAN
CAUSE EXTREME HEAT, DAMAGE TO
THE PUMP, PERSONAL INJURY OR
PROPERTY DAMAGE.

Extreme heat can
cause personal injury
or property damage.

• After stabilizing the system at normal operating conditions,
check the piping and coupling for correct alignments. If
necessary, adjust pipe supports and realign the shafts
following the procedures provided.

Maintenance

• Close coupled pump motors and frame mounted pump
frames have permanently lubricated bearings. Additional
lubrication is not necessary or possible.

• Follow the coupling and motor manufacturer’s
recommendations regarding maintenance.

Parallel

Angular

Figure 6

• To check for PARALLEL misalignment, place a dial

indicator on one coupling hub, rotate the hub 360° while
observing the indicator readings from the outside diameter
of the other hub. Parallel alignment requires a Total
Indicator Reading (TIR) of 0.005" (0.13 mm), or less.

• To check for ANGULAR misalignment, place a dial indica-

tor on one coupling hub, rotate the hub 360° while observ­ing the indicator readings from the face of the other hub.
Angular alignment requires 0.005" (0.13 mm) TIR, or less.

• Correct alignment is achieved when parallel and angular
TIR requirements are satisfi ed and motor holddown bolts
are tight.

NOTICE: RECHECK SHAFT ALIGNMENT AFTER
MAKING ANY ADJUSTMENTS.

Operation

WARNING

Hazardous machinery
can cause personal
injury or death.

NOTICE: PUMP MUST BE COMPLETELY PRIMED
BEFORE OPERATION.

DO NOT OPERATE UNIT WITHOUT
SAFETY GUARD IN PLACE. TO DO
SO CAN CAUSE SEVERE PERSONAL
INJURY OR DEATH.

Disassembly

WARNING

Hazardous
machinery

WARNING

Hazardous fluids can
cause personal injury
or property damage.

• Drain and fl ush system, as required.

• For close coupled or frame mounted units:

• Remove the motor or bearing frame holddown bolts

• Remove the coupling guard and coupling spacer

• Remove the 4 casing screws (370), then utilizing the slots
provided about the casing (100), pry the back pull-out as­sembly from casing. Carefully remove the casing shims.

NOTICE: IMPELLER COMPRESSES THE MECHANICAL
SEAL SPRING – BE PREPARED FOR THE
IMPELLER TO SPRING FROM THE SHAFT
WHEN UNSCREWED.

• To remove the impeller it is necessary to heat the center
hub area with a hand propane torch for approximately 30
seconds. Unscrew the impeller (101) from the shaft, turn the
impeller COUNTERCLOCKWISE while holding the shaft.
Motors have a screwdriver slot or hex provided under the
motor end cap. Examine the impeller for wear or damage and
replace as necessary. Discard the shaft sleeve O-ring (412A).

NOTICE: EXERCISE CARE HANDLING HOT
IMPELLER.

• To remove the mechanical seal, remove the 4 seal housing
screws (370H) and slide the seal housing assembly off the
shaft. Discard the rotary half of the seal and the seal hous­ing O-ring (513). With an appropriately sized screwdriver
handle, push the stationary half of the seal from the seal
housing and discard it.

DISCONNECT AND LOCKOUT
ELECTRICAL POWER BEFORE
ATTEMPTING ANY MAINTENANCE.
FAILURE TO DO SO CAN CAUSE A
SHOCK, BURN OR DEATH.

CASING MAY CONTAIN HAZARDOUS
FLUIDS THAT CAN CAUSE SERIOUS
PERSONAL INJURY OR PROPERTY
DAMAGE.

5

• To remove the shaft sleeve (126) it is necessary to evenly
heat the outside of the sleeve, with a hand propane torch,
while prying between the shaft shoulder and the sleeve.

NOTICE: EXERCISE CARE HANDLING THE HOT
SHAFT SLEEVE.

• Removal of the 4 motor adapter screws (371) and motor
adapter (108) from the motor completes the close coupled
unit disassembly.

• Disassembly of the bearing frame assembly is accomplished
by removing the 4 frame adapter screws (371) and remov­ing the frame adapter (108) from the bearing frame (228).

• Remove the 4 bearing cover (370C) screws, being careful
not to damage the lip seal (139). Inspect lip seal for damage
and replace as required.

• Remove the shaft assembly from the bearing frame, by pull­ing the motor end of shaft out of the housing.

• Being careful not to damage the shaft, remove the snap ring
(361) and outer bearings (112) from the shaft. If required
remove the inner bearing (168). Inspect the bearings for
wear or damage and replace as necessary.

• Inspect the inner lip seal (138) and replace as required.

• Disassembly is complete.

• Shim pack (330) permits renewal of impeller clearance to
compensate for impeller or casing wear. The shim thick­nesses, in the shim pack, range from 0.003" to 0.025"
(0.08 mm to 0.64 mm). The factory shim pack thickness
is approximately 0.060" (1.52 mm). To set the suggested
nominal impeller clearance of 0.020" (0.51 mm) proceed as
follows:

• Establish a shim pack thickness that allows for the impel-

ler to just touch the inside of the casing surface, when
pump is assembled.

• Add an additional 0.020" (0.51 mm) thickness of shims.

• When the proper impeller clearance has been achieved,
install and tighten the 4 casing screws.

• Install the 4 bearing frame holddown bolts for the frame
mounted units or the 4 motor holddown bolts for the close
coupled units.

• On frame mounted units, check the coupling alignment as
specifi ed in the “MOTOR TO PUMP – SHAFT
ALIGNMENT” section of this manual.

• Inspect unit rotation for binding and correct as required.

• Reinstall the safety guard.

• Reassembly is complete.

Reassembly

• Reassemble the bearing frame assembly in reverse order
of disassembly. Use appropriate tools for bearing installa­tion and press ONLY on inner bearing race. Press bearings
squarely and completely onto the shaft.

• If the shaft sleeve was replaced, it is required that the new
sleeve be bonded to the shaft using LoctiteTM #243 or
equivalent. Following the manufacturer’s instructions in the
preparation of the sleeve and shaft, apply bonding agent to
the surfaces then slide the sleeve over the shaft. Remove all
excess bonding agent.

• Install the shaft assembly into bearing frame. DO NOT
damage the inner lip seal.

• Insert and tighten the 4 bearing cover screws.

• Install the bearing adapter, nameplate towards the TOP,
using the 4 screws.

• Inspect and remove any debris from the seal housing sta­tionary seat bore. Lubricate the outside diameter of the new
stationary seat with a good quality O-ring lubricant and
press seat squarely and completely into the seal housing.
With a clean, lint free cloth remove any debris or lubricant
from the seat face. DO NOT scratch the face.

• Install a new seal housing O-ring on housing, then care­fully slide seal housing over shaft and attach housing to the
motor adapter with the 4 screws. DO NOT damage the
mechanical seal stationary seat.

• Install the new shaft sleeve O-ring.

• Slide the new mechanical seal rotary assembly over shaft
sleeve. Apply Loctite™ 7649 and allow to dry. Apply
Loctite™ #243 to the motor shaft thread and then screw
on the impeller by turning impeller CLOCKWISE. Torque
the impeller to 12 ft lbs (1.7 kg/m).

Troubleshooting Guide

WARNING

Hazardous
voltage

MOTOR NOT RUNNING
See Probable Cause – 1 through 5

LITTLE OR NO LIQUID DELIVERED BY PUMP
See Probable Cause – 6 through 13

POWER CONSUMPTION TOO HIGH
See Probable Cause – 3, 13, 14, 15, 18

EXCESSIVE NOISE and VIBRATION
See Probable Cause – 3, 6, 7, 8, 10, 12, 14, 16, 17, 18

1. Motor thermal protector tripped

2. Open circuit breaker or blown fuse

3. Impeller binding

4. Motor improperly wired

5. Defective motor

6. Pump is not primed, air or gases in pumpage

7. Discharge, suction plugged or valve closed

8. Incorrect rotation (3 phase only)

9. Low voltage or phase loss

10. Impeller worn or plugged

11. System head too high

12. NPSHA too low – Suction lift or suction losses excessive

13. Incorrect impeller diameter

14. Discharge head too low – excessive fl ow rate

15. Fluid viscosity, specifi c gravity too high

16. Worn bearing

17. Pump, motor or piping loose

18. Pump and motor shafts misaligned

DISCONNECT AND LOCKOUT
ELECTRICAL POWER BEFORE
ATTEMPTING ANY MAINTENANCE.
FAILURE TO DO SO CAN CAUSE A
SHOCK, BURN OR DEATH.

SYMPTOM

PROBABLE CAUSE

6

ICS & ICS-F Sectional Assemblies

100

101

412A

408
Optional,
408
Opcional

184 513 370 383 371 126

108

100

101

126

412A

408
Optional,
408
Opcional

184 513 370 383 371 138 168 122 112 370C

108

Parts List and Materials of Construction

LIQUID END COMPONENTS
Item No. Number/Pump Part Name Material

1 Casing – 1¼ x 1½ - 5 ASTM A744 Grade CF-8M
101 1 Impeller ASTM A744 Grade CF-8M
126 1 Shaft Sleeve ASTM A276 Type 316 SS
184 1 Seal Housing ASTM A744 Grade CF-8M
330* 1 Shim Pack Mylar
370 4 Hex Cap Screws – adapter to casing ASTM A276 Type 304 SS
370H* 4 Hex Cap Screws – adapter to seal housing ASTM A276 Type 304 SS
Mechanical Seal (standard) Carbon/Sil Car/Viton

412A 1 O-ring – Shaft Sleeve Viton
513 1 O-ring – Seal Housing Viton
* Not illustrated

1 Casing – 1 x 1¼ - 5 ASTM A744 Grade CF-8M

100

383 1

Mechanical Seal (optional) Carbon/Sil Car/EPR

361

109

139

POWER END COMPONENTS
Item No. Number/Pump Part Name Material

108 1 Motor and Bearing Frame Adapter ASTM A48 Cast Iron
109 1 Bearing Cover ASTM A48 Cast Iron
112 1 Ball Bearing – outboard ASTM A108 Steel
122 1 Pump Shaft ASTM A276 Type 303 SS
168 1 Ball Bearing – inboard ASTM A108 Steel
361 1 Snap Ring – outboard bearing ASTM A108 Steel
228 1 Bearing Frame ASTM A48 Cast Iron
138 1 Lip Seal – inner BUNA-N and ASTM A108 Steel
139 1 Lip Seal – outer BUNA-N and ASTM A108 Steel

bearing cover to bearing frame

adapter to motor/bearing frame

370C 4

371 4

Hex Cap Screws –

Hex Cap Screws –

ASTM A108 Steel

ASTM A276 Type 304 SS

7

ICS – Engineering Data

½ HP – 2 HP

4.88

MAX.

58317 CF–8M

6.75

R

3.50

X

4.12

2.942.94

DISCHARGE

Dimensions and Weights – Determined by Pump

Pump Suction NPT Discharge NPT L R W X *Wt. Max.

1 x 1¼-5 1¼ 1 3.75 .94 3.01 4.62 17

1¼ x 1½-5 1½ 1¼ 3.62 1.06 2.88 4.56 17

Available Motor Weights and Dimensions

Motor Weights
HP Single Phase Three Phase
ODP TEFC EXP ODP TEFC EXP

½

16 21 47 19 18 27 915⁄
¾ 19 24 41 21 21 30 10¼
1 22 26 49 23 21 30 11
1½ 28 35 56 27 27 37 115⁄
2 33 39 60 32 33 44 121⁄

C Max.
Length

16

16

16

C

MAX.

SINGLE PHASE ONL Y

2.50L

.41 DIA HOLES
4 PLACES,

2.66

6.31

MAX.

SUCTION

2.88

3.38

1

⁄4 NPT (OPTIONAL)

1.59

W

2.50

6.50

NOTES:

1. Pumps will be shipped with top vertical discharge as standard, for other
orientations, remove casing bolts,rotate to desired position, and tighten 3⁄8" bolts
to 24 lbs.-ft.

2. Dimensions in inches, weight in pounds.

3. Not to be used for construction purposes unless certifi ed.

4. Motor dimensions may vary with motor manufacturers.

* Weight is liquid end only. For complete pump, add weight of applicable
motor.

3 HP Only

4.88

MAX.

58317 CF–8M

6.50

3.50

2.442.44

5.28 3HP 1 PHASE ONLY

R

X

3.50

.19

DISCHARGE

Dimensions and Weights – Determined by Pump

Pump Suction NPT Discharge NPT L R W X *Wt. Max.

1 x 1¼-5 1¼ 1 7.35 .94 3.01 4.62 17

1¼ x 1½-5 1½ 1¼ 7.22 1.06 2.88 4.56 17

SUCTION

3.38

1.59

2.88

1

⁄4 NPT (OPTIONAL)

W

C

MAX.

SINGLE PHASE ONL Y

1.5 1.5L

5.88

MAX.

SLOT .34 WIDE

C

C

X .88 TO

L

5.31

L

7.10

MAX.

Available Motor Dimensions and Weights

Motor Weights
HP Single Phase Three Phase C Max. Length
ODP TEFC ODP TEFC X-Proof

3 40 45 42 37 — 13.34
Dimensions in inches, weight in pounds.

8

ICS-F – Engineering Data

Pump Dimensions and Weights

5.88

MAX.

58317 CF–8M

HEHE

HA

58317 CF–8M

3.50

HG

SUCTION

HL

W

1.59

2.88

1

⁄4 NPT (OPTIONAL)

CP

DISCHARGE

R

3.50

X

4.50

2.002.00

5.25

1.59

DISCHARGE

X

SUCTION

HD

3.38

CP

W

2.00

.8750

DIA.

.8745

KEYWAY .19 x .12,

.50

L

3.25

4.94

4 HOLES .38 DIA.

3.50
SPACER COUPLING

COUPLING GUARD,

HF HP

HB

SINGLE PHASE ONLY

C

MAX.

3.12

MAX.

7.88

MAX.

4 HOLES
.62 DIA.

Dimensions and Weights – Determined by Pump

HL (Motor Frame)

Pump Suction NPT Discharge NPT CP L R W X Wt. Max.

56 140 180

1 x 1¼-5 1¼ 1 12.16 5.73 .94 3.01 4.62 38 5.73 3.85
1¼ x 1½-5 1½ 1¼ 12.03 5.60 1.06 2.88 4.56 38 5.60 3.72

NOTES:

1. Pumps will be shipped with top vertical discharge as standard, for other
orientations, remove casing bolts, rotate to desired position, and tighten

3

⁄8" bolts to 24 lbs.-ft.

2. Dimensions in inches, weight in pounds.

3. Not to be used for construction purposes unless certifi ed.

4. Motor dimensions may vary with motor manufacturers.

Available Motor and Bedplate Dimensions and Weights

Horsepower – 3500 RPM

Motor

HA HB HD HE HF HG HP Wt. Max. Shims Single Phase Three Phase C Max.

Frame

ODP TEFC ODP TEFC

56

½

- 1½ ½ - 1½ ½ - 1 ½ - 1 45 13
143T 8 6.87 3.12 22.38 2.38 1.00 30 1.00 — — 1½ 1½ 45 13.38
145T 26 2 2 2-3 2 52 14.25
182T
184T 5 5 — 5 112 18.12

10 7.25 3.75 24 2.75 .88 43 —

3 3 5 3 63 16.62

Dimensions in inches, weight in pounds.

Wt.

Max.

9

ITT

GOULDS PUMPS LIMITED WARRANTY

This warranty applies to all water systems pumps manufactured by Goulds Pumps.
Any part or parts found to be defective within the warranty period shall be replaced at no charge to the dealer during the warranty period. The

warranty period shall exist for a period of twelve (12) months from date of installation or eighteen (18) months from date of manufacture, which­ever period is shorter.

A dealer who believes that a warranty claim exists must contact the authorized Goulds Pumps distributor from whom the pump was purchased
and furnish complete details regarding the claim. The distributor is authorized to adjust any warranty claims utilizing the Goulds Pumps Customer
Service Department.

The warranty excludes:

(a) Labor, transportation and related costs incurred by the dealer;
(b) Reinstallation costs of repaired equipment;
(c) Reinstallation costs of replacement equipment;
(d) Consequential damages of any kind; and,
(e) Reimbursement for loss caused by interruption of service.

For purposes of this warranty, the following terms have these defi nitions:

(1) “Distributor” means any individual, partnership, corporation, association, or other legal relationship that stands between Goulds Pumps and
the dealer in purchases, consignments or contracts for sale of the subject pumps.

(2) “Dealer” means any individual, partnership, corporation, association, or other legal relationship which engages in the business of selling or
leasing pumps to customers.

(3) “Customer” means any entity who buys or leases the subject pumps from a dealer. The “customer” may mean an individual, partnership,
corporation, limited liability company, association or other legal entity which may engage in any type of business.

THIS WARRANTY EXTENDS TO THE DEALER ONLY.

Commercial Water

10

Goulds Pumps, G&L and the ITT Engineered Blocks Symbol are
registered trademarks and tradenames of ITT Corporaton.

Loctite is a registered trademark of Loctite Corporation.
Tefl on is a registered trademark of Dupont.

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

IM011R04 March, 2007

© 2007 ITT Corporation

Engineered for life