Itron DCU5310 Users Manual
About the Mobile Collection 2.x System
Flash Card Reader
Route data can be transferred to and from the Mobile Collector using a removable flash card
(two CompactFlash® cards are supplied). The Windows operating system on the GoBook
recognizes the flash card as a removable drive, allowing standard file access.
Periodic data backups to the flash card can be configured in the Mobile Administration
application; see the
Help
for more information.
Mobile Collection Administration Guide (TDC-0381-001) or Online
See the Mobile Collection User's Guide (TDC-0380-xxx) or Online Help for more
information on using the flash card in day-to-day activities.
Compact Flash Cards
The Mobile Collection system includes two SanDisk CompactFlash cards. If you require
more cards, you may purchase them through Itron or through electronics stores or
distributors.
Use of unapproved cards can result in loss of data.
If you purchase additional cards from a distributor or electronics retailer, Itron recommends
the following:
• 64M SanDisk Industrial Grade, Extended Temperature range
• 64M Hitachi Renesas, Industrial Grade, Wide Temperature, or Extended Temperature
range
LEDs
Three LEDs signal system power, system operation, and flash card status. Errors relating to
the transmitter and receivers display on the GoBook within the Mobile Interface.
The table below describes the LED status indicators.
LED Color Description
Power/Error 1
Red Voltage error condition
Flashing Green Vehicle accessories power on, ignition off
Green Vehicle ignition on
None System is shutting down or completely off
Operate/Error 2 Red Temperature error condition
Hardware Installation Guide 29
Chapter 2 Using the Mobile Collection 2.x System
LED Color Description
Green Operating normally
None System is shutting down or completely off
Flash Card
Red
Data transferring to/from the flash card
reader
None System is shutting down or completely off
Locking Mechanism
The locking mechanism attaches the GoBook to the Mobile Collector. Locking the GoBook
to the Mobile Collector reduces the likelihood of the GoBook separating from the Mobile
Collector in the event of a collision.
The GoBook MAX has a keyed locking mechanism; the GoBook III has a keyless locking
mechanism.
WARNING! Do not set down the Mobile Collector on its front face while
carrying it by the handle or at any time. Doing so may damage the flash card
reader or the flash card, or may break off the key if it was left in the mounting
lock.
Rear Connectors
The rear of the Mobile Collector 2.x radio contains the power and communications
connectors.
30 Hardware Installation Guide
About the Mobile Collection 2.x System
p
ID Connector Description
1 RF antenna
Connects to the roof-mounted antenna. See the
Mobile Collection Vehicle Preparation Guide.
Itron provides a magnetic mount opti on for the
RF antenna. This magnetic mount is intended as
a temporary solution and it is for emergency use
only. Long-term use of a magnetic mount
antenna could adversely affect system
erformance and is not a supported configuration
of this product.
2 GPS antenna
Connects to the externally-mounted GPS
antenna. This gold-plated connector is used with
the optional Mapping feature of the Mobile
Interface software.
3 USB
Connects the GoBook III computer to the radio
for data transfer.
Also for use with a GoBook computer not
mounted directly to the Mobile Collector radio.
Vehicle Dock / Pedestal Option on page 33
See
for more information.
Mobile Collector radios for use with the GoBook
MAX have a USB data connection built into the
radio lid.
4 GPS receiver
Connects to an external GPS receiver box when
using a version 2.0 radio.
Version 2.5 radios have a GPS receiver built into
the Mobile Collector, so this connector is not
used with a 2.5 radio.
5 GoBook III power Provides power to the GoBook III laptop.
Mobile Collector radios for use with the GoBook
MAX have a power connection built into the
radio lid.
6 Power in
Receives power from the vehicle and distributes
it to the radio and GoBook.
In addition to wiring the power cable directly to
the vehicle, a cigarette lighter power cable is
available for emergency use only. Using this
cable will disable the power management
functions of your Mobile Collector and could
adversely affect system performance.
ALWAYS disconnect this cable from the power
source when not in use. Failure to do so could
result in a dead vehicle battery.
7 Fuse holder and fuse
Provides over-current protection for the radio.
Holder accepts standard automotive 12V (15
amp) ATO fuse (included) to protect internal
circuitry from power surges by the vehicle.
Hardware Installation Guide 31
Chapter 2 Using the Mobile Collection 2.x System
Mobile Collector Sled
The Mobile Collector sled is a mounting bracket designed to secure the Mobile Collector
radio in the vehicle and support it and the GoBook in an upright position on the passenger
seat.
GoBook Mounting Systems
There are two mounting options for the GoBook:
• Direct Mount Option The GoBook mounts directly on the Mobile Collector.
• Vehicle Dock / Pedestal Option The GoBook mounts remotely on a free-standing
pedestal, using the Itronix vehicle cradle.
The Itronix documentation refers to the laptop receptacle as a cradle; Itron uses
the term
throughout this manual; however,
WARNING! Improperly installed or secured components may
result in injury or death in the event of a collision. Install and secure
the system components in accordance with this document, the
Mobile Collection Vehicle Preparation Guide, the Mobile Collection
Sled and Pretensioner Installation Guide, manufacturer installation
instructions, and applicable safety standards.
Direct Mounting Options
dock to identify this piece of equipment. The term dock is used repeatedly
dock and cradle are interchangeable.
The GoBook communicates with the Mobile Collector and receives power from it through
the mounting connector, providing fast, easy docking and removal, without additional
cables.
The GoBook MAX mounts onto the Mobile Collector radio within the mounting guides so
that the mounting connector and the external modem connector insert into mating
connectors on the underside of the GoBook. A key inserted into the locking mechanism
turns clockwise to lock the GoBook in place.
32 Hardware Installation Guide
Installing the Mobile Collection 2.x System
The GoBook III mounts onto the Mobile Collector radio within the mounting guides, but
communicates through a USB cable and is powered from a cable connected to the Mobile
Collector.
Vehicle Dock / Pedestal Option
Optionally, you may mount the GoBook on a vehicle cradle that is attached to a pedestal.
This option allows you to position the Mobile Collector in the vehicle so that it is closer to
the driver, while placing the Mobile Collector and its base elsewhere in the vehicle. A key
inserted into the locking mechanism turns clockwise to lock the GoBook MAX in place; a
similar mechanism will be available for use with the GoBook III.
Installing the Mobile Collection 2.x System
This section shows you how to properly install a Mobile Collection 2.x system, with either a
GoBook III or a GoBook MAX.
Attach the Mobile Collector 2.x to the Sled
A plate installed on the underside of the Mobile Collector contains holes and slots that mate
with the pins on top of the sled. Attach the Mobile Collector to the sled by lowering it onto
the pins and rotating it so that the pins slide into the slots, locking the Mobile Collector in
place.
To attach the Mobile Collector to the Sled
1. Hold the Mobile Collector over the base and orient it so that the right rear corner faces
the passenger door.
2. Lower the Mobile Collector onto the sled and gently move it around until the center
pin on the base snaps into the center hole on the underside of the Mobile Collector.
Hardware Installation Guide 33
Chapter 2 Using the Mobile Collection 2.x System
3. While gently applying downward pressure, rotate the collector back and forth slightly
until the three pins on the base fit into the three matching holes on the underside of the
Mobile Collector.
4. Grip two corners of the Mobile Collector that are opposite each other diagonally and
rotate it counter-clockwise until you hear the locking pin snap into the underside of
the Mobile Collector.
When finished, the rear of the Mobile Collector should be flush with the side of the
base and its rear connectors should face the passenger door.
Connect the Antennas and Power Cables
The RF antenna, GPS antenna, and Mobile Collector power cable should be pre-installed in
the vehicle and routed to where the Mobile Collector will be installed.
The GPS system for version 2.x Mobile Collectors is an optional component that
is part of the Mapping system. If your installation does not include Mapping,
simply attach the RF antenna and the power cable in the procedure below; ignore
the steps related to the GPS antenna.
This section shows you how to connect the antennas and the power cable to the rear of the
Mobile Collector radio.
34 Hardware Installation Guide
Installing the Mobile Collection 2.x System
To connect the antennas and power cables
1. Plug the power cable (1) into the power connector on the Mobile Collector.
2. Attach the pre-wired RF antenna cable (2) and turn the knurled part of the antenna
cable clockwise until the cable is firmly attached.
If the power cable does not reach the Mobile Collector, use the optional
extension cable to extend the length (extension cables may be purchased
from Itron). Plug the power cable into one end of the extension cable and
plug the other end of the extension cable in to the Mobile Collector. Be sure
both ends snap into their respective connectors.
3. Attach the GPS cable to the connector. Both the end of the cable and the connector are
gold-plated for easy identification.
Attach the GoBook to the Mobile Collector 2.x
This section shows you how to connect both the GoBook MAX and GoBook III to the
Mobile Collector radio. The GoBook may be either attached directly to the Mobile
Collector radio or attached to a vehicle cradle mounted on a pedestal by the driver (for more
information, see
To attach the GoBook to the Mobile Collector, follow the steps in one of the following
sections:
GoBook Mounting Systems on page 32).
GoBook MAX Procedures GoBook III Procedures
Attach the GoBook MAX to the Mobile
Collector
Attach the GoBook MAX to the Vehicle
Dock
Hardware Installation Guide 35
on page 36
on page 38
Attach the GoBook III to the Mobile
Collector
Attach the GoBook III to the Vehicle
Dock
on page 37
on page 39
Chapter 2 Using the Mobile Collection 2.x System
Attach the GoBook MAX to the Mobile Collector
Follow these steps to mount the GoBook MAX onto the Mobile Collector.
Before attempting to mount the GoBook onto the Mobile Collector, be sure to
unlock the locking mechanism.
To attach the GoBook MAX to the Mobile Collector
1. From the driver’s side of the vehicle, align the GoBook MAX with the four mounting
guides on top of the Mobile Collector.
2. Angle the top of the GoBook MAX towards the passenger door, as shown below, and
lower it so that the two rear connectors (1) on the Mobile Collector top fit into the
mating holes on the GoBook MAX underside.
3. Lower the GoBook MAX onto the Mobile Collector within the mounting guides (2)
until the underside of the GoBook MAX is flush with the top of the Mobile Collector.
If necessary, gently move the GoBook MAX slightly from side to side to ensure the
connectors on top of the Mobile Collector mate with those on the underside of the
GoBook MAX.
36 Hardware Installation Guide
Installing the Mobile Collection 2.x System
4. Insert the key into the mounting lock and press the locking mechanism so it engages
the GoBook MAX.
5. Turn the key clockwise to lock the GoBook MAX in place.
6. Remove the key from the lock so that it is not stolen or accidently broken.
7. Lift the GoBook MAX screen up and gently push it back so that it rests on the Mobile
Collector screen rest.
Attach the GoBook III to the Mobile Collector
Follow these steps to mount the GoBook III onto the Mobile Collector.
To attach the GoBook III to the Mobile Collector
1. From the driver’s side of the vehicle, align the GoBook III with the two mounting
guides (1) on top of the Mobile Collector.
2. Angle the GoBook III towards the passenger door, as shown below, and slide it under
the mounting guides (1) toward the back of the Mobile Collector.
3. Lower the GoBook III onto the Mobile Collector within the mounting guides until the
underside of the GoBook III is flush with the top of the Mobile Collector.
Hardware Installation Guide 37
Chapter 2 Using the Mobile Collection 2.x System
If necessary, gently move the GoBook III slightly from side to side to ensure the
connectors on top of the Mobile Collector mate with those on the underside of the
GoBook III.
4. With one hand, pull on the locking mechanism to release it. With the other hand,
gently push down on the top of the GoBook III, as shown below.
5. Release the locking mechanism to lock the GoBook III in place.
6. Attach the necessary USB and power cables from the Mobile Collector to the GoBook
III.
7. Secure the USB cable in place by tightening the metal cable clip.
8. Lift the GoBook III screen up and gently push it back so that it rests on the Mobile
Collector screen rest.
Attach the GoBook MAX to the Vehicle Dock
As part of an optional remote installation, you may attach the GoBook MAX to a vehicle
dock on a pedestal near the driver. The vehicle dock should be pre-installed. Refer to the
Itronix Vehicle Cradle Installation Guide for detailed instructions.
The Itronix documentation refers to the laptop receptacle as a cradle; Itron uses
the term
throughout this manual; however,
To attach the GoBook MAX to the vehicle dock
1. Angle the top of the GoBook MAX and center on the vehicle dock mounting guides,
then lower it so that the two rear locking mechanisms on the vehicle dock top fit into
the mating holes on the GoBook MAX underside.
2. Lower the GoBook MAX onto the vehicle dock within the mounting guides until the
underside of the GoBook MAX is flush with the top of the vehicle dock.
dock to identify this piece of equipment. The term dock is used repeatedly
dock and cradle are interchangeable.
3. Insert the key into the mounting lock.
4. Press the locking mechanism so it engages the GoBook MAX.
38 Hardware Installation Guide
Loading...