ITI Concord, Concord RF 2.0 Installation Instructions Manual

Page 1

Installation Instructions



This document describes the installation, programming, testing, and troubleshooting procedures for installing Concord 2.0 security systems.

About This Manual ...............................................5

Special Installation Requirements .................5

UL-Listed Installations .............................5

UL-Canada Listed Installations ................6

California State Fire Marshall

Listed Installations ....................................6

Planning the Installation ........................................6

Standard Panel ...............................................6

SuperBus 2000 Touchpads .............................6

SuperBus 2000 RF Receivers ........................6

Power Line Carrier Card ................................7

Phone Supervision Card .................................7

Supervised Wireless Siren .............................7

SuperBus 2000 Phone Interface/Voice

Module ........................................................... 7

SnapCards ...................................................... 7

SuperBus 2000 8Z Input

Module (HIM) ................................................7

SuperBus 2000 4-Relay Output

Module (HOM) ..............................................7

Interrogator 200 Audio

Verification Module .......................................7

Installing the System .............................................7

Determine the Panel Location ........................8

Total System Power and Wire Length

Guidelines ...................................................... 8

Mounting the Panel ........................................9

Identify Panel Components ..........................10

Installing Antennas ......................................10

Connecting the Panel to Earth Ground ........ 10

Installing the Optional Power Line

Carrier Card ............................................. ....11

Installing the Optional Phone

Supervision Card .......................................... 11

Installing Optional SnapCards ..................... 11

Connecting Detection Devices to Panel

Zone Inputs ..................................................12

Connecting Intrusion Detection Devices 12

Connecting 2-Wire Smoke Detectors .....12

Connecting 4-Wire Smoke Detectors .....13

Connecting Speakers ....................................13

15-Watt Speaker ......................................14

Hardwire Interior Speaker ......................14

Connecting Piezo Sirens ..............................14

Exterior Sirens ........................................15

Interior Sirens .........................................15

Installing Supervised

Wireless Sirens .............................................15

Connecting an Interrogator 200

Audio Verification Module ..........................16

 

Document No. 466-1512-01 August 2, 2000 Preliminary

Connecting Alphanumeric and

Fixed Display T ouch pads .............................16

Installing SuperBus 2000 Modules ..............17

SuperBus 2000 RF Receiver

(60-764-01-95R-16Z/32Z/MAX) ...........17

SuperBus 2000 Phone

Interface/Voice Module............................18

Energy Saver Module...............................19

SuperBus 2000 8Z Input Module.............19

4-Relay Output Module ..........................20

Setting Device Address on SuperBus

2000 Devices ................................................20

Installing an RJ-31X Phone Jack .................20

Connecting the Phone Line to the

Panel with a DB-8 Cord ...............................21

Connecting the AC Power Transformer .......21

Powering Up the Panel .................................22

Programming the Panel .......................................22

Entering Program Mode ...............................22

Touchpad Button Programming Functions .. 23 Moving Through Program Mode

Tiers and Menus ...........................................23

Programming Tier 1 Menu Items .................24

Programming Tier 2 Menu Items .................24

Using Shortcut Numbers .........................25

Security Menu .........................................25

Phones Menu ...........................................27

Phone Options Menu ............................... 30

Timers Menu ...........................................34

Light Control Menu ................................36

Touchpad Options Menu .........................36

Reporting Menu ......................................37

Siren Options Menu ................................41

Sensors Menu ..........................................42

Audio Verification Menu ........................44

Accessory Modules Menu .......................45

Onboard Options Menu ........................... 48

Exiting Programming Mode .........................50

Entering User Programming Mode ..............50

Time and Date Menu ...............................50

User Codes Menu ....................................50

Options Menu ..........................................52

Set Up Schedules Menu ..........................53

Attach Schedules to Events Menu ..........53

Energy Saver Menu .................................55

Attach Lights to Sensors Menu ...............55

System Version Menu .............................55

Downloader Programming ...........................56

ToolBox Downloader Programming .......56

Page 2

Installation Instructions

Testing the System ...............................................56

Basic System Commands .............................56

Testing Zones/Sensors ..................................56

If a Wireless Sensor Does Not Test .........57

Testing Phone Communication .....................57

Testing Central Station/Pager

Communication ............................................57

Testing Outputs and Sirens ...........................58

Testing Light Control ...................................58

Testing the Energy Saver Module (ESM) ....58

Changing Fixed D i splay LCD Touchpad Chime and Trouble Beep Tones ...59 Testing Audio Verification Module (AVM)

Communication ............................................59

Troubleshooting ...................................................61

Appendix A: System Planning Worksheets .........69

Appendix B: Reference Tables ............................74

Appendix C: Reference Tables ............................77

Programming Mode Menus and Settings ............81

System Wiring Notes ...........................................87

Index ....................................................................89

DRAFT 8/17/00

Page 3

Notices

FCC Part 15 Information to the User

Changes or modifications not expressly approved by Interactive Technologies, Inc. can void the user’s authority to operate the equipment.

FCC Part 15 Class A (Commercial)

This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which ca se users will be required to correct the interference at their own expense.

FCC Part 15 Class B (Residental)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Install a quality radio or television outdoor antenna if the indoor antenna is not adequate.

• Reorient or relocate the panel.

• Move the panel away from the affected equipment.

• Move the panel away from any wire runs to the affected equipment.

• Connect the affected equipment and the panel to separate outlets, on different branch circuits.

• Consult the dealer or an experienced radio/TV technician for help.

• Send for the FCC booklet How to Identify and Resolve Radio-TV Interference Problems, available from the U.S. Government Printing Office, Washington, D.C.

20402. Stock Number: 004-000-00345-4.

FCC Part 68

This equipment complies with Part 68 of the FCC Rules. Located on this equipment is a label that contains, among other information, the FCC registration number and the ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.

The REN is used to determine the maximum number of devices that may be connected to your telephone line. In most areas, the sum of all device RENs should not exceed five (5.0).

If this equipment causes harm to the telephone network, the telephone company may temporarily disconnect your service. If possible, you will be notified in advance. When advance notice is not practical, you will be notified as soon as possible. You will also be advised of your right to file a complaint with the FCC.

Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of your equipment. You will be given advanced notice in order to maintain uninterrupted service.

If you experience trouble with this equipment, please contact

Interactive Technologies, Inc. 2266 Second Street North North Saint Paul, MN 55109 1-800-777-1415

This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs.

Declaration of Conformity (DoC)

Interactive Technologies, Inc. declares that the ITI model no. 60-792-95R is in conformity with Part 15 of the FCC Rules. Operation of this product is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Page 4

Canada Notice

The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single-line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.

Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.

For your protection, make sure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together.

Caution

Do not attempt to make connections yourself. Contact the appropriate electrician or electric inspections authority.

The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop that is used by the device to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the LNs of all the devices does not exceed

100. Load Number: 0.2B AC

“AVIS: - L ´étiquette du ministère des Communications du Canada identifie le matériel homologué. Cette étiquette certifie que le matériel est conforme a certaines normes de protection, d ´ exploitation et de sécurité des réseaux de télécommunications. Le ministère n ´ assure toutefois pas que le matériel fonctionnera a la satisfaction de l ´ utilisateur.

Avant d ´ installer ce matériel, l ´ utilisateur doit s ´ assurer qu´ il e st permis de le rac co rder a ux ins talla tions de l ´ enterprise locale de télécommunication. Le matériel doit également etre installé en suivant une méthod acceptée de raccordement. Dans certains cas, les fils intérieurs de l´ enterprise utilisés pour un service individuel a ligne unique peuvent etre prolongés au moyen d´ un dispositif homologué de raccordement (cordon prolongateur téléphonique interne). L ´ abonné ne doit pas oublier qu ´ il est possible que la conformité aux conditions énoncées ci-dessus n ´ empechent pas le dégradation du service dans ce rtaines si tuations. Actuellement, les enterprises de télécommunication ne permettent pas que l ´ on raccorde leur matériel a des jacks d ´ abonné, sauf dans les cas précis prévus pas les tarrifs particuliers de ces enterprises.

Les réparations de matériel homologué doivent etre effectuées pas un centre d ´ entretien canadien autorisé désigné par le fournisseur. La compagne de télécommunications peut demander a l ´ utilisateur de débrancher un appareil a la suite de réparations ou de modifications effectuées par l ´ utilisateur ou a cause de mauvais fonctionnement.

Pour sa propre protection, l ´ utilisateur doit s ´ assurer que tous les fils de mise a la terre de la source d ´ énergie électrique, des lignes téléphoniques et des canalisations d ´´ eau métalliques, s ´ il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions rurales.

Avertissment. - L ´ utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recours a un service d ´ inspection des installations électriques, ou a electricien, selon le cas”.

Une note explicative sur les indices de charge (voir 1.6) et leur emploi, a l ´ intention des utilisateurs du matériel terminal, doit etre incluse dans l ´ information qui accompagne le materiel homologué. La note pourrait etre rédigée selon le modèle suivant:

“L ´ indice de charge (IC) assigné a chaque dispositif terminal indique, pour éviter toute surcharge, le pourcentage de la charge totale qui peut etre raccordée a un circuit téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit bouclé peut etre constituée de n ´ import somme des indices de charge de l ´ ensemble des dispositifs ne dépasse pas 100.”

L ´ Indice de charge de cet produit est ____________.

Tradema rks

ITI, SuperBus, and ITI ToolBox are registered trademarks of Interactive Technologies, Inc. Concord and SnapCard are trademarks of Interactive Technologies, Inc. X-10 is a registered trademark of X-10 (USA), Inc.

This manual may refer to products that are announced but are not yet available.

651/777-2690

651/779-4890

Page 5

About This Manual

This manual provides information for planning, installing, programming, and testing this security system. When necessary, this manual refers you to other documentation included with compatible peripherals.

Planning sheets are included for you to record hardware layout and software programming settings.

About the User’s Manual

The User’s Manual (466-1513-01) contains user worksheets that should be filled out during the installation and programming of the system. With two partition systems, a User’s Manual for each partition is suggested.

Special Installation Requirements

This security system can be used as a fire warning system, an intrusion alarm system, an emergency notification system, or any combination of the three.

Some installations may require configurations dictated by city/ state codes, insurance, or Underwriter’s Laboratories (UL). This section desc ribes the various co mponent and configuration listings.

UL Listed Installations

This section describes the requirements for UL Listed installations.

Basic System

Control Panel (60-7 34 -0 1 or 60-7 92 -0 1- 9 5R)

❑ ❑ Backup Battery 12V 4 AH (60-681) or 12V 7 AH (60-

680)

❑ SuperBus 2000 Fixed Display Touchpad (60-820), 2x16

LCD Touchpad (60-746-01), 2x20 LCD Touchpad (60-

803), or VFD Touchpad (60-804)

❑ Standard Class II 24 VAC, 30 VA Power Transformer

(60-761), Class II 24 VAC, 30 VA Line Carrier Power Transformer (60-762), or Standard Class II 24 VAC, 50 VA Power Transformer ( 6 0- 77 8) , Cla s s I I 24 VAC, 50 VA Line Carrier Power Transformer (60-779)

❑ Interior Speaker Sir e n (60-528), Exterior Speaker Siren

(13-060), Slim Line Hardwire Interior Siren (60-483-01) or Hardwire Exterior Siren (13-046)

Basic system may also include a SuperBus 2000 RF Receiver (60-764-01-95R-16Z) or (60-764-01-95R-32Z) or (60-764-01-95R-MAX).

Household Burglary Alarm System Unit (UL 1023)

Basic system, plus:

❑ Hardwire Magnetic Contact (13-068 or 13-071) or

Wireless Learn Mode Door/Window Sensor (60-362)

❑ IMMEDIATE TROUBLE BEEPS set to on ❑ UL 98 OPTIONS set to on (see page 41) ❑ RECEIVER FAILURE set to on (if wireless devices are

used)

❑ SIREN VERIFY set to on

About This Manual

❑ EXIT DELAY set to 60 seconds ❑ QUICK EXIT set to off ❑ EXIT EXTENSIONset to off ❑ SIREN TIMEOUT set to 4 minutes or more ❑ ENTRY DELAY set to 45 seconds or less ❑ AC FAILURE set to on ❑ RF TX TIMEOUT set to 24 hours (if system includes a

built in or SuperBus 2000 RF Receiver and wireless smoke sensors)

Household Fire Warning System (UL 985)

Basic system, plus:

❑ Hardwire Smoke Detector:

System Sensor models 2100D, 2100TD, 2100S, 2100TS, 2400, or 2400TH learned into sensor group 26 or Sentrol (ESL) models 429AT, 521B or 521BXT learned into sensor group 26

❑ Wireless Smoke Sensor 60-506-319.5 or 60-838-95

learned into sensor group 26

❑ IMMEDIATE TROUBLE BEEPS set to on ❑ UL 98 OPTIONS set to on (see page 41) ❑ RECEIVER FAILURE set to on ❑ SIREN VERIFY set to on ❑ AC FAILURE set to on ❑ RF TX TIMEOUT set to 4 hours (if system includes a

built in or SuperBus 2000 RF Receiver and wireless smoke sensors)

UL 1023 & 985 24-Hour Backup

For 24-hour backup, the total current draw fo r all con-

❑

nected devices is limited to 90 mA (during normal standby conditions) using a 4.0 AH battery, or 190 mA (during normal standby conditions) using a 7.0 AH battery.

Commercial Burglary Alarm System Unit (Grade C UL

Basic system using Control Panel 60-801-01 plus:

1610)

❑ Hardwire Magnetic Contact (13-068 or 13-071) or Wire-

less Learn Mode Door/Window Sensor (60-499)

❑ ITI SAW PIR Sensor (60-639-95R), ITI Crystal PIR Sen-

sor (60-703-95R), or DS924i P I R Sensor (60-511-01-95)

❑ IMMEDIATE TROUBLE BEEPS set to on ❑ UL 98 OPTIONS set to on (see page 41) ❑ RECEIVER FAILURE set to on (if wireless devices are

used)

❑ RF TX TIMEOUT set to 4 hours ❑ 24-HOUR TAMPER set to on ❑ SYSTEM TAMPER set to on ❑ AUTO PHONE TEST set to on ❑ PHONE TEST FREQ. set to 1 ❑ NEXT PHONE TEST set to 1 ❑ SIREN VERIFY set to on ❑ AC FAILURE set to on

UL 1610 24-Hour Backup

Same as UL 1023 & 985

❑

UL 1635 Digital Alarm Communicator System

Same as UL 1023 & 985

❑

DRAFT 8/17/00

Page 6

Planning the Installation

Central Station Reporting

The panel has been tested with the following central station receivers using SIA and Contact ID reporting formats:

❑ ITI CS-5000 Central Station Receiver ❑ Sur-Gard Central Station Receiver with models

SG-DRL2A and SG-CPM2

❑ AC FAILURE set to on

UL Canada Listed Installations

This section describes the requirements for CUL (UL Canada) Listed installations.

Canadian Standards CSA Certified Accessories Residential Burglary Alarm System Unit

(ULC-S309)

Basic system as described for “UL Listed Installations” plus:

❑ Hardwire Magnetic Contact (13-068 or 13-071) or Wire-

less Learn Mode Door/Window Sensor (60-362)

Residential Fire Warning System Control Unit (ULC-S545-M89)

Basic system as described for “UL Listed Installations” plus:

❑ Hardwire Smoke Detector:

System Sensor models 2100D, 2100TD, 2100S, 2100TS, 2400, 2400TH learne d into Sensor Group 26, or Sentrol (ESL) models 429AT, 521B, or 521BXT learned into sensor group 26

❑ Wireless Smoke Sensor 60-506-319.5 or 60-838-95

learned into sensor group 26

❑ IMMEDIATE TROUBLE BEEPS set to on ❑ RF TX TIMEOUT set to 4 hours (if system includes

SuperBus 2000 RF Receiver and wireless smoke sensors)

Note

For 24-hour backup, external power drain is limited to 90 mA (during normal standby condition) using a 4.0 AH battery, or 190 mA continuous using a 7.0 AH battery.

California State Fire Marshall Listed Installations

Same as Household Fire Warning System (UL 985), plus:

❑ SMOKE VERIFY must be set to off

Planning the Installation

This section describes system capabilities to help you get familiar with the system. “Appendix A” provides planning sheets with tables that let you record the hardware and programming configuration of the system. Fill in all necessary information ahead of time to help prepare for system installation.

When planning the installation, keep in mind that the panel has the following capabilities (dependent upon devices used):

❑ Up to 16 SuperBus 2000 Devices ❑ Up to 76 wireless or hardwired zones

Standard Panel

The following describe the basic panel (out-of-box) hardware capabilities.

❑

Power: Input for an AC step-down, plug-in style transformer.

❑

Auxiliary Power Output: Output that supplies 8.5 to

13.5 VDC with up to 1 amp (with panel powered by 30 VA transformer) or 2 amps (with p anel power ed b y 50 VA transformer) for bus devices and hardwired detectors, such as smoke and motion detectors.

❑

Bus A and B: Input and output that provides communication between bus devices and the panel.

❑

Siren Driver: Output that can drive an 8-ohm load and provides intrusion and fire alarm sounds for partition 1.

❑

2 Onboard Outputs: Open-collector outputs that can be set up to activate other signalling devices, based on system events.

❑ Microphone Input: Input used for 2-way audio when

used in conjunction with the Interrogator 200 Audio Verification Module.

❑ 8 Supervised Hardwire Zones: Inputs for various hard-

wired detectors. Zone 8 can be set up in programming to accept 2-wire smoke detectors.

❑ Built-In SuperBus 2000 Receiver

(60-792-01-95 R only ): Allows use of up to 16 or 32 ITI

319.5 MHz. crystal and/or SAW Learn Mode wireless sensors and touchpads. Also allows supervision of Supervised Wireles s Sirens.

❑ Phone Line Connection: Allows panel to communicate

with central monitoring station and/or pagers.

SuperBus 2000 Touchpads

The following describes the different touchpads that can be used for system programming and operation.

❑ SuperBus 2000 Fixed Display Touchpad: Provides oper-

ation control and user-programming access (not installer/ dealer programming). Displays system messages and indicates system status.

❑ SuperBus 2000 2x16 LCD Touchpad: Provides com-

plete system programming and operation control. Displays system messages that prompt users for information when needed and indicates system status.

❑ SuperBus 2000 2x20 LCD Touchpad: Provides com-

plete system programming and operation control. Large display shows system messages that prompt users for information when needed and indicates system stat us.

❑ SuperBus 2000 2x20 VFD T ouchpad: Provides complete

system programming and operation control. Large fluorescent display shows system m essages th at p rompt u sers f or information when needed and indicates system stat us.

SuperBus 2000 RF Receivers

These receivers expand system wireless zone capacity by 16, 32, or the maximum zones allowed by the panel. The receivers are compatible with all ITI 319.5 MHz. crystal and SAW Learn Mode wireless sensors, touchpads, and Supervised Wireless Sirens.

DRAFT 8/17/00

Page 7

Installing the System

Power Line Carrier Card

Adding this card (which requires that the panel be powered using a Power Line Carri e r Transformer) adds the following capabilities to the system:

❑ Allows the use of Supervised Wireless Sirens. ❑ Allows the use of X-10 Powerhouse Lamp Mod ules for

light control and li ght acti v a ti on dur i ng al arms.

Phone Supervision Card

Adding this card allows the panel to check for the correct phone line voltage (partition 1 only), upon dialing the central station/pager number. The panel can also be programmed to check the phone line voltage automatically.

Supervised Wireless Siren

Supervised Wireless Sirens plug into any standard electrical outlet and produce status and alarm sounds. The panel sends signals to the siren through the Power Line Carrier Card and Line Carrier Power Transformer, through the AC electrical wiring.

The siren has a built-in transmitter that is used for supervising with the panel. With the siren transmitter learned into panel memory (panels with receivers), the siren can notify the panel if it is unplugged, stops receiving panel signals, or has a low backup battery.

SuperBus 2000 Phone Inter face/Voice Module

This module allows system access and control using touchtone telephones , on- or of f -si te. T he modul e in clude s an outp ut for a speaker that sounds system status and alarm voice messages.

SnapCards

The following SnapCards expand the system as described:

❑ 8Z Input SnapCard: Provides eight additional hardwire

zone inputs, of which two are dedicated for using 2-wire smoke detectors.

❑ 4 Output SnapCard: Provides four form C relay outputs

that can be set up to activate other signalling devices, based on system events, schedules, or direct control.

❑ 4Z Input/2 Output Combo SnapCard: Provides three

hardwire zone inputs, one two wire smoke detector l oop, and two outputs that can be set up to activate other signalling devices, based on system events, schedules, or direct control.

SuperBus 2000 8Z Input Module (HIM)

Provides eight additional hardwire zone inputs.

SuperBus 2000 4-Relay Output Module (HOM)

Provides four form C relay outputs that can be set up to activate other signalling devices, based on system events.

Interrogator 200 Audio Verification Module

Adding this module allows central station operators to listen-in and talk to occupants on the premises, to verify the emergency when an alarm report is received.

Installing the System

This section describes how to install the system control panel. Before starting the installation, plan your system layout and programming using the worksheets provided in Appendix A.

Installing the system consists of the following:

❑ Determining the Panel Location ❑ Total System Power and Wire Length Guidelines ❑ Mounting the Panel ❑ Identifying Panel Main Components ❑ Installing the Optional Power Line Carrier Card ❑ Installing Optional SnapCards ❑ Connecting Detection Devices to Panel Zone Inputs ❑ Connecting Speakers ❑ Connecting Piezo Sirens ❑ Connecting an Interrogator 200 Audio Verification

Module

❑ Connecting Alphanumeric and Fixed Display Touchpads ❑ Installing SuperBus 2000 Modules ❑ Installing an RJ-31X Phone Jack ❑ Connecting the Phone Line to the Panel with a DB-8 Cord ❑ Connecting the AC Power Transformer ❑ Powering Up the Panel

DRAFT 8/17/00

Page 8

Installing the System

Determine the Panel Location

Before permanently mounting the panel, determine panel location using the following guidelines:

❑ Centrally locate the panel with relation to detection

devices whenever possible, to help reduce wire run lengths and labor.

❑ Locate the panel where the temperature will not exceed

120°F (49°C) or fall below 32°F (0°C) .

❑ Avoid running wires parallel with electrical wiring or fix-

tures such as fluorescent lighting, to prevent wire runs from picking up electrical noise.

❑ Mount the panel at a comfortable working height (about

45 to 55 inches from the floor to the bottom of the panel, as shown in Figure 1).

❑ Leave space to the left and right of the panel for wiring,

phone jack, and mounting optional modules.

❑ For wireless panels or hardwire panels that include a

SuperBus 2000 RF Receiver, allow at least 9 inches above the panel cabinet for antennas.

❑ Allow at least 24 inches in front of the panel to open the

panel door.

19.25"

12"

ANTENNA

AREA

PANEL

45-55"

Figure 1. Determining Panel Location

NOTE ALLOW AT LEAST 24" IN FRONT OF PANEL TO ALLOW FOR OPENING CABINET DOOR AND ACCESS TO PANEL COMPONENTS.

FLOOR

PHONE JACK AND

OPTIONAL MODULE

MOUNTING AREA

21"

12"

Table 1 describes the maximum wire length allowed between compatible devices and the panel, including the maximum current draw of each device.

Table 1. Maximum Device Wire Length and Current Draw

Device Max. Wire

Length to Panel

SuperBus 2000 2x16 LCD Alphanumeric Touchpad

SuperBus 2000 2x20 LCD Alphanumeric Touchpad

SuperBus 2000 2x20 VFD Alphanumeric Touchpad

SuperBus 2000 Fixed Display Touchpad

22 ga.—300 ft. 18 ga.—750 ft.

22 ga.—250 ft. 18 ga.—600 ft.

22 ga.—300 ft. 18 ga.—700 ft.

SuperBus 2000 RF Receiver 22 ga.—1,100 ft.

Max. mA

Draw

90 mA

120 mA

120 ma

65 mA

30 mA

18 ga.—2,800 ft.

SuperBus 2000 Ph one Interface/Voice Module

22 ga.—40 ft. 18 ga.—120 ft.

600 mA

Power Line Carrier Card N/A 110 mA 4 Input/2 Output SnapCard N/A 185 mA* 8Z Hardwire Z one Exp ander

N/A 230 mA*

SnapCard 4 Output SnapCard N/A 130 mA* SuperBus 2000 8Z Input

Module SuperBus 2000 4-Relay Out-

put Module SuperBus 2000 Energy

Saver Module Interrogator 20 0 22 ga.—3,200 ft.

22 ga.—1,800 ft. 18 ga.—4,500 ft.

22 ga.—350 ft. 18 ga.—900 ft.

22 ga.—1,600 ft. 18 ga.—4,000 ft.

35 mA

180 mA

20 mA

10 mA

18 ga.—4,500 ft.

Interrogator AVM 22 ga.—110 ft.

300 mA

18 ga.—260 ft.

*Maximum current draw for the SnapCards does not include the load which may be applied to their auxiliary DC supply.

Table 2 describes the total system wire lengths allowed when installing systems using unshielded or shielded cable.

Table 2. Total System Wire Length

Allowed

Total System Power and Wire Length Guidelines

The panel can supply up to 1 amp (1,000 mA) when powered by the 24 VAC, 30 VA transformer or up to 2 am ps (2 ,000 mA) when powered by the 24 VAC, 50 VA transformer for system devices.

The total system wire length allowed can vary depending on devices powered by the panel, the wire length between devices and the panel, and the combined wire length of all devices.

Wire Type Total System

22-gauge, unshielded 22-gauge, shielded 18-gauge, unshielded 18-gauge, shielded

4,500 ft. 3,000 ft. 3,500 ft. 2,200 ft.

Wire

DRAFT 8/17/00

Page 9

Installing the System

CAUTION

Table 3 describes the minimum current draw of each device when the panel is operating only from the backup battery. For 24-hour backup, the total current draw of all SnapCards connected to the panel and devices conn ected to +12 BUS (panel terminal 4) is limited to 90 mA (during normal standby condition) using a 4.0 AH battery, or 190 mA (during normal standby condition) using a 7.0 AH battery.

Table 3. Minimum Device Current Draw

Device Min. mA

Draw

SuperBus 2000 2x16 LCD Alphanumeric

15 mA

Touchpad SuperBus 2000 2x20 LCD Alphanumeric

15 mA

Touchpad SuperBus 2000 2x20 VFD Alphanumeric

15 mA

Touchpad SuperBus 2000 Fixed Display Touchpad 11 mA SuperBus 2000 RF Receiver 27 mA SuperBus 2000 Phone Interface/Voice Module 25 mA Power Line Carrier Card N/A 4 Input/2 Output SnapCard 20 mA 8Z Hardwire Zone Expander SnapCard 38 mA 4 Output SnapCard 1 mA SuperBus 2000 8Z Input Module 18 mA SuperBus 2000 4-Relay Output Module 12 mA SuperBus 2000 Energy Saver Module 20 mA Interrogato r 20 0 10 mA Interrogato r AVM 45 mA

After determining panel location, run all necessary wires to that location using the guidelines in Table 4.

T able 4. Device W irin g Re qu ir em en ts

Device Wire Requirements

AC Power Transformer 2-conductor, 18-gauge, 25 feet

maximum

Earth Ground Single conductor, 16-gauge

solid, 25 feet maximum Telephone (RJ-31X) 4-conductor Detection Devices 2- or 4-conductor, 18- to 22-

gauge, 300 ohms maximum

loop resistance including device Speakers 2-conductor, 22-gauge, 175 feet

maximum

2-conductor, 18-gauge, 440 feet

maximum SuperBus 2000 Devices 4-conductor, 22- or 18-gauge Interrogator 200 AVM

4-conductor, 22-gauge, shielded Power and Microphone

Table 4. Device Wiring Requirements

Device Wire Requirements

2-Wire Smoke Detectors 2-conductor, 22-gauge, 330 feet

maximum 2-conductor, 18-gauge, 830 feet maximum (based on 10 ohms maximum loop resistance plus a 2k-ohm, end-of-line resistor)

Mounting the Panel

Use the following procedure to mount the panel to the wall or wall studs.

Make sure you are free of static electricity whenever you work on the panel with the cover open. To discharge any static, first touch the metal panel chassis, then stay in cont act with the chass is when touchin g the circuit board. Using an approved grounding strap is recommended.

To mount the panel:

1. Open the panel door and remove the necessary wirin g knockouts (see Figure 2). Be careful not to dama ge the circuit board.

2. Feed all wires through wiring knockouts and place the panel in position against the wall.

3. Leve l t he panel and mark the top an d bottom mounting holes (see Figure 2).

4. Install anchors where studs are not present.

5. Partially insert screws into the two top mounting hole locations, then hang the panel on the two screws.

6. Recheck for level, insert the two lower screws, and tighten all four mounting screws.

M OUNTING HO LES

KNOCKO UTS

M OUNTING HO LES

8573126A.DS

Figure 2. Mounting the Panel (Hardwire Panel Shown—

Combination Hardwire/Wireless Panel Similar)

DRAFT 8/17/00

Page 10

Installing the System

Identify Panel Components

Before installing devices and making wiring connections, familiarize yourself with the main panel components. Figure 3 shows the main component locations for the hardwire circuit board and Figure 4 the main component locations for the combination hardwire/wireless circuit board.

BACKUP BATTERY CONNECTIONS

EEPROM

BLACK

RED

POWER LINE CARRIER CARD HEADERS

PROGRAMMING TOUCHPAD HEADER

MICRO PROCESSOR

PHONE SUPERVISION CARD HEADERS

TERMINAL STRIP

Figure 3. Hardwire Circuit Board Main Components

SNAP CARD HEADER

8573G10B.DSF

Installing Antennas

Install the antennas (included with panel) into the inside terminal of each antenna terminal block on the combination hardwire/wireless panel (see Figure 5).

CONNECT TO

INSIDE TERMINAL

ANTENNA TERMINAL BLOCKS

BACKUP BATTERY CONNECTIONS

BLACK

POWER LINE CARRIER CARD HEADERS

RED

MICRO PROCESSOR

PROGRAMMING TOUCHPAD HEADER

TERMINAL STRIP

EEPROM

PHONE SUPERVISION CARD HEADERS

Figure 4. Combination Hardwire/Wireless Circuit

Board Main Components

SNAP CARD HEADER

8573G206C.DSF

8573207A.DS

Figure 5. Installing the Antennas

Connecting the Panel to Earth Ground

For maximum prot ect ion from lightning strikes and trans ients, connect the lower-left circuit board screw to earth ground as shown in Figure 6. Use 16-gauge, solid copper wire from an earth grounded cold water pipe clamp to the panel.

TO WATER PIPE

PIPE

GROUND CLAMP

Figure 6. Connecting the Panel to Earth Ground (Hard-

wire Panel Shown—Combination Hardwire/ Wireless Panel Similar)

8573110A.DS

Note

For best results, it is recommended that you crimp a spade lug on the w ire end at the panel and secure t he lug under the circuit boa rd scre w as show n in F igure 6.

DRAFT 8/17/00

Page 11

Installing the System

8573127A.DSF

SNAP CARD

SCREW LO CATIONS

CONNECTOR

SNA P CARD HEADER

Installing the Optional Power Line Carrier Card (60-755)

The Power Line Carrier card lets you add Supervised Wireless Sirens for alarm and status sounds and X-10 Lamp Modules for controlling lights.

Install the card on the header pins as shown in Figure 7. No wiring or programmin g i s necessary.

Note

The lower header has two jumpers installed from the factory that must be removed before installing the Power Line Carrier Card. Leave these jumpers in place if you are not installing a Power Line Carrier Card.

POWER LINE CARRIER CARD MOUNTING LOCATION

JUMPERS

TERMINAL STRIP

Installing Optional SnapCards

The SnapCard Header on the right side of the panel allows for installation of one SnapCard.

Install the desired SnapCard onto the panel SnapCard Header and secure it in place with two screws, included with the card (see Figure 9).

POWER LINE CARRIER CARD HEADERS

Figure 7. Installing the Power Line Carrier Card (Hard-

wire Panel Shown—Combination Hardwire/ Wireless Panel Similar)

8573G96A.DSF

Installing the Optional Phone Supervision Card (60-789)

The Phone Supervision Card allows the panel to check the phone line voltage (partition 1 only), upon dialing the central station/pager number. The panel can also be programmed to check the phone line voltage automatically (see “Line Fail Delay” on page 33).

Install the card on the header pins as shown in Figure 8.

TERMINAL STRIP

PHONE SUPERVISION CARD

Figure 9. Installing a SnapCard into the Panel

Expansion Connector (Hardwire Panel Shown—Combination Hardwire/Wireless Panel Similar)

Connect all necessary input/output wiring using the Installation Instructions included with the card.

8636G02A.DSF

Figure 8. Installing the Phone Supervision Card (Hard-

DRAFT 8/17/00

wire Panel Shown—Combination Hardwire/ Wireless Panel Similar)

PHONE SUPERVISION CARD HEADERS

Page 12

Installing the System

22 23

ZONE

+12V

2W SMK

2k Ohm

EOL RESISTOR

49-454

(LOCATE AT LAST

DETECTOR)

PAN EL TERMINALS

8573G 26A .D SF

Connecting Detection De vices to P anel Zone Inputs

Zone inputs 1 through 8 are supervised using a 2k-ohm, end-of-line resistor at the last device on the circuit. All eight zones accept either normally open (N/O) or normally closed (N/C) detection devices.

Connecting Intrusion Detection Devices

Figure 10 shows the typical wiring for N/C and N/O door/window intrusion detection.

GND

ZONE

NORMALLY

OPEN

(N/O)

CONTACTS

IN PARALLEL

2k Ohm

EOL RESISTOR

49-454

PAN EL TERMINALS

NORMALLY

CLOSED

(N/C) CONTACTS IN SERIES

ZONE

13 14 15

Connecting 2-Wire Smoke Detectors

Zone input 8 can be set up (in program mode) to accept the following 12 VDC, 2-wire smoke detectors:

❑ System Sensor models 2100D, 2100TD, 2100S, 2100TS,

2400, 2400TH

❑ Sentrol (ESL) models 429AT, 521B, 521BXT—(models

521B and 521BXT requ i re the following dip switc h settings: 1-on, 2-off)

CAUTION

Use only the 2-wire sm ok e d ete cto r mo de ls des cribed above. Alarm signals from other detectors may not be processed correctly if t he panel has lo st AC power and is operating only from the backup battery.

When set up for 2-wire smoke detectors, zone 8 can handle up to 10 smoke detectors with 120 uA maximum idle cur rent per detector. Maximum total loop current allowed in an alarm condition is 100 mA.

Note

When using 2-wire smoke detectors on zone 8, the TWO-WIRE SMOKE setting (in program mode) must be turned on menu. See

before

entering the LEARN SENSORS

ONBOARD OPTIONS—INPUTS

in the

section “Programming the Panel” for compl ete detai ls .

Connect one or more, 2-wire smoke detectors to the panel as shown in Figure 12.

2k Ohm

EOL RESISTOR

8573G23A.DS4

49-454

Figure 10. Connecting N/C and N/O Intrusion Detection

Circuits to the Panel

Figure 11 shows the typical wiring for a Detection Systems model DS922 (ITI part no. 13-082) motion detector. The minimum available panel voltage for hardwired PIR motion detectors is 8.5 VDC (9.5 VDC for UL listed installations).

+ 12 BUS

PAN EL TERMINALS

GND

20 21

ZONE

Figure 12. Connecting 2-Wire Smoke Detectors to the

Panel

2k Ohm EOL RESISTOR

49-454

(LOCATE AT SENSOR)

8573140A.D S

Figure 11. Connecting a Motion Detector to the Panel

DRAFT 8/17/00

Page 13

Connecting 4-Wire Smoke

CAUTION

Detectors

Zone input 8 can be used with 4-wire smoke detectors that latch and remain in the alarm state until power is removed, then restored to the detector. The panel provides this power interruption from terminal 23 (2-wire smoke power +), provided that zone 8 is learned into sensor group 26 (fire).

Note

The TWO-WIRE SMOKE setting (in program mode) must be

ONBOARD OPTIONS—INPUTS

off

when using 4-wire smoke detectors. See

in the section “Pro-

gramming the Panel” for complete details.

Table 5 describes the minimum available panel power. Use only 4-wire smoke detectors that operate at these power limits. Connect up to five Sentrol (ESL) model 449AT (ITI part no. 13-360) smoke detectors to panel power and zone 8 input as shown in Figure 13.

Table 5. Panel Minimum Available Power

Min. Voltage/Max. Current Available

8.3 VDC, up to 30 m A to tal (combined alarm) current

8.1 VDC, up to 40 m A to tal (combined alarm) current

7.7 VDC, up to 60 m A to tal (combined alarm) current

7.4 VDC, up to 80 m A to tal (combined alarm) current

Note

Zone 8 must be learned into sensor group 26 (fire) for connected smoke detectors to reset after canceling a fire alarm.

PAN EL TERMINALS

ZONE

GND

C O

. . . . . . . .

C O

. . . . . . . .

2k Ohm

EOL RESISTOR

49-454

(LOCATE AT LAST

DETECTOR)

C O M

ZONE

N ONO

NON

Installing the System

+12V

2W SMK

MODEL

449AT

MODEL

449AT

8573139A.D S

Figure 13. Connecting 4-Wire Smoke Detectors to Panel

Power and Zone 8 Input

Connecting Spe akers

The panel provides one siren driver output for intrusion (steady), fire (temporal 3), and auxiliary (on-off-on-off) alarm sounds. This output trips only for partition 1 alarms.

The output can drive a single 8-ohm speaker or multiple speaker circuit of 8 ohms or higher (as shown in the following speaker wiring diagrams). Compatible speakers are described on the following page.

To avoid disabling the panel speaker output, do not make speaker connec tions with the pa nel pow ered u p.

DRAFT 8/17/00

Page 14

Installing the System

15-Watt Speaker (13-060)

Use this speaker for exterior siren applications. Connect the speaker to the panel as shown in Figure 14.

SPEAKER

7 8

SPLICE

8573G 31A .D SF

Figure 14. Connecting Speakers to the Panel

2 8-OHM SPEAKERS

IN SERIES (16 OHMS)

SPEAKER

7 8

Hardwire Interior Speaker (60-528)

Use this speaker unit for interior siren applications. Connect the speaker to the panel as shown in Figure 15.

CAUTION

Connect only the large speaker to panel terminals 7 and 8 as shown. The smaller speaker cannot handle the output of terminals 7 and 8 and should not be connected, to avoid damaging the speaker.

Connect two units to the panel terminals with speakers in series (16 ohms), as shown in Figure 16.

NOT

USED

PANEL TERMINALS

Figure 16. Connecting T wo Har dwire Interior Speaker w/

Dual Speaker Units to Panel Terminals

SPEAKER

NOT

USED

8573103A.DSF

PANEL TERMINALS

SPEAKER

Figure 15. Connecting the Hardwire Interior Speaker w/

Dual Speakers to the Panel

NOT

USED

8573102A.DSF

Connecting Piezo Sir e ns

Output 1

Onboard output 1 (OUT 1—terminal 9) is an open-collector (switched path-to-ground), programmab le output that can handle a maximum of 200 mA current sink. The default setting (01614) activates the output 15 seconds after a po lice or fire alarm condition occurs. This allows you to connect a piezo siren without changing the output configuration number in programming. This output is typically used for exterior siren application.

Output 2

Onboard output 2 (OUT 2—terminal 10) is an open-collector (switched path-to-ground), programmab le output that can handle a maximum of 200 mA current sink. The default setting (01710) activates the output for status and alarm tones, allowing for a piezo siren connection without changing the output configuration number.This output is typically used for interior siren application.

For more information on output configuration numbers, see “Onboard Options Menu” on page48.

DRAFT 8/17/00

Page 15

Installing the System

Note

P T

Exterior Sirens

Hardwire Exterior Siren (13-046)

Connect the siren to panel as shown in Figure 17.

OUT 1

+12V

4 9

RED

BLACK

Figure 17. Connecting the Hardwire Exterior Siren to

the Panel

PAN EL TERMINALS

8690G 26A .D S F

Interior Sirens

Interior Piezo Siren (30-006)

Connect the piezo siren to the panel terminals with a 2k-ohm resistor, as shown in Figure 18.

Note

Piezo siren connections to terminal 10 require a 2k resistor that can be located at the panel, since it does not supervise the circuit.

Note

If using an external power supply instead of panel terminal 4, the supply v olta ge m ust be limit ed t o 9.5 VDC maximum and the negative side of the power supply must be connected to panel ground (terminal 3).

+12V

ANEL ERM IN ALS

OUT2

2k OHM RESISTOR 49-454

RED

BLACK

Slim Line Hardwire Interior Siren (60-483-01)

Connect the siren to the panel as shown in Figure 19.

The volume switch settings inside the siren do not affect the siren output.

OUT2

NOT USED

+12V

4 10

PAN EL TERMINALS

8573G 27A .D SF

HIGH2GND3LOW

Figure 19. Connecting the Slim Line Hardwire Interior

Siren to the Panel

Installing Supervised Wireless Sirens (60-736-95)

Supervised Wireless Sirens (SWS) plug directly into electrical outlets and are not wired to the panel. The panel (when powered by a line carrier power transformer) sends alarm and status messages to the siren, along the building AC wiring.

For supervised operation, the siren has a built-in transmitter that, when learned into panel memory, transmits to the panel receiver if the siren has a low battery or other trouble condition.

Before plugging in Supervised Wireless Sirens, the panel must be powered up and partition House Codes and the SWS Supervision Code set (in program mode) to the desired settings.

The following procedures describe the basic steps for installing Supervised Wireless Sirens. For complete installation details, refer to the Supervised Wir eless S iren Installation Instructions, included with each siren.

Figure 18. Connecting an Interior Piezo Siren

DRAFT 8/17/00

8690G 27A .DS F

Regardless of sup ervised or unsup ervised s iren in stallation, you must follow the order of installation as described to avoid learning the wrong (or undesired) House Code and SWS Supervision Code into siren memory.

For unsupervised wireless siren installations:

1. Power up the panel (see “Powerin g Up the Panel” later in this section).

2. Enter program mode and set the partition House Code to the desired setting (see the LIGHT CONTROL menu in the section “Programming the Panel”).

3. Exit program mode.

4. Install the siren backup battery.

5. Plug the siren into an electrical outlet.

6. Press the STATUS button on any working touchpad. The siren should beep once an d the siren LED should flash 5 times, indicating it has learned the partition House Code.

Page 16

Installing the System

7. If the siren d oesn ’t beep or the LED doesn’t flash, reset the house code on the siren by pressing and holding its button for 20 seconds. The siren will beep three times when the memory has been cleared. Repeat step 6.

For supervised wireless siren installations:

Note

Hardwire Concord 2.0 panels must have a Super Bus 2000 RF Receiver installed for supervised wireless siren operation.

1. Power up the panel (see “Powerin g Up the Pan el” later in this section).

2. Install the siren backup battery.

3. Cl ear the siren memory by pressing and holdin g the siren button for 20 seconds. The siren will beep three times when the memory has been cleared.

4. Enter program mode and set the partition House Code to the desired setting (see the LIGHT CONTROL menu in the section “Programming the Panel”).

5. Proceed to the SIREN OPTIONS menu and set the SWS Supervision Code to the desired setting.

6. Proceed to the LEARN SENSORS menu and select the desired partition, sensor group 33, and the desired sensor number.

7. When the touchpad display shows TRIP SENSOR nn, plug the siren into an electrical outlet. The siren should beep once and the siren LED should flash 10 times, indicating the panel learned the siren transmitter ID and that the siren learned both the partition House Code and SWS Supervision Code.

8. Exit program mode.

Note

When installing Supervised Wireless Sire ns for supervised operation, be sure to program sensor text that clearly identifies each siren. For example,

SIREN

BASEMENT SIREN

. This can help b oth y ou

HALLWAY

and your customer locate a specific siren if a problem occurs.

BLACK

YELLOW

SPLICE

RUN SEPARATE WIRE CABLES AS SHOWN

CABLE SHIELD

PANEL TERMINALS

SPEAKER

Figure 20. Connecting an Interrogator 200 AVM to the

Panel (Partition 1 use only)

+12V

GND

MIC

8573101A.DSF

Connecting Alphanu m eric and Fixed Display Touchpads

Connecting an Interrogator 200 Audio Verification M odule (60-677)

Connect the Interrogator 200 Audio Verification Module (AVM) to the panel terminals as shown in Figure 20.

CAUTION

If a speaker is already connected to panel terminals 7 and 8, the Interrogator 200 speaker must be hooke d up in series with that speaker to provide a 16-ohm load. Hooking up speakers in parallel to panel terminals 7 and 8 creates a 4-ohm load that can cause permanent damage to the panel.

Alphanumeric and Fixed Display touchpads use the same color-coded wire scheme. Connect the touchpad s to the panel power output and bus terminals as shown in Figure 21.

GND

SUPERBUS 2000

FIXED DISPLAY

TOUCHPAD

LCD ALPHANUMERIC

TOUCHPADS

Figure 21. Connecting Alphanumeric and Fixed Display

Touchpads to the Panel

+12V

3 4 5

+12V/RED

BUS B/WHITE

BUS A/GREEN

BUS

GND/BLACK

8690G01A.DSF

DRAFT 8/17/00

Page 17

Installing the System

Installing Sup erBus 2000 Modules

SuperBus modules can be installed inside the panel cabinet or away from the panel. Use the following guidelines when installing modules inside the panel cabinet:

❑ Up to 16 bus modules can be connected to the panel. (15

modules for the RF panel since receiver counts as 1.)

❑ Up to 3 modules can be mounted inside the cabinet. ❑ The panel includes two support standoffs you install to

secure module backplates to the panel (see Figure 22).

SUPPORT STANDOFF

PANEL

END

MODULE

END

8573g64A.DSF

Figure 22. Support Standoff

❑ Install the standoffs at the locations shown in Figure 23.

Note

Even if you don’t plan to mount modules inside the cabinet, instal l the su pport standoffs f o r future use and to avoid losing them.

receivers must be installed outside the cabinet.

TOP

MOUNTING

CLIPS (6)

DETAIL

SIDE MOUNTING CLIP

RF RECEIVER MODULE (COVER REMOVED)

PANEL CABINET

SUPPORT

STANDOFFS

8573107A.DSF

Figure 23. Installing the Support Standoffs (Hardwire

Panel Shown—Combination Hardwire/Wireless Panel Similar)

❑ The cabinet has built-in mounting clips on the top and

sides that module backplates slide onto for mounting (see Figure 23).

❑ One SuperBus 2000 RF Receiver can be installed inside

the cabinet, but it must be mounted on the right-hand side to accommodate the antennas (see Figure 24). Additional

SUPPORT STANDOFF

8573G37B.DSF

Figure 24. Mounting SuperBus 2000 Modules Inside the

Cabinet (RF Receiver Shown)

SuperBus 2000 RF Receiver (60-764-01-95R-16Z/32Z/MAX)

1. Moun t the receiver inside the cabinet enclosure as shown in Figure 24.

2. Connect the receiver to the panel as shown in Figure 25.

+12V

GND

PANEL TERMINALS

RECEIVER MODULE TERMINAL STRIP

3 4

+12V

Figure 25. Connecting the SuperBus 2000 RF Receiver

to the Panel T erminals

BUS

GND

8573105A.DS

DRAFT 8/17/00

Page 18

Installing the System

SuperBus 2000 Phone Interface/Voice Module (60777-01)

The Phone Interface/Voice Module includes two backplates for mounting the module inside the control panel cabinet. The module can also be mounted outside of the control panel using an optional plastic housing (part no. 60-800). Refer to the SuperBus

8998g18A.DSF

2000 Phone Interface/Voice Module Installation Instructions included with

each module, for complete mounting instructions.

Note

In UL Listed installations, the Phone Interface/Voice Module is for supplementary use only.

The module requires pa nel power and bus connections, phone line connection through panel terminals and DB-8 cord (from an RJ-31X jack), and speaker connection throu gh panel terminals.

PHO N E INTERFA CE/VO IC E M ODULE TERMINAL STRIP 1

+12V

2A3B4

PAN EL TERMINALS

GND5GND

SPK1

GRN BRN

GREEN

PHO N E INTERFA CE/VO IC E M ODULE TERMINAL STRIP 2

SPK28AUD19AUD210GND

GRY

RED

26 27

GRAY

BROWN

BRN

TIP112TIP213RING

RED

DB-8 CORD

PLUG

GRY

RING

Wiring—Power

Connect the module to the panel power and bus terminals as shown in Figure 26.

PHO N E INTERFA CE/VO IC E M ODULE TERMINAL STRIP 1

2A3B4

+12V

GND

3 4

PANEL TERMIN ALS

GND5GND6SPK17SPK28AUD19AUD210GND11TIP112TIP2

+12V

BUS

Figure 26. Connecting the Phone Interface/Voice

Module to the Panel Power and Bus Terminals

PHO N E INTERFA CE/VO IC E M ODULE TERMINAL STRIP 2

RING

8573108A.dsf

RING

Wiring—Phone Line

Connect the phone line to the module through the panel terminals and DB-8 cord (from an RJ-31X jack) as shown in Figure

27.

Note

For RJ-31X connections, see “Installing an RJ-31X Phone Jack (13-081)” on page 20.

RJ-31X

JACK

GRN RED

8573109A.dsf

Figure 27. Connecting a Phone Line to the Module

Wiring—Speaker (Status Voice Messages Only)

Connect an interior speaker to the Phone Interface/Voice module terminals as shown in Figure 28. When connected as shown, the speaker only produces status voice messages. In an alarm situation the speaker will announce voice status messages.

Note

To prevent status voice messages from being broadcast outside, do not connect exterior speakers to Phone Interface/Voice module terminals 6 and 7.

PHO N E INTER FACE/VO IC E M ODULE TERMINAL STRIP 1

2A3B4

+12V

GND5GND6SPK17SPK28AUD19AUD210GND11TIP112TIP213RING

PHO N E INTER FACE/VO IC E M ODULE TERMINAL STRIP 2

RING

HARDW IRE IN T E R IO R SPEAK ER 60-528

NOT

USED

Figure 28. Connecting an Interior Speaker to the Phone

Interface/Voice Module (Status Messages

8690G28A.DSF

Only)

DRAFT 8/17/00

Page 19

Installing the System

Wiring—Speaker (Status and Alarm Messages)

Make the following connection only if the Phone Interface/ Voice module is being installed in partition 1 and alarm sounds are desired from the speaker connected to the terminals. In an alarm situation, the speaker will alternate between alarm siren tones and voice status messages.

PHO N E INTER FACE/VO IC E M ODULE TERMINAL STRIP 1

2A3B4

+12V

GND5GND6SPK17SPK28AUD19AUD210GND11TIP112TIP213RING

Figure 29. Connecting an Interior Speaker to the Phone

Interface/Voice Module (Status and Alarm Messages)

PHO N E INTER FACE/VO IC E M ODULE TERMINAL STRIP 2

SPEAK ER

HARDW IRE IN T E R IO R SPEAK ER 60-528

NOT

USED

PAN EL

TERMINALS

8573130A.DSF

RING

Energy Saver Module (60-620-01)

Connect the Energy Saver Module to the panel and premises thermostat as shown in Figure 30.

THERMOSTAT

ENERGY SAVER MODULE

SuperBus 2000 8Z Input Module (60-774)

Connect the SuperBus 2000 8Z Input Module to the panel as shown in Figure 31.

ID: XXXXXXXX

1 2 3 4 5 6 7 8 9 101112131415 16

ZONE 1

ZONE COMMON

ZONE 2

ZONE 3

ZONE 4

ZONE 5

ZONE COMMON

ZONE 6

ZONE 7

ZONE COMMON

ZONE 8

PANEL TERMINALS

+12V

GND

3 4 5

BUS

8690G10A.DSF

Figure 31. Connecting the 8Z Input Module to the P an el

Terminals

Connect all necessary input wiring using the Installation Instructions included with module.

HEAT

OFF

50 60 70 80 90

TO HVAC

8573G98A.DSF

A/C

PANEL TERMINALS

Figure 30. Connecting the Energy Saver Module to the

Panel Terminals and Premises Thermostat

DRAFT 8/17/00

23456

GND

3 4 5

+12V

BUS

Page 20

Installing the System

4-Relay Output Module (60-770)

Connect the SuperBus 2000 4-Relay Output Module to the panel as shown in Figure 32.

ID: XXXXXXXX

1 2 3 4 5 6 7 8 9 101112 1314 1516 17

NO 1

NC 1

COM 1

NC 2

NO 2

COM 2

NC 3

NO 3

COM 3

NC 4

NO 4

COM 4

ZONE 1

ZONE COM

Installing an RJ-31X Phone Jack (13-081)

Use the following guidelines when installing an RJ-31X phone jack for system control by phone and central station monitoring.

❑ Locate the RJ-31X jack (CA-38A in Canada) no further

than five feet from the panel.

❑ The panel must be connected to a standard analog (loop-

start) phone line, that provides 48 volts DC (on-hook or idle) which increases to 89 to 105 volts DC (ring voltage).

Note

The panel cannot be used on a digital or PBX phone line. These systems are designed for digital type devices o nly, operating anywhere from 5 volts D C and up. The panel uses an analog modem and does not have a digital converter, adapter, or interface to operate through such systems.

❑ For full line seizure, install an RJ-31X phone jack on the

premises phone line so the panel is ahead of all phones and other devices on the line. This allows the panel to take control of the phone line when an alarm occurs, even if the phone is in use or off-hook.

❑ If an analog line is not available, contact your customer’s

telecommunications specialist and tell him/her you need an analog line off the phone switch (PBX mainframe) or a 1FB (standard business line).

+12V

GND

PANEL TERMINALS

Figure 32. Connecting the 4-Relay Output Module to the

Panel Terminals

3 4 5

BUS

8690G11A.DSF

Connect all necessary output wiring using the Installation Instructions included with the module.

Setting Device Address on SuperBus 2000 Devices

When the panel is powered up it automatically assigns device addresses to SuperBus 2000 devices.

Note

Connecting the panel to an analog line off the phone switch places the panel

ahead

of the phone system, preventing panel access from phones on the premises. However, the panel can still be accessed from off-site phones.

To connect a phone line to the panel using an RJ-31X/CA-38A jack:

1. Run a 4-conductor cable from the TELCO protector block to the jack location (see

2. Connect one end of the cable to the jack (see

A in Figure 33).

B in Figure

33).

3. At the TELCO protector block, remove the premises phone lines (lines from phone jacks on premises) from the block and splice them to the black and white (or yellow) wires of the 4-conductor cable (see

C in Figure 33).

4. Connect the green and red wires from the 4-conductor cable to the TIP (+) and RING (-) posts on the block (see

D in Figure 33).

DRAFT 8/17/00

Page 21

CAUTION

BRN

GRN

RJ-31X

JACK

GRY

RED

GRN BRN

GREEN

TELCO

HOUSE

BROWN

GRY

26 27

GRAY

Installing the System

RED

DB-8 CORD

PLUG

GREEN

BLACK

TELCO

PROTECTOR

BLOCK

TIP

(+)

GREEN

BLACK

GREEN

Figure 33. Installing an RJ-31X Phone Jack

5. Check the pho nes on the premises for dial tone and the ability to dial out and make phone calls. If phones do not work correctly, check all wiring and correct where necessary. Proceed to the “Troubleshooting” section of this manual if problems persist.

Connecting the Phone Line to the Panel with a DB-8 Cord

After installing the RJ-31X jack, you are ready to connect the phone line to the panel. A DB-8 cord (not included) uses a plug at one end for connecting to the RJ-31X module an d flying leads on the other end for panel terminal connections.

RED

RING

(-)

RED

WHITE (OR YELLOW)

RED

(OR YELLOW)

WHITE

RJ-31X PHONE LINE WIRE RUN

LINES FROM PHONES ON PREMISES

8573G84A.DS

BRN

GRN

Figure 34. Connecting the DB-8 Cord to the Panel and

RJ-31X Jack

RJ-31X

JACK

8573G86A.DSF

GRY

RED

3. Check the pho nes on the premises for dial tone and the ability to dial out and make phone calls. If phones do not work correctly, check all wiring and correct where necessary. Proceed to the “Troubleshooting” section of this manual if problems persist.

Connecting the AC Power Transformer

The panel must be powered by a plug-in stepdown transformer that supplies 24 VAC, 30 VA (60-761) or 24 VAC, 50 VA (60-

778).

For systems that include a Power Line Carrier card and Supervised Wireless Sirens, or X-10 Lamp Modules, the panel must be powered with the Line Carr ier Power Transformer that supplies 24 VAC, 30 VA (60-762) or 24 VAC, 50 VA (60-779).

Connect the power transformer to the panel as shown in Figure

35.

Do not plug in the power transformer at this time. The panel must be powered up using the sequence of steps described in the next section, “Power Up the Panel.”

24 VAC

PANEL TERMINALS

To connect the DB-8 cord to the panel terminals and RJ-31X jack:

1. Connect the green, brown, gra y, and red flying leads from the DB-8 cord to panel terminals 24, 25, 26, and 27 (see Figure 34).

2. Insert the DB-8 cord’s plug into the RJ-31X (see Figure

34).

DRAFT 8/17/00

8573104A.DSF

Figure 35. Connecting a Power Tran sformer to the Panel

Terminals

Page 22

Programming the Panel

Powering Up the Panel

After connecting and wiring all devices to the panel, you are ready to apply AC and backup battery powe r to the panel.

To power up the panel:

1. Connect the red and black battery leads (included with panel) to the lugs located in the upper-left area of the panel circuit board (see Figure 36).

BACKUP BATTERY CONNECTIONS

BLACK RED

BLACK

Figure 36. Connecting the Backup Battery to the Panel

2. Connect the other ends of the battery leads to the battery terminals.

3. Plug the transformer into an outlet that is not controlled by a switch.

RED

BATTERY

8573106A.DSF

(Hardwire Panel Shown—Combination Hardwire/Wireless Panel Similar)

Programming the Panel

For on-site system programming, an alphanumeric touchpad is required.

Entering Program Mode

Entering program mode is done using an installer/dealer code (default = 4321). The system can be put into program mode only when the system is disarmed.

To enter program mode:

1. Make sure the system is disarmed in all partitions.

2. Press

4321

TEM PROGRAMMING.

To enter programming mode using a programming touchpad:

1. Connect the red, black, green, and white wires from the Programming Touchpad Cable (60-791) to the power and bus wires on an alphanumeric touchpad, matching the wire colors on each.

2. Make sure the system is

Note

If the system is powered up touchpad is connected or if a bus command scan is executed, the programming touchpad will be “learned” into the system and must later be manually deleted. See “To delete learned Unit Numbers:” on page 46.

3. Connect the plug on the cable onto the panel programming touchpad header (s ee Figure 37).

+ 0 +

0. The touchpad shows SYS-

powered up and disarmed

after

the program ming

Alphanumeric touchpads display ************, then “Scanning Bus Devices,” and finally a date and time display.

Note

If alphanumeric touchpads don’t display anything, immediately unplug the transformer and disconnect the backup battery. Refer to the “Troubleshooting” section.

4. To permanently mount the transformer, unplug it and remove the existing screw securing the AC outlet cover.

WARNING

Use extreme caution when securing the transformer to a metal outlet co ve r. You could receive a serious shock if a metal outlet cover drops down onto the prongs o f the plug while y ou are securing the transformer and cover to the outlet box.

5. Hold the outlet cover in place and plug the transformer into the lower receptacle.

6. Use the screw supp lied with the transformer to secure the transformer to the outlet cover.

PROGRAMMING TOUCHPAD

Test System Weekly

A41

press both

No Delay

Features

Off

Status

Away

Stay

Pager

Silent

System

Lights

Bypass

CABLE (60-791)

8690G02A.DSF

Figure 37. Connecting a Programming Touchpad

4. Press 8

4321

+ 0 +

2. The touchpad sounds one

short beep. Press ‚ and verify that the display shows SERVICE TOUCHPAD ACTIVE.

5. Press

4321

+ 0 +

0 and the display shows SYS-

TEM PROGRAMMING.

6. After programming is completed, simply disconnect the touchpad from the panel header.

DRAFT 8/17/00

Page 23

Touchpad Button Programming Functions

SECURITY

PHONES

PHONE

OPTIONS

TIMERS

LIGHT

CONTROL

TIER 2

MENUS

8690G 03A .D S F

TOUCHPAD

OPTIONS

REPORTING

SIREN

OPTIONS

SENSORS

AUDIO

VERIFICATION

ACCESSORY

MODULES

ONBOARD

OPTIONS

FROM SECURITY MENU

TO SECURITY MENU

In program mode, touchpad buttons let you navigate to all installer programming menus for configuring the system. Table 6 describes the touchpad button functions in program mode.

Table 6. Alphanumeric Touchpad Button Programming

Functions

Button Programming Function

‚

A & B Scroll through available options at the cur-

0 thru 9 Enter numeric values wherever needed.

1 & 2 Select off (1) or on (2) wherever needed.

1 thru 6 Press and hold to enter alphabetical charac-

7 & 9 Press and hold to enter * (7) or # (9) for

Selects menu item or data entry. Deselects menu item or data entry (if

pressed before #).

rent menu tier. Also scroll th rough sensor text options during sensor text programming.

Enters pauses when programming phone numbers.

Deletes certain programmed settings.

ters A thru F for account numbers.

phone numbers.

Programming the Panel

Figure 39. Tier 2 Program Menus

Again, arrows pointing right represent pressing B to advance forward through the menus. Pressing A moves through the menus in reverse.

Arrows below each menu represent pr essin g

ƒ to advance to

those settings that pertain to that menu. Only when a specific menu is displayed can you advance to those settings. For example, from the SENSORS menu pressing

ƒ gives you access to

learning sensors, programming sensor text, deleting sensors, and viewing/editing sensor programming.

Settings in tier 2 menus can also be accessed by entering shortcut numbers. See the section, “Programming Tier 2 Menu Items” on page 24 for complete details.

Moving Through Program Mode Tiers and Menus

There are two basic tiers of programming menus. Tier 1 menus are accessible immediately after entering program mode (see Figure 38).

TIER 1

MENUS

Programming

TO TIER 2 MENUS

Figure 38. Tier 1 Program Menus

Arrows pointin g right re present pressing B to advance forward through the menus. Pressing A moves through the me nus in reverse.

The arrow below the System Programming menu represents pressing when System Programming is displayed can you advance to tier 2 menus (see Figure 39).

ƒ to advance to tier 2 programming menus. Only

System

FROM TIER 2 MENU

Demo Kit

Off/On

Partition 1

Copy

Clear Memory

Programming

Ready

Exit

8573114A.DSF

DRAFT 8/17/00

Page 24

Programming the Panel

Programming Tier 1 Menu It ems

This section guides you through programming tier 1 menu items as they appear in sequence. Depending on whether you’re installing a new system or changing programming in an existing system will determine the exact order you need to follow. For example, for new installations you should always clear memory before programming any system settings.

Demo Kit Mode

(System Programming)

(Default = off) This setting determines whether the panel is used for a standard installation (off) or as a demo kit (on). When the Demo Kit option is on, only sensors learned into groups 01 and 03, duress code use, and phone test (

8 + sys-

tem master code + 2) will be reported. Turning on this fea-

ture and performing a memor y clear changes the following settings:

Partition 1 Master Code = 1000 Partition 2 Master Code = 2000 User Code 00 = 1001 (partition 1 code—can also be used to

jump to partition 2)

User Code 01 = 1002 (partition 1 code—can also be used to

bypass sensor s)

User Code 02 = 2001 (partition 2 code—can also be used for

remote or off-site access)

User Code 03 = 2002 (partition 2 code—can also be used to

perform system tests)

User Code 04 = 1122 (partition 1 code—can also be used to

jump to partition 2, for remote or offsite access, and system tests)

User Code 05 = 1122 (partition 2 code—can also be used to

jump to partition 1, for remote or offsite access, bypassing sensors, and

system tests) Partition 1 House Code = 255 (P) Partition 2 House Code = 254 (O) Zone 1 (hardwire input 1) = Group 10, Front Door Zone 2 (hardwire input 2) = Group 13, Bedroom Window Zone 3 (hardwire input 3) = Group 17, Living Room Motion

Sensor Zone 4 (hardwire input 4) = Group 1, Panic Zone 5 (wireless, keychain touchpad, ID F00201) = Group 01, (no text) Zone 6 (wireless, DWS, ID A00206) = Group 13, Kitchen Window COMM FAILURE = off Demo Kit = on AVM code = 2121 Entry Delay = 8 sec Exit Delay = 8 sec Extended Delay = 1 minute Siren Timeout = 2 minutes

To turn Demo Kit Mode off or on:

With the display showing DEMO KIT MODE OFF/ON (current setting), press

1 (off) or 2 (on), then press ƒ.

The display flashes the entered setting, then stops after pressing

ƒ and displays DEMO KIT MODE OFF/ON

(new setting).

Partition 1 Copy

(System Programming)

(Default = none) After programming all settings pertaining to partition 1, you can make an exact copy to use for partition 2. This helps reduce programming time when the system is set up for two partitions. If there are certain settings that are unique to partition 2, simply advance to the appropriate menu and make the necessary ch anges.

To Copy Partition 1:

With the display showing PARTITION 1 COPY, press

+ installer code (default = 4321) + ƒ. The display flashes, then stops after pressing

ƒ and

shows DONE.

Clear Memory

(System Programming)

Clearing memory deletes all existing programming information (except the Dealer Code). Clear memory on all newly installed panels before programming.

To Clear Panel Memory:

1. With the system in program mode, pr ess

A or B until

the display shows CLEAR MEMORY.

2. Press

ƒ and the display shows ENTER CODE TO

CLEAR MEMORY.

3. Enter the 4-digit installer code (default = 4321) or dealer code (if progra m m ed ) +

ƒ.

After about five seconds, the system restarts and the panel scans the bus to learn all bus devices.

If the system doesn’t respond as described, repeat step 3.

Programming Tier 2 Menu Items

This section guides you through programming tier 2 menu items as they appear in sequence. Figure 40 shows the menus available on tier 2.

TIER 2

MENUS

SECURITY

TOUCHPAD

OPTIONS

ACCESSORY

MODULES

Each menu on tier 2 represents a group of settings related to the menu name. Some tier 2 menus break down into settings that affect the whole system (global) or a specific partition.

REPORTING

ONBOARD

Figure 40. Tier 2 Program Menus

PHONES

OPTIONS

PHONE

OPTIONS

SIREN

OPTIONS

TO SECURITY MENU

FROM SECURITY MENU

TIMERS

SENSORS

8690G 03A .D S F

LIGHT

CONTROL

AUDIO

VERIFICATION

DRAFT 8/17/00

Page 25

Programming the Panel

Note

Using Shortcut Numbers

To go directly to a setting in tier 2, you can enter the shortcut number for that setting. Shortcut numbers in this manual appear in parenthesis (), under the setting name.

MENU NAME

Downloa d e r Code (0000)

SHORTCUT NUMBER

LOCATION

(Security-Global)

Shortcut numbers can be used from any setting location within tier 2.

To advance to tier 2 program menus:

With the system in program mode and the display showing SYSTEM PROGRAMMING, press ƒ once. The display should show SECURITY.

Security Menu

The SECURITY menu lets you choose wheth er security settings affect the whole system (global) or a specific partition.

To access global or partition security menu items:

1. With the display showing SECURITY, press ƒ. The dis- play should show GLOBAL.

2. Press

ƒ again to advance to global settings, or press A or

B to display PARTITION n , then press ƒ to advance to

selected partition 1 or 2 settings.

The following describes how to program the security settings that appear under GLOBAL .

Installer Code

(Security-Global)

(0001)

(Default = 4321) The 4-digit installe r code is used fo r enteri ng program mode and changing system settings. If a dealer code is programmed, only those settings not associated with phone numbers can be changed.

To program an Installer Code:

With the display showing INSTALLER CODE nnnn (current code), enter the desired 4-digit code. The

display flashes the entered code. Press

ƒ and the display

shows the new code.

The Installer Code ca nno t b e d ele ted or cleared from panel memory. To change the Installer Code to its default setting, enter 4321 in the procedure above.

Dealer Code

(Security-Global)

(0002)

(Default = none) The 4-digit dealer code is used to prevent unauthorized persons from changing the programmed central station phone numbers. When this feature is enabled, central station phone numbers cannot be changed (unless you enter the program mode by us ing the deal er code). All other system settings are still accessible by entering the program mode with the installer code.

To program a Dealer Code:

With the display showing DEALER CODE

✱✱✱✱, enter

the desired 4-digit code. The display flashes the entered code. Press

ƒ and the display shows the new code.

To delete a Dealer Code:

With the display showing DEALER CODE nnnn (current code), press

✱✱✱✱.

D. The display shows DEALER CODE

Downloader Code

(Security-Global)

(0000)

(Default = 12345) The 5-digit downloader code is used in conjunction with downl o ad er pr og ra m mi n g. Th e downl o ad e r operator must have t he pa nel ac count num ber and do wnlo ader code in order to perform any programming.

To program a Downloader Code:

With the display showing DOWNLOADER CODE nnnnn (current code), enter the desired 5-digit code. The

display flashes the entered code. Press

ƒ and the display

shows the new code.

Note

The Downloader Code cannot be deleted or cleared from panel memory. T o change the Down loader Code to its default setting, enter 12345 in the procedure above.

DRAFT 8/17/00

The Dealer Code c annot be dele ted by c learing panel memory.

The following sections describe the security settings that appear under PARTITI ON 1 and PARTITON 2.

Account Number

(Security—Partition 1-2)

(partition 1: 0010, partition 2: 0020)

(Defaults = 00000) The account number is used as p anel (or customer) identification for the central monitoring station. The panel sends the account number every time it repo rts to the central station. Account numbers must be 1 to 10 characters long.

Alpha characters A–F can be assigned to the account number by pressing and holding buttons 1–6 respectively, until the character appears.

To program an Account Number:

With the display showing ACCOUNT NUMBER nnnnn (current number), enter the desired account number.

The display flashes the entered number. Press

ƒ and the

display shows the new number.

Page 26

Programming the Panel

Quick Arm

(Security—Partition 1-2)

(partition 1: 0011, partition 2: 0021)

(Defaults = off) Quick Arm allows system arming without using an access code. When Quick Arm is on, the system arming level can be increased from Level 1-OFF to LEVEL 2STAY, from Level 1-OFF to LEVEL 3-AWAY, or from Level 2-STAY to LEVEL 3-AWAY, without entering an access code.

A valid access code is still required to decrease the arming level or disarm the system.

To turn Quick Arm off or on:

With the display showing QUICK ARM OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Quick Exit

(Security—Partition 1-2)

(partition 1: 0012, partition 2: 0022)

(Defaults = on) This setting determines whether or not users can open and close a standard entry/exit door without causing an alarm (while the system is armed).

This feature would be useful if the user wants to go out to get the morning paper while the system is armed. This feature also allows the user to leave the armed premises without having to disarm and re-arm the system.

When Quick Exit is on, pressing

D on a touchpad (while the

system is armed) starts a 2-minute timer that allows one standard entry/exi t d oor (sensor groups 1 0 a n d 19 only) to be acti vated once (opened, then closed).

When this feature is turned off, the system must be disarmed before any protected door is opened.

Note

For UL Listed inst allation s, this f eature must be set to off.

To turn Quick Exit off or on:

With the display showing QUICK EXIT OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Exit Extension

(Security—Partition 1-2)

(partition 1: 0013, partition 2: 0023

(Defaults = on) This setting determines whether or not the user can re-enter and exit again through an entry or exit delay door (without disarming and re-arming the system). This helps prevent exit faults and false alarms by allowing users to re-enter the premises for a forgotten item.

When Exit Extension is on, the panel restarts the exit delay timer if the user re-enters the premises through a standard delay door before th e standard exit delay tim e e xpires.

When this feature is off, the exit delay timer does not restart if the user re-enters the premises, forcing the user to disarm the system to avoid setting off an accidental alarm.

To turn Exit Extension off or on:

With the display showing EXIT EXTENSION OFF/ON (current setting), press

flashes the entered setting. Press

1 (off) or 2 (on). The display

ƒ and the display

shows the new setting.

Auto Stay Arming

(Security—Partition 1-2)

(partition 1: 0014, partition 2: 0024)

(Defaults = on) This setting determines whether or not the system automatically arms to STAY (level 2) if the user arms the system to AWAY (level 3) without exiting the premises. This can help prevent accidental alarms by deactivating interior motion sensors during occupied arming periods.

When this feature is on and the system is armed to AWAY, touchpads (and other status sounders) emit one exit delay beep every four seconds, then one every second during the last 10 seconds. If the exit delay time expires with no standard delay sensor activation, the system automatically arms to STAY.

Note

Arming the system to “AWAY with No Delay” overrides the Auto Stay Arming feature.

To turn Auto Stay Arming off or on:

With the display showing AUTO STAY ARMING OFF/ ON (current setting), press

1 (off) or 2 (on). The

display flashes the entered setting. Press ƒ and the display shows the new setting.

Keyswitch Sensor

(Security—Partition 1-2)

(partition 1: 0015, partition 2: 0025)

(Defaults= none) This featur e lets users arm and disarm the system using either a keyswitch wired to a hard wire zone input or a wireless door/window sensor.

For example, if sensor 1 is designated as the keyswitch sensor and the system is disarmed, then tripping sensor 1 could arm the system to AWAY. If the system is armed to STAY or AWAY, then tripping the sensor could disarm the system (depending on keys wi t c h style).

The panel reports ope ni ng, closing, and force ar med reports (if turned on) to the central monitoring station.

Note

A bypassed keyswitch sensor cannot arm or disarm the system.

During an audible alarm, keyswit ch se nso rs can disarm the system (which sends a cancel report to the central monitoring station), but cannot arm the system. The system can be armed only after the siren timeout expi res.

Keyswitch sensors test the same as any other sensor and do not arm or disa rm the sys tem du ring a se nsor test.

To assign a Keyswitch Sensor:

With the display showing KEYSWITCH SENSOR nn (current sensor number), enter th e desired sensor

number (01–76). The display flashes the entered sensor number . Pres s

ƒ and the display shows the new number.

To delete a Keyswitch Sensor:

With the display showing KEYSWITCH SENSOR nn (current sensor number), press

D to erase the keyswitch

sensor attribute.

DRAFT 8/17/00

Page 27

Programming the Panel

Note

Keyswitch Style

(Security—Partition 1-2)

(partition 1: 0016, partition 2: 0026)

(Defaults = transition) This feature allows users to select how they want the system to behave when armed/disarmed by a keyswitch sensor. The choices are as follows:

Transition: If keyswitch style is set to transition and the keyswitch sensor is tripped (opened) when the system is disarmed (level 1), the panel will automatically arm to AWAY (level 3). If the sensor is tripped (opened) when the system is armed to AWAY (level 3) or STAY (level 2) , the panel will automatically disarm.

State: If keyswitch style is set to state, when the keyswitch sensor is tripped (opened) the panel arms to AWAY (l evel 3). If the sensor is restored (closed) the panel disarms.

Opening, closing, and force arming repor t s (if turned on) are reported to the central station for both keyswitch styles.

To assign a Keyswitch Style:

With the display showing KEYSWITCH STYLE TRANSITION/STATE (current setting), press

set the type to Transition. Press

2 + ƒ to set the type to

1 + ƒ to

State.

Duress Code

(Security—Partition 1-2)

(partition 1: 0017, partition 2: 0027)

(Defaults = none) The duress code is a unique 4-digit access code that allows users to operate the system and, at the same time, instructs the panel to send a silent alarm report to the central station.

Do not use a duress code unless it is absolutely necessary. Using duress codes often results in false alarms due to code entry errors. If a duress code is absolutely necessary, use it with an audio verification module (AVM) to reduce false alarms and accidental dispatches.

Note

To use this feature, the under the must be turned on.

REPORTING—PARTITION 1 (2)

DURESS OPTION

setting

To program a Duress Code:

With the display showing DURESS CODE

✱✱✱✱, enter

the desired 4-digit duress code. The display flashes the entered setting. Press ƒ and the display shows the new code.

Phones Menu

The PHONES menu lets you set up central station reporting for the system.

The following describes how to program the settings that appear under CS PHONE 1-3.

Phone Number

(Phones—CS Phone 1-3)

(cs phone 1: 0100, cs phone 2: 0110, cs phone 3:

0120)

(Defaults = none) This setting is used for programming the central station receiver phone number. Phone numbers can be 1 to 24 digits long, including pauses or * and # characters.

To enter pauses, press

To enter *, press and hold 7 for about two seconds. To enter #, press and hold 9 for about two seconds.

The

PHONE NUMBER

Dealer Code is programmed and the Installer Code is used to enter installer programming mode. To access these menus when a Dealer Code is programmed, you must e nter in stall er prog ram ming m ode us ing t he Dealer Code.

Call-waiting services should be disabled to prevent interrupting panel communication to the central monitoring station. To program a dialing prefix that disables call-waiting, see the setting under the menu

BAL.

menus are not accessible if a

CALL WAIT CANCEL

PHONE OPTIONS—GLO-

To program a Central Station Phone Number:

With the display showing PHONE NUMBER _ (or current number), enter the desired phone number. The

display flashes the entered number. Press

ƒ and the

display shows the new number.

To delete a Central Station Phone Number:

With the display showing PHONE NUMBER (current number), press

The display shows PHONE NUMBER _.

To delete a Duress Code:

With the display showing DURESS CODE nnnn (current code), press

✱✱✱✱.

DRAFT 8/17/00

D. The display shows DURESS CODE

Page 28

Programming the Panel

High Level Rpts

(Phones—CS Phone 1-3)

(cs phone 1: 0101, cs phone 2: 0111, cs phone 3:

0121)

(Defaults: CS Phone 1 = on, CS Phone 2 and 3 = off) When this setting is on, the following conditions report to the central station:

❑ Fire, Police, Auxiliary, and Duress alarms ❑ No Activity ❑ Receiver Failure (or jam) ❑ T amper conditions, including Zone T ampers and System

Tamper (40 incorrect key presses or touchpad supervisory)

❑ Entering or exiting Sensor Test mode ❑ Phone Test

To turn High-Level Reports off or on:

With the display showing HIGH LEVEL RPTS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Low Level Rpts

(Phones—CS Phone 1-3)

(cs phone 1: 0102, cs phone 2: 0112, cs phone 3:

0122)

(Defaults: CS Phone 1 = on, CS Phone 2 and 3 = off) When this setting is on, the following non-alarm conditions report to the central station:

❑ Force Armed ❑ Hardwire Zone Trouble (open or short) ❑ Supervisory (wireless devices) ❑ Low Battery (wireless devices) ❑ Phone Test ❑ Other non-alarm related conditions

To turn Low-Level Reports off or on:

With the display showing LOW LEVEL RPTS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Exception Rpts

(Phones—CS Phone 1-3)

(cs phone 1: 0103, cs phone 2: 0113, cs phone 3:

0123)

(Defaults = off) When this setting is on, the panel reports to the central station if the system is not armed or disarmed at the specified schedule times.

To turn Exception Reports off or on:

With the display showing EXCE P T IO N RP TS OF F / ON (current setting), press

flashes the entered setting. Press

1 (off) or 2 (on). The display

ƒ and the display

shows the new setting.

Open/Close Rpts

(Phones—CS Phone 1-3)

(cs phone 1: 0104, cs phone 2: 0114, cs phone 3:

0124)

(Defaults = off) This setting determines whether opening and closing reports are sent to the central station. When turned on, the panel sends a closing report when the system is armed and an opening report when the system is disarmed.

Note

To use this feature, the

CLOSING REPORTS ING

menu must be turned on for that partition.

OPENING REPORTS

settings under the

and

REPORT-

To turn Opening/Closing Reports off or on:

With the display showing OPEN/CLOSE RPTS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Backup

(Phones—CS Phone 1-3)

(cs phone 1: 0105, cs phone 2: 0115, cs phone 3: 0125)

(Defaults: CS Phone 1 = on, CS Phone 2 and 3 = off) This setting determines whether or not the panel uses another programmed central station phone number for reporting if attempts with the first number are unsuccessful.

When BACK UP is off, the panel will make up to eight attempts to deliver a report with the programmed phone number.

When BACK UP is set to ON, the panel makes up to 16 attempts to deliver the report, alternating between the programmed phone numb er and the backup phone number.

CS PHONE 1 is backed up by CS PHONE 2. CS PHONE 2 is backed up by CS PHONE 1. CS PHONE 3 is backed up by CS PHONE 1.

To turn Backup off or on:

With the display showing BACK UP OFF/ON (current setting), press

1 (off) or 2 (on). The display flashe s th e

entered setting. Press ƒ and the display shows the new setting.

SIA/CID Reporting

(Phones—CS Phone 1-3)

(cs phone 1: 0106, cs phone 2: 0116, cs phone 3: 0126)

(Defaults = CID) This setting determines whether the panel uses the SIA or CID (Contact ID) reporting format for central station communication.

To select SIA or CID reporting:

With the display showing REPORTING FORMAT SIA/ CID (current setting), press

1 (for SIA) or 2 (for CID).

The display flashes the entered setting. Press ƒ and the display shows the new setting.

DRAFT 8/17/00

Page 29

Programming the Panel

Note

The following describes how to program the phone settings that appear under PAGER PHONE 1 through 5.

Phone Number

(Phones—Pager Phone 1-5)

(pager 1: 0130, pager 2: 0140, pager 3: 0150, pager 4: 0160, pager 5: 0170)

(Defaults = none) This setting is used for programming a phone number that communicate s to a pager. Phone numbers can be 1 to 24 digits long and include pauses, a skylink number, and 7-digit PIN number.

To enter pauses, press

To enter *, press and hold 7 for about two seconds. To enter #, press and hold 9 for about two seconds.

Note

Call-waiting services should be disabled to prevent interrupting panel communication to the pager(s). To program a dialing pr efix that disab les call-w aiting, see the

CALL WAIT CANCEL

PHONE OPTIONS—GLOBAL.

setting under the menu

To program a Pager Phone Number:

With the display showing PHONE NUMBER _ (or current number), enter the desired pager phone number.

The display flashes the entered number. Press

ƒ and the

display shows the new setting.

To delete a Pager Phone Number:

With the display showing PHONE NUMBER (current number), press

D. The display shows PHONE NUMBER

Low Level Rpts

(Phones—Pager Phone 1-5)

(pager 1: 0132, pager 2: 0142, pager 3: 0152, pager 4: 0162, pager 5: 0172)

(Defaults = off) This setting determines whether the following non-alarm conditions report to a pager:

❑ Force Armed ❑ Hardwire Zone Trouble (open or short) ❑ Supervisory (wireless devices) ❑ Low Battery (wireless devices) ❑ Phone Test ❑ Other non-alarm related conditions

To turn Low-Level Reports off or on:

With the display showing LOW LEVEL RPTS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Exception Rpts

(Phones—Pager Phone 1-5)

(pager 1: 0133, pager 2: 0143, pager 3: 0153, pager 4: 0163, pager 5: 0173)

(Defaults = off) This setting determines whether the panel reports to a pager if the system is not armed or disarmed at the specified schedule times, if open/close reports are turned on.

To turn Exception Reports off or on:

With the display showing EXCEPTION RPTS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

High Level Rpts

(Phones—Pager Phone 1-5)

(pager 1: 0131, pager 2: 0141, pager 3: 0151, pager 4: 0161, pager 5: 0171)

(Defaults = on) This setting determines whether the following alarm conditions report to a pager:

❑ Fire, Police, Auxiliary, and Duress alarms ❑ No Activity ❑ Receiver Failure (or jam) ❑ T amper conditions, including Zone T ampers and System

Tamper (40 incorrect key presses or touchpad su pervisory)

❑ Entering or exiting Sensor Test mode ❑ Phone Test

To turn High-Level Reports off or on:

With the display showing HIGH LEVEL RPTS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Open/Close Rpts

(Phones—Pager Phone 1-5)

(pager 1: 0134, pager 2: 0144, pager 3: 0154, pager 4: 0164, pager 5: 0174)

(Defaults = off) This setting determines whether opening and closing reports are sent to a pager. When turned on, the panel sends a closing report when the system is armed and an opening report when the system is disarmed.

To use this feature, the

CLOSING REPORTS ING

menu must be turned on for that partition.

OPENING REPORTS

settings under the

and

REPORT-

To turn Opening/Closing Reports off or on:

With the display showing OPEN/CLOSE RPTS OFF/ON (current setting), press

flashes the entered setting. Press

1 (off) or 2 (on). The display

ƒ and the display

shows the new setting.

DRAFT 8/17/00

Page 30

Programming the Panel

Latchkey Reports

(Phones—Pager Phone 1-5)

(pager 1: 0135, pager 2: 0145, pager 3: 0155, pager 4: 0165, pager 5: 0175)

(Defaults = on) This setting determines whether the panel reports to a pager when the system is armed or disarmed, according to latchkey time scheduling.

To turn Latchkey reports off or on:

With the display showing LATCHKEY RPTS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Streamlining

(Phones—Pager Phone 1-5)

(pager 1: 0136, pager 2: 0146, pager 3: 0156, pager 4: 0166, pager 5: 0176)

(Defaults = on) This setting determines whether the panel includes (off) or excludes (on) the account n um ber when reporting to a pager.

To turn Streamlining off or on:

With the display showing STREAMLINING OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Ptn Assignment

(Phones—Pager Phone 1-5)

(pager 1: 0137, pager 2: 0147, pager 3: 0157, pager 4: 0167, pager 5: 0177)

(Defaults = 1) This setting determines the partition that reports to a pager. Both partitions can be assigned to report to a single pager.

To set up Partition Assignments for pager reporting:

With the display showing PTN ASSIGNMENT 1/2/12 (current setting), press

1 or 2 to select partition 1 or 2

(press 1 and 2 to select both partition 1 and 2). The display flashes the entered setting. Press ƒ and the display shows the new setting.

The following describes how to program the phone settings that appear under DOWNLOADER PHONE.

Phone Number

(Phones—Downloader Phone)

(0180)

(Default = none) Use this setting to enter the phone number of an off-site computer that can be used to program the panel through the phone line. Phone numbers can be 1 to 24 digits long, including pauses or * and # character s.

To enter pauses, press

To enter *, press and hold 7 for about two seconds. To enter #, press and hold

Note

Call-waiting services should be disabled to prevent interrupting panel communication to the downloader. To program a dialing prefix that disables call-waiting, see the

PHONE OPTIONS—GLOBAL.

CALL WAIT CANCEL

9 for about two seconds.

setting under the men u

To program a downloader phone number:

With the display showing PHONE NUMBER (current number), enter the desired phone number. The display

flashes the entered number. Press

ƒ and the display

shows the new setting.

To delete a downloader phone number:

With the display showing PHONE NUMBER (current number), press

D to erase the number. The display

shows PHONE NU M B ER _.

Phone Options Menu

The PHONE OPTIONS menu lets you set up system phone access and communications that affect the whole system (global) or a specific partition.

The following describe how to program the phone option settings that appear under GLOBAL.

Phone Test

(Phone Options—Global)

(02000)

(Default = on) This setting determines if the user can, at any time, test the communication from the panel to the central station or a pager by enteri ng 8 + CODE + 2 (# + 8 + CODE + 2 from a touch-tone ph on e).

To turn the Phone Test setting off or on:

With the display showing PHONE TEST OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

DRAFT 8/17/00

Page 31

Programming the Panel

Note

Auto Phone Test

(Phone Options—Global)

(02001)

(Default = off) This setting determines if the panel sends a phone test automatically to the central station or a pager on a predetermined schedule. (Refer to the “Phone Test Freq.” and “Next Phone Test” settings found under TIMERS—GLOBAL).

Note

For U.L. Commercial Listed installations (UL 1610), this feature must be on.

To turn Automatic Phone Test off or on:

With the display showing AUTO PHONE TEST OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Auto Test Reset

(Phone Options—Global)

(02002)

(Default = on) This setting determines whether or not the Auto Phone Test interval is reset after any successful report to the central monitoring station. (Refer to the “Phone Test Freq.” and “Next Phone Test” settings found under TIMERS— GLOBAL).

When this feature is on, the panel considers any successful report to the central monitoring station to be a successful phone test. Thus, any panel report resets the Next Phone Test setting to the Phone Test Freq. value. The panel only conducts an Auto Phone Test if no other reports have been mad e dur ing the Phone Test Freq. time period.

When this feature is off, an Auto Phone Test is always conducted according to the schedule of the Phone Test Freq. setting, even if the panel makes other reports to the central monitoring station during that time period.

Note

PHONE TEST FREQ must be set to 2 or higher for this feature to work.

To turn Auto Test Reset off or on:

With the display showing AUTO TEST RESET OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Comm Failure

(Phone Options—Global)

(02003)

(Default = on) This setting determines whether the panel activates trouble beeps to alert users on the premises that communication to the central station failed. Failure notification occurs after the third unsuccessful reporting attempt to the central station/pager.

If a Phone Supervision Card (60-789) is installed, failure notification can occur immediately if inadequate ph one line voltage is detected upon the initial dialing attempt.

For UL Listed installations, Comm Failure must be turned on.

To turn Communication Failure notification off or on:

With the display showing COMM FAILURE OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

DTMF Dialing

(Phone Options—Global)

(02004)

(Default = on) This setting determines whether the panel uses DTMF tones (on) or pulse (off) for dialing programmed phone numbers.

To turn DTMF Dialing off or on:

With the display showing DTMF DIALING OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Dialer Abort

(Phone Options—Global)

(02005)

(Default = on) This setting determines whether or not the user can stop a panel before it sends a false alarm to the central station.

When this feature is on, alarm reports from sensors in groups 00–20, 34, and 35 can be aborted. To abort the dialing attempt, the user must enter

1 + user code within the Dialer

Abort Delay time setting (defaulted to 30s). Cancel and restoral reports from these sensor groups are aborted at the same time. The following reports can also be aborted.

❑ System Alarm Tamper/Cancel ❑ No Activity Alarm/Cancel ❑ Touchpad Police and Auxiliary Panic/Cancel ❑ Recent Closing and Two Trip Error

DRAFT 8/17/00

Fire alarm reports to the central station cannot be aborted.

To turn Dialer Abort off or on:

With the display showing DIALER ABORT OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Page 32

Programming the Panel

Dial Abort Delay

(Phone Options—Global)

(02006)

(Default = 30 sec) This setting determines how much time the user has to abort a panel report.

To change the Dial Abort Delay:

With the display showing DI AL ABORT D ELA Y n n SECS (current setting), enter the desired time (15–120s). The

display flashes the entered setting. Press

ƒ and the

display shows the new setting.

Cancel Message

(Phone Options—Global)

(02007)

(Default = on) This setting determines whether or not the panel displays a cancel message after the user disarms the system to clear an alarm condition.

To turn Cancel Message off or on:

With the display showing C AN CEL ME SS AGE OF F/O N (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Pager Delay

(Phone Options—Global)

(02008)

(Default = 15 sec) This setting determines how long a report is delayed to a pager, after the panel dials the pager number.

Note

The Pager Delay time should not be set below 5 seconds, unless absolutel y nec es sary.

To set the Pager Delay time:

With the display showing PAGER DELAY nn SECS (current setting), enter a delay time (0 –30). The display

flashes the entered setting. Press

ƒ and the display

shows the new setting.

Call Wait Cancel

(Phone Options—Global)

(02009)

(Default = none) This feature lets you set up a dialing prefix to disable the call waiting feature before the panel makes its first dialing attempt to any programmed central monitoring station or downloader phone number. The prefix can be up to eight digits.

To enter pauses, press To enter *, press and hold To enter #, press and hold

7 for one second. 9 for one second.

Dial Tone Detect

(Phone Options—Global)

(02010)

(Default = on) When this setting is on, the panel does not begin dialing until it detects a dial tone.

When this feature is off, the panel begins dialing a few seconds after seizing the phone line.

To set up Dial Tone Detect:

With the display showing DIAL TONE DETECT OFF/ ON (current setting), press

display flashes the entered setting. Press

1 (off) or 2 (on). The

ƒ and the

display shows the new setting.

The following sections describe the phone option settings that appear under PARTITION 1-2.

Note

A Phone Interface/Voice module must be installed for the system to use the settings under

OPTIONS—PARTITION 1 and PARTITION 2.

Local Phone Control

(Phone Options—Partition 1-2)

PHONE

(partition 1: 0210, partition 2: 0220)

(Defaults = on) When this feature is on, the panel can be accessed from a phone on the premises.

To set up Local Phone Control:

With the display showing LOCAL PHONE CTRL OFF/ ON (current setting), press

1 (off) or 2 (on). The

display flashes the entered setting. Press ƒ and the display shows the new setting.

Remote Access

(Phone Options—Partition 1-2)

(partition 1: 0211, partition 2: 0221)

(Defaults = on) When this setting is on, the panel can be accessed from an off-site phone.

To turn Remote Access off or on:

With the display showing REMOTE ACCESS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

To set up Call Wait Cancel:

With the display showing CALL WAIT CANCEL __ (or current setting), enter the desired prefix. The display

flashes the entered setting. Press

ƒ and the display

shows the new setting.

To delete the Call Wait Cancel prefix:

With the display showing CALL WAIT CANCEL __ (or current setting), press

DRAFT 8/17/00

Page 33

Programming the Panel

Note

Ring/Hang/Ring

(Phone Options—Partition 1-2)

(partition 1: 0212, partition 2: 0222)

(Defaults = on) This setting determines how the panel picks up (seizes) the phone line. Select “on” if an answering machine shares the phone line with the panel. Select “off” if there is no answering machine sharing the phone line with the panel.

Note

The REMOTE A CCESS setting must be turned on for this feature to work.

When this feature is on, the person who is calling the panel must use the following procedur e:

1. Listen for one or two full rings.

2. Hang up.

3. Call the premises again within the next 10–40 seconds. The system answers after the first ring.

When this feature is off, the system answers after 12 full rings.

To turn Ring/Hang/Ring access off or on:

With the display showing RING/HANG/RING OFF/ON (current setting), press

begins flashing the entered selection. Press

1 (off) or 2 (on). The display

ƒ and the

display shows the new setting.

Line Fail Delay

(Phone Options—Partition 1 only)

(partition 1: 0213)

(Default = none) This setting determines the amount of time the partition 1 phone line voltage must be absent before the panel indicates a phone failure trouble condition. If a delay is not programmed (default), the panel will not monitor the phone line voltage.

Note

LINE FAIL DELAY

this time.

Note

A Phone Supervision Card must be installed to use this feature.

is not available for partition 2 at

To set the Line Fail Delay time:

1. With partition 1 selected, press

A or B until the display

shows LINE FAIL DELAY nn SECS (current setting).

2. Enter the desired tim e value (10–240 seconds). T he dis-

play flashes the entered setting. Press

ƒ and the display

shows the new setting.

To delete the Line Fail Delay time:

1. With partition 1 selected, press

A or B until the display

shows LINE FAIL DELAY nn SECS (current setting).

2. Press

D to delete the current line fail delay time.

Toll Saver

(Phone Options—Partition 1-2)

(partition 1: 0214, partition 2: 0224)

(Defaults = on) This setting determines whether the panel answers a phone call on the eighth ring (on) or twelfth ring (off) when a trouble condition exists.

To turn Toll Saver off or on:

1. With the desired partition selected, press

A or B until the

display shows TOLL SAVER OFF/ON (current setting).

2. Press

Phone Panic

1 (off) or 2 (on). The display flashes the entered

setting. Press

ƒ and the display shows the new setting.

(Phone Options—Partition 1-2)

(partition 1: 0215, partition 2: 0225)

(Defaults = off) This setting determines whether or not a police panic alarm can be activated from a tou ch-tone phone. When this feature is on, pressing

ƒ + ‚‚‚‚‚‚ from a

touch-tone phone on the premises causes a panic alarm.

To turn Phone Panic off or on:

1. With the desired partition selected, press

A or B until the

display shows PHONE PANIC OFF/ON (current setting).

2. Press

1 (off) or 2 (on). The display flashes the entered

setting. Press ƒ and the display shows the new setting.

Phone Access Key

(Phone Options—Partition 1-2)

(partition 1: 0216, partition 2: 0226)

(Defaults =

) This setting determines which touch-tone

phone button is used for system access and control. If the Local Phone Control feature is enabled, the user can

pick up the phone and press # (within 5 seconds) to access the security system. The panel seizes the phone line and waits for the user to enter system commands. Phone access can be changed from # to * (see the following note).

Use the default setting (#) to avoid conflicts between the security system and other phone devices and services. Many phone devices (such as answering machines, computer modems, and FAX machines) and services (such as call-waiting, call-forwarding, and some banking transactions) require * to initiate their operation, so using * for this security feature could cause conflicts.

To change the Phone Access Key:

1. With the desired partition selected, press

A or B until the

display shows PHONE ACCESS KEY #/* (current setting).

2. Press

(for *) or

2 (for #). The display flashes the

entered setting. Press ƒ and the display shows the new setting.

DRAFT 8/17/00

Page 34

Programming the Panel

Timers Menu

The TIMERS menu lets you set up the various system feature times that affect the whole system (global) or a specific partition.

The following describes how to program the timer settings that appear under GLOBAL.

Supervisory Time

(Timers—Global)

(0300)

(Default is set randomly between 01:00 and 04 : 00) This setting determines what time of day the panel sends supervisory, low battery, or auto phone test reports to the central station.

Note

The panel clock must be set with the correct time for accurate supervisory time reporting. See “Time and Date Menu” on page 50.

To set the Supervisory Time:

With the display showing SUPERVISORY TIME HH:MM (current setting), enter the desired 4-digit time

value. For example, enter 0330 to set the supervisory time for 3:30

. The display flashes the entered setting.

A.M

Press ƒ and the display shows the new setting.

Phone Test Freq.

(Timers—Global)

(0302)

(Default = 7 days) This setting determines how often the panel conducts the automatic phone test (see “Auto Phone Test” under “Phone Options—Global”). The system can be set to perform an automatic phone test anywhere from every day to every 255 days.

Note

For U.L. Commercial Listed installations (UL 1610), this feature must be set to 1.

To set the Phone Test Freq:

With the display showing PHONE TEST FREQ nnn DAYS (current setting), enter the number of days

(1–255). The display flashes the entered setting. Press

and the display shows the new setting.

Next Phone Test

(Timers—Global)

(0303)

(Default = 7 days) This setting is used by the Auto Phone Test feature (see “Phone Options - Global”) to determine when the next automatic phone test should occur. This setting should be the same, or less than, the Phone Test Freq. setting.

Note

For U.L. Commercial Listed installations (UL 1610), this feature must be set to 1.

RF Tx Timeout

(Timers—Global)

(0301)

(Default = 12 hours) This setting determines how many hours (2–24) the panel has to receive at least one signal from a wireless sensor (le ar ned i nto a s uperv ise d gr oup) . If the panel do es not receive a signal from any supervised wireless sensor within the set time, the panel reports a supervisory condition to the central station.

Note

For U.L. Listed commercial installations, the RF Tx Timeout must be set to 4 hours. For U.L. Listed residential installations , the RF Tx Timeo ut must be s et to 24 hours.

To set the RF Tx Timeout:

With the display showing RF TX TIMEOUT nn HOURS (current setting), enter the desired timeout value (2–24).

The display flashes the entered setting. Press

ƒ and the

display shows the new setting.

To set the Next Phone Test:

With the display showing NEXT PHONE TEST nnn DAYS (current setting), enter the number of days

(1–255). The display flashes the entered setting. Press

and the display shows the new setting.

Output Trip Time

(Timers—Global)

(0304)

(Default = 4 sec) This setting determines how long outputs are activated when tripped (if they are configu red for a momentary response).

To set the Output Trip Time:

With the display showing OUTPUT TRIP TIME nn SECS (current setting), enter the number of seconds (1–12).

The display flashes the entered setting. Press

ƒ and the

display shows the new setting.

Activity Timeout

(Timers—Global)

(0305)

(Default = 24 hours) This setting determines when the system sends a “no activity” report. The panel can be set to wait from 1 - 42 hours. If no user interacti o n o r de vic e ac t iv a t ion oc c ur s in that time, the panel sends a report to the central station.

To set the Activity Timeout:

With the display showing ACTIVITY TIMEOUT nn HOURS (current setting), enter the number of hours (1–

42). The display flashes the entered setting. Press

ƒ and

the display shows the new setting.

DRAFT 8/17/00

Page 35

Programming the Panel

Note

Daylight Saving

(Timers—Global)

(0306)

(Default = on) When this setting is on, the panel clock automatically adjusts for daylight saving time changes.

To turn Daylight Saving off or on:

With the display showing DAYLIGHT SAVING OFF/ON (current setting), press

flashes the entered setting. Press

1 (off) or 2 (on). The display

ƒ and the display

shows the new setting.

The following sections describe the timer settings that appear under PARTITION 1-2.

Entry Delay

(Timers—Partition 1-2)

(partition 1: 0310, partition 2: 0320)

(Defaults = 32 sec) This setting determines how much time the user has to disarm the system (after entering the armed premises through a “designated delay door”) without causing an alarm.

Note

For residential UL Listed installations, the Entry Delay must be set to 45 seconds or less.

To set the Entry Delay:

With the display showing ENTRY DELAY nnn SECS (current setting), enter the desired time value

(32–240 using 8-second intervals). The display flashes the entered setting. Press

ƒ and the display shows the

new setting.

Extended Delay

(Timers—Partition 1-2)

(partition 1: 0312, partition 2: 0322)

(Defaults = 4 minutes) This setting determines how much time the user has (after arming the system) to enter or exit the premises through a “designated extended delay door” (1–8 minutes).

For UL Listed installations Extended Delay may not be used.

To set the Extended Delay:

With the display showing EXTENDED DELAY n MINUTES (current setting), enter the desired time valu e

(1–8). The display flashes the entered setting. Press

and the display shows the new setting.

Siren Timeout

(Timers—Partition 1-2)

(partition 1: 0313, partition 2: 0323)

(Defaults = 4 minutes) This setting determines how long sirens sound (1–30 minutes) if no one is present to disarm the system.

For UL Listed installations, the Siren Timeout must be set to 4 minutes or more.

To set the Siren Timeout:

With the display showing SIREN TIMEOUT nn MINUTES (current setting), enter the desired time valu e

(1–30). The display flashes the entered setting. Press

and the display show the new setting.

Exit Delay

(Timers—Partition 1-2)

(partition 1: 0311, partition 2: 0321)

(Defaults = 64 sec) This setting determines how much time the user has (after arming the system) to leave the premises through a “designated delay door” without causing an alarm.

Note

For residential UL Listed installations, the Exit Delay must be set to 60 seconds or less.

To set the Exit Delay:

With the display showing EXIT DELAY nnn SECS (current setting), enter the desired time value (48–184

using 8-second intervals). The display flashes the entered setting. Press

ƒ and the display shows the new

setting.

DRAFT 8/17/00

Page 36

Programming the Panel

Light Control Menu

The LIGHT CONTROL menu lets you set up light activation for a specific partition.

The following describes how to program the light control settings that appear under PA RTITION 1 and PARTITION 2.

Note

For light con trol to w ork, X-10 Powerhous e Lamp Modules must be installed at desired lamps.

Entry Lights

(Light Control—Partition 1-2)

(partition 1: 0400, partition 2: 0410)

(Defaults = none) This setting determines which X-10 controlled lights turn on during entry and exit delays.

Note

X-10 Lamp Modules set to 1 always turn on during the entry and exit delays.

Note

X-10 Lamp Modules set to 2 always flash the arming level when arming the system. For example, lights flash two times when arming to STAY (level 2), and three times when arming to AWAY (level 3).

To set the Entry Lights:

1. With the desired partition selected, press

ƒ. The display

shows ENTRY LIGHTS nnnnnnn (current setting).

2. Enter all the desired light numbers (3–9 based on the UNIT dial setting on each X-10 Lamp Module). The display flashes the entered setting(s). Press

ƒ and the dis-

play shows the new setting(s).

Touchpad Options Menu

The TOUCHPAD OPTIONS menu lets you set up touchpad panic and arming operation.

The following section describes the touchpad option settings that appear under GLOBAL.

Latchkey Zones

(Touchpad Options—Global)

(0500)

(Default = none) This setting defines the range of keychain touchpads that will function as a latchkey user. The value entered in this section can be any valid zone number. When a zone number is entered, all zones at or below that zone number will function as a latchkey user. For example, if 5 is entered, any keychain touchpads learned into zones 1–5 will be latchkey users and all others (6–76) will not.

To set the number of Latchkey Zones:

1. With the display showing LATCHKEY ZONES nnn (current setting), enter the desired number of latchkey zones

(00–76). The display flashes the entered setting.

2. Press

ƒ and the display shows the new setting.

To delete/disable Latchkey Zones:

1. With the display showing LATCHKEY ZONES nnn (current setting), press

The following sections describe the touchpad option settings that appear under PARTITION 1-2.

To delete Entry Lights:

Enter any light number that appears on the display, then

ƒ. The number disappears from the display.

press

House Code

(Light Control—Partition 1, 2)

(partition 1: 0401, partition 2: 0411)

(Defaults: partition 1 = 01-B; partition 2 = 02-C) This setting enables X-10 controlled lights to work in a selected partition without interfering with the X-10 controlled lights of the other partition.

After setting the panel house code for each partition, you must set the X-10 controlled lights for that partition to the same house code. The letter that appears automatically after the house code number indicates the necessary HOUSE dial setting for X-10 modules in that partition.

To set the House Code:

1. With the desired partition selected, press

A or B until the

display shows HOUSE CODE nn-x (current setting).

2. Enter the desired numbers (1–255). The display flashes

the entered number. Press

ƒ and the display shows the

new house code.

Fire Panic

(Touchpad Options—Partition 1-2)

(partition 1: 0510, partition 2: 0520)

(Defaults = on) This setting determines whether touchpad fire panic buttons are enab led (on) or disabled (off).

To change the Fire Panic setting:

With the display showing FIRE PANIC OFF/ON (current setting), press

1 (off) or 2 (on). The display fla shes the

entered setting. Press ƒ and the display shows the new setting.

Aux. Panic

(Touchpad Options—Partition 1-2)

(partition 1: 0511, partition 2: 0521)

(Defaults = on) This setting determines whether touchpad auxiliary panic buttons are enabled (on) or disabled (off).

To change the Auxiliary Panic setting:

With the display showing AUXILIARY PANIC OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

DRAFT 8/17/00

Page 37

Programming the Panel

Note

Police Panic

(Touchpad Options—Partition 1-2)

(partition 1: 0512, partition 2: 0522)

(Defaults = on) This setting determines whether touchpad police panic buttons are enabled (on) or di sab led (off).

To change the Police Panic setting:

With the display showing POLICE PANIC OFF/ON (current setting), press

flashes the entered setting. Press

1 (off) or 2 (on).

ƒ and the display

The display

shows the new setting.

Keychain TP Arm

(Touchpad Options—Partition 1-2)

(partition 1: 0513, partition 2: 0523)

(Defaults = off) When this setting is on, pressing the lock button on keychain touchpads arms the system directly to A WAY with NO DELAY.

When this setting is off, each key-press increments the arming level (i.e., from OFF to STAY, from STAY to AWAY).

To change the Keychain Touchpad Arming setting:

With the display showing KEYCHAIN TP ARM OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Star Is No Delay

(Touchpad Options—Partition 1-2)

(partition 1: 0514, partition 2: 0524)

(Defaults = off) This setting determines whether the keychain touchpad star button controls an output (off) or the NO DELAY feature (on).

To change the keychain Star Is No Delay setting:

With the display showing STAR IS NO DELAY OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Buffer Control

(Reporting—Global)

(06001)

(Default = off) When this setting is on, only arming level changes are logged in the buffer (memory) of the panel.

When this setting is off, all system events are logged in the buffer.

To turn Buffer Control off or on:

With the display showing BUFFER CONTROL OFF/ON (current setting), press

flashes the entered setting. Press

1 (off) or 2 (on). The display

ƒ and the display

shows the new setting.

Back In Service

(Reporting—Global)

(06002)

(Default = on) When this setting is on, the panel reports to the central station when AC and backup battery power are restored (after an extended power outage) .

To turn Back In Service reports off or on:

With the display showing BACK IN SERVICE OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Bypass Reports

(Reporting—Global)

(06003)

(Default = off) When this setting is on, the panel reports to the central station whenever sensors or zones are bypassed.

To turn Bypass Reports off or on:

With the display showing BYPASS REPORTS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Reporting Menu

The REPORTING menu lets you set up which system events are reported to the central monitoring station.

The following describes how to program the reporting settings that appear under GLOBAL.

24-Hour Tamper

(Reporting—Global)

(06000)

(Default = off) When this setting is on, the panel sounds sirens and reports a tamper alarm (even when the system is disarmed), when wireless sensor tamper switches are activated.

Note

For commer cia l U L Li ste d ins tal lations (UL 1610) the 24-Hour Tamper must be set to on.

To turn 24-Hour Tamper off or on:

With the display showing 24 HOUR TAMPER OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

DRAFT 8/17/00

Low CPU Battery

(Reporting—Global)

(06004)

(Default = on) When this setting is on, the panel reports a low panel battery to the central station before shutting down.

For UL Listed installations, the Low CPU Battery feature must be set to on.

To turn Low CPU Battery reports off or on:

With the display showing LOW CPU BA TTERY OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Page 38

Programming the Panel

Battery Restoral

(Reporting—Global)

(06005)

(Default = off) When this setting is on, the panel reports to the central monitoring station when a wireless sensor reports a battery replacement to the panel.

To turn Battery Restoral reports off or on:

With the display showing BATTERY RESTORAL OFF/ ON (current setting), press

1 (off) or 2 (on). The

display flashes the entered setting. Press ƒ and the display shows the new setting.

Buffer Full Rpt

(Reporting—Global)

(06006)

(Default = off) When this setting is on, the panel sends an “event buffer full” report to the central monitoring station when the event buffer is nearly full.

To turn Buffer Full Report off or on:

With the display showing BUFFER FULL RPT OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Zone Restorals

(Reporting—Global)

(06007)

(Default = off) When this setting is on, the panel reports a restoral to the central monitoring station for wireless or hardwire zones in alarm before the alarm is canceled.

Note

As with all ITI panels, hardwire smoke detectors connected to Concord 2.0 or SnapCard hardwire zones do not send restorals.

To turn Zone Restoral reporting off or on:

With the display showing ZONE RESTORALS OFF/ON (current setting), press

flashes the entered setting. Press

1 (off) or 2 (on). The display

ƒ and the display

shows the new setting.

TP Panic RPT FMT

(Reporting—Global)

(06009)

(Default = off) This setting determines how the panel formats touchpad panic alarm reports to the central station.

When this feature is turned on, touchpad panic alarms repor t using the following 3-digit codes: Auxiliary—597, Police—598, Fire—599

When turned off, touchpad panic alarms report using a 3-digit code from 500 to 515, with the last digit identifying the touchpad device number.

To turn TP Panic RPT FMT off or on:

With the display showing TP PANIC RPT FMT OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

AC Failure

(Reporting—Global)

(06010)

(Default = off) When this setting is on, the panel reports to the central station 15 minutes after AC power to the panel is lost.

Note

For UL Listed installations, AC Failure must be set to on.

To turn AC Failure reports off or on:

With the display showing AC FAILURE OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Receiver Failure

(Reporting—Global)

(06011)

(Default = off) When this setting is on, the panel reports a receiver failure under the following conditions:

❑ No wireless sensor signals have been received for two

hours or

❑ The receiver is being jammed with a constant signal.

Two Trip Error

(Reporting—Global)

(06008)

(Default = off) This setting works with the ALARM VERIFY setting (see “ALARM VERIFY” later in this section and “Appendix B: Table B1. Sensor Group Characteristics”). If ALARM VERIFY is on, then the panel waits for a second sensor trip before sending an alarm.

If TWO TRIP ERROR is also on and a second sensor trip does not occur within a 4-minute time period, then the panel sends an error report to the central monitoring station.

Note

For UL Listed installations, the Two Trip Error feature must be set to off.

To turn Two Trip Error off or on:

With the display showing TWO TRIP ERROR OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Note

For UL Listed installations using wireless devices, Receiver Failure must be set to on.

To turn Receiver Failure reports off or on:

With the display showing RECEIVER FAILURE OFF/ ON (current setting), press

1 (off) or 2 (on). The

display flashes the entered setting. Press ƒ and the display shows the new setting.

RF Low Bat Rpt

(Reporting—Global)

(06012)

(Default = weekly) This setting determines whether the panel sends daily or weekly low battery reports to the central monitoring station when a wireless device is reporting a low battery condition to the panel.

To set RF Low Battery Report to daily or weekly:

With the display showing RF LOW BAT RPT DAILY/ WEEKLY (current setting), press

1 (daily) or 2

(weekly). The display flashes the entered setting. Press

ƒ and the display shows the new setting.

DRAFT 8/17/00

Page 39

Programming the Panel

Note

RF Supv Report

(Reporting—Global)

(06013)

(Default = weekly) This setting determines whether the panel sends daily or weekly reports to the central monitoring station when the panel detects a supervisory condition in a wireless device.

To set RF Supv Report to daily or weekly:

With the display showing RF SUPV REPORT DAILY/ WEEKLY (current setting), press

1 (daily) or 2

(weekly). The display flashes the entered setting. Press

ƒ and the display shows the new setting.

Swinger Limit

(Reporting—Global)

(06014)

(Default = 1) This setting determines the maximum number of times (1–2) a sensor or zone can go into alarm (during a single arming period) before the panel automatically bypasses that sensor or zone. This feature only applies to sensors or zones in groups 00–20, 29, or 34.

When set to 1, the panel automatically bypasses a sensor or zone after it causes an alarm. When set to 2, the panel waits until a sensor or zone has caused a second alarm (during the same arming period) before bypassing it. At any setting, the automatic bypass is logged into the event buffer.

A bypassed sensor or zone will be cleared (automatically unbypassed) if the system receives no further activations from that sensor or zone over the next 48–50 hours.

Changing the arming level also clears all automatically bypassed sensor s and zones and resets the Swinger Limit count on all sensors and zones.

To set the Swinger Limit:

With the display showing SWINGER LIMIT n (current setting), press the desired number. The display flashes

the entered setting. Press

ƒ and the display shows the

new setting.

Program Report

(Reporting—Global)

(06015)

(Default = off) When this setting is on, the panel sends a report to the central station when someone enters or exits installer programming.

To turn Program Reporting on or off:

With the display showing PROGRAM REPORT ON/OFF (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting

The following sections describe the settings that appear under REPORTING—PARTITION 1-2.

Opening Reports

(Reporting—Partition 1-2)

(partition 1: 06100, partition 2: 06200)

(Defaults = off) When this setting is on, the panel sends an opening report to the central station after disarming the system.

To use this feature, the settings under the for the specific CS Phone or Pager number.

OPEN/CLOSE REPORTS

PHONES

menu must be turned on

To turn Opening Reports off or on:

With the display showing OPENING REPORTS OFF/ ON (current setting), press

display flashes the entered setting. Press

1 (off) or 2 (on). The

ƒ and the

display shows the new setting.

Closing Reports

(Reporting—Partition 1-2)

(partition 1: 06101, partition 2: 06201)

(Defaults = off) When this setting is on, the panel sends a closing report to the central station after arm i ng the system.

To use this feature, the settings under the for the specific CS Phone or Pager number.

OPEN/CLOSE REPORTS

PHONES

menu must be turned on

To turn Closing Reports off or on:

With the display showing CLOSING REPORTS OFF/ON (current setting), press

flashes the entered setting. Press

1 (off) or 2 (on). The display

ƒ and the display

shows the new setting.

Recent Closings

(Reporting—Partition 1-2)

(partition 1: 06102, partition 2: 06202)

(Defaults = on) When this setting is on, the panel sends a recent closing report to the central station if an alarm occurs within two minutes after the exit delay time expires. Such a report is used to identify a possible exit fault.

To turn Recent Closings off or on:

With the display showing RECENT CLOSINGS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

No Activity

(Reporting—Partition 1-2)

(partition 1: 06103, partition 2: 06203)

(Defaults = off) When this setting is on, the panel sends a no activity report to the central station when the activity timeout expires (see TIMERS—ACTIVITY TIMEOUT).

DRAFT 8/17/00

To turn No Activity reports off or on:

With the display showing NO ACTIVITY OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Page 40

Programming the Panel

Duress Option

(Reporting—Partition 1-2)

(partition 1: 06104, partition 2: 06204)

(Defaults = off) When this setting is on, the system can be controlled using a programmed duress code (see SECU- RITY—PARTITION n —DURESS CODE).

Do not use a duress code unless it is absolutely necessary. Using duress codes often results in false alarms due to code entry errors. If a duress code is absolutely necessary, use it with the audio verification module to reduce false alarms and accidental dispatches.

Note

For UL Listed installations, Duress Option must be set to off.

To turn Duress Option off or on:

With the display showing DURESS OFF/ON (current setting), press

1 (off) or 2 (o n). The display flashes the

entered setting. Press ƒ and the display shows the new setting.

Force Armed

(Reporting—Partition 1-2)

(partition 1: 06105, partition 2: 06205)

(Defaults = off) When this setting is on, the panel reports to the central monitoring station when a user “force arms” the system.

Note

Forced arming occurs if the user presses BYPASS when arming the system wi th op en s ensors or zones protesting.

Auto-forced arming occurs if the user BYPASS (when arming the system with open sensors/zones protesting)

Auto-forced arming itoring station.

and the siren time expires

always

reports to the central mon -

does not

press

To turn Force Armed off or on:

With the display showing FORCE ARMED OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Latchkey Format

(Reporting—Partition 1, 2)

(06106—partition 1, 06206—partition 2)

(Defaults = off) This setting determines whether the selected partition is set up for basic (off) or advanced (on) latchkey opening report operation.

Basic:

If the partition is armed by entering 2 (or 3) + CODE, disarming using a designated latchkey user code or keychain touchpad within an assigned time schedule sends a page.

or--

If the partition is armed by entering 2 (or 3) + CODE + 6 (LATCHKEY), disarmi n g u si ng a de s i g-

nated latchkey user code or keychain touchpad inside or outside of an assigned time schedule sends a page.

Advanced:

If the partition is armed by entering 2 (or 3) + CODE + 6 (LATCHKEY), disarming using a latchkey designated

user code or keychain touchpad within an assigned time schedule sends a page.

Refer to the User’ s Guide for complete Latchkey setup and operation.

To turn Latchkey Format off or on:

1. With the desired partition selected, press display shows LATCHKEY FORMAT OFF/ON (current setting).

2. Press

1 (off—basic) or 2 (on—advanced). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Freeze Alarm

(Reporting—Partition 1, 2)

(06107—partition 1, 06207—partition 2)

(Defaults = off) This setting determines whether the panel reports a freeze alarm to the central station or pager, when the selected partition’s energy saver module detects a temperature that matches a predetermined setting (see BUS DEVICES— UNIT ID—ENERGY OPTIONS—FREEZE TEMP).

To turn Freeze Alarm reporting off or on:

1. With the desired partition selected, press display shows FREEZE ALARM OFF/ON (current set- ting).

2. Press

1 (off) or 2 (on). The display flashes the entered

setting. Press ƒ and the display shows the new setting.

A or B until the

DRAFT 8/17/00

Page 41

Programming the Panel

Note

Alarm Verify

(Reporting—Partition 1-2)

(partition 1: 06108, partition 2: 06208)

(Defaults = off) This setting determines whether the panel reports to the central monitoring station after a single sensor or zone trip (off) or waits for a second trip before reporting (on).

This setting affects sensors/zones in groups 10 through 20. If Alarm Verify is set to on, group 18 responds the same as group 17 (see “Appendix B, Table B.1: Sensor Group Characteristics”).

Note

For UL Listed installations, Alarm Verify must be set to off.

To turn Alarm Verify off or on:

With the display showing ALARM VERIFY OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

System Tamper

(Reporting—Partition 1-2)

(partition 1: 06109, partition 2: 06209)

(Defaults = off) This setting determines how the panel handles possible tamper situations. When this feature is on, the panel reacts in the following two ways:

❑ The system goes into alarm if several attempts are made

to disarm the system with incorrect access codes (40 consecutive keypresses).

❑ The panel reports to the central station if a bus device

stops communicating with the panel.

Note

For UL Commercial Listed instal lations (UL 1610), System Tamper must be set to on.

To change the System Tamper setting:

With the display showing SYSTEM TAMPER OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Siren Options Menu

The SIREN OPTIONS menu lets you set up siren operation and supervision.

The following describes how to program the siren option settings that appear under GLOBAL.

Immediate Beeps

(Siren Options—Global)

(0700)

(Default = off) This setting determines whether the panel activates trouble b eeps as soon as a wireless device superviso ry condition is detected (on), or if the panel waits until “supervisory time” to activate trouble beeps (off). (Refer to TIMERS— GLOBAL—SUPERVISORY TIME).

For UL Listed installations, this feature must be on.

To turn Immediate Beeps off or on:

With the display showing IMMEDIA TE BEEPS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Disable Trouble Beeps

(Siren Options—Global)

(0701)

(Default = off) When this setting is on, the panel will not beep to alert users of wireless device supervisory trouble.

For UL Listed installation s, Disable Trouble Beeps must be set to off.

To turn Disable Trouble Beeps off or on:

With the display showing DISABLE TR BEEPS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

UL 98 Options

(Siren Options—Global)

(0702)

(Default = off) This setting determines whether the panel complies with UL 98 requirements (4-hour trouble beep restart, 4-hour backup battery test, 4-hour smoke (group 26) zone supervisory).

DRAFT 8/17/00

For UL Listed installations, this feature must be on.

To turn UL 98 Options off or on:

With the display showing UL 98 OPTIONS OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

Page 42

Programming the Panel

SWS Supv Code

(Siren Options—Global)

(0703)

(Default = 3) This setting determines the system house code number used for su pervising wireless sirens.

Note

To supervise wireless sirens, Concord 2.0 hardwire panels must include a SuperBus 2000 RF Receiver. For all Concord 2 .0 pane ls, the s iren m ust b e learned into sensor group 33 for the system to process radio signals from wireless sirens.

Supervised Wireless Sirens receive signals from the panel through the existing electrical wiring. If sirens fail to receive or process these signals, the siren transmits a wireless signal to the panel/ receiver.

Note

You must set both the SWS Supv Code and the partition House Code (see the

before

plugging in Supervised Wireless Sirens.

LIGHT CONTROL

menu)

To set the SWS Supv Code:

With the display showing SWS SUP V CODE nn n (curr ent code), enter the desired code (1–255). The display flashes

the entered code. Press

ƒ and the display shows the new

code.

Global Fire

(Siren Options—Global)

(0704)

(Default = off) This setting determines whether or not sirens in both partitions sound (on) if either partition activates a fire alarm.

To turn Global Fire off or on:

With the display showing GLOBAL FIRE OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

The following sections describe the settings that appear under

SIREN OPTIONS—PARTITION 1.

Sensors Menu

The SENSORS menu gives you access to the following settings:

❑ LEARN SENSORS lets you add (learn) hardwire zones and

wireless sensors into panel memory.

❑ SENSOR TEXT lets you “name” the sensors and zones you

have added to the sys t em.

❑ DELETE SENSORS lets you delete zones and sensors

from panel memory.

❑ EDIT SENSORS lets you view and, if desired, change a

sensor group or partition assignment. You can also identify whether a zone is wireless or hardwire , whether it is configured as Normally Closed (N/C) or Normally Open (N/O), or if the zone is a touchpad.

Table 7. How to trip sensors

Hardwire Zones—Start with the zone in its “normal”

❑

state, then trip the zone into its alarm state. A normally closed door, for example, should be closed when you begin the Learn Sensors process. To trip the zone, open the door.

❑ Wireless Sensors—follow the instructions included

with each sensor.

❑ Wireless Door/Window Sensors with External Con-

tacts—place the external contact in the alarm condition, then activate the sensor tamper switch.

❑ Self Actuated Bell—activate the tamper switch. ❑ Handheld Wireless Touchpads—press the BYPASS

button.

❑ Keychain Touchpads—press and hold the lock and

unlock buttons together until the touchpad LED flashes.

❑ ELM Keychain Touchpads—

a.) Press and release the unlock button twice quickly, then press and hold until the LED flashes three times.

b.) Press and release the unlock button once quickly , then press and hold until the LED flashes two times.

c.) Press and hold the unlock button until the LED flashes once.

Siren Verify

(Siren Options—Partition 1)

(0710)

(Default = off) This setting determines whether or not the panel supervises the panel speaker terminals (7–8). When this feature is on, the panel will indicate a trouble condition if no speaker is connected to panel speaker terminals.

Note

For UL Listed insta llations , Siren V e rify must be set to on.

To turn Siren Verify off or on:

With the display showing SIREN VERIFY OFF/ON (current setting), press

1 (off) or 2 (on). The display

flashes the entered setting. Press ƒ and the display shows the new setting.

DRAFT 8/17/00

Page 43

Programming the Panel

The following describes how to program the sensor settings that appear under LEARN SENSOR S.

Learn Sensors

(Sensors)

(080)

(Default = none) The following describes how to ad d (learn) hardwire zones and wireless devices into panel memory.

To add sensors into panel memory:

1. With the display showing SENSORS, press

ƒ and the

display shows LEARN SENSORS.

2. Press

3. Press

ƒ and the display shows SENSOR PTN 1. ƒ to select partition 1 or press 2 + ƒ to select par-

tition 2. The display should show SENSOR GROUP 0.

4. Enter the desired sensor group +

ƒ (see table B.1 in

“Appendix B” for a description of all sensor group characteristics). The display shows TRIP SENSOR nn, where nn is the displayed (next available) sensor number.

5. To change the displayed sensor number, enter the desired

sensor number +

ƒ. The desired sensor number is dis-

played.

6. With the desired sensor number displayed, use the guidelines in T able 7 to force the sensor or zone you are adding (learning) into the panel memory to send a signal to the panel.

7. To add another sensor to the same sensor group and partition, go back to step 5.

8. To add sensors to another sensor group or partition, press

‚ twice and go back to step 1 (LEARN SENSORS).

Note

Sensors must be placed in a partition and group. To change the sensor group or partition assignment after adding a sensor or zone, use the

SORS

menu.

EDIT SEN-

Sensor Text

(Sensors)

(081)

(Default = none) Use the following guidelines to “name” zone and sensor locations:

❑ Use the item numbers that appear in “Appendix B, T able

B.2” for characters and words listed there.

❑ If a desired word does not appear in Table B.2, create it

using the characters (custom text).

❑ When using words from Table B.2, spaces between

them appear automatically. When using characters from Table B.2 to create words, you must reserve an item number for a ‘space’ after the word.

❑ Each character or word uses up one item number. For

example, a word from the list counts as one item number. A created word (such as BOY’S) counts as six item numbers—4 letters, 1 apostrophe, and 1 space.

❑ Only 16 item numbers are allowed for each zone or sen-

sor name, so plan ahead before programming s ensor text. You may need to abbreviate words to avoid running out of item numbers.

To program Sensor Text:

1. Press

2. Press

3. Press

A or B until the display shows SENSOR TEXT. ƒ and the disp l ay shows TEXT FOR SN 01. A or B until the display shows the desired sensor

number (or enter the desired sensor number and press ƒ).

4. Press

ƒ and the disp l ay shows:

Sn 1 ITEM 0

0 - ________

where ITEM 0 is the first character/word location and 0 is the character/word number.

5. Enter the number of the desired character or word, or scroll through th e num bers by pressi ng

B (forward) or A

(backward). If you make a mistake, simply enter the correct number or continue scrolling through choices.

6. Press

ƒ to accept the displayed choice and the display

shows:

Sn 1 ITEM 1 0 -________

7. Repeat steps 5 and 6 as needed to complete the zone or sensor name.

8. Press

‚ after entering the last character or word number.

The display shows the complete text name. For example:

TEXT FOR SN 01____

FRONT ENTRY DOOR

DRAFT 8/17/00

Page 44

Programming the Panel

Audio Verification Menu

Delete Sensors (082)

(Default = none) The following procedure describ es how to remove hardwire zone and wireless sensor numbers from panel memory.

Note

Deleting sensors does not delete sensor text associated with the deleted sensor number. To delete sensor text, enter the SENSOR TEXT menu and enter 000 (nulls) for each item number.

To Delete Sensors from panel memory:

1. Press

2. Press

3. Press

Repeat steps 2 and 3 until all desired sensors are deleted.

Edit Sensors (083)

(Default = none) This menu lets you view and, if desired, change the group and partition assignment for each learned zone or sensor. For example, the display shows:

where: S01 = zone/sensor number,

P1 = partition 1, G13 = sensor group 13, NC = normally closed, HW = hardwired, and BACK DOOR is the programmed text name.

To Edit Sensors:

1. Press

2. Press

3. Press

4. When the desired zone or sensor is displa yed, press

5. Enter the desired partition number, then press

6. Press

7. Enter the desired group number, then press

A or B until the display shows DELETE SEN-

SORS.

ƒ and the display shows DELETE SENSOR NN

(lowest zone/sensor number in panel memory).

ƒ to delete the di splayed sensor or—enter the

desired sensor number, then press ƒ.

S01 P1 G13 NC HW

BACK DOOR

A or B until the display shows EDIT SENSORS. ƒ and the display shows the sensor or zone w ith the

lowest number.

A or B to scroll through all learn ed zones and

sensors. The display shows SENSOR PTN n (current partition

assignment). display shows the new partition assignment.

A or B and the display show s SENSOR GROUP nn

(current group assignment).

display shows the new group assignment.

(Sensors)

ƒ.

ƒ. The

The AUDIO VERIFICATION menu lets you set up the audio verification module (AVM) operation in partition 1. If you want audio verification for partition 2, you must install a “stand-alone” audio verification module and a 4-Relay Output Module (HOM) (60-770) output for that partition.

The following sections describe the audio verification settings that appear under PARTITION 1.

Audio Verify (0900)

(Default = off) This setting determines whether or not the system can be accessed by phone for alarm verification.

To turn Audio Verification off or on:

1. With the display showing AUDIO VERIFICATION, press

(Audio Verification—Partition 1)

ƒ. The display shows PAR TITIO N 1.

2. Press

3. Press

Audio Mode (0901)

(Default = 01) This setting determines how the audio verification module operates. Choose one of the following:

ƒ again and t he display shows AUDIO VERIFY

OFF/ON (current setting).

1 (off) or 2 (on). The display flashes the entered

setting. Press ƒ and the display shows the new setting.

(Audio Verification—Partition 1)

❑ (01) Instant—Allows the central station operator

instant access for an audio session by entering the A VM code or by pressing ‚ (if an AVM access code is not programmed) upon completion of panel alarm report (also see ACCESS TIMEOUT).

❑ (02) Callback—Allows the central station operator to

contact persons on the premises after one ring and verify the alarm report. Operator must press ‚ or enter the AVM access code within 20 seconds after ring. The panel does not report any alarms during the AVM session, except for fire alarms.

❑ (03) Callback Silent—Same as Callback, except pre-

mises phones do not ring.

To set Audio Mode:

1. With the display showing AUDIO VERIFY OFF/ON, press

A or B until the display shows AUDIO MODE nn

(current setting).

2. Enter the desired mode number (01–03). The di splay flashes the entered setting. Press the new setting.

Fire Shutdown (0902)

(Default = off) This setting determines whether system sirens turn off during a fire alarm audio session.

(Audio Verification—Partition 1)

ƒ and the display shows

To turn Fire Shutdown off or on:

1. With the display showing AUDIO VERIFY OFF/ON,

2. Press

A or B until the display shows FIRE SHUTDOWN

press OFF/ON (current setting).

1 (off) or 2 (on). The display flashes the entered

setting. Press ƒ and the display shows the new setting.

DRAFT 8/17/00

Page 45

Programming the Panel

Note

Silent Talkback

(Audio Verification—Partition 1)

(0903)

(Default = off) This setting determines whether the central station operator can speak to persons on the premises (on) or only listen (off) during a silent or duress alarm audio session.

To turn Silent Talkback off or on:

1. With the display showing AUDIO VERIFY OFF/ON, press

A or B until the display shows SILENT TALK-

BACK OFF/ON (current setting).

2. Press

1 (off) or 2 (on). The display flashes the entered

setting. Press ƒ and the display shows the new setting.

Access Timeout

(Audio Verification—Partition 1)

(0904)

(Default = 90s) If the Audio Mode is set to “Instant,” then this setting determines how much time (30–300s, in 2-second increments) the central station operator has to enter the AVM access code after the panel is accessed for an audio session.

To change the Access Timeout:

1. With the display showing AUDIO VERIFY OFF/ON,

A or B until the display shows ACCESS TIMEOUT

press nn SECS (current setting).

2. Enter the desired time. The display flashes the entered setting. Press

ƒ and the display shows the new setting.

Accessory Modules Menu

The ACCESSORY MODULES menu gives you access to the following menus:

❑ BUS DEVICES—this menu lets you read bus device unit

numbers, assign bus devices to a partition, and configure other features associated with a specific bus device.

❑ SNAPCARDS—this menu lets you set the configuration

number for each SnapCard output, assign SnapCard outputs to a partition, and name the SnapCard outputs.

The following procedure describes how to program the settings that appear under

DEVICES

Most settings under

DEVICES

have no shortcut numbers.

ACCESSORY MODULES—BUS

Beep Delay

(Audio Verification—Partition 1)

(0905)

(Default = 02s) This setting determines how long A VM access beeps are delayed (0–300s, in 2-second intervals) at the beginning of a 2-way au di o session.

To change the Beep Delay:

1. With the display showing AUDIO VERIFY OFF/ON, press

A or B until the display shows BEEP DELAY nn

SECS (current setting).

2. Enter the desired time. The display flashes the entered setting. Press

Access Code

ƒ and the display shows the new setting.

(Audio Verification—Partition 1)

(0906)

(Default = none) This setting determines the code required to access the audio verification module to start an audio session. If no code is programmed, pressing

‚ starts an audio session.

To change the Access Code:

1. With the display showing AUDIO VERIFY OFF/ON, press

A or B until the display shows ACCESS CODE

nnnn (current code).

2. Enter the desired 4-digit access code. The display flashes the entered code. Press

ƒ and the display shows the new

setting.

To delete an Access Code:

1. With the display showing AUDIO VERIFY OFF/ON,

press

A or B until the display shows ACCESS CODE

nnnn (current code).

2. Press

D to delete.

DRAFT 8/17/00

Page 46

Programming the Panel

Unit - ID

(Acc. Modules—Bus Devices)

(10000 thru 10015)

(Default = none) This menu lets you identify all connected bus devices, view each Unit Number, view the Device ID number, and configure other settings based on a specific device. This menu also lets you delete learned bus devices.

To identify bus device Unit and ID:

1. With the display showing BUS DEVICES, press

ƒ. The

display shows the bus Unit Number and the 8-digit Device ID number. For example:

UNIT - ID

0—02110185

where 0 is the Unit Number and 02110185 is the Device ID number.

Note

To help identify bus devices, the 8-digit Device ID number is also located on a label on each SuperBus 2000 device.

2. Press A or B to identify all other bus Unit Numbers (0–

15) and Device ID numbers.

To delete learned Unit Numbers:

1. With the display showing BUS DEVICES, press

ƒ. The

display shows the bus device set to Unit Number 0.

2. Press

A or B until the bus device Unit Number you want

to delete is displayed.

3. Press

D. The display change s the Unit Number to NONE.

Partition Assign

(Acc. Modules—Bus Devices

—Unit ID—

Device Partition)

(Default = 1) This menu lets you assign bus devices to work in the desired partition.

Note

SuperBus 2000 8Z Input Modules, SuperBus 2000 4Relay Output Modules, and SuperBus 2000 RF Receivers are not assigned to partitions.

To assign bus devices to partitions:

1. With the display showing the desired bus device, press

2. Press then press

3. Press

until the display shows DEVICE PTN and

ƒ. The display shows PARTIT ION ASSIGN n.

1 or 2 to select the desired partition. The display

ƒ.

flashes the entered selection. Press ƒ and the display shows the new setting.

Output Programming

(Acc. Modules—Bus Devices—

Unit ID—Outputs)

Use these settings to program the output points of any installed SuperBus 2000 Hardwire Output Module. The installer programs a HOM output point into the Concord 2.0 security panel by entering three kinds of information.

1. Partition: the system partition (1 or 2).

2. Trigger: the event that activates the output point. Trigger

events can be partition alarms, trouble conditions, open sensors, etc. (see Appendix C, Tables C.1–C.4).

3. Response: how the output responds when trigger event

occurs (see Appendix C, Tables C.5–C.6).

Device ID

(Acc. Modules—Bus Devices—Unit ID—

Change ID)

(Default = none) This menu lets you change the bus device ID number when replacing a defective bus dev i ce.

To change a Device ID:

1. With the display showing the desired bus device, press +

ƒ. The display shows DEVICE ID (current ID).

2. Enter the ID of the new bus device. The display flashes the entered selection. Press

ƒ and the display shows the

new setting.

3. Exit programming mode.

4. Remove AC and battery p ower from the panel.

5. Replace the defective bus device with a new one.

6. Apply AC and battery power to the panel.

This section describes how to program each of the HOM output point configurations into the security panel. The point configuration number is tttrr, where ttt is the trigger number and rr is the response number.

Note

HOM output points cannot be configured for user control. Only the onboard and Sna pCard out put s can be configured for user control.

1. With the display showing the desired bus device,

ƒ.

press

2. Press

3. Press

4. Press

A or B until the display shows OUTPUTS. ƒ. The display shows OUTPUT 1. A or B to select an output, then press ƒ. The

display shows PARTITION ASSIGN 1.

5. Press

1 or 2 to select the desired partition assignment

for this relay. The display flashes the entered setting. Press ƒ and the display shows the new setting.

6. Press

A or B. The display shows CONFIGURATION

tttrr (current setting).

7. Enter the desire d 5-dig it configuration number for this relay. The display flashes the entered setting. Press and the display shows the new setting.

8. Press

ƒ and repeat steps 4 through 8 until all outputs are

programmed

DRAFT 8/17/00

Page 47

Programming the Panel

Note

Status Beeps

(Acc. Modules—Bus Devices

—Unit ID

—Keypad Options)

(Default = on) This setting determines whether or not the selected touchpad sounds status beeps. Each touchpad can be set individually.

This feature is usually turned off for a touchpad that is located in or near bedrooms, to avoid disturbing sleeping persons.

Note

For UL Listed i nstall ati ons, Sta tus Beeps mu st be set to on.

To turn touchpad Status Beeps on or off:

1. With the display showing the desired touchpad, press

then A or B until the display shows KEYPAD OPTIONS.

2. Press

ƒ and the display shows STATUS BEEPS OFF/ON

(current setting).

3. Press

1 (off) or 2 (on) to select the desired setting. The

display flashes the entered selection. Press ƒ and the display shows the new setting.

Key Beeps

(Acc. Modules—Bus Devices

—Unit ID

—Keypad Options)

(Default = on) This setting determines whether or not selected touchpads beep when their buttons are pressed.

This feature is usually turned off for a touchpad that is located in or near bedrooms, to avoid disturbing sleeping persons.

To turn Key Beeps on or off:

1. With the display showing the desired touchpad, press

then A or B until the display shows KEYPAD OPTIONS. Next, press

ƒ then A or B until the display shows KEY

BEEPS OFF/ON (current setting).

2. Press

1 (off) or 2 (on) to select the desired setting. The

display flashes the entered selection. Press ƒ and the display shows the new setting.

Freeze Temp

(Acc. Modules—Bus Devices

—Unit ID

—Energy Options)

(Default = 42°F) This setting determines the temperature point that the Energy Saver Module detects a potential freeze (heating failure) condition. The adjustable range is from 40°F to 90°F.

To change the Freeze Temp setting:

1. With the display showing the desired bus device press

ƒ,

then A or B until the display shows ENERGY OPTIONS. Next, press

ƒ and then A or B until the display shows

FREEZE TEMP nn DEGREES (current setting).

2. Enter the desired freeze temperature (40–90). The dis-

play flashes the entered selection. Press

ƒ and the display

shows the new setting.

Temperature

(Acc. Modules—Bus Devices

—Unit ID

—Energy Options)

(Default = none) This setting lets you adjust the Energy Saver Module (ESM) room temperature setting to match the premises thermostat. The adjustable range is from 40°F–90°F.

To ensure accuracy, wait at least 15 minutes before setting the ESM temperature to allow the ESM to warm or cool to actual room temperature.

To change the ESM Temperature setting:

1. With the display showing the desired bus device press

ƒ,

then A or B until the display shows ENERGY OPTIONS. Next, press ƒ and then A or B until the display shows TEMPERATURE nn DEGREES (current setting).

2. Enter the desired temperature (40–90). The displ ay

flashes the entered selection. Press

ƒ and the display

shows the new setting.

The following describes how to program the settings that appear under SNAPCARDS.

Output Programming

(Acc. Modules—SnapCards

—Ouput Programming

(Defaults: Partition Assign =all 1, Configuration Output 1 = 01400, Output 2 = 00410, Output 3 = 00903, Output 4 =

01003) This setting lets you assign a partition and a 5-digit configura-

tion number for each SnapCard relay outpu t. This number determines both which system event activates the output and the duration or time the output is activated.

1. Partition: the system partition (1 or 2).

2. Configuration number: The combination of a trigger and a response.

Trigger: the event that activates the output point. Trigger events can be partition alarms, trouble conditions, open sensors, etc. (see Appendix C, Tables C.1–C.4).

Response: how the output responds when trigger event occurs (see Appendix C, Tables C.5–C.6).

This section describes how to program each of the output point configurations into the security panel. The point configuration number is tttrr, wh ere ttt is the trigger number and rr is the response number.

To assign configuration numbers to SnapCard Relay outputs:

1. With the display showing SNAPCARDS, press

ƒ. Then

press A or B until the display shows OUTPUT PROGRAMMING.

2. Press

3. Press

ƒ again and the display shows OUTPUT 1. A or B to select the desired output (1–4), then

press ƒ.

4. With the display showing PARTITION ASSIGN 1, press

or 2 to select the desired partition. Press

ƒ to con-

firm the partition.

5. Press

A or B until the display shows CONFIGURATION

tttrr (current setting).

6. Enter the desired 5-digit configuration number for this

relay. Press

7. Press

ƒ to confirm the setting.

ƒ and repeat steps 3 through 6 until all outputs are

programmed.

)

DRAFT 8/17/00

Page 48

Programming the Panel

Output Text

(Acc. Modules—SnapCards

—Ouput Text

)

(10110—output 1, 10111—output 2, 10112—output 3, 10113—output 4)

(Defaults = none) Entering text for an output allows the user to control it directly or by schedule. Use the following guidelines to “name” SnapCard outputs:

❑ Use the item numbers that appear in “Appendix B, T able

B.2” for characters and words listed there.

❑ If a desired word does not appear in Table B.2, create it

using the characters (custom text).

❑ When using words from Table B.2, spaces between

them appear automatically. When using characters from Table B.2 to create words, you must reserve an item number for a ‘space’ after the word.

❑ Each character or word uses up one item number. For

example, a word from the list counts as one item number. A created word (such as BOY’S) counts as six item numbers—4 letters, 1 apostrophe, and 1 space.

❑ Only 16 item numbers are allowed for each output

name, so plan ahea d before programming output text. You may need to abbreviate words t o avoid running out of item numbers.

Note

If you desire an output for User Output Control you must use the Out put Text feature to name the output. If no Output Text is programmed, the user will not have access to the output.

To program Output Text:

1. With the display showing SNAPCARDS, press or

B until the display shows OUTPUT TEXT.

2. Press

3. Press

ƒ and the display shows OUTPUT 1. A or B until the desired output number is dis-

ƒ, then A

played.

4. Press

ƒ and the display shows:

OUTPUT n ITEM 0

0 - ________

where ITEM 0 is the first character/word location and 0 is the character/word number.

5. Enter the number of the desired character or wo rd, or scroll through th e num bers b y pressi ng

B (forward) or A

(backward). If you make a mistake, simply enter the correct number or continue scrolling through choices.

6. Press

ƒ to accept the displayed choice and the display

shows:

OUTPUT n ITEM 1

0 -

7. Repeat steps 4 and 5 as needed to complete the output name.

8. Press

‚ after entering the last character or word nu mber.

The display shows the complete text name. For example:

OUTPUT 1_

GARAGE DOOR

Onboard Options Menu

The ONBOARD OPTIONS menu lets you set up the following built-in options:

INPUTS—This menu lets you turn the Smoke Verification and the Two Wire Smoke features off or on.

OUTPUT PROGRAMMING—This menu lets you set configuration numbers for the two built-in panel outputs and assign the outputs to partitions.

OUTPUT TEXT—This menu lets you assign text to the output allowing the output to be controlled by the user.

The following sections describe the settings that appear under

ONBOARD OPTIONS—INPUTS

Smoke Verify

(Onboard Options—Inputs)

(1100)

(Default = off) This setting determines whether the panel requires one alarm signal (off) or two alarm signals within five minutes (on) before activating system sirens and reporting to a central station. This setting affects 2-wire smoke detectors connected to a SnapCard zone input or any other hardwire zone learned into sensor group 26 (FIRE).

Note

For California State Fire Marshall (CSFM) Listed installations, Smoke Verify must be set to off.

To turn Smoke Verify off or on:

1. With the display showing ONBOARD OPTIONS, press twice. The display shows SMOKE VERIFY OFF/ON (current setting).

2. Press

1 (off) or 2 (on). The display flashes the entered

number. Press ƒ and the display shows the new setting.

Two Wire Smoke

(Onboard Options—Inputs)

(1101)

(Default = off) This setting determines how onboard hardwire zone 8 is configured. When this setting is on, zone 8 will be configured for two wire smoke detectors. When off, it will be configured for a normal hardwire in put.

To turn Smoke Verify off or on:

1. With the display showing ONBOARD OPTIONS, press twice. The display shows SMOKE VERIFY OFF/ON (current setting).

2. Press

A or B until the display shows TWO WIRE

SMOKE ON/OFF (current setting).

3. Press

1 (off) or 2 (on). The display flashes the entered

number. Press ƒ and the display shows the new setting.

DRAFT 8/17/00

Page 49

Programming the Panel

Note

The following sections describe the settings that appear under ONBOARD OPTIONS—OUTPUT PROGRAMMING.

Output 1, 2

(Onboard Options

Output Programming

Output 1: partition assi gn — 11 10 0, co nf igu ra tio n— 1 11 01 Output 2: partition assi gn — 11 11 0, co nf igu ra tio n— 1 11 11

(Defaults: Output 1 = Ptn 1, 01614; Output 2 = Ptn. 2, 01710) This setting lets you assign the partition and the 5-digit configuration number.

The configuration number determines

❑ which system event activates the selected output, and ❑ the duration or time the output is activated.

The first three digits represent the trigger number of an event (such as triggering an alarm, opening a sensor, or arming the system). The last two digits represent how the output responds (such as momentary switching, maintained (or latched) switching, or switching for a preset time).

Note

If you want to configure an output for user Output Control you m ust use the Ou tput Text feature to n ame the output. If no Output Text is programmed, Output Control will not function for that output.

Use the system event trigger and response numbers listed in Tables C.1–C.6, in “Appendix C.”

To set up onboard Output 1 & 2 partition and configuration assignments:

1. With the display showing ONBOARD OPTIONS, press

+ B. The display shows OUTPUT PROGRAMMING.

2. Press

ƒ and the display shows OUTPUT 1. Press B to

select OUTPUT 2.

3. Press

ƒ and the display shows PARTITION ASSIGN n

(current setting).

4. Press

1 or 2 to assign the output to the desired partition,

then press ƒ. The display shows PARTITION ASSIGN (new setting).

5. Press

B and the display shows CONFIGURATION tttrr

(current setting).

6. Enter the desired configuration number. The display

flashes the entered number. Press

ƒ and the display

shows the new setting.

7. Press

ƒ and repeat steps 2 through 6 until all outputs are

programmed.

Output Text

(Onboard Options

Output Text

—Output 1, 2)

(1120—output 1, 1121—output 2)

(Defaults = none) Use the following guidelines to “name” onboard outputs:

❑ Use the item numbers listed in “Appendix B, Table B.2”

for characters and words.

❑ If a desired word does not appear in Table B.2, create it

using the characters (custom text).

❑ When using words from Table B.2, spaces between

them appear automatically. When using characters from Table B.2 to create words, you must reserve an item number for a ‘space’ after the word.

❑ Each character or word uses up one item number. For

example, a word from the list counts as one item number. A created word (such as BOY’S) counts as six item numbers—4 letters, 1 apostrophe, and 1 space.

❑ Only 16 item numbers are allowed for each outpu t

name, so plan ahead before programming output text. You may need to abbreviate words to avoid runni ng out of item number s.

If you want to configure an output for user Output Control you mus t use the Output Text feature to name the output. If no Output Text is programmed, Output Control will not function for that output.

To program Output Text:

1. With the display sh owing ONBOARD OPTIONS, press then press B twice and the display shows OUTPUT

TEXT.

2. Press

3. Press

ƒ and the disp l ay shows OUTPUT 1. ƒ and the disp l ay shows:

OUTPUT 1 ITEM 0

0 - ________

where ITEM 0 is the first character or word location and 0 is the character or word number.

4. Enter the number of the desired character or word, or scroll through th e num bers by pressi ng

B (forward) or A

(backward). If you make a mistake, simply enter the correct number or continue scrolling through choices.

5. Press

ƒ to accept the displayed choice and the display

shows:

OUTPUT 1 ITEM 1

0 -________

6. Repeat steps 4 and 5 as needed to complete the output name.

7. Press

‚ after entering the last character or word number.

The display shows the complete text name. For example:

OUTPUT 1

GARAGE DOOR

DRAFT 8/17/00

Page 50

Programming the Panel

Exiting Programmin g Mode

After all installer/dealer programming is completed, use the following procedure to exit programming mode.

To exit programming mode:

1. Press ‚ until the display shows SYSTEM PROGRAMMING.

2. Press

3. Press

A or B until the display shows EXIT PROGRAM-

MING READY.

ƒ and the touchpad displays the time and date.

Entering User Programming Mode

The user programming mode lets you view system version information and program the following system settings:

❑ Time and Date ❑ User Codes ❑ Options ❑ Set Up Schedules ❑ Attach Schedules to Events ❑ Energy Saver ❑ Attach Lights to Sensors ❑ System Version

You can enter user programming from an alphanumeric touchpad by using the system or partition master code.

The system master code default is

To enter user-programming mode:

Press 9 + CODE. The display shows TIME AND DATE.

Time and Date Menu

The panel uses a global clock and calendar for time and date. Alphanumeric touchpads display the panel time and date whenever the system is disarmed.

The TIME AND DATE menu lets you set this clock and calen- dar. The following procedure tells you how.

Note

Setting the time and date is important for accurate tracking of system events stored in the event buffer.

Time (020)

(Default = 00:00) This setting lets you adjust the panel clock to the correct time. The panel uses a 24-hour clock. For example, to set the time to 4:17

1234.

., enter 1617.

P.M

(Time and Date)

Date (021)

(Default = 01/01/00) This setting lets you adjust the panel calendar to the correct month, day, and year.

To set the Date:

1. With the display showing TIME AND DATE, press then A or B until the display shows DATE nn/nn /nn (c ur- rent dat e).

2. Enter the correct month (01–12), day (01–31), and year (00–99). For example, enter 090100 for September 1,

2000. The display flashes the entered date. Press the display shows the new date.

(Time and Date)

ƒ,

ƒ and

User Codes Menu

The USER CODES menu lets you program/change regular user access codes, the partition master code, and the system master code. You can enter up to 60 separate user codes, allowing up to 60 different “users” access to the security system. You can also specify whether or not a specific user is able to perform specific actions like, bypass sensors or test the system.

User NN

(User Codes—Reg. User Codes

—User NN)

(030nn0 where nn=user number 00-59)

(Default = none) User codes perform b asic arming and disarming functions. The system allows up to 60 user codes (user numbers 00–59). User numbers that show code is currently programmed for that user number.

To program Regular User Codes:

1. With the display showin g USER CODES, press display shows REGULAR USER CODES.

2. Press

3. Press

4. With the desired user number displayed, enter a 4-digit

To delete Regular User Codes:

1. With the display showin g USER CODES, press

2. Press

3. Press

4. Enter the system or partition master code. The display

user number).

A or B to select the desired user number, then

press ƒ. The display shows USER nn - nnnn. user code. The display flashes the entered code. Press

and the display shows USER nn - nnnn (new code).

display shows REGULAR USER CODES.

available user number).

A or B to select the desired user number/user code

you want to delete (if it is not already displayed), then press ƒ. The display shows USER nn - nnnn.

flashes the entered code. Press

USER nn -

the display shows USER nn (first available

and

the display shows USER nn - nnnn (first

and

✱✱✱✱

(no code).

✱✱✱✱

indicate no

ƒ and the

ƒ and the display shows

To set the Time:

1. With the display showing TIME AND DATE , press the display shows TIME hh:mm (current time).

2. Enter the correct time (0000–2359). The display flashes the entered time. Press time.

ƒ and the display shows the new

ƒ and

DRAFT 8/17/00

Page 51

Programming the Panel

Note

Direct Bypassing

(User Codes—Reg. User Codes

—User NN)

(030nn1 where nn=user number 00-59)

(Default = off) This setting determines whether or not a specific user code provides access to the “bypass sensors” feature. Set this feature to “on” for all users who need to be able to bypass sensors.

To turn user code Direct Bypassing off or on:

1. With the display showing USER CODES, press display shows REGULAR USER CODES.

2. Press user number).

3. Press press ƒ. The display shows USER nn - nnnn.

4. Press ING OFF/ON (current setting).

5. Press setting. Press ƒ and the display shows the new setting.

Remote Access

and the display shows USER nn (first available

A or B to select the desired user number, then A or B until the display shows DIRECT BYPASS- 1 (off) or 2 (on). The display flashes the entered

(User Codes—Reg. User Codes

ƒ and the

—User NN)

(030nn2 where nn=user number 00-59)

(Default = off) This setting determines whether or not the user can access the panel from a remote phone (a phone located off the premises).

System Tests

(User Codes—Reg. User Codes

—User NN)

(030nn4 where nn=user number 00-59)

(Default = off) This setting determines whether or not a specific user code provides access to the phone and sensor tests. Set this feature to “on” for all users who need to be able to conduct phone and sensor tests.

To turn user code System Tests off or on:

1. With the display showing USER CODES, press display shows REGULAR USER CODES.

2. Press user number).

3. Press press ƒ. The display shows USER nn - nnnn.

4. Press OFF/ON (current setting).

5. Press setting. Press ƒ and the display shows the new setting.

Latchkey Report

the display shows USER nn (first available

and

A or B to select the desired user number, then A or B until the display shows SYSTEM TESTS 1 (off) or 2 (on). The display flashes the entered

(User Codes—Reg. User Codes

ƒ and the

—User NN)

(030nn5 where nn=user number 00-59)

(Defaults: 00–05 = on, 06–59 = off) This setting determines whether or not the user code causes a latchkey report to be sent to a pager when the code is used to change arming levels.

To turn user code Remote Access off or on:

1. With the display showing USER CODES, press display shows REGULAR USER CODES.

2. Press user number).

3. Press press ƒ. The display shows USER nn - nnnn.

4. Press OFF (current setting).

5. Press setting. Press ƒ and the display shows the new setting.

Partition Jump

and the display shows USER nn (first available

A or B to select the desired user number, then B until the display shows REMOTE ACCESS ON/ 1 (off) or 2 (on). The display flashes the entered

(User Codes—Reg. User Codes

ƒ and the

—User NN)

(030nn3 where nn=user number 00-59)

(Default = off) This setting determines whether or not a specific user code can access one or both partitions. When this is set to on, the user can access both partitions.

To turn user code Partition Jump off or on:

1. With the display showing USER CODES, press display shows REGULAR USER CODES.

2. Press user number).

3. Press press

4. Press ON (current setting).

5. Press setting. Press

and the display shows USER nn (first available

A or B to select the desired user number, then

ƒ. The display shows USER nn - nnnn.

B until the display shows PARTITION JUMP OFF/ 1 (off) or 2 (on). The display flashes the entered

ƒ and the display shows the new setting.

ƒ and the

To assign the Latchkey Report attribute to user codes:

1. With the display showing USER CODES, press display shows REGULAR USER CODES.

2. Press user number).

3. Press press ƒ. The display shows USER nn - nnnn.

4. Press ON (current setting).

5. Press setting. Press ƒ and the display shows the new setting.

Partition Master

the display shows USER nn (first available

and

A or B to select the desired user number, then A or B

until the display shows LATCHKEY OFF/

1 (off) or 2 (on). The display flashes the entered

(User Codes—

ƒ and the

Partition Master Code)

(partition 1: 0310, partition 2: 0311)

(Defaults = none) The Partition Master Code provides access to all system operations and user programming for a single partition.

You must be “in” the partition of the partition master code you wish to change.

To change the Partition Master Code:

1. With the display showing USER CODES, press or B until the display shows PARTITION MASTER CODE.

2. Press rent code).

3. Enter a new 4-digit code. The display flashes the entered code. Press

the display shows PARTITION nnn n (cu r-

and

ƒ and display shows the new code.

ƒ then A

DRAFT 8/17/00

Page 52

Programming the Panel

System Master

(User Codes—

System Master Code)

(0320)

(Default = 1234) The System Master Code provides access to all system operations and user programming.

To change the System Master Code:

1. With the display showing USER CODES, press

ƒ then A

or B until the display shows SYSTEM MASTER CODE.

2. Press

the display shows SYSTEM MASTER nnnn

and

(current code).

3. Enter a new 4-digit code. The display flash es the enter ed

code. Press

ƒ and display shows the new code.

Options Menu

The OPTIONS menu lets you set up the system for downloading and silent arming. You can also adjust alphanumeric touchpad display brightness from this menu.

Downloading

(Options)

(040)

(Default = on) When this setting is on, the panel can communicate with ITI ToolBox software for programming the system from off-site .

Note

For this f eature to work, the panel must be con nected to a phone line and be programmed with

ACCESS

with a Downloader code.

on, with a Downloader phone number, and

REMOTE

To turn Downloading off or on:

1. Press

2. Press

A or B until the display shows OPTIONS. ƒ, then A or B until the display shows DOWN-

LOADING OFF/ON (current setting).

3. Press

1 (off) or 2 (on). The display flashes the entered

selection. Press ƒ and the display shows the new setting.

Silent Arming

(Options)

(041)

(Default = off) This setting determines whether or not the panel sounds status beeps from sirens and the touchpad when the system is armed.

Note

When this feature is on, the user does not need to press 5 (SILENT) before arming the system to prevent status sounds.

To turn Silent Arming off or on:

4. Press

5. Press

A or B until the display shows OPTIONS. ƒ, then A or B until the display shows SILENT

ARMING OFF/ON (current setting).

6. Press

1 (off) or 2 (on). The display flashes the entered

selection. Press ƒ and the display shows the new setting.

Touchpad Brightness

(Options)

(042)

(Default = 2) This setting lets the user lighten or darken the background on touchpad displays. Each touchpad can be set to compensate for lighting conditions in the touchpad location.

To adjust Touchpad Brightness:

1. Press

2. Press

A or B until the display shows OPTIONS. ƒ, then A or B until the display shows TOUCH-

PAD BRIG HTNESS n (cur rent setting).

3. Enter a setting from 0 (darkest background ) to 3 (brightest

background). The display flashes the entered selection.

ƒ and the display shows the new setting.

Press

Volume

(Options)

(043)

(Default = 4) This setting determines the volume level of status sounds from speakers connected to the Phone Interface/ Voice Module.

Note

This menu appears Module is connected to the panel.

only

if a Phone Interface/Voice

To adjust status sound Volume:

1. Press

2. Next, press

A or B until the display shows OPTIONS, then ƒ.

press

A or B until the display shows VOLUME n

(current setting).

3. Enter a setting from 0 (off) to 7 (loudest). The display

flashes the entered selection. Press

ƒ and the display

shows the new setting.

Voice Chime

(Options)

(044)

(Default = on) This setting determines whether speakers connected to the Phone Interface/Voice Module announce perimeter sensor/zone numbers that are tripped when the Chime feature is on. For example, “Sensor one open.”

Note

This menu appears Module is connected to the panel.

only

if a Phone Interface/Voice

To turn Voice Chime off or on:

1. Press

2. Press

A or B until the display shows OPTIONS. ƒ then A or B until the display shows VOICE

CHIME OFF/ON (current setting).

3. Press

1 (off) or 2 (on). The display flashes the entered

selection. Press

ƒ and the display shows the new setting.

DRAFT 8/17/00

Page 53

Programming the Panel

Chime On Close

(Options)

(045)

(Default = off) When this setting is on, the panel sounds a single chime when a perimeter door or window is closed.

To turn Chime On Close off or on:

1. Press

2. Press

A or B until the display shows OPTIONS.

ƒ then A or B until the display shows CHIME ON

CLOSE OFF/ON (current setting).

3. Press

1 (off) or 2 (on). The display flashes the entered

selection. Press ƒ and the display shows the new setting.

Set Up Schedules Menu

The SET UP SCHEDULES menu lets you set up time frames for light control and exception opening/closing reports. The system (all partitions) allows you to set up to 16 schedules (00–

15). Setting up schedules consists of setting a start and stop time for

each schedule, then selecting which days of the week the schedule will be active. Y ou can also set up a rollover schedule, which starts on one day and ends on another day. This saves programming time and leaves more schedu les available (in case they are needed later).

Rollover Schedule Example: To set up a schedule to rollover from Tuesday evening to Wednesday morning, set a schedule start time for 2200 (10:00

.). Set the schedule to turn on Tuesday. Because the stop

A.M

.) and a stop time for 0500 (5 :00

P.M

time is set for morning, the system automatically carries the schedule over to the next day.

Set Up Schedules 05XXY where XX = schedule 00 thru 15 and Y = start (0)/stop(1) 0 thru 8—Monday thru Sunday (2–8))

(Defaults = 00:00) This menu lets you set up start/stop times for each day of the week.

To set up a Time Schedule:

1. Press

A or B until the display shows SET UP SCHED-

ULES.

2. Press

ƒ and the disp l ay shows SCHEDULE 00. If you

want a different schedule number, press A or B until the desired schedule number appears.

3. Press

ƒ and the display shows START TIME hh :m m (c ur-

rent setting).

4. Enter the desired starting time (00:00–23:59). The display flashes the entered time. Press

ƒ and the display

shows START TIME hh:mm (new setting).

5. Press

B and the disp l ay shows STOP TIME hh:mm (cur-

rent setting).

6. Enter the desired stop time (00:00–23:59). The display flashes the entered time. Press

ƒ and the display shows

STOP TIME hh:mm (new setting).

7. Press

B and the disp l ay shows MONDAY OFF/ON (cur-

rent setting). To select a different day, continue pressing

B until the desired day appears.

8. Press

1 (off) or 2 (on). The display flashes the entered

selection. Press

ƒ and the display shows the new setting

for the selected day.

9. Repeat steps 7 and 8 until all desired settings for each day are set.

If you use the same start and stop times described above and set the schedule to turn on Monday through Friday, then one schedule will cover the entire week.

Note

If you are programming schedules for your customer, be sure to record the settings in the

User’s Manual

Attach Schedules to Events Menu

The ATTACH SCHEDULES TO EVENTS menu lets you link the following system events to time schedules:

❑ Latchkey Opening—sends a report if system is disarmed

within the attached time schedule.

❑ Latchkey Closing—sends a report if system is armed

within the attached time schedule.

❑ Exception Opening—sends a report if system is not dis-

armed within the attached time schedule.

❑ Exception Closing—sends a report if system is not armed

within the attached time schedule.

❑ Lights (1–9) activate X-10 controlled lights by the

attached time schedule.

❑ Outputs (1–6) allow users to attach onboard (1–2) and

SnapCard outputs to a schedule.

❑ Arming—Allows the user to arm the panel at the schedule

start time.

DRAFT 8/17/00

Page 54

Programming the Panel

Latchkey Reports (060nn—Opening, 061nn—Closing where nn = Schedule number [0 to 15])

(Defaults = off) This setting lets you attach the Latchkey Opening report feature and the Latchkey Closing report feature to time schedules.

To Attach a Schedule to Latchkey Opening or Latchkey Closing:

1. Press

2. Press

3. Press

A or B until the display shows ATTACH SCHED-

ULES TO EVENTS.

ƒ then A or B until the display shows LATCHKEY

OPENING or LATCHKEY CLOSING.

ƒ and the display shows SCHEDULE 00 OFF/ON

(current setting). If you want a different schedule, press

Attach Schedules To Events

A or B until the desired schedule appears.

4. Press

Exception Reports (062nn—Opening, 063nn—Closing, where nn = Schedule number [0 to 15])

(Defaults = off) This setting lets you attach the Exception Opening report feature and the Exceptio n Closing report feature to time schedules.

To Attach a Schedule to Exception Opening or Exception Closing:

1. Press

2. Press

3. Press

1 (OFF) or 2 (ON). The display flashes the

entered selection. Press setting for the selected schedule.

ƒ and the display shows the new

Attach Schedules To Events

A or B until the display shows ATTACH SCHED-

ULES TO EVENTS.

ƒ then A or B until the display shows EXCEP-

TION OPENING or EXCEPTION CLOSING.

ƒ and the display shows SCHEDULE 00 OFF/ON

(current setting). If you want a different schedule, press

A or B until the desired schedule appears.

4. Press

Lights (064xnn where nn = Schedule number [0 to 15] and x = light number [1 to 9] minus 1)

(Defaults = off) This setting lets you attach light controls to a time schedule.

1 (off) or 2 (on). The display flashes the entered

selection. Press ƒ and the display shows the new setting for the selected schedule.

Attach Schedules To Events

Outputs (065xnn where nn = Schedule number [0 to 15] and x = output number [1 to 6] minus 1)

(Defaults = off) This setting lets you attach outputs to a time schedule. Onboard outputs are 1–2, SnapCard outputs are 3–

Note

Outputs can only be scheduled if text has been entered in installer programming. Only onboard and SnapCard outputs can be scheduled.

To Attach Schedules to Outputs:

1. Press

2. Press

3. Press

4. Press

A or B until the display shows ATTACH SCHED-

ULES TO EVENTS.

ƒ then A or B until the display shows OUTPUTS.

Press ƒ to enter the OUTPUTS menu.

A or B until the desired output appears. ƒ and the display shows SCHEDULE 00 OFF/ON

(current setting). If you want a different schedule, press

Attach Schedules To Events

A or B until the desired schedule appears.

5. Press

6. Repeat steps 3, 4, and 5 until all desired outputs are

Arming (0660nn where nn = Schedule number [0 to 15])

(Defaults = off) This setting lets you arm according to a time schedule.

To Attach Schedules to Arming:

1. Press

2. Press

3. To select arm to AWAY press

4. Press

1 (off) or 2 (on). The display flashes the entered

selection. Press ƒ and the display shows the new setting for the selected schedule.

attached to schedules.

Attach Schedules To Events

A or B until the display shows ATTACH

SCHEDULES TO EVENTS.

ƒ then A or B until the display shows ARMING.

ƒ.

ƒ and the display shows SCHEDULE 00 OFF/ON

(current setting). If you want a different schedule, press

A or B until the desired schedule appears.

5. Press

6. Repeat steps 4 and 5 until all desired schedules are

1 (off) or 2 (on). The display flashes the entered

selection. Press for the selected schedule.

attached.

ƒ and the display shows the new setting

To Attach Schedules to Lights:

1. Press

2. Press

3. Press

4. Press

A or B until the display shows ATTACH SCHED-

ULES TO EVENTS.

ƒ then A or B until the display shows LIGHTS.

Press ƒ

to enter the LIGHTS menu.

A or B until the desired light appears. ƒ and the display shows SCHEDULE 00 OFF/ON

(current setting). If you want a different schedule, press

A or B until the desired schedule appears.

5. Press

6. Repeat steps 3, 4, and 5 until all desired lights are

1 (off) or 2 (on). The display flashes the entered

selection. Press ƒ and the display shows the new setting for the selected schedule.

attached to schedules.

DRAFT 8/17/00

Page 55

Programming the Panel

Note

Energy Saver Menu

The ENERGY SAVER menu lets you set the energy saver module low- and high-setpoints. These setpoints determine when the module relay closes, thereby completing the circuit through the thermostat to the furnace/air-conditioner.

Low Setpoint

(Energy Saver)

(070)

(Default = 50°F) This setting determines the temperature at which the energy saver module relay closes to activate the furnace.

Note

The low setpoint cannot be set equal to or higher than the high setpoint.

To set the Low Setpoint:

1. With the display showing ENERG Y SAVER, press

ƒ, then

A or B until the display shows LOW SETPOINT nn

DEGREES (current setting).

2. Enter the desired temperature (45–89°). The display

flashes the entered setting. Press

ƒ and the display shows

the new setting.

High Setpoint

(Energy Saver)

(071)

(Default = 90°F) This setting determines the temperature at which the energy saver module relay closes to activate the airconditioner.

Note

The high setpoint cannot be set equal to or lo wer th an the low setpoint.

To set the High Setpoint:

1. With the display showing ENERG Y SAVER, press

ƒ, then

A or B until the display shows HIGH SETPOINT nn

DEGREES (current setting).

2. Enter the desired temperature (46–90°). The display

flashes the entered setting. Press

ƒ and the display shows

the new setting.

Attach Lights to Sensors Menu

The ATTACH LIGHTS TO SENSORS menu lets you assign a light number to a sensor. Each time the sensor is activated, the attached light will turn on for 5 minutes. When the 5 minute timer expires the light will turn off. If the same light is scheduled, it will only turn on during the schedule time.

Light x to Sensor Y

(Attach Lights to Sensors)

(08n where n = light number [1–9] minus 1)

(Default = 0) This menu attaches light x to sensor y. Each time a selected sensor is tripped, the selected light will turn on and a 5 minute timer will start.

The sensor must be l earned into the curre nt p artition before it can be attached.

To attach a light to a sensor:

1. With the display showing LIGHT 1 TO SENSOR y (cur- rent setting), press

A or B to select the desired light

number.

2. Enter the desired sensor number (01–76). The display flashes the entered setting. Press

ƒ and the display shows

the new setting.

3. Repeat steps 1 through 2 until all desired lights are attached to sensors.

To detach a light from a sensor:

1. With the display showing LIGHT 1 TO SENSOR y (cur- rent setting), press

A or B to select the desired light

number.

2. Enter 0 as the sensor number and press

ƒ.

System Version Menu

The SYSTEM VERSION menu lets you view and identify panel hardware and software. This information is primarily used for troubleshooting purposes.

System Version (010 = factory code, 011= system number, 012= system level)

(Default = N/A) This menu lets you view and identify panel hardware and softw a re version.

DRAFT 8/17/00

To view and identify the System Version:

1. Press

2. Press

A or B until the display shows SYSTEM VERSION. ƒ and the disp l ay shows FACTORY CODE

nnn✱nnnn.

3. Press

4. Press

B and the disp l ay shows SYSTEM NUMBER

✱nnnnnnn.

B again and the display shows SYSTEM LEVEL

nnnn.

Page 56

Testing the System

Downloader Programming

The panel can be programmed remotely using ToolBox. Use the information you recorded in Appendix A to inform the downloading operator of the programming requirement for this system.

ToolBox Downloader Programming

Note

A Downloader Phone Number must be programmed and the user-programmable option “Downloading” must be on for remote downloader programming to work.

To initiate a ToolBox download session:

1. Contact your download station and ask the operator to prepare to download to the panel.

2. Make sure the system is disarmed.

3. Press

If the alphanumeric touchpad does not display SYSTEM DOWNLOAD IN PROGRESS, call the downloader operator to verify the downloader phone number. Also, make sure ToolBox is set up properly. Refer to the “Troubleshooting” section if the problem persists.

(down), or 2 (up). The display shows SYSTEM DOWNLOAD IN PROGRESS during the d ownloading process.

+ system master code + 7 +

0 (any), 1

Table 8. Basic Touchpad Operating Commands

Command System Response

1 + CODE Disarms system to OFF 2 + CODE Arms system to STAY 3 + CODE Arms system to AWAY 2 (quick arm on) Arms system to STAY 3 (quick arm on) Arms system to AWAY 2 or 3 + CODE + 4

or 2 or 3 + 4

5 + 2 or 3 + CODE or 5 + 2 or 3

7 + 1 Turns chime feature on and off 7 + 2 Turns Energy Saver on and off 7 + 6 Identifies alarms in memory 7 + 7 + n

(n = output number [1–6])

1–2 = onboard outputs 3–6 = module outputs

8 + CODE + 2 Initiates a phone test 8 + CODE + 3 Initiates a sensor test 8 + installer CODE + 3 Initiates a dealer sensor test

Makes entry/exit doors instant (4 must be pressed within five seconds of arming)

Arms system silently (no arming status beeps)

Turns the output on or off. (This command is only functional after output text is entered into panel memory.)

Testing the System

This section describes the following:

❑ Basic System Commands ❑ T esting Zones/Sensors ❑ Tes ting Phone Communication ❑ Testing Central Station Communication ❑ Testing Outputs and Sirens ❑ Tes ting Light Control ❑ Tes ting the Energy Saver Module ❑ Changing Fixed Disp lay Touchpads ❑ Testing the Audio Verification Module

You should test the system after installing or servicing and after adding or remo vi ng devices from the system.

Refer to the “Troubleshooting” section if correct test results are not achieved.

Basic System Commands

Table 8 describes the basic touchpad operating commands. For complete details on system operation, including user programming, refer to the system User’s Manual.

Table 8. Basic Touchpad Operating Commands

Command System Response

✱

(STATUS) Indicates current system status

✱

+ ✱ Indicates AC power and

battery status

Testing Zones/Sensors

Test sensors/zones after all programming is completed, whenever there is a change in environment, equipment, or programming, and whenever a zone- or sensor-related problem occurs.

If the system does not respond as describe d in the following procedure, see the “Troubleshooting” section.

Note

While the sensor t est is a valuable in sta llation and service tool, it only tests sensor operation for the current conditions. You should perform a sensor test after any change in environment, equipment, or programming.

1. Place all sensors and zones in their non-alarm state.

2. At an alphanumeric touchpad, enter the sensor test mode by pressing one beep and displays SENSOR TEST. The panel starts a 15 minute timer.

3. Trip each zone/sensor one at a time. Touchpads (and interior sirens) should sound one short, high-pitched beep and the display should show the sensor name (or number) and OK.

Note

If you hear a long, low-pitched beep, proceed to the following section “If a Wireless Sens or D oe s Not Test.”

4. Press the STATUS button when you think all zones/sen- sors are tested. The touchpad displays any untested sensors/zones and touchpad panics. If all sensors/zones and touchpad panics have been tested, the display shows SEN- SOR TEST OK.

5. Test any untested zones/sensors and touchpad panics.

8 + installer code + 3. The touchpad sounds

DRAFT 8/17/00

Page 57

Testing the System

CAUTION

Note

6. The system stays in sensor test mode for 15 minutes. When less than 5 minutes remain, touchpads and interior sirens beep and the panel announces the remaining time over the speakers once every minute. After 15 minutes the panel disarms to OFF, automatically. If you need more time to complete the sensor test, press

8 + installer code

+ 3 while the system is still in sensor test mode. This restarts the 15 minutes of test time.

7. When all sensors/zones and touchpad panics have been tested, press

1 + installer code to exit sensor test mode.

If a Wireless Sensor Does Not Test

If touchpads displa y SENSOR FAILURE and sirens sound a long, low-pitched beep when a zone or sensor is tripped, this indicates that the wireless sensor signal strength is below acceptable limits. Distance from the receiver, the installation environment, or both, are most likely affecting the sensor signal strength.

When possible, locate wireless sensors within 100 feet of the panel. While a transmitter may have a range of 1,000 feet or more out in the open, the environment at the installation site can have a significant effect on transmitter range. Refer to the “Troubleshooting” section to resolve the problem.

For wireless sensors that don’t respond, use an ITI RF Sniffer (60-401) test tool to verify that the sensor is transmitting. Constant beeps from the RF Sniffer indicate a runaway (faulty) sensor. Remove the sensor battery(s) and replace the sensor.

Testing Central Sta ti on/Pa ger Communication

After performing sensor and phone tests, check that the system is reporting alarms successfully to the central station or pager.

Be sure to contact the central mon itoring station activating outputs that trigger from an alarm condition.

To test communication with the central station/ pager:

1. Call the central station and tell the operator that you will be testing the system.

2. Arm the system.

3. Test each of the touchpad and wireless panic buttons and trip at least one sensor of each type (fire, intrusion, etc.) to verify correct operation.

4. Check pag er displays to verify reports are received. Pagers display an event code, digit sensor number, and the

last four digits of the account number. For example, a pager display of

999 002 7468

indicates the following: 999 = alarm condition 002 = sensor/zone in alarm or user number 7468 = last four digits of account number

before

Testing Phone Communication

Perform a phone test to check the phone com munication between the panel and the central monitoring station.

CAUTION

Be sure to contact the central mon itoring station activating outputs that trigger from an alarm condition.

To perform a phone test:

1. Contact the central monitoring station to inform them that you are testing the system.

2. Press

8 + system master code + 2.

The display reads PHONE TEST and the touchpad sounds one beep. When the panel completes the test, the system returns to the previous arming level automatically.

If the display continues to show PHONE TEST for 1½ minutes or more, enter

1 + system master code and refer to the

“Troubleshooting” section.

before

The way information is displayed varies with pager services and may not match the example above. Account numbers with alpha-characters also vary when displayed, d epending o n pager se rvice. Acc ount numbers are not displayed if STREAMLINING is turned on.

Table 9 describes pager system event codes.

Table 9. Pager System Event Codes

Code System Event

009 Zone Restoral

111 System Disarmed 115 Sensor Test Exit 118 Trouble condition cleared 119 Alarm Canceled 222 System Armed to STAY 333 System Armed to AWAY 555 Phone/Sensor Test 888 System Trouble Condition 999 System in Alarm

DRAFT 8/17/00

Page 58

Testing the System

T able 10 describ e s p a ger se nsor/zone numbe r an d use r n um be r report codes.

Table 10. Pager Sensor/Zone and User Number Codes

Code Sensor/Zone or User Number

000 System event not caused by a zone or user

–

001

076 Sensor/Zone Numbers 1–76

–

659 Regular User Codes 0–59 used

600

678 System Master Code used 679 Installer Code used 680 Dealer Code used 697 Quick Arm used 698 Keyswitch Sensor used 699 System Armed Itself (during service or

power-up)

5. When you finish testing the system, call the central monitoring station to verify that the alarms were received.

Testing Outputs and Sirens

Testing Light Control

Test all lights plugged into X-10 Lamp Modules to verify house code and light number settings.

To test light control:

1. Press 0 + 0 together.

2. Press

3. Repeat step 2 for remaining lights (

repeatedly to turn all lights on and off

0 + 1 re peatedly to turn light 1 on and off.

0 + 2 or light 2, 0 +

3 for light 3, etc.).

4. Arm the system to Away. All lights plugged into modules set to Unit 1 (or set as entry lights) should turn on and stay on for 5 minutes. All lights plugged into modules set to Unit 2 should blink three times to indicate the arming level. Remaining lights should not be affected.

5. Disarm the system. If Unit 1 (or entry) lights were on for an entry or alarm, they will turn off in 5 minutes. Unit 2 lights should blink once to indicate the system is off. Remaining lights should not be affected.

6. All lights should turn on and remain on during fire and auxiliary/medical alarms. All lights should flash during a police or intrusion alarm.

Testing the Energy Saver Module (ESM)

All outputs (onboard and SnapCard) should be tested to verify configuration programming.

CAUTION

Be sure to contact the central monitoring station activating outputs th at trigger from an alarm condition.

before

To test outputs:

1. Contact the central monitoring station to inform them you are testing the system.

2. Verify that all wiring at the panel and output devices is correct.

3. Activate the ap propriate device to trigger each output as programmed.

4. Verify that each output responds according to the programmed configuration number. For outputs that trigger sirens, verify the correct alarm sounds are produced from these sirens. Table 11 describes the system alarm sounds you should hear for each alarm event.

5. Contact the central monitoring station when you are finished testing.

Table 11. Alarm Types and Sounds

Alarm Type Alarm Sound

Fire Repeating series of three beeps Police/Intrusion Continuous tone Auxiliary Rapid beeps

Test th e Energy Saver Module to verify it overrides the thermostat.

Note

The system must have high- and low-temperature limits set to test the Energy Saver Module.

To test the Energy Saver Module:

1. Press ‚ (status) + ‚ (status) to display the system status,

ENERGY SAVER OFF, and the present TEMPERATURE nn°. The temperature displayed (and/or announced)

should match the house thermostat. If the temperatures do not match, refer to the ACCESSORY MODULES—BUS DEVICES menu in the “Programming” section.

2. Press

3. Press

7 + 2 to turn on the ESM. The display shows

ENERGY SAVER ON

and the ESM relay will click once.

7 + 2 again to turn the ESM off. The display

shows ENERGY SAVER OFF.

Note

There is a 5-minute delay after the Energy Saver Module returns control to the furnace/AC bef ore it will o v erride the furnace/AC again.

Note

If the red ESM LED is not flashing continuously, remove panel AC and backup battery power. Verify that all wiring is correct.

DRAFT 8/17/00

Page 59

Testing the System

Changing Fixed Display LCD Touchpad Chime and Trouble Beep Tones

The frequency (pitch) of chime and trouble beep tones from a fixed display touchpad can be adjusted to a more d e si rable or distinct tone, or to compensate for hearing impaired persons.

Note

Chime and trouble beep tones sound using the default frequency during, or within 15 seconds of, any button activity at that specific touchpad.

To change status tone pitch:

1. Press and hold the ‚ and 0 buttons together until you hear a steady tone, then release the buttons.

2. Press and hold raise the pitch.

3. Release the button wh en the desired pitch is heard.

After about 15 seconds of no touchpad activity, the steady tone stops soundi ng.

1 to lower the pitch or press and hold 2 to

Testing Audio Verification Module (AVM) Communication

To test the module from the central station:

1. Inform the central station that you will be sending an alarm and testing an AVM.

2. Give them the programming selections you made for the panel (see “Audio Verification Menu” on page44 for programming infor mation).

3. Use a touchpad panic button to initiate an auxiliary alarm.

4. The centr al station operator waits for the alarm to be reported and initiates an audio session.

5. Walk through the vicinity of the AVM while speaking at a normal conversation level.

6. Have the o perator speak to you.

7. When testing is complete, the operator will end the session.

Test the Audio Verification Module from off-site and the central station to verify that it works properly.

To test the module from off-site:

You will need a helper and touch-tone phone at an off-site location to perform this test. When testing the AVM from off-site the following guidelines must be followed.

❑ The Remote Access feature must be set to on (default)

(page 32).

❑ The Audio Verify feature must be set to on (page 44). ❑ The system must be in a non-alarm state. ❑ Optional Ring/Hang/Ring feature (page 33) must be on

(default) to work with steps 1 and 2 below. Otherwise wait for 12 rings and the panel will pick up automatically.

1. The off-site helper calls the panel, lets the phone ring twice, and hangs up.

2. The helper must call the panel again in 10 to 40 seconds. The panel answers System hello.

3. The helper dials the following on the phone:

# # AVM access CODE *

4. The helper should now be able to hear you through the AVM.

5. Walk through the vicinity of the AVM while speaking at a normal conversation level.

6. Tell the helper to dial a 1 and speak to you. To return to listen mode, the helper dials a 3.

7. When testing is complete, have the helper dial 99 and hang up.

DRAFT 8/17/00

Page 60

Testing the System

DRAFT 8/17/00

Page 61

Troubleshooting

This section describes what to do if you experien ce problems with system operation. If after performing the troubleshooting procedures the panel still malfunctions, please call Technical Support at 1-800-777-2624.

Topics are divided into separate tables for easy reference.

❑ Table 1, “Panel Power,” on page 62 ❑ Table 2, “Access Codes,” on page 63 ❑ Table 3, “Arming and Disarming,” on page 63 ❑ Table 4, “Bypassing ,” on page 64 ❑ Table 5, “Wireless Sensor and Touchpad Batteries,” on

page 64

❑ Table 6, “Central Station/Pager Reporting,” on page 64 ❑ Table 7, “Alphanumeric Touchpads,” on page 65 ❑ Table 8, “Fixed Display Touchpads,” on page 65 ❑ Table 9, “Speakers,” on page 65 ❑ Table 10, “Sirens,” on page 66 ❑ Table 11, “Supervised Wireless Sirens,” on page 66 ❑ Table 12, “Hardwire Zones,” on page 66 ❑ Table 13, “Wireless Sensor Zones,” on page 67 ❑ Table 14, “Wireless Touchpads,” on page67 ❑ Table 15, “Phones,” on page 68 ❑ Table 16, “Light Control,” on page 68 ❑ Table 17, “Energy Saver Module,” on page68

Troubleshooting

DRAFT 8/17/00

Page 62

Troubleshooting

Table T1: Panel Power

Problem Action/Solution

Panel does not power up. Touchpads don’t display or respond.

1. Ver ify that the panel transform er is plugged into an unswitched outlet.

2. Check the AC circuit breaker to be sure the circuit is live.

3. Check that the backup battery is installed correctly and the AC power transformer is plugged in.

4. Check for proper panel and transformer wiring.

5. Measure the incoming AC voltage at panel terminals 1 and 2. It should read about 24 VAC.

No incoming AC voltage at panel terminals 1 and 2.

Touchpad display indicates System Low Battery or voice sounds “System low battery.”

After pressing

STATUS

the touchpads flash AC or display AC Power Failu re/AC Failur e . (Panel continues to operate from backup battery.)

1. Unplug the AC power transformer and disc onnect the wires from the transformer and the panel.

2. Check transformer to panel wire for short or open circuits.

3. Plug in the transformer and check for 24 VAC at the transformer unconnected terminals. If zero (0) volts, replace the tran sformer.

1. Check that the backup battery is installed correctly and the AC power transformer is plugged in.

2. Measure the incoming AC voltage at the panel terminals 1 and 2. It should read about 24 VAC.

3. Check for 11.75 to 13.5 VDC battery voltage between the backup battery spade lugs. If the battery voltage is

within this range,

not

replace the battery.

Note

When the panel is running a backup battery test, the reading at the connected battery can range from 11.2 to 13.5 VDC. The panel automatical ly runs a backup ba ttery test under the f ollowing conditions: (1) on initi al power-up, (2) during us er s ens or te st , (3) once ev ery minute when bac kup battery has f ailed, (4 ) once e very 24 hours at the programmed STIME (UL 98 Options off) or once every 4 hours (UL 98 Options on).

Note

With the AC power transformer plugged in, the panel automatically charges the battery. While the battery is charging for the first time it is normal for the system to indicate This can take a number of hours depending on the initial battery charge. Once the battery reaches 12.5 VDC (full charge as measured while in battery test), the condition clears. If the trouble condition persists after 24 hours, replace the backup battery.

System Low Battery

1. Check the AC circuit breaker to be sure the circuit is live.

2. Check for proper panel and transformer wiring.

3. Check that the transformer is plugged into a nonswitched outlet and secured with the provided screw.

4. Check that the transformer is supplying AC to the panel. (T ransformer internal fuse may be blown.

WARNING

Be careful when securing the tran sformer to an outlet with a metal cover. Hold the cover tightly in place. You could receive a serious shock if the meta l outlet co ver dr ops do wn onto the prongs of the p lug w hil e you are securing the trans former and cover to the outlet box.

DRAFT 8/17/00

Page 63

Table T2: Access Codes

Problem Action/Solution

Customer cannot remember access code(s).

Troubleshooting

1. Check your records to see if you have the customer’s access code(s) on file.

2. Verify the access code(s) using the Downloader.

3. Clear memory and repr ogram the panel locally.

Installer cannot remember install code.

Installer cannot remember dealer code

1. Check your records to see if you have the install code on file.

2. Ver ify the install code using the Downloader.

3. Use the Dealer Code to enter program mode and view the installer

1. Check your records to see if you have the dealer code on file.

Table T3: Arming and Disarming

Problem Action/Solution

System protests and won’t arm.

System won’t disarm .

1. If arming to level 2, make sure all monitored perimeter doors and win-

2. If arming to level 3, make sure all perimeter and interior sensors are

3. Press

1. Disarming using incorrect code. Enter correct co de.

2. Access code is not programmed or set up in user programming to dis-

3. Wireless touchpad is not learned into system or hardwire touchpad is

4. The installer code is being used to disarm the system. The system is

code.

dows are closed. closed.

STATUS

arm system. not communicating to panel. Check installer programming for learned

wireless touchpads. designed

tem master code to disarm the system.

for an indication of the problem.

not to disarm

using the installer code. Use a regular or sys-

DRAFT 8/17/00

Page 64

Troubleshooting

Ta ble T4: Bypassing

Problem Action/Solution

Touchpad indicates Invalid and/or “Invalid” is heard when you attempt to bypass a sensor

1. Attempting to bypass a 24-hour sensor that cannot be bypassed (group 26 fire sensors).

2. Sensor is not active in the current arming level.

System cancels sensor bypass when you try to arm to level 2 or 3

1. Sensor is being bypassed before arming to 2—STAY or 3—AWAY. Arm to the desired level before bypassing a sens or.

Table T5: Wireless Sensor and Touchpad Batteries

Problem Action/Solution

System indicates Sensor/Touchpad nn low battery.

1. Replace the indicated device battery. Test the sensor/touchpad after replacing the battery.

Note

If the sensor/touc hpad is n ot tested a fter battery replac ement, the system conti nues to show a low battery condition, since that was the last signal it received from the device. Testing the sensor/ touchpad with new batteries allows the panel to receive a signal with good battery information.

Table T6: Central Station/Pager Reporting

Problem Action/Solution

Central station/pager is not receiving reports.

1. Check that the premises phone line is working.

2. Perform a phone test.

3. Check that the DB-8 cord is plugged into the RJ-31X/CA-38A jack.

4. Check that the DB-8 cord is wired correctly to the panel.

5. Check for correct phone line wiring between the TELCO block and RJ-31X/CA-38A jack.

6. Replace faulty RJ-31X/CA-38A jack.

7. Replace faulty DB-8 cord.

8. Verify that central station/pager phone number is programmed into the panel. Reprogram the phone number and retes t , i f necessary.

9. Verify that the correct phone format (SIA or CID) is being used.

10. For pagers, extend the pager delay setting (see the PHONE OPTIONS—GLOBAL menu in the “Programming” sectio n.

DRAFT 8/17/00

Page 65

Table T7: Alphanumeric Touchpads

Problem Action/Solution

Display shows all ************.

1. Touchpad is not connected to panel bus terminals or is wired incorrectly. Check and correct wiring.

Troubleshooting

Display is blank.

1. Check that panel is powered up.

2. Check for touchpad power and/or bus miswiring, opens, or shorts.

3. Check touchpad brightness setting (see the user-programming

OPTIONS

Touchpad buttons don’t beep when pressed.

1. Check for touchpad power and/or bus miswiring, opens, or shorts.

2. Check that key beeps option is set to on (see the

ULES—BUS DEVICES

Ta ble T8: Fixed Display Touchpads

Problem Action/Solution

Display is lit but does not respond to key presses.

Display is blank.

Touchpad buttons don’t beep when pressed.

1. Touchpad is not connected to panel bus terminals or is wired incorrectly. Check and correct wiring.

1. Check that panel is powered up.

2. Check for touchpad power and/or bus miswiring, opens, or shorts.

3. Check touchpad brightness setting (see the user-programming

OPTIONS

1. Check for touchpad power and/or bus miswiring, opens, or shorts.

2. Check that key beeps option is set to on (see the

ULES—BUS DEVICES

menu in the “Programming” section).

ACCESSORY MOD-

menu in the “Programming” section).

ACCESSORY MOD-

menu in the “Programming” section).

Table T9: Speakers

Problem Action/Solution

Speakers don’t sound alarms.

DRAFT 8/17/00

1. Check for correct wiring at speaker and panel terminals; correct where necessary.

2. Speaker output has shut down because panel detected terminal 7 or 8 is shorted to ground. Disconnect panel AC and battery backup power. Locate short and correct. Apply panel AC and backup battery power and retest.

3. Alarm is in partition 2 and speaker is connected to panel terminals 7 and 8, which activate only for partition 1 alarms.

Page 66

Troubleshooting

Ta ble T10: Sirens

Problem Action/Solution

Piezo sirens connected to Snap Card, or onbo ard (panel) outputs 1 and/or 2 don’t produce any alarm sounds.

1. Check for incorrect wiring between siren and panel; correct where necessary.

2. Output has not been confi gured (set up) to activate si rens. Enter program mode and configure output (see

DEVICES—SNAP CARD

the “Programming” section).

Table T11: Supervised Wireless Sirens

Problem Action/Solution

Sirens don’t produce any sounds and LED doesn’t respond.

Siren only works part of the time and/or at odd, irregular intervals.

1. Check to make sure siren is not plugged into an outlet controlled by a switch. Move siren to a nonswitched outlet location and test.

2. Panel doesn’t have a Power Line Carrier (PLC) card installed. Install PLC card.

3. Panel is not powered by a power line carrier transformer. Replace existing transformer with a power line carrier transformer.

4. Power transformer and sirens are not plugged into outlets on the same electrical phase. Relocate sirens at different outlets to determine working locations.

5. Siren is programmed with incorrect partition house code. Clear siren house code by pre ss ing and holding siren button for 20 se conds. Reprogram with correct partition house code and retest. See “Installing Supervised Wireless Sirens (6 0- 73 6- 95 )” on pa ge15 for more inf or mation.

6. Siren house code is not programmed int o panel. Enter program mode and set SWS and partition house codes.

1. Check that siren and/or panel transformer is not plugged into an outlet shared with a major appliance, television, or computer which may generate noise and degrade the line carrier signal.

, or

ONBOARD OPTIONS—OUTPUT 1, 2

ACCESSORY MODULES—BUS

Ta ble T12: Hardwire Zones

Problem Action/Solution

System doesn’t go into alarm when zone is tripped.

Zone reports trouble condition.

1. System is disarmed. Arm system and then trip the zone.

2. Zone is not learned into panel memory. Enter installer/dealer program mode—LEARN SENSORS, and learn zone into memory.

3. Zone is learned into wrong partition. Delete zone and learn into correct partition or change the partition in the EDIT SENSORS menu.

4. For HIM zones, check that the HIM LED is blinking to verify communication with the panel. If LED is off, check wiring between HIM and panel.

1. Check that onboard HIM and SnapCard zone inputs have a 2k-ohm EOL resistor installed at the last device on the loop in series for N/C loops, in parallel for N/O loops.

2. Check for zone wire fault—short circuit on N/C loops, open circuit on N/O loops.

3. Make sure all devices on zone are in non-alarm state, then enter disarm command to reset zone.

DRAFT 8/17/00

Page 67

Table T13: Wireless Sensor Zones

Problem Action/Solution

System doesn’t respond (in sensor test or when armed) when sensor is tripped.

1. Verify that receiver antennas are installed and connections are secure.

2. Check that the wireless sensor battery(s) are installed.

3. Check the sensor battery(s) for low voltage. Replace battery(s), if necessary.

4. Use an RF Sniffer (60-401) to verify that sensor is transmitting.

5. Sensor is not lea rned into panel memo ry. Enter installer/dealer program mode—LEARN SENSORS, and learn sensor into memory.

6. Zone is learned into wrong partition. Delete zone and learn into correct partition or change the partition in the EDIT SENSORS menu.

Troubleshooting

Sensor reports troubl e condit io n.

Touchpad indicates [senso r #] supervisory and/ or Sensor [sensor #] supervisory is heard.

Smoke sensor beeps once every minute.

Table T14: Wireless Touchpads

1. Sensor tamper switch is tripped—sensor cover is off, not latched securely, or sensor is not mounted securely. Secure sensor mounting and/or cover, then trip sensor to clear the condition.

2. Check the sensor battery for low voltage. Replace batteries, if necessary.

1. Use an RF Sniffer (60-401) to verify that sensor is transmitting. If sensor is not transmitting, check battery for low or no voltage and replace.

2. Change mounting position of sensor (from horizontal to vertical or vice versa) and test sensor several times for consistency.

3. Sensor signal is not reaching panel/receiver because sensor is too far away. Remove sensor from mounted location and test from other locations. Mount sensor in area where signal can reach panel/receiver.

1. Sensor batteries are getting low. Replace batteries.

Note

System Sensor sm ok e s enso rs (m odel 2100AR FT) d on’t tr ansmi t a low battery signal to the panel/receiver until battery voltage drops to within a range of 4.7 to 5.4 VDC. The sensor sounds beeps to notify occupants that the sensor battery(s) need replacing, but the sensor does not transmit a low battery signal to the panel until the next supervisory signal (69 minutes later).

Problem Action/Solution

System doesn’t respond to commands entered from wireless touchpad.

Touchpad reports trouble condition.

DRAFT 8/17/00

1. Verify that receiver antennas are installed and connections are secure.

2. Check that touchpad battery(s) are properly installed.

3. Check the touchpad battery(s) for low voltage . Repl ace battery(s), if necessary.

4. Use an RF Sniffer (60-401) to verify that touchpad is transmitting.

5. Touchpad is not learned into panel memory. Enter program mode and learn touchpad into memory (see LEARN SENSORS).

6. Touchpad is learned into wrong partition. Delete touchpad and learn into correct partition or change the partition in the EDIT SENSORS menu.

1. Check the touchpad battery(s) for low voltage . Repl ace battery(s), if necessary.

Page 68

Troubleshooting

Table T15: Phones

Problem Action/Solution

Loss of dial tone at on-site phones after wiring RJ-31X jack or connecting the DB-8 cord.

1. Wait 2 minutes and try agai n. The panel may be busy t ryi ng to report to the central station.

2. Disconnect the panel DB-8 cord from the RJ-31X jack. If the phone still doesn’t work, the system is okay and the problem is in the wiring.

3. Check RJ-31X jack wiring and TELCO block wiring. Replace RJ-31X jack if necessary.

4. Check DB-8 cord connections at the panel and RJ-31X jack. Replace cord if necessary.

5. Perform a phone test after troubleshooting the phone line.

Constant dia l tone, preventing dial-out on premises phones.

Table T16: Lig ht Control

Problem Action/Solution

Light controlle d by X-10 Lamp Module is not working.

1. One or more polarity-sensitive phones exist on-site. Reverse the phone wires connected to the brown and gray wire terminals on the RJ-31X jack.

1. Check that the lamp has a working bulb and that the lamp switch is on.

2. Check to make sure X-10 module is not plugged into an outlet controlled by a switch. Move to a nonswitched outlet location and test.

3. Panel doesn’t have a Power Line Carrier (PLC) card installed. Install PLC card.

4. Panel is not powered by a power line carrier transformer. Replace existing transformer with a power line carrier transformer.

5. Power transformer and X-10 modules are not plugged into out lets on the same electrical phase. Relocate modules or transformer to different outlets to determine working locations.

6. Check that the HOUSE dial on the X-10 module matches the partition house code programm ed i nto the panel.

7. X-10 module is located in wrong partition. Move module to correct partition and retest.

8. Partition house codes are not programmed into panel. Enter program mode and set partition house codes.

Table T17: Ener gy Saver Module

Problem Action/Solution

Module does not respond to system commands or appear to control furnace.

Module temperature does not match act ual room temperature.

1. Check that the module is wired correctly to the panel terminals.

2. Ver ify the module LED is flashing continuously. If the LED is not flashing, remove power and check wiring.

3. There is a 5-minute delay after the module returns control to the furnace/AC thermostat, before the module overrides the thermostat again. Wait 5-minutes and try again.

1. The module room temperature setting has not been adjusted or was adjusted before the module warmed or cooled to room temperature. To ensure accuracy, wait at least 30 minutes after installing the module, before adjusting the temperature. To adjust the module room temperature setting, see

ULES—BUS DEVICES—UNIT-ID—ENERGY OPTIONS

section “Programming the Panel.”

TEMPERATURE

under the

ACCESSORY MOD-

menu in the

DRAFT 8/17/00

Page 69

Appendix A: System Planning Worksheets

Customer Name _________________________________ Address _______________________________________ City _________________ County ___________ State ___ Zip __________ Phone (____) ______ _____

Table A.1 Wireless Devices

Part No. Description Qty.

60-362 Door/Window Sensor 60-670 SAW Door/Window Sensor

60-741-95 Micro Recessed Door/Window

60-499 Slim Line Door/Window Sensor

60-688 Micro Door/Window Sensor

60-641 Long-Life Door/Window Sensor 60-461* Shock Sensor 60-459* Sound Sensor (ITI) 60-462* Glass Guard Sensor

60-506 Smoke Sensor

60-460 Rate-of-Rise Heat Sensor 60-589* Manual Fire Pull Sensor 60-504* Freeze Sensor

60-452 Pendant Panic Sensor

60-458 Single Button Panic Sensor

60-457 Dual Button Panic Sensor

60-578 Water-Resistant P anic Sensor

60-511 DS924i PIR Motion Sens or

60-639-95R SAW Indoor PIR Motion Sensor

60-639-

95R-OD

60-703-95 Crystal Indoor PIR Motion Sensor 60-834-95 FlexGard Sound Senso r

60-597 HiTech Handheld Wireless Touch-

60-607 2-Button Keychain Touchpad

60-606 4-Button Keychain Touchpad

60-659-95 SAW 4-Button Keychain Touchpad

Sensor

SAW Outdoor PIR Motion Sensor

(Not for intrusion protection)

pad

Table A.2 Hardwire Devices

Part No. Description Qty. mA

(Max.)

Hardwire Sensors/Detectors

13-068 Magnetic Contact

13-070 Magnetic Contact –

N/A System Sensor models

13-082 PIR Motion Detector 10 mA

Sirens

60-736* Supervised Wireless

60-483-01Slim Line Hardwire

13-046 Hardwire Exterior

SuperBus 2000/Miscellaneous Components

60-746-012x16 LCD Alphanu-

60-820 Fixed English LCD

60-803 2x20 LCD Alphanu-

60-804 2x20 VFD Alphan u-

60-777-01Phone Interface/Voice

60-76401-95R

60-755 Power Line C a rrier

60-756 4 Inp ut/2 Output Snap-

60-757 8Z Hardwire Zone

60-758 4 Output SnapCard 130 mA 60-774 Hardwire Input Module 18 mA 60-770 Hardwire Output

60-620-01Energy Saver Module 20 mA

3/8” press fit

surface mount

2100D, 2100TD, 2100S, 2100TS, 2400, or 2400TH or ESL series 429AT, 521B or 521BXT

Siren

Interior Siren

Siren

meric Touchpad

Touchpad

meric Touchpad

Module RF Receiver 30 mA

Card

Expander SnapCard

Module

N/A

10 mA

N/A

120 mA

145 mA

90 mA

30 mA

120 mA

600 mA

110 mA

185 mA

230 mA

91 mA

SubTot

DRAFT 8/17/00

60-677* Interrogator 200 Audio

Total power consumption using 30 VA tran sfor mer and 4.0 AH backup battery not to exceed:

Total power consumption using 50 VA tran sfor mer and 7.0 AH backup battery not to exceed:

These devices not listed, in vestigated, or verified by UL.

†

Listed, but not tested for compatibility by UL.

Verificati on Mo du l e

Total power consumption: mA

10 mA

1,000 mA 2,000

Page 70

Appendix A: System Planning Worksheets

Module

No. RF Zone

Bus ID

Number

01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42

Table A.3 Zone and Sensor Assignments

Module

Input

Group Partition Zone/Sensor Text

Number

DRAFT 8/17/00

Page 71

No. RF Zone

43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76

Module

Bus ID

Number

Table A.3 Zone and Sensor Assignments

Module

Input

Group Partition Zone/Sensor Text

Number

Appendix A: System Planning Worksheets

DRAFT 8/17/00

Page 72

Appendix A: System Planning Worksheets

Table A.4 System Settings Index and Record

Setting (reference)

default

Installer Programming—8 + Installer/Dealer CODE + 00 24 Hour Tamper (p. 37) Off 06000 AC Failure (p. 38) Off 06010 Access Timeout (p. 45) 90 sec 0904 Account No. (p. 25) 00000 0010, 0020 1_____________

Activity Timeout (p. 34) 24 hrs 0305 Alarm Verify (p. 41) Off 06108, 06208 1_____________

Audio Mode (p. 44) 1 0901 Audio Verify (p. 44) Off 0900 Auto Phone Test (p. 31) Off 02001 Auto Stay Arming (p. 26) On 0014, 0024 1_____________

Auto Test Reset (p. 31) On 02002 Auxiliary Panic (p. 36) On 0511, 0521 1_____________

AVM Access Code (p. 45) None 0906 Back In Service (p. 37) On 06002 Backup (p. 28) CS Phone 1 On,

CS Phone 2-3 Off

Battery Restoral (p. 38) Off 06005 Beep Delay (p. 45) 2 sec 0905 Buffer Control (p. 37) Off 06001 Buffer Full Report (p. 38) Off 06006 Bypass Reports (p. 37) Off 06003 CS Phone 1-3 (p. 27) None 0100, 0110, 0120 1_____________

Call Wait Cancel (p. 32) None 02009 Cancel Message (p. 32) On 02007 Closing Reports (p. 39) Off 06101, 062 01 1_____________

Comm. Failure (p. 31) On 02003 Daylight Saving (p. 35) On 0306 Dealer Code (p. 25) None 0002 Delete Sensors (p. 44) None 082 Dial Tone Detect (p. 32) On 020 10 Dialer Abort (p. 31) On 02005 Dial Abort Delay (p. 32) 30 sec 02006 Disable Trouble Beeps (p. 41)

Off Downloader Code (p. 25) 12345 0000 Downloader Phone No. (p. 30)

None DTMF Dialing (p. 31) On 02004 Duress Code (p. 27) None 0017, 0027 1_____________

Shortcut

Setting

No.

2_____________

0105, 0115, 0125 1_____________

0701

0180

2_____________ 3_____________

2_____________

Setting (reference)

default

Duress Option (p. 40) Off 06104, 06204 1_____________

Edit Sensors (p. 44) None 08 3 Entry Delay (p. 35) 32 sec 0310, 0320 1_____________

Entry Lights (p. 36) none 0400, 0410 1_____________

Exception Reports (phones) (p. 28) Off

Exception Reports (pagers) (p. 29) Off

Exit Delay (p. 35) 64 sec 0311, 0321 1_____________

Exit Extension (p. 26) On 0013, 002 3 1_____________

Extended Delay (p. 35 ) 4 mi n 0312, 0322 1_____________

Fire Panic (p. 36) On 0510, 0520 1_____________

Fire Shutdown (p. 44) Off 0902 Force Armed (p. 40) Off 06105, 06205 1_____________

Global Fire (p. 42) Off 0704 High Level Reports (phones)

(p. 28) CS Phone 1 On, CS Phone 2-3 Off

Freeze Alarm (p. 40) Off 06107, 06207 1_____________

High Level Repo rts (pagers) (p. 29) On

House Code (p. 36) 1B, 2C 0401, 0411 1 _____________

Immediate Beeps (p. 41) Off 0700 Installer Code (p. 25) 4321 0001 Keychain TP Arming (p. 37)

Off Keyswitch Sensor (p. 26) None 0015, 0025 1 _____________

Keyswitch Style (p. 27) Transition

Latchkey Reports (page rs) (p. 30) On

Latchkey Format (p. 40) Off 06106, 06206 1_____________

Latchkey Zones (p. 36) None 0500 Learn Sensors (p. 43) None 080

Shortcut

Setting

No.

2_____________

0103, 0113, 0123 1_____________

0133, 0143, 0153, 0163, 0173

0101, 0111, 0121 1_____________

0131, 0141, 0151, 0161, 0171

0513, 0523 1_____________

0016, 0026 1_____________

0135, 0145, 0155, 0165, 0175

2_____________ 3_____________

1_____________ 2_____________ 3_____________ 4_____________ 5_____________

2_____________

2_____________ 3_____________

2_____________ 1_____________

2_____________ 3_____________ 4_____________ 5_____________

2_____________

2_____________ 1_____________

2_____________ 3_____________ 4_____________ 5_____________

2_____________

DRAFT 8/17/00

Page 73

Appendix A: System Planning Worksheets

Table A.4 System Settings Index and Record

Setting (reference)

default

Line Fail Delay (p. 33) None 0213 Local Phone Control (p. 32) On 0210, 0220 1_____ ________

Low CPU Battery (p. 37) On 06004 Low Level Reports (phones)

(p. 28) CS Phone 1 On, CS Phone 2-3 Off

Low Level Reports (pagers) (p. 29) Off

Next Phone Test (p. 34) 7 days 0303 No Activity (p. 39) Off 06103, 06203 1_____________

Open/Close Reports (phones) (p. 29) Off

Open/Close Reports (pagers) (p. 29) Off

Opening Reports (p. 39) Off 06100, 06200 1_____________

Onboard Output 1 (p. 49) 01614- any audible alarm

Onboard Output 2 (p. 49) 01710 - status & alarm tones

Output Trip Time (p. 34) 4 sec 0304 Pager Delay (p. 32) 15 sec 02008 Pager Partition Assignment

(p. 30) 1

Pager Phone 1-5 (p. 29) None 0130, 0140,

Phone Access Key (p. 33) # 0216, 0226 1_____________

Phone Panic (p. 33) Off 0215, 0225 1_____________

Phone Test (p. 30) On 02000 Phone Test Freq. (p. 34) 7 days 0302 Police Panic (p. 37) On 051 2, 0522 1_____________

Program Reporting (p. 39) O ff 06015 Quick Arm (p. 26) Off 0011, 0021 1_____________

Quick Exit (p. 26) On 0012. 0022 1_____________

Receiver Failure (p. 38) Off 06011

Shortcut

Setting

No.

2_____________

0102, 0112, 0122 1_____________

0132, 0142, 0152, 0162, 0172

0104, 0114, 0124 1_____________

0134, 0144, 0154, 0164, 0174

11101

11111

0137, 0147, 0157, 0167, 0177

0150, 0160, 0170

2_____________ 3_____________

1_____________ 2_____________ 3_____________ 4_____________ 5_____________

2_____________

2_____________ 3_____________

1_____________ 2_____________ 3_____________ 4_____________ 5_____________

2_____________

1_____________ 2_____________ 3_____________ 4_____________ 5_____________

2_____________

Table A.4 System Settings Index and Record

Setting (reference)

default

Recent Closings (p. 39) On 06102, 06202 1_____________

Remote Access (p. 32) On 0211, 0221 1_____________

RF Low Battery Rpt (p. 38) Weekly

RF Superisory Rpt (p. 39) Weekly

RF TX Timeout (p. 34) 12 hrs

Ring/Hang/Ring (p. 33) On 0212, 0222 1_ ____________

Reporting Format (SIA/CID) (p. 28) CID

Sensor Text (p. 43) None 081 Silent Talkback (p. 45) Off 0903 Siren Timeout (p. 35) 4 min 0313, 0323 1____ _________

Siren Verify (p. 42) Off 0710 Smoke Verify (p. 48) Off 1100 SnapCard Output 1 (p. 47)

(01400 - keychain touchpad * button activation )

SnapCard Output 2 (p. 47) (00410 - any audible ala rm )

SnapCard Output 3 (p. 47) (00903 - arming to STAY or AWAY)

SnapCard Output 4 (p. 47) (01003 - arming to AWAY)

Star Is No Delay (p. 37) Off 0514, 0524 1___________ __

Streamlining (p. 30) On 0136, 0146,

Supervisory Time (p. 34) 03:00 0300 Swinger Limit (p. 39) 1 06014 SWS Code (p. 42) 003 0703 System Tamper (p. 41) Off 06109, 062 09 1_____________

Toll Saver (p. 33) On 0214, 0224 1_____________

TP Panic RPT FMT (p. 38) Off 06 009 Two Trip Error (p. 38) Off 06008 Two Wire Smoke (p. 48) Off 1101 UL 98 Options (p. 41) Off 0702 Zone Restorals (p. 38) Off 06007

Shortcut

Setting

No.

2_____________

06012

06013

0301

2_____________

0106, 0116, 0126 1_____________

2_____________ 3_____________

2_____________

101001

101011

101021

101031

2_____________ 1_____________

0156, 0166, 0176

2_____________ 3_____________ 4_____________ 5_____________

2_____________

DRAFT 8/17/00

Page 74

Appendix B: Reference Tables

Table B.1 Sensor Group Characteristics

No. Name Application Alarm Delay Restoral Supervisory CS

00 Fixed Panic 24-hour audible fixed emergency buttons. Police Instant

01 Portable

Panic

02 Fixed Panic 24-hour silent fixed emergency buttons. Silent Instant

03 Portable

Panic

04 Fixed

Auxiliary

05 Fixed

Auxiliary

06 Portable

Auxiliary

07 Portable

Auxiliary

08 Special Intru-

sion

09 Special Intru-

sion

10 Entry/Exit

Delay

11 Entry/Exit

Delay

12 Entry/Exit

Delay

13 Instant

Perimeter

14 Instant

Interior

15 Instant

Interior

16 Instant

Interior

17 Instant

Interior

18 Instant

Interior

19 Delayed

Interior

20 Delayed

Interior

21 Local Instant

Interior

22 Local

Delayed Interior

23 Local Instant

Auxiliary

24 Local Instant

Auxiliary

25 Local Special

Chime

24-hour audible portable emergency buttons. Police Instant

24-hour silent portable emergency buttons. Silent Instant

24-hour auxiliary sensor, such as Pendant Panic or holdup button.

24-hour auxiliary emergency button. Siren shutoff confirms CS report.

24-hour portable auxiliary alert button. Auxiliary Instant

24-hour portable auxiliary button. Siren shutoff confirms CS report.

Special belongings, such as gun cabinets and wall safes.

Entry and exit doors that require a standard delay time.

Garage doors and entrances that require an extended delay time.

Driveway gates and entrances that require a twice extended delay time.

Exterior doors and windows. Police Instant

Interior doors. Police Follower

Interior PIR motion sensors.

Interior doors. Police Follower

PIR motion sensors.

PIR motion sensors subject to false alarms. * †Police Follower

Interior doors that initiate a delay before going into alarm.

PIR motion sensors that initiate a delay before going into alarm.

24-hour local alarm zone protecting anything that opens and closes.

Same as group 21, plus activation initiates a delay before going into alarm.

24-hour local alarm zone protecting anything that opens and closes. ‡

24-hour local alarm zone protecting anything that opens and closes. Sirens shut off at restoral.

Notify the user when a door is opened. Sounds emit from a local annunciator.

(Note: If using a PIR motion sensor, use only ITI part no. 60-511.)

* *

Auxiliary Instant

Police Instant

Police Standard

Police Extended

Police Twice

Police Follower

Police Standard

Police Instant

Police Standard

Auxiliary Instant

Special Chime

Extended

Instant

√ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √ √

√ √ √

√ √ √ √ √ √ √ √

√ √

√ √ √ √

√ √

√ √ √ √

√ √

√

Report

√

√ √

Chime

(Level 1

only)

Active

Levels

1, 2, 3

2, 3

1, 2, 3

DRAFT 8/17/00

Page 75

Appendix B: Reference Tables

Table B.1 Sensor Group Characteristics

No. Name Application Alarm Delay Restoral Supervisory CS

26 Fire 24-hour fire, rate-of-rise heat, and smoke

27 Output

Module

28 Output

Module

29 Auxiliary Freeze sensor. Auxiliary Instant

33 Siren Wireless Siren Supervision.

34 Gas Carbonmonoxide (CO) Gas Detectors

35 Local Instant

Police (Day Zone)

Note:

Check marks (

This group is not certified as a primary protection circuit for UL-listed systems and is for supplementary use only.

†

Sounds instant police siren if two or more sensors are tripped within 4 minutes. Otherwise sensors are followers to delayed

sensors. Hardwire Output Module (HOM) lamp

control or other customer feature. HOM, PIR motion sensor, sound sensor, or

pressure mat.

‡

Local alarm in levels 1 and 2. Report to CS in level 3.

√

) represent characteristics present in a group.

Fire Instant

Silent Instant

Auxiliary Instant

‡

Police Instant

√ √ √ √ √

√

√ √

√ √ √ √ √

Report

√

(level 3 only)

Chime

(Level 1

only)

1, 2, 3

sensors. If Alarm Verification is on, group 18 functions like group 17.

‡

This group has not been investigated by UL.

§ This group is required for UL-listed residential fire alarm applications.

Active Levels

DRAFT 8/17/00

Page 76

Appendix B: Reference Tables

Table B.2 Sensor Text and Item Numbers

001—Aborted 047—Detector 002—AC 048—Dining 003—Access 049—Disarmed 004—Active 050—Door 005—Activity 051—Down 006—Alarm 052—Download 007—All 053—Downstairs 008—AM 054—Drawer 009—Area 055—Driveway 010—Arm 056—Duct 011—Armed 057—Duress 012—Arming 058—East 013—Attic 059—Energy Saver 014—Auxiliary 060—Enter 015—Away 061—Entry 016—Baby 062—Error 017—Back 063—Exit 018—Bar 064—Exterior 019—Basement 065—Factory 020—Bathroom 066—Failure 021—Battery 067—Family 022—Bedroom 068—Father’s 023—Bottom 069—Feature 024—Breezeway 070—Fence 025—Building 071—Fire 026—Bus 072—First 027—Bypass 073—Floor 028—Bypassed 074—Force 029—Cabinet 075—Foyer 030—Canceled 076—Freeze 031—Car 077—Front 032—Carbon Monoxide 078—Furnace 033—Central 079—Gallery 034—Chime 080—Garage 035—Closed 081—Gas 036—Closet 082—Glass 037—Closing 083—Goodbye 038—Code 084—Hallway 039—Computer 085—Heat 040—Control 086—Hello 041—Date 087—Help 042—Daughter’s 088—High 043—Degrees 089—Home 044—Delay 090—House 045—Den 091—In 046—Desk 092—Install

093—Interior 139—Pool 185—0 094—Intrusion 140—Porch 186—1 095—Invalid 141—Power 187—2 096—Is 142—Press 188—3 097—Key 143—Program 189—4 098—Kids 144—Progress 190—5 099—Kitchen 145—Quiet 191—6 100—Latchkey 146—Rear 192—7 101—Laundry 147—Receiver 193—8 102—Left 148—Report 194—9 103—Level 149—RF 195—A 104—Library 150—Right 196—B 105—Light 151—Room 197—C 106—Lights 152—Safe 198—D 107—Living 153—Schedule 199—E 108—Load 154—Screen 200—F 109—Loading 155—Second 201—G 110—Low 156—Sensor 202—H 111—Lower 157—Service 203—I 112—Main 158—Shed 204—J 113—Master 159—Shock 205—K 114—Mat 160—Side 206—L 115—Medical 161—Siren 207—M 116—Memory 162—Sliding 208—N 117—Menu 163—Smoke 209—O 118—Mother’s 164—Son’s 210—P 119—Motion 165—Sound 211—Q 120—No 166—South 212—R 121—North 167—Special 213—S 122—Not 168—Stairs 214—T 123—Now 169—Stay 215—U 124—Number 170—Supervisory 216—V 125—Off 171—System 217—W 126—Office 172—Tamper 218—X 127—OK 173—Temperature 219—Y 128—On 174—Test 220—Z 129—Open 175—Time 221— (space) 130—Opening 176—To 222 —’(apostrophe) 131—Panic 177—Touchpad 223— - (dash) 132—Partition 178—Trouble 2 24— _ (underscore) 133—Patio 179—Unbypass 225— * 134—Pet 180—Unit 226— # 135—Phone 181—Up 227— : 136—Please 182—West 228— / 137—PM 183—Window 229— ? 138—Police 184—Zone

DRAFT 8/17/00

Page 77

Appendix C: Reference Tables

Table C.1 System Event Trigger Numbers

System Event Description Trigger

Null Trigger (used for direct control)

Fire Alarm When Fire sirens are

Police Alarm When Police sirens are

Auxiliary Alarm When Auxiliary sirens are

Any Audible Alarm When any of the abov e

Silent Alarm (sensor groups 2, 3, and duress)

Activated only by schedule or direct comm an d.

started.

sirens are started.

When a sensor in group 2 or 3 goes into alar m or when a duress alar m is activated (does not include groups 25, 27, 28, or 32).

000

001

002

003

004

005

No.

Table C.1 System Event Trigger Numbers

System Event Description Trigger

No.

Interior Siren Activation follows all sys-

tem noises

AVM Trip (pulse) When an AVM alarm

occurs, output is deacti vated for 10 ms

Ready LED Follows the s tate of the

FDT green LED

Tamper Condition When any tamper is tripped 020

Closing Report Sent When a closing report has

been successfully transmitted to the cen tra l station.

Group XX in Alarm When any sensor in group

XX goes into alarm

Sensor XX in Alarm When sensor number XX

goes into alarm

Sensor XX Open When sensor number XX is

opened

017

018

019

021

see Table C.2

see Table C.3

Any Audible or Silent Alarm

HOM Group 27, 28, 32 in Alarm

Major Trouble (phone or receiver failure)

Arming to STAY or AWAY

Arming to AWAY When the panel is arme d to

AVM is Interactive (audio session in progress)

Fail-to-Communicate (panel can’t call CS or pager)

AVM Trip (edge) When an AVM alarm

Keychain Touchpad Star Button-Press

Smoke Power (for resetting 4-wire smoke detectors)

Exterior Siren Activated for police or fire

When any alarm is started (does not include groups 25, 27, 28, or 32).

When a sensor in group 27, 28, or 32 goes into alarm.

When a receiver failure (S94) or a phone failure (S96) occurs.

When the panel is arme d to level 2 or 3.

level 3.

When the centra l s t ation operator begins listening or talking to the premises.

When the fail-to-com municate output is activated.

occurs, output is activa ted momentarily.

When the star button on a keychain touchpad is pressed.

Deactivated w hen hardwire smoke detectors need to be reset.

alarms.

006

007

008

009

010

011

012

013

014

015

016

Table C.2 Sensor Group Event Trigger Numbers

Sensor Group Trigger

No.

Group 00 in alarm 064

Group 01 in alarm 065

Group 02 in alarm 066

Group 03 in alarm 067

Group 04 in alarm 068

Group 05 in alarm 069

Group 06 in alarm 070

Group 07 in alarm 071

Group 08 in alarm 072

Group 09 in alarm 073

Group 10 in alarm 074

Group 11 in alarm 075

Group 12 in alarm 076

Group 13 in alarm 077

Group 14 in alarm 078

Group 15 in alarm 079

DRAFT 8/17/00

Page 78

Appendix C: Reference Tables

Table C.2 Sensor Group Event Trigger Numbers

Sensor Group Trigger

No.

Group 16 in alarm 080

Group 17 in alarm 081

Group 18 in alarm 082

Group 19 in alarm 083

Group 20 in alarm 084

Group 21 in alarm 085

Group 22 in alarm 086

Group 23 in alarm 087

Group 24 in alarm 088

Group 25 in alarm 089

Group 26 in alarm 090

Group 27 in alarm 091

Group 28 in alarm 092

Group 29 in alarm 093

Table C.3 Sensor Number Event Trigger Numbers

Sensor

Number

Sensor 12 in alarm 140 open 268

Sensor 13 in alarm 141 open 269

Sensor 14 in alarm 142 open 270

Sensor 15 in alarm 143 open 271

Sensor 16 in alarm 144 open 272

Sensor 17 in alarm 145 open 273

Sensor 18 in alarm 146 open 274

Sensor 19 in alarm 147 open 275

Sensor 20 in alarm 148 open 276

Sensor 21 in alarm 149 open 277

Sensor 22 in alarm 150 open 278

Sensor 23 in alarm 151 open 279

Sensor 24 in alarm 152 open 280

Sensor 25 in alarm 153 open 281

State Trigger

No.

State Trigger

No.

Group 32 in alarm 096

Group 33 in alarm 097

Group 34 in alarm 098

Group 35 in alarm 099

Table C.3 Sensor Numbe r Event Trigger Numbers

Sensor

Number

Sensor 01 in alarm 129 open 257

Sensor 02 in alarm 130 open 258

Sensor 03 in alarm 131 open 259

Sensor 04 in alarm 132 open 260

Sensor 05 in alarm 133 open 261

Sensor 06 in alarm 134 open 262

Sensor 07 in alarm 135 open 263

Sensor 08 in alarm 136 open 264

Sensor 09 in alarm 137 open 265

Sensor 10 in alarm 138 open 266

Sensor 11 in alarm 139 open 267

State Trigger

No.

State Trigger

No.

Sensor 26 in alarm 154 open 282

Sensor 27 in alarm 155 open 283

Sensor 28 in alarm 156 open 284

Sensor 29 in alarm 157 open 285

Sensor 30 in alarm 158 open 286

Sensor 31 in alarm 159 open 287

Sensor 32 in alarm 160 open 288

Sensor 33 in alarm 161 open 289

Sensor 34 in alarm 162 open 290

Sensor 35 in alarm 163 open 291

Sensor 36 in alarm 164 open 292

Sensor 37 in alarm 165 open 293

Sensor 38 in alarm 166 open 294

Sensor 39 in alarm 167 open 295

Sensor 40 in alarm 168 open 296

Sensor 41 in alarm 169 open 297

Sensor 42 in alarm 170 open 298

Sensor 43 in alarm 171 open 299

Sensor 44 in alarm 172 open 300

Sensor 45 in alarm 173 open 301

Sensor 46 in alarm 174 open 302

DRAFT 8/17/00

Page 79

Table C.3 Sensor Number Event Trigger Numbers

Appendix C: Reference Tables

Sensor

Number

Sensor 47 in alarm 175 open 303

Sensor 48 in alarm 176 open 304

Sensor 49 in alarm 177 open 305

Sensor 50 in alarm 178 open 306

Sensor 51 in alarm 179 open 307

Sensor 52 in alarm 180 open 308

Sensor 53 in alarm 181 open 309

Sensor 54 in alarm 182 open 310

Sensor 55 in alarm 183 open 311

Sensor 56 in alarm 184 open 312

Sensor 57 in alarm 185 open 313

Sensor 58 in alarm 186 open 314

Sensor 59 in alarm 187 open 315

Sensor 60 in alarm 188 open 316

Sensor 61 in alarm 189 open 317

Sensor 62 in alarm 190 open 318

Sensor 63 in alarm 191 open 319

Sensor 64 in alarm 192 open 320

Sensor 65 in alarm 193 open 321

Sensor 66 in alarm 194 open 322

Sensor 67 in alarm 195 open 323

Sensor 68 in alarm 196 open 324

Sensor 69 in alarm 197 open 325

Sensor 70 in alarm 198 open 326

Sensor 71 in alarm 199 open 327

Sensor 72 in alarm 200 open 328

Sensor 73 in alarm 201 open 329

Sensor 74 in alarm 202 open 330

State Trigger

No.

State Trigger

No.

Table C.4 System Feature Event Trigger Numbers

Feature State Trigger

No.

Phone Test initiated 225

AC Failure for 15

CPU Low Battery detec t ed (e xcluding first

Auto Phone Test begun 228

Receiver Failure detected 229

Back In Service alarm (AC loss, battery

Phone Failure detected 231

Buffer Full detected 232

Two Trip Error detected 2 33

System Tamper alarm (40 incorrect code

Freeze alarm 237

No Activity alarm 238

Fire Panic alarm 239

Police Panic alarm 240

Auxiliary Panic alarm 241

Opening Report occurred 2 42

Closing Re po rt occurred 243

Latchkey Opening or Closing

Duress alarm 245

Force Armed Report occurred 246

Fire in Partition alarm 247

Recent Closing Repo rt occurred 2 48

Sensor Test entered 249

minutes

minute after power- up)

drain, then AC res tore)

entry keystrokes)

occurred 244

226

227

230

236

Sensor 75 in alarm 203 open 331

Sensor 76 in alarm 204 open 332

DRAFT 8/17/00

Page 80

Appendix C: Reference Tables

Table C.5 Response Characteristics

Response

Description

Characteristics

Momentary trip time The point wil l remain activated for nn

3 minute trip time The point will remain ac ti v a te d for 3

Siren-time trip time The point will remain activated while the

Sustained trip time The point will rema in activated for the

Siren pattern The point will activa te and deactivate

Trip delay The point will activate 30 seconds after the

seconds (n is 1-12 seconds). The default is 4 seconds

minutes

interior siren is sounding

duration of the event

according to the current alarm type: Auxiliary -- fast on/off/on

Police -- constant on Fire -- repeating)

trigger event occu rs

Table C.6 Response Numbers

Siren

Tracking

no no momentary 00 no no

no no no no no no no no

yes

Trip

Delay

yes

yes no momentary 08

no no no

yes

Response

Time

3 minutes siren time sustained

momentary 04 3 minutes

siren time sustained

3 minutes siren time sustained

momentary 12 3 minutes

siren time sustained

01 02 03

05 06 07

09 10 11

13 14 15

Response

No.

Notes for Table C.6 Response Numbers

1. If an event does not trigger sirens, siren tracking response numbers activate without turning on the output. If sirens are triggered by another event, the ou tput pulses to match the siren.

If the siren cadence changes (from polic e to fire, for example), outputs set up for siren tracking change to match the siren and all pulsing outputs pulse to one common cadence.

Note

The mechanical lifetime of the relay ma y b e exceeded if an output is set up for a siren tracking response and a pulsing siren (auxiliary or fire) is active for long time periods. A SnapCard relay output’s lifetime expectancy is about 350 total pulsing hours.

2. If an event does not trigger sirens, siren time response times activate outputs only if sirens are active for another reason.

3. If an alar m event does not necessarily require disarming (no activity, closing report, etc.), outputs set up for a sustained response time remain activated until the next arming level change.

4. If an event o ccurs that activates an output set up for trip delay, the delay and output activation can be canceled by trigger event restoral.

Note

The trip delay i s f ac tory set f o r 30 se conds and c annot be changed.

5. Activated outputs set up for a 3-minute response time remain active for the entire three minutes. To deactivate the output before the 3-minute time expires, you must enter program mode or remove panel power.

Activated outputs set up for a momentary or 3-minute response time restart if the same trigger event occurs again.

DRAFT 8/17/00

Page 81

Programming Mode Menus and Settings

To enter Programming Mode:

8 + Installer or Dealer Code + 0 + 0

Programming Mode Menus and Settings

TIER 1 MENUS

System Programming

Demo Kit

Off

Partition 1 Copy

Clear Memory

Exit Programming

TIER 2 MENUS

Security

Global

Downloader

Code

0000

Installer Code

4321

0001

Dealer Code

✲ ✲ ✲ ✲

0002

12345

Partition 1

Account

00000

Number

0010

BABA

Quick Arm

Off

0011

BABA

Quick Exit

On Off

0012

Exit Extension

On Off

0013

Auto Stay Arming

On Off

0014

Keyswitch

Sensor

0015

Keyswitch Style Transition State

0016

Duress Code

✲ ✲ ✲ ✲

0017

Partition 2

Account

00000

Number

0020

Quick Arm

Off

0021

Quick Exit

On Off

0022

Exit Extension

On Off

0023

Auto Stay Arming

On Off

0024

Keyswitch

Sensor

0025

Keyswitch Style Transition State

0026

Duress Code

✲ ✲ ✲ ✲

0027

Phones

CS Phone 1

Phone Number

0100

High Lev Rpts

0101

Low Lev Rpts

0102 0112

Exception Rpts

0103 0113

Open/Close Rpts On

0105

0106

On Off

Off

Backup

On Off

Reporting

Format

CID

SIA

CS Phone 2

Phone Number

0110

BABA

High Lev Rpts

0111

Low Lev Rpts

On Off

Exception Rpts

BABA

Open/Close

Rpts On

Off

0114 0104

Backup

0115

Reporting

Format

SIA

0116

Off

CID

(Continued)

CS Phone 3

Phone Number

0120

High Lev Rpts

0121

Low Lev Rpts

0122

Exception Rpts

0123

Open/Close

Rpts On

0124

Backup

0125

Reporting

0126

Notes

1. Underlined settings indicate defaults.

2. Shortcut numbers appear in the lower-left corner of each menu box, where applicable.

Off

Format SIA

Off

CID

DRAFT 8/17/00

8690G 04 A .D S F

Page 82

Programming Mode Menus and Settings

TIER 2 MENUS (cont.)

Phones (cont.)

Pager

Phone 1

Phone Number

0130

High Lev Rpts

On Off

0131

Low Lev Rpts

0132

Exception Rpts

Off

0133

Open/Close Rpts On

0134

Latchkey Rpts

On Off

0135

Streamlining

On Off

0136

Ptn Assignment

1 2

0137

Off

Phone Options

On Off

Off

Open/Close

Rpts On

Off

On Off

1 2

Pager

Phone 3

Phone Number

0150

BABABABABA

High Lev Rpts

0151

Low Lev Rpts

0152

Exception Rpts

0153

0154

Latchkey Rpts

0155

0156

Ptn Assignment

0157

Pager

Phone 2

Phone Number

0140

High Lev Rpts

0141

Low Lev Rpts

0142

Exception Rpts

0143

Off

0144

Latchkey Rpts

0145

Streamlining

0146

Ptn Assignment

0147

On Off

Off

Open/Close Rpts On

Off

On Off

Streamlining

On Off

1 2

Pager

Phone 4

Phone Number

0160

High Lev Rpts

0161

Low Lev Rpts

0162

Exception Rpts

0163

0164

Latchkey Rpts

0165

Streamlining

0166

Ptn Assignment

0167

On Off

Off

Open/Close Rpts On

Off

On Off

1 2

Pager

Phone 5

Phone Number

0170

High Lev Rpts

On Off

0171

Low Lev Rpts

Off

0172

Exception Rpts

Off

0173

Open/Close Rpts On

0174

Latchkey Rpts

On Off

0175

Streamlining

On Off

0176

Ptn Assignment

1 2

0177

Off

Downloader Phone

Phone Number

0180

Global

Phone Test

On Off

02000

Auto Phone

Test On

02001

Auto Test Reset

On Off

02002

Comm Failure

On Off

02003

DTMF Dialing

On Off

02004

Dialer Abort

On Off

02005

Dial Abort Delay 30 secs (15-120)

02006

Cancel Message

On Off

02007

Pager Delay

15 secs (0-30)

02008

Call Wait

Cancel

02009

Dial Tone Detect

On Off

02010

Partition 1

Off

Partition 2

Local Phone

Ctrl

On Off

0210

Remote Access

On Off

0211

Ring/Hang/

Ring

On Off

0212

Line Fail Delay

None (10-240)

0213

Toll Saver

On Off

0214

Phone Panic

Off

0215

Phone ACC Key

✱

0216

Local Phone

0220

Remote Access

0221

0222

0224

Phone Panic

0225

Phone ACC Key

0226

8690G 05A.D SF

Ctrl

On Off

Ring/Hang/

Ring

On Off

Toll Saver

On Off

Off

✱

DRAFT 8/17/00

Page 83

Programming Mode Menus and Settings

TIER 2 MENUS (cont.)

Timers

Global

Supervs. Time

Rndm 1:00-4:00

0300

RF Tx Timeout

12 hours (2-24)

0301

Ph. Test Freq

7 days (1-255)

0302

Next Ph. Test

7 days (1-255)

0303

Output Trip

Time

4 sec (1-12)

0304

Act. Timeout

24 hours (1-42)

0305

Daylight Sav.

On Off

0306

Partition 1

Entry Delay

32 secs (32-240

0310

Exit Delay

64 secs (48-184)

0311

Extended Delay

4 mins (1-8)

0312

Siren Timeout 4 mins (1-30)

0313

Partition 2

Entry Delay

32 secs (32-240

)

0320

Exit Delay

64 secs (48-184)

0321

Extended Delay

4 mins (1-8)

0322

Siren Timeout 4 mins (1-30)

0323

)

Light Control

Partition 1 Partition 2

Entry Lights

0400

House Code

0401

1B (1-255)

Entry Lights

0410

House Code

2C (1-255)

0411

Touchpad

Options

Global

Latchkey Zones

None (1-76)

0500

Partition 1 Partition 2

0510

Auxiliary Panic

0511

Police Panic

0512

Keychain TP Arm On

0513

Star is No Delay

0514

Fire Panic

On Off

Off

Fire Panic

On Off

0520

Auxiliary Panic

0521

Police Panic

On Off

0522

Off

Keychain TP Arm On

0523

Star is No Delay

0524

8690G 06 A .D S F

On Off

Off

DRAFT 8/17/00

Page 84

Programming Mode Menus and Settings

TIER 2 MENUS (cont.)

Reporting

Global

24 Hour Tamper

06000

Buffer Control

06001

Back in Service

On Off

06002

Bypass Reports

06003

Low CPU

Battery

06004

Batt. Restoral

06005

Buffer Full Rpt

06006

Zone Restorals

06007

Two Trip Error

06008

TP Panic RPT

FMT On

06009

AC Failure

06010

Off

On Off

Off

Partition 1

Opening Rpts

Off

06100

Closing Rpts

Off

06101

Recent Closings

On Off

06102

No Activity

Off

06103

Duress

Off

06104

Force Armed

Off

06105

Latchkey Format

Off

06106

Freeze Alarm

Off

06107

Alarm Verify

Off

06108

System Tamper

Off

06109

Receiver Fail

Off

06011

Partition 2

Opening Rpts

Off

06200

Closing Rpts

Off

06201

Recent Closings

On Off

06202

No Activity

Off

06203

Duress

Off

06204

Force Armed

Off

06205

Latchkey Format

Off

06206

BABA

Freeze Alarm

Off

06207

Alarm Verify

Off

06208

System Tamper

Off

06209

RF Low Bat Rpt

Weekly

Daily

06012

Siren Options

Global

Immediate

Beeps On

0700

Disable Trouble

Beeps On

0701

UL 98 Options

0702

SWS Supv Code

003 (1-255)

0703

Global Fire

0704

RF Supv Rpt

Weekly

Daily

06013

Off

Partition 1

0710

Swinger Limit

06014

Siren Verify

Off

1 (1-2)

Program

Reporting

06015

Sensors

Learn Sensors

080

Sensor Partition

Off

Sensor Group

Trip

Sensor

Sensor Text

081

Text for

Sensor

Sn n Item 0

Delete Sensors

082

Delete Sensor

0 -

Done

Edit Sensors

083

Sn P1 Gnn

NC/NO/TP

RF/HW

Sensor Ptn

Sensor Group

8690G 07 A .D S F

DRAFT 8/17/00

Page 85

TIER 2 MENUS (cont.)

Audio Verification

Partition 1

Audio Verify

0900

Audio Mode

0901

Fire Shutdown

0902

Silent Talkback

0903

Access Timeout

90 secs

0904

Beep Delay

2 secs

0905

Access Code

✲ ✲ ✲ ✲

0906

Change ID

Device ID

nnnnnnnn

Programming Mode Menus and Settings

Accessory Modules

SnapCards

Partition Assign

1 2

01400

Energy Options

Freeze Temp

(40°-90°F)

Temperature

(40°-90°F)

1 2

101010 101020

Configuration

00410

101011 101021 101031

42°F

Output Programming

Output 3 Output 4

Partition Assign

1 2

Configuration

00903

Outputs

Output n

Partition

Assign 1 2

Output Text

Partition Assign

1 2

101030

Configuration

01003

Output 1 Output 2

10110

Output 1

Item n

10111

Output 2

Item n

Output 3 Output 4

10112

Output 3

Item n

10113

Output 4

Item n

Unit - ID

Maximum of 16 bus devices.

Output 1 Output 2

Partition Assign

101000

Configuration

101001

Bus Devices

Off

100nn (nn=00-15)

The menus available will depend on SuperBus

device(s) installed.

Device Partition

Partition

Assign

1 2

Keypad Options

Status Beeps

On Off

Key Beeps

On Off

DRAFT 8/17/00

Configuration

✲ ✲ ✲ ✲ ✲

8690G 08 A .D S F

Page 86

Programming Mode Menus and Settings

TIER 2 MENUS

Onboard Options

Inputs

Smoke Verify

1100

Two-Wire Smk

1101

Off

Partition

11110

Configuration

11111

Assign

1 2

01710

Output Programming

Output 1 Output 2

Partition

Assign

1 2

11100

BABA

Configuration

01614

11101

Output Text

Output 1 Output 2

1120

Output 1

Item n

Press B to return

to Security Menu.

1121

8690G 09 A .D S F

Output 2

Item n

DRAFT 8/17/00

Page 87

System Wiring Notes

Note 1

Class II power transformer mu st be plug ged into an unswitched AC power r eceptacle. Do not short the transformer terminals together. The transformer contains an internal fuse that permanently disables the output if the terminals are shorted.

Note 2

An alphanumeric to uchpad is required for on-site programming.

Note 3

Speaker terminals 7 and 8 activate only for alarms in partition 1. Use speakers with an 8-ohm or higher impedance. When connecting two or more 8-ohm speakers, they must be wired in series as shown in the wiring diagram. Wiring two or more 8-ohm speakers in parallel can permanently damage the panel.

Note 4

Onboard outputs 1 and 2 are open-c ollector type rat ed for 200 mA m aximum. Output 1 defaults to configuration number 01614 (exterior siren). Output 2 defaults to configuration number 01710 (interior siren). Refer to panel installation instructions for all possible settings.

Note 5

Zone (loop) wiring shown is an example that applies to all zones (except when zone 8 is configured for 2-wire smoke detectors). Install EOL resistors across all unused zone (loop) inputs.

Note 6

For UL Listed installations, wire multiple supervised hardwi re smoke detectors (10 maximum) only as shown. Maximum 10 uA current draw per detector. Maximum 80 mA current draw in alarm.

Note 7

Some telephones are polarity-sensitive. Green and red wires may need to be reversed.

Note 8

A maximum of two Audio Verification Mod ules (60 -67 7) are allowed (partition 1 only). Wire multiple speakers in series, and power and microphone wires in parallel. Use shielded cable where shown in diagram to prevent crosstalk between the speaker and microphone. Audio Verification Modules shall not be used in UL Listed installations.

Note 9

Connect multiple piezo sirens in parallel. Slim Line Hardwire Interior Siren status volume switch settings have no effect.

Note 10

Refer to the S uperBus 2000 Energy Saver Modul e Installation Inst ructions for thermostat wiring details.

Note 11

Wire Hardwire Module zone (loop) inputs as shown fo r the panel. Install EOL resistors across all unused zo ne (loop) inputs. R efer to the Module Installation Instructions for complete details.

Page 88

NOT

USED

NOTE 5:

PIR MOTION

SENSOR 13-082

2k Ohm EOL

RESISTOR

49-454

(LOCATE AT

SENSOR)

BLACK

WHITE

GREEN

RED

1 2

3 4 5

6 10

11 12

13 14 15 16

18 19 20 21

VAC

+ 12 BUS

BUS

OUTPUT

GND

MIC.INZONE

ZONE

GND

ZONE

3GND

GND

ZONE

NOTE 3:

13-060

(15 WATT)

8 - OHM

SPEAKER

NOTE 3: 2 8-OHM

SPEAKERS

IN SERIES (16 OHMS)

SPLICE

OTE 1: CLASS II POWER

TRANSFORMER

60-761, 60-762,

60-778, or 60-779

23 24

ZONE

8 2-WIRE SMOKE

2-WIRE SMOKE

POWER

TELCO

TIP

NOTE 5:

NORMALLY

OPEN

(N/O)

CONTACTS

IN PARALLEL

2k Ohm

EOL RESISTOR

49-454

2k Ohm EOL

RESISTOR 49-454

(LOCATE AT

LAST DEVICE)

NOTE 5:

NORMALLY

CLOSED

(N/C)

CONTACTS

IN SERIES

NOTE 6: 2-WIRE

HARDWIRE

SMOKE/HEAT

DETECTOR

(10 MAXIMUM)

7 8

SPEAKER

OUTPUT

NOTE 7:

RJ-31X (CA-38A)

PHONE JACK

PHONE

CONNECTIONS

BRN

GRY

GRN

RED

GREEN

WHITE OR

YELLOW

BLACK

TELCO

PROTECTOR

BLOCK

GRN

RED

TIP

(+)

RING

(-)

RJ-31X

PHONE

LINE

WIRE

RUN

GREEN

RED

BLACK

WHITE

YELLOW

PREMISES

PHONES

GREEN

BROWN

GRAY

RED

TO PANEL

TERMINAL 4

2k Ohm EOL RESISTOR 49-454 (LOCATE AT LAST

DETECTOR)

SEPARATE

WIRE

CABLES

SPLICE

YELLOW

CABLE

SHIELD

WIRE

NOTES 3 & 8: AUDIO VERIFICATION MODULE, 60-677

DB-8

CORD

26 27

CLASS II

24 VAC

30 OR 50 VA

NOTE 2:

SUPERBUS 2000 FIXED

DISPLAY TOUCHPAD (60-820)

2X16 LCD ALPHANUMERIC

TOUCHPAD (60-746-01)

7 8

HOUSE

TIP

HOUSE

RING

TELCO

RING

ALL PANEL TERMINAL CONNECTIONS ARE CLASS II POWER LIMITED

NOTE 3: HARDWIRE INTERIOR SPEAKER 60-528

HIGH2GND

LOW

NOT USED

RED

BLACK

NOTES 4 & 9:

SLIM LINE HARDWIRE

INTERIOR SIREN

60-483-01

NOTES 4 & 9:

HARDWIRE EXTERIOR

SIREN 13-046

2 3 4 5

NOTE 10: SUPERBUS 2000 ENERGY SAVER MODULE 60-620-01

TO FURNACE

THERMOSTAT

NOTE 11: SUPERBUS 2000 8Z INPUT MODULE 60-774

NOTE 11: SUPERBUS 2000 4-RELAY OUTPUT MODULE 60-770

456

OPTIONAL SUPERBUS 2000 MODULE CONNECTIONS

PANEL TERMINALS

SYSTEM WIRING DIAGRAM

(See notes on other side.)

456

+12V

2A3B4

GND5GND6SPK17SPK28AUD19AUD210GND11TIP 112TIP 2

RING

4 5

+12V

GND BUS

GREEN

BROWN

GRAY

RED

DB-8

CORD

26 27

GRY

RED

PLUG

GRN BRN

BRN

GRY

GRN

RED

NOTE 7:

RJ-31X (CA-38A)

PHONE JACK

NOTES 3 & 7: SUPERBUS 2000 PHONE INTERFACE/VOICE MODULE 60-777-01

PANEL TERMINALS

8690G13A.DS

NOTE 4

SPEAKER

TO PANEL TERMINALS 7 & 8

PHONE INTERFACE/VOICE MODULE

TERMINALS 6 & 7

SPEAKER

12345678910111213141516

ZONE COMMON

ZONE 1

ZONE 2

ZONE 3

ZONE 4

ZONE 5

ZONE COMMON

ZONE 6

ZONE 7

ZONE COMMON

ZONE 8

NO 1

NC 1

COM 1

ZONE 1

NO 2

NC 2

COM 2

NO 3

NC 3

COM 3

NO 4

NC 4

COM 4

ZONE COM

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

(PARTITION 1

VOICE MODULE

ONLY)

Page 89

Index

Numerics 24-Hour Tamper 37 A AC Failure reports 38 Account Number 25 Activity Timeout 34 Alarm Verify 41 Attach Lights to Sensors 55 Audio Access Code 45 Audio Mode 44 Audio Verify 44 Auto Force Armed 40 Auto Phone Test 31 Auto Stay Arming 26 Auto Test Reset 31 Auxiliary Panic 36 B Back In Service 37 Backup (Central Station Phones) 28 Battery Restoral reports 38 Beep Delay 45 Buffer Control 37 Buffer Full Report 38 Bus Device Output Programming 46 Bypass Reports 37 C Call Wait Cancel 32 Cancel Message 32 central station 27 Chime On Close 53 Clear Memory 24 Closing Reports 39 codes

Partition Master 51 System Master 51, 52

user 50 COMM Failure 31 Concord

basic commands 56 D Date 50 Daylight Savings 35 Dealer Code 25 Delete Sensors 44

Demo Kit Mode 24 Device ID 46 Dial Tone Detect 32 Dialer Abort 31 Dialer Abort Delay 32 Direct Bypassing 51 Disable Trouble Beeps 41 Downloader Code 25 Downloader Phone Number 30, 56 Downloader programming 56 Downloading option in User programming 52 DTMF Dialing 31 Duress Code 27 Duress Option 40 E Edit Sensors 44 Energy Saver Menu 55 Entry Delay 35 Entry Lights, Lights Entry 36 ESM temperature 47 Exception Reports 28, 54 Exit Delay 35 Exit Extension 26 Extended Delay 35 F Fire Panic 36 Fire Shutdown 44 Force Armed 40 Freeze Alarm 40 Freeze Temperature 47 G Global Fire 42 H High Level Reports 28 High Setpoint 55 House Code 36 I Immediate Beeps 41 Installer Code 25 K Key Beeps 47 Keychain Star Is No Delay 37 Keychain Touchpad Arming 37 Keyswitch Arming 26, 27 Keyswitch Sensor 26 Keyswitch Style 27

L Latchkey Format 40 Latchkey Report 51 Latchkey Reports 30, 54 Latchkey Zones 36 Learn Sensors 43 Lights 54 Line Fail Delay 33 Local Phone Control 32 Low CPU Battery 37 Low Level Reports 28 Low Setpoint 55 M Master code 51, 52 N Next Phone Test 34 No Activity reports 39 O Onboard Output Text 49 Onboard Outputs 49 onboard outputs 58 Open/Close Reports 28 Opening Reports 39 Output 1, 2 49 Output Scheduling 54 Output Trip Time 34 P Pager Delay 32 Partition 1 Copy 24 Partition Assignment 30, 46 Partition Jump 51 Partition Master Code 51 Phone Access Key 33 phone numbers

central station 27

Downloader 30 Phone Test (on/off) 30 Phone Test Frequency 34 Police Panic 37 Program Report 39 programming

Downloader 56 programming menus

Tier 2

Accessory Modules 45 Onboard Options 48 Sensors 42

User Programming 50

Page 90

Index

Q Quick Arm 26 Quick Exit 26 R Receiver Failure reports 38 Recent Closings 39 relay outputs 47 Remote Access 32, 51 Response Numbers 80 RF Low Battery Report 38 RF Supv Report 39 RF TX Timeout 34 Ring/Hang/Ring 33 RJ-31X Phone Jack 20 S Scheduled Arming 54 Schedules 53 sensor group event trigger numbers 77 sensor number event trigger numbers 78 Sensor Text 43, 48, 49 setting the system

date 50

time 50 setting up for bypassing 51 setting up for system tests 51 SIA/CID Reporting 28 Silent Arming 52, 54 Silent Talkback 45 Siren Options 41 Siren Timeout 35 Siren Verify 42 Smoke Verify 48 Snapcard Output Programming 47 SnapCard Output Text 48 SnapCards

relay outputs 47 Star Is No Delay 37 Status Beeps 47 Streamlining 30, 57 Supervisory Time 34 Swinger Limit 39 SWS Code 42 System Date 50 system feature event trigger numbers 79

System Master Code 51, 52 System Tests 51 System Time 50 System Version 55 T Temperature 47 testing

central station/pager com-

munication 57 outputs 58 phone communication 57 the system 56 zones/sensors 56

Time 50 Toll Saver 33 Touchpad Brightness 52 TP Panic RPT FMT 38 trigger numbers 77, 78, 79 Two Trip Error 38 Two Wire Smoke 48 U Unit ID 46 User Codes 50, 51 V Voice Chime 52 Volume 52 W Wire Length 8 Z Zone Restorals 38

DRAFT 8/17/00