Page 1
$GYHQW+RPH1DYLJDWRU
6\VWHP
Document Number: 466-1318-ITI Rev. B February 2001
Contents
ITI Part No. 60-562-02, 60-562-05
Welcome ........................................................................... 1
System Features ...............................................................1
System Information ..........................................................2
Using the Touchpad Buttons .....................................2
Using Hand-held Touchpads ..................................... 4
Using Keychain Touchpads ......................................4
General Operation .....................................................4
Adjusting the Touchpad Display Brightness .............5
Adjusting the Volume of Status Messages ................5
Global Settings .................................................................6
Global Access Code ..................................................6
Area Jumping ................................................. ...........6
Global Status and History .........................................6
Access Codes .................................................. .................6
Adding an Access Code ............................................6
Guidelines ............................................................6
Deleting an Access Code ..........................................7
Listing Codes ............................................................7
Changing an Access Code ........................................7
Changing an Access Code’s Limits ..........................8
Use Limit ............................................................. 8
Day Limit .............................................................8
Permanent User ....................................................8
Changing Access Code’s Authority ..........................8
User Text ................................................................... 9
Authority Levels .............................................................. 9
Authority Level Definitions ......................................9
Changing Authority Level Definitions ...................10
Using the Phone with the System ..................................11
Accessing the System Using a Home Phone ..........11
Accessing the System During a Phone Call........11
Accessing the System Away from Home ................11
Bypassing an Answering Machine or
Voice Mail ..........................................................11
Disengaging Local Phone Control ..........................12
Adjusting the Phone Volume ..................................12
Alarms ............................................................................ 12
Manually Activating Alarms ..................................12
Preventing Accidental Alarms ................................13
Tips for Avoiding Accidental Alarms ................13
Cancelling an Alarm ...............................................13
Manually Resetting Hardwired Smoke Detectors ..........13
System Tampering ..........................................................13
Touchpad Access Code Tampering .........................13
Remote Phone Access Code Tampering .................14
Phone Line Tampering ............................................14
Equipment/Sensor Tampering .................................14
Security Protection .........................................................14
Turning Security Protection On.............................. 14
Arming to Home ................................................14
Arming to Away .................................................14
Arming to Night................................................. 15
Arming to Silent .................................................15
Bypassing ...........................................................15
Automatically Bypassing ...............................15
Manually Bypassing .......................................15
Group Bypassing ............................................15
No Delay .................. ..... ...... ...... .........................16
Silent Arming .....................................................16
Turning Security Protection Off ..............................16
Using the No Activity Feature ................................16
Using Opening and Closing Reports .......................16
Open/Close Schedules .......................................17
Opening/Closing Exception Reports ..................17
Controlling Lights and Devices .....................................17
Lights ......................................................................17
Manually Turning All Lights On or Off
at Once ...............................................................17
Manually Turning One Light On or Off ............17
Brighten or Dim Lights ......................................17
Devices (Appliances) ..............................................18
Manually Turning a Single Device On and Off .18
Chime and Latchkey Features ........................................18
Chime Feature .........................................................18
Latchkey Feature .....................................................18
Automating The System Using Schedules .....................18
Schedule Types .......................................................18
Arming Schedules ...................................................19
Sunrise/Sunset Schedules ........................................19
Weekly Schedules ...................................................19
One-Time Schedules ...............................................20
Associating Lights, Devices and Access Codes
with Schedules ........................................................21
Lights and Devices .............................................21
Controlling Lights Automatically ..................21
Controlling Devices Automatically ................22
Access Code Schedules ......................................22
System Status .................................................................22
Checking the System Status .................................... 22
What the Status or Trouble Beeps Mean .................22
Checking the Alarm History ...................................24
Viewing the History Buffer .....................................24
Maintaining Your System ...............................................24
Testing ..................................................................... 24
Automatic T est Features .....................................24
T es ting the System Manually .............................24
Page 2
Testing the Phone Connection to the
Monitoring Service..........................................24
Testing Sensors/Inputs (Zones) ......................24
Testing the Panel Backup Battery ...................24
Cleaning the System Components ..........................25
Checking and Changing Batteries ...........................25
Troubleshooting ..............................................................25
Appendix A: Planning for Emergencies .........................26
Guidelines ...............................................................26
Floor Plan Example 26
Your Floor Plan .......................................................26
Appendix B: System Menu Map ....................................28
Appendix C: Display Error Messages and Meanings .....29
Appendix D: System Planning Tables ............................31
Schedules .................................................................31
Holiday Schedules ...................................................31
Dealer Service Information
Dealer ____________________________________________
Representative ____________________________________________
Phone (______) ______–________
Fax (______) ______–________
Street Address ____________________________________________
____________________________________________
____________________
City
ZIP/Postal Code
_____________
State/Province
_________
E-mail ____________________________________________
Page 3
Welcome
Welcome
Thank you for selecting the Advent Hom e Navig ato r secu rity system! This system is designed to detect and respon d
to various security related conditions such as door/window
sensor activation, smoke/heat detector activation, and others.
The system is simple and easy to use via touchpad displays and buttons (and telephone touchpads).
The system is designed to tell you what you need to know
(when you need to know) and to ask for what it needs by
way of simple menu displays and selections. This method
of communication simplifies your job as a us er and makes
the information in the manual complete and easy to follow.
Advent is a tremendous, user-friendly system designed to
simplify your life while providing the optimum in automated security protection.
System Features
Your security system provides several options for creating
the security and control environment you need in your
home. How you use the system is up to you. Regardle ss of
the features you choose, you will find that your security
system dramatically enhances your life style.
In addition to the standard intrusion and fire system features, here are just a few of the ways you can use the special features of your security system.
1RWH
Some features of this security system are optional and
are available from your security consultant.
Automatic Lighting Control
You can control lights inside and outside of your home by
plugging them into wireless devices called lamp modules.
These lights can then be turned on and off using either the
system touchpads or your home phones. In addition, the
system automatically turns selected lights on during an
intrusion or fire. The system automatically turns selected
lights on to scare off the intruder or to help you safely
enter/exit.
Automatic Device (Appliance) Control
You can control the appliances inside and outside of your
home by plugging them into wireless appliance modules.
For example, the system can be programmed to automatically turn your coffee pot or other appliance on and off
with a schedule.
Courtesy Features
The buttons on your hardwire touchpads light up when
you first push a button and stay on for 15 second s after the
last button is pushed. This makes it easy to operate your
system in a dimly lit entrance area. You can adjust the
brightness of the display and dim the l i ght to darken a
touchpad in a bedroom while someone is sleeping. You
can also operate your system silently. Using this method,
you can arm or disarm your system quietly and without
disturbing others.
Partitions
The system can be set up by your security consultant to
operate as a multi-partition system. This way the same sys-
tem can be used to protect separ ate areas such as duplex or
quad homes, with each area having its own touchpad, sen-
sors, sirens and so forth. Your home system can operate
with up to 4 or 8 (depending on model) separate partitions.
Areas
Choose whether or not to treat partitions as areas. If treated
as areas:
q Zones, touchpads, schedules, programming options,
etc., belong to areas instead of partitions.
q Users may “jump” from one area to another area using
an alphanumeric touchpad.
q The word “partition” will be changed to “area” wher-
ever it is spoken, displayed, or printed.
q Users can display status for all areas in one operation
(Global Status).
Zone/Sensor Types
The sensors in your system are made up of different
“types,” and various sensor types react d i f f erently. Certain
sensors automatically trigger a call to the central monitor-
ing station immediately after being set off, or “tripped.”
Other sensors trigger a call to the central monitoring sta-
tion only after being tripped twice within a certain time
period. Some sensors react silently while others allow you
to set entry and exit delays. There are “local-only” sensors
that sound sirens at your home but do not send a call for
help. The following are some of the useful ways you can
use various sensor types in your home.
q Monitor “Off-Limits” Areas of the Premises - Many
areas in your home can be hazardous to children.
Using local-only sensors, you can monitor certain
areas such as liquor, gun, and medicine cabinets and
even your swimming pool. If the pool gate or monitored cabinet door is opened, a siren beeps. The beeping stops when the gate or door is closed. You can also
use this sensor type to alert you to cars approaching
your home from the driveway, to monitor your mailbox so you know when the mail arrives, and as a wir eless doorbell.
q Protect Private Business Information - You can con-
trol accessibility to private documents or money
drawers. For example, sensors could be set to beep
any time the safe door is opened during business
hours. You can also assign up to 100 or 250 (depending on model) different system access codes to users.
Then, if you choose to receive opening and closing
reports from your central monitoring station, you can
check employee arming and disarming procedures. If
your system is not properly armed, you can be called.
If normal opening procedures aren’t followed, additional people can be notified.
If your home has a security gate covering the front
door and windows, yo u may cho ose to pu t a sen sor on
the gate to sound a local siren if someone shakes the
gate to scare them away but not to call the central station. If the intruder continues to break in, other sen-
Advent® Home Navigator System
1
Page 4
System Information
sors protecting the front doo r and windows woul d call
the central monitoring station.
q Set Doors and Windows for Entry/Exit - Entry and
exit door sensors can be set to one of three delays,
depending on how accessible your doors are to your
system touchpad or Touch-Tone
®
telephone. The
delays are set to give you enough time to get in and
out of your house, but not allow an intruder to sneak
in behind you. You may want a short delay on the
door leading from the garage to the house and a little
longer delay on the overhead garage door. You can
have an even longer delay on the driveway gate.
What Happens in an Emergency?
Your security system touchpad has three panic alarms—
police, fire, and auxiliary or medical—that call for help
immediately. They are activated by pressing the appropriate touchpad buttons. Even very young children can learn
how to send for emergency help if needed. Police and fire
fighters will know the exact location and nature of the
emergency.
Your security system can also monitor the normal activity
in your home and call for help automatically if normal
activities are not detected. For example, if someone falls
and can’t move, the system notices that normal activities,
such as placing outgoing calls or opening doors and windows, have not occurred for a certain length of time. Your
system sounds a low-volume siren for 5 (programmable)
minutes to let you know there may be a problem. If all is
well, you can stop the siren by disarming your system. If
no one disarms the system during the 5 minutes, your system calls for help. Refer to Appendix A, “Planning for
Emergencies” for emergency planning details.
Using the System When You’re Away
Off-site operations using any T ouch-Tone telephone allow
you to control and monitor most of your system features
even while you are away from your home. If you are on
vacation, for example, you can turn lights and appliances
on and off, check for any trouble conditions, and even
bypass the sensor on a door to let in a neighbor, delivery
person, or service person.
System Information
You may have ins talled this security system simply to prevent break-ins and theft and t o detect f i res. H owever, your
new security system can alert you to many other emergencies. Plus, this security system lets you monitor and control conditions in your home or business even when you
are away.
To effectively use your security system, you need to develop a few simple habits:
q Check for open doors and windows before leaving.
q Remember to gather your things and then arm your
system and exit before the exit delay time expires.
q Remember to disarm your system within the entry
delay time when you return.
q Respond to beeps, light indicators, and voice
announcements from your system, which indicate the
status of your system.
You soon become aware of the benefits these few simple
habits bring you and help you incorporate your security
system seamlessly into your everyday life.
Using the Touchpad Buttons
The touchpad is the primary way to manually operate the
system or partition. Table 1 contains a list of the buttons
and what they do.
Security
Automation
Fire Protection
Access Control
A BD
POLICE
POLICE
PANIC BUTTONS -- PRESS AND HOLD BOTH BUTTONS TO ACTIVATE
C
AUXILIARY
AUX/MEDICAL
E
F
FIRE
FIRE
Figure 1. Touchpad Buttons
Security
1
Lights
4
Features
7
Undo
*
Advent System - Test Weekly
2
Devices
System
Phone
0
Access
ControlSilent Arm
3
Energy
65
Scripts
98
Enter
#
IHG
2
1 SECURITY MENU
2 SILENT ARM MENU
3 ACCESS CONTROL MENU (NOT USED)
4 LIGHTS MENU
5 DEVICES MENU
6 ENERGY MENU (NOT USED)
7 FEATURES MENU
8 SYSTEM MENU
9 SCRIPTS MENU (NOT USED)
0 PHONE MENU
MAIN MENU OR ACCEPT
PREVIOUS MENU OR QUIT
DISPLAY BRIGHTNESS
TURN ALL LIGHTS OFF
TURN ALL LIGHTS ON
8543g114b.dsf
Advent® Home Navigator System
Page 5
T able 1: Touchpad Button Descriptions
POLICE
A
B
AUXILIARY
C
D
FIRE
F
E
Undo
*
Button Description
Causes police panic alarm when both buttons are pressed and held or pressed twice.
Causes auxiliary or medical panic alarm when both buttons are pressed and held or pressed twice.
Causes fire panic alarm when both buttons are pressed and held or pressed twice.
G
Turns all controlled lights on when held or pressed twice within 2 seconds.
H
Turns all controlled lights off when held or pressed twice within 2 seconds.
System Information
I
Controls display br igh t ness w he n pr esse d and he l d.
1 Security Displays Security menu. Allows you to do security functions such as arming/disarming, bypassing, and
checking system status and alarm memory.
2 Silent Arm Displays Silent Arming menu. Provides special security functions such as silent arming/disarming.
3 Access Control
(to be developed)
Displays Access Control menu. Offers building access control functions.
4 Lights Displays Lights menu. Allows you to turn controlled lights on and off individually and assign timed light
schedules. Lights can be turned on and off all at once by pressing the touchpad Lights On and Lights Off
buttons twice.
5 Devices Displays Devi ces menu. Allo ws you to turn no n-light controlled devices s uch as fans and others on and
off and assign timed device sch edules.
6Energy
(to be developed)
Displays Ener gy menu.
7 Features Displays Features menu. Allows you to turn features such as door chime on and off. Also allows you to
add, delete, or list lights and devices, change schedules, view the event log, and jump between areas (if
used).
8 System Displays System menu. Allows you to run various system tests and adjust the voice siren volume.
9 Scripts
(to be developed)
Displays Scripts menu. Allows you to record and run automatic button-press sequences (scripts). 0 Phone Displays Phone menu. Offers phone test and data communication (downloading) functions.
Cancels current operation, if any. Also returns to the previous or Main menu.
Enter
#
Advent® Home Navigator System
Displays Main menu if system is idle. The Main menu lists all other menus. Also enters or accepts
displayed data or selection and skips to the next selection (if any).
3
Page 6
System Information
!
$
'
&
#
"
%
5 6
* ;
O F F
S T A Y A W A Y
N O D E L A Y
C H I M E
S T A T U S
B Y P A S S
POLICE
A
B
FIRE
F
E
AUXILIARY
C
D
POLICE
A
B
FIRE
F
E
AUXILIARY
C
D
Using Hand-held Touchpads
If you have a wireless hand-held touchpad (60-597-95),
you can use it as a remote control for the system.
These Hand-held
Touchp ad buttons…
O F F
S T A Y A W A Y
!
N O D E LA Y
"
#
$
C H IM E
&
%
'
S T A T U S
B Y PA S S
* ;
5 6
C O M M A N D
8543219A.DSF
Work like these
Touchpad buttons…
Security
1
Lights
2
Devices
4
Features
System
7
Undo
Phone
*
Access
ControlSilent Arm
3
Energy
65
Scripts
98
Enter
#0
Using Keychain Touchpads
If you have a two- or four-button Keychain Touchpad
(60-607-319.5, 60-606-319.5), your security consultant
has customized it to do designated system actions. You
may find i t useful to write down what the butt ons have
been set up to do.
Action Press this
button(s)…
Arm to Away (default)
_____________________________
Disarm (default) ______________
Press twice to cancel arming protests.
Turn All Lights On/Off (default)
_____________________________
Arm to next higher level (default)
_____________________________
Zone Trip (default)
_____________________________
Auxiliary Panic Alarm (default)
_____________________________
Programmable
_____________________________
8543164A.DSF
COMMAND
Action Touchpad Hand-held
Cancel an accidental alarm
Activate a police panic alarm
Activate a fire panic alarm
Programmable
_____________________________
Not Used
General Operation
G
H
Table 2: Basic System Commands
Touchpad
ACCESS CODE ACCESS CODE #, *, ACCESS CODE
In addition to automatic detection, the system also
responds to display touchpads, Touch-Tone telephones,
wireless touchpads, and other manual controls.
Table 2 shows some basic system commands and the most
common ways to perform them. F or a complet e discussi on
of these, go to the page number listed.
Press this on a…
Keychain
Home Phone See
Touchpad
__________
#, *, 8, 8, 8, 8, 8
optional
__________
#, *, 9, 9, 9, 9, 9
optional
Page
Activate an auxiliary panic
alarm
Disarm to OFF 1, 1,
4
__________
#, *, 7, 7, 7, 7, 7
optional
ACCESS CODE 1, 1, ACCESS CODE #, *, 1, 1, ACCESS CODE
Advent® Home Navigator System
Page 7
Table 2: Basic System Commands
S
Action Touchpad Hand-held
Touchpad
Arm to HOME 1, 2, ACCESS CODE 1, 2, ACCESS CODE
1, 3,
Arm to AWAY
ACCESS CODE 1, 3, ACCESS CODE #, *, 1, 3, ACCESS CODE
Press this on a…
Keychain
Touchpad
__________
optional
System Information
Home Phone See
#, *, 1, 2,
ACCESS CODE
Page
Arm to AWAY with
Latchkey
Turn all lights ON
ACCESS CODE, 8 1, 3, ACCESS CODE, 8 _________
1, 3,
Press twice
or hold for 2
seconds.
G
4, 0, #, 1
optional
Hold
#, *, 1, 3, ACCESS CODE, 8
#, *, 4, 0, #, 1
Or press 4, 0, #, 1
H
4, 0, #, 2
Hold
#, *, 4, 0, #, 2
Turn all lights OFF
Press twice
or hold.
Or press 4, 0, #, 2
Manually reset smoke
ACCESS CODE 8, 9, ACCESS CODE #, *, 8, 9, ACCESS CODE
8, 9,
sensors
View main menus or cancel
a menu operati on
Enter data
Undo
*
Enter
#
S T A T U S
5 6
B Y P A S
* ;
#, *, *
Check system status 1, 9 1, 9 #, *, 1, 9
Silence trouble beeps
Undo
*
S T A T U S
5 6
#, *, *
Check alarm history 1, 0 1, 0 #, *, 1, 0
Check event history buffer 7, 5 7, 5 #, *, 7, 5
Adjusting the Touchpad Display Brightness
Both alphanumeric touchpad VFD (blue/green) display
character brightness and LCD (yellow) display back-lighting are adjustable.
To change the display character or back-lighting brightness press and hold the touchpad button
least two seconds and then release. Momentarily you will
see it at full brightness then it stays at the next brightness
level setting. Repeat this to the desired setting or to view
each of the five brightness levels from off to bright.
I (TARGET) for at
Adjusting the Volume of Status Messages
You can change the volume of the status voice messages
from the system. There are 9 volume lev els, from 0 (silent)
to 8 (maximum).
To change the status voic e m essage volume:
Steps Response
1. Press 8, 4 (from main menu).
SYSTEM MENU; VOLUME LEVEL IS X.
TO ACCEPT PRESS # OR ENTER A
NEW LEVEL FROM 0-8 THEN PRESS
#
1RWH
Any alarm condition or button press temporarily sets the
display to fu l l brightness.
Advent® Home Navigator System
2. Enter
0 through 8 for
desired loudness and
press #.
VOLUME LEVEL IS NOW SET TO X
5
Page 8
Global Settings
1RWH
Police and Fire alarm voice messages are optionally at
full volume. Auxiliary and m edical alarms are affected
by status voice volume.
Global Settings
Global system settings specify how the entire system behaves.
Global Access Code
There are two types of codes regarding partitions/areas.
Global access codes can be used in all partitions/areas. All
other access codes belong to the partition/area in which
they were added and cannot be used to control other partitions/areas. When a touchpad is redirected to a new partition/area, any access code used must be valid in that
partition to work.
The partition/area of an access code cannot be changed.
However, the same cod e may be programmed in mo re than
one partition/area, with each instance of the code representing a unique user number. The panel does not allo w
the user to add a duplicate code within a partition/area,
globally, or a user code which is equal to the installer code.
Area Jumping
Normally, an Advent panel has partitions and no areas.
Y our security consultant can turn your partitions into areas
which then allows you to jump between areas using the
alphanumeric touchpad. Only users with global access
codes with primary or full authority can access this.
Every time a jump occurs, a 4-minute timer is started.
When this timer expires, the touchpad jumps back to its
original area automatically . Also, every time the touchpad
becomes inactive, (no menu changes) a shorter, programmable time, (default 10 seconds), starts. When this timer
expires, the touchpad jumps back to its original area automatically.
To jump between areas :
Steps Response
1. Press 7, 7 (from main
menu).
2. Enter your global ACCESS
CODE.
3. Enter the area to redirect the touchpad to.
Global Status and History
If partitions have been turned into areas, the user can also
check for global status and history. Selecting global status
allows the user to view the following:
q Arming status of all enabled areas.
q Whether any alarms are active in any enabled area.
q Whether a battery test, LED test, or download is in
progress.
FEATURES MENU; ENTER YOUR
CODE
ENTER AREA TO REDIRECT TO
THEN PRESS #; OR FOR GLOBAL
STATUS PRESS 19#; OR FOR
GLOBAL HISTORY PRESS 75#
System displays arming
status for that area.
q All current system or area troubles.
q Status of main power, main battery, and main phone
line.
To view global status:
Steps Response
1. Press 7, 7 (from main
menu).
2. Enter your global ACCESS
CODE.
FEATURES MENU; ENTER YOUR
CODE
ENTER AREA TO REDIRECT TO
THEN PRESS #; OR FOR GLOBAL
STATUS PRESS 19#; OR FOR
GLOBAL HISTORY PRESS 75#
3. Press 19, #. System displays the global
status then returns to the
main menu.
Selecting global history allows the user to view the complete contents of the event history buffer, i.e. system
events and events from all areas.
To view global history:
Steps Response
1. Press 7, 7 (from main
menu).
2. Enter your global ACCESS
CODE.
3. Press
75, #. System displays the global
FEATURES MENU; ENTER YOUR
CODE
ENTER AREA TO REDIRECT TO
THEN PRESS #; OR FOR GLOBAL
STATUS PRESS 19#; OR FOR
GLOBAL HISTORY PRESS 75#
history then returns to the
main menu.
Access Codes
The system access codes are used to limit certain system
operations to authorized personnel. Access codes are programmable and are from four to six digits long. The system will indicate if and when an access code is required to
perform any desired function. When
played, enter the access code using the touchpad buttons.
The system automatically has one access code for the primary user in each partition/area. It is the primary access
code. You can change the primary access code, but you
cannot delete it. In addition to this primary access code,
you can create secondary access codes for other users.
1RWH
If you enter access codes with a partition code, all
codes added will work for that partition. If a global code
is used, all codes added will aut om atically be global
codes.
Adding an Access Code
Add an access code to the system whenever you want
other authorized persons to have use of the system.
Guidelines
1. Do not use sequential numbers (1234, 5678, et c.) that
can be easily defeated by unauthorized users.
ENTER YOUR CODE is dis-
6
Advent® Home Navigator System
Page 9
Access Codes
2. Do not use birthdate/year combinations which others may know.
3. Do not use phone number sequences which others may know.
4. Keep a separate log of all programmed user codes and their user names in a secure location.
To add an access code:
Steps Response
1. Press 1, 8 (from main
menu).
2. Enter your primary ACCESS
CODE.
SECURITY MENU; ENTER YOUR
CODE
ACCESS CODE MENU
3. Press 1. ENTER THE NEW CODE THEN
PRESS #
4. Enter new ACCESS CODE and press #.
5. Enter new
again and press
6. Press
1RWH
No two access co des can be alike. I f you are unsuccessful adding an access code, make sure th e new
access code doesn’t al re ady exist in the system. To
check the existing co des, from the main menu select 1,
8, your
access code
#.
* twice to exit. MAIN MENU
access code, 3.
ENTER THE CODE A SECOND
TIME THEN PRESS #
CODE OK
Deleting an Access Code
Delete an access code when you no longer want that code
to allow access to the system. To ensure maximum security, delete access codes as soon as they are no longer
needed.
1RWH
A partition code cannot view gl obal codes.
To list access codes:
Steps Response
1. Press 1, 8 (from
SECURITY MENU; ENTER YOUR CODE
main menu).
2. Enter your primary
ACCESS CODE.
ACCESS CODE MENU
3. Press 3. USER # CODE XXXX NO TEXT AUTH:X LIM:X
For LIM you can have the
following options:
P = Permanent, D = Day, and
U = Use.
For AUTH, you can have the
following options:
P = Partition, F = Full, or 1-8. If
there is a * the code is a global
code.
4. Press
* twice to exit. MAIN MENU
Changing an Access Code
All access codes are not alike. When you add an access
code, you can give each access code different options.
Using the Access Code menu, you can (and should)
change the options of each new access code to ensure
maximum security.
To ensure maximum security, access codes should be
changed on a regular (monthly) basis.You should also
change an access code if you suspect an unauthorized person knows a user’s access code or if/when a user is
replaced.
To delete an access code:
Steps Response
1. Press 1, 8 (from main menu). SECURITY MENU; ENTER YOUR
CODE
2. Enter your primary ACCESS
CODE.
ACCESS CODE MENU
3. Press 2. ENTER THE CODE TO DELETE
THEN PRESS #
4. Enter the
ACCESS CODE to
CODE DELETED
delete and press #.
5. Press * twice to exit. MAIN MENU
1RWH
If you are unsuccess fu l d elet i ng an access code, make
sure the access code exists in the system. To check the
existing codes, from th e m ai n m enu select 1, 8, your
access code, 3. Also, the system will not let you delete
the primary access code or codes with equal or higher
authorities.
Listing Codes
When listing codes, the panel displays the user number,
code, user text, limits, and authority level.
To change an access code:
Steps Response
1. Press 1, 8 (from main
menu).
2. Enter your primary ACCESS
CODE.
SECURITY MENU; ENTER YOUR
CODE
ACCESS CODE MENU
3. Press 4. ENTER THE CODE TO CHANGE
THEN PRESS #
4. Enter the
change and press #.
5. Enter the new
and press #.
6. Enter the new
ACCESS CODE to
ACCESS CODE
ACCESS CODE
ENTER THE NEW CODE THEN
PRESS #
ENTER THE CODE A SECOND
TIME THEN PRESS #
CODE OK
again and press #.
7. Press
* twice to exit. MAIN MENU
1RWH
No two access codes can be alike. If you are unsuccessful adding an access code, make sure that the new
access code doesn ’t al re ady exist in the system. To
check the existing co des, from the main menu select 1,
access code, and 3.
8, your
Advent® Home Navigator System
7
Page 10
Access Codes
1RWH
1RWH
Changing an Access Code’s Limits
Use Limit
Select Use Limit when the user will only need to access
the system a limited number of times such as for testing or
service personnel.
To set a Use Limit for new access codes, first add the
access codes to the system, then follow the on-screen
menu.
To set a use limit for an exi st ing access code:
Steps Response
1. Press 1, 8 (from main menu). SECURITY MENU; ENTER YOUR
2. Enter your primary ACCESS
CODE.
3. Press
6. ENTER THE CODE TO CHANGE
4. Enter the ACCESS CODE to
change and press
5. Press
3. ENTER THE NUMBER OF USES
#.
6. Enter the desired number of
uses and press
#.
7. Press * twice to exit. MAIN MENU
When an access code wit h a U s e Li m it expires, it will
automatically be deleted.
Day Limit
Select Day Limit if a user will only need temporary access to the system, such as service personnel.
You can not set both a Day Limi t and a Use Limit for a
single access code.
To set a Day Limit for new access codes, first add the
access code to the system, then follow the touchpad onscreen menu.
To set a day limit for an existing access code:
Steps Response
1. Press 1, 8 (from main menu). SECURITY MENU; ENTER YOUR
2. Enter your primary ACCESS
CODE.
3. Press 6. ENTER THE CODE TO CHANGE
4. Enter the
ACCESS CODE to
change and press #.
5. Press
2. ENTER THE NUMBER OF DAYS
6. Enter the desired number of
days and press
#.
7. Press * twice to exit. MAIN MENU
CODE
ACCESS CODE MENU
THEN PRESS #
CODE IS SET TO XXXXXX
VALID THEN PRESS #
VALID FOR X USES
CODE
ACCESS CODE MENU
THEN PRESS #
CODE IS SET TO XXXXXX
VALID THEN PRESS #
VALID FOR X DAYS
1RWH
“Number of days” means the number of days starting
from today through the last day you want the access
code to work. The acces s code quits working and is
deleted at midnight of the l ast day.
Permanent User
All new access codes are automatically permanent unless
you set a Day/Use Limit. Select Permanent User when yo u
want the access code to work for an unlimited amount of
time or when you want to erase the Day Limit or Use
Limit of an access code.
To reset an access co de t o per m anent:
Steps Response
1. Press 1, 8 (fro m main menu). SECURITY MENU; ENTER
YOUR CODE
2. Enter your primary ACCESS
CODE.
3. Press
4. Enter the
6. ENTER THE CODE TO CHANGE
ACCESS CODE to
ACCESS CODE MENU.
THEN PRESS #
CODE IS SET TO XXXXXX
change and press #.
5. Press
1. CODE SET TO PERMANENT
6. Press * twice to exit. MAIN MENU
Changing Access Code’s Authority
Each access code can have an authority level from 0 (full)
to 8 (limited). A lower number allows the use of more features and gives the user more control. A higher number
prevents the user from using some features. See Authority
Levels for more detailed information.
To set an authority level for new access codes:
Steps Response
1. Press 1, 8 (from main
menu).
2. Enter your primary ACCESS
CODE.
3. Press
4. Enter the new
1. ENTER THE NEW CODE THEN
ACCESS CODE
and press #.
5. Enter the new
ACCESS CODE
again and press #.
6. Press 4. AUTHORITY 1. ENTER AN
7. Enter the desired authority
level and press
#.
8. Press * twice to exit. MAIN MENU
SECURITY MENU; ENTER YOUR
CODE
ACCESS CODE MENU
PRESS #
ENTER THE CODE A SECOND
TIME THEN PRESS #
CODE OK
AUTHORITY NUMBER THEN
PRESS #
CODE SET TO AUTHORITY X
8
Advent® Home Navigator System
Page 11
Authority Levels
To set an authority level for an exis ting access code:
Steps Response
1. Press 1, 8 (from main menu). SECURITY MENU; ENTER
YOUR CODE
2. Enter your primary ACCESS CODE. ACCESS CODE MENU
3. Press
4. Enter the
5. Enter the desired authority level
7. ENTER CODE TO CHANGE
ACCESS CODE to change
and press
#.
number (0-8) and press #.
THEN PRESS #
AUTHORITY X; ENTER AN
AUTHORITY NUMBER THEN
PRESS #
CODE SET TO AUTHORITY
X
6. Press * twice to exit. MAIN MENU
User Text
Each access code can have up to 20 characters of user text
assigned to it. This text is used when listing codes and
when identifying a user during event printing. User text
uses the same display tokens as static display text (see
T able 3) except that special tokens, such as time, date, and
flashing *, are not allowed.
When using user text you need to enter the whole string before pressing #.
Table 3: Two-Digit Display Descriptors
No. Token Text No. Token Text
00 0 24 H
01 1 25 I
02 2 26 J
03 3 27 K
04 4 28 L
05 5 29 M
05 6 30 N
07 7 31 O
08 8 32 P
09 9 33 Q
10 (undefined) 34 R
11 (undefined) 35 S
12 # (pound) 36 T
13 : (colon) 37 U
14 / (slash) 38 V
15 ? (question mark) 39 W
16 . (period) 40 X
17 A 41 Y
18 B 42 Z
19 C 43 _ (space)
20 D 44 ‘ (apostrophe)
21 E 45 -- (dash)
Table 3: Two-Digit Display Descriptors
No. Token Tex t No. Tok en Text
22 F 46 __ (underline)
23 G 47 * (star)
To change user text:
Steps Response
1. Press 1, 8. SECURITY MENU; ENTER YOUR CODE
2. Enter your primary
ACCESS CODE.
ACCESS CODE MENU
3. Press 0. ENTER THE CODE TO CHANGE THEN
PRESS #
4. Enter the ACCESS CODE
ENTER USER TEXT NUMBERS
to change and press #.
5. Enter the user text
ACCESS CODE MENU
numbers (from Table
3) then press
6. To check that you
typed the correct text
#.
Touchpad displays all listed
codes and their authorities.
press 3 to list codes.
Authority Levels
Each access code has an authority level which determines
the authority the user has to execute certain actions. There
are three pre-defined authorities and eight configurable
authorities.
Installer Authority - Can enter program mode (if partitions/areas are disarmed), gain remote access, do phone
test, do installer zone test, initiate a downloader call,
review status and event his t ory, control lights and de vices,
change installer code, change arming level within one hour
of exiting program mode. Cannot change schedules or
access codes (except own), bypass zones, extend arming
levels, change arming levels except as stated above.
Installer code is permanent.
Primary Authority - Primary user for that partition/area.
There is exactly one primary code per partition/area. This
code is permanent and cannot be restricted. Can do everything except enter program mode, do installer zone test,
initiate a downloader call. Primary codes are permanent.
Full Authority -
except add/delete/change/list codes of equal or higher authority.
Authority 1 to 8 - Configurable authorities. In general,
authority 1 should be the highest of the configurable authorities and authority 8 the lowest.
Authority Level Definitions
The three pre-defined and eight configurable authorities
allow you to carry out a specific set of actions which
require an access code and deny others. Whenever one of
these actions is requested from a touchpad, the panel
prompts you for an access code and determines whether
the entered code has sufficient authority. If not, the panel
responds with
Can do everything the primary user can do
INVALID AUTHORITY.
Advent® Home Navigator System
9
Page 12
Authority Levels
When using a keyfob or keyswitch to request an arming
level change, no access code is needed and the action is
associated with a zone, not a user.
Table 4: Authority Level Actions
Auth # Parameter
I P F 1 2 3 4 5 6 7 8
10 Remote Phone Access Y Y Y CY CN CN CN CN CN CN CN
11 Arm to Level 1* X Y Y CY CY CY CY CY CY CN CN
12 Arm to Level 2 X Y Y CY CY CY CY CY CY CN CN
13 Arm to Level 3 X Y Y CY CY CY CY CY CY CN CN
14 Arm to Level 4 X Y Y CY CY CY CY CY CY CN CN
15 Arm to Level 5 N Y Y CY CY CY CY CY CY CN CN
18 Bypass Zones N Y Y CY CY CY CN CN CN CN CN
19 Bypass Critical Zones N Y Y CN CN CN CN CN CN CN CN
20 User Zone Test N Y Y CN CN CN CN CN CN CN CN
21 Phone Test Y Y Y CN CN CN CN CN CN CN CN
22 Program Schedules N Y Y CY CN CN CN CN CN CN CN
Program Mode Y*NNNNNNNNNN
Installer Zone Test Y$NNNNNNNNNN
Initiate Downloader Call YNNNNNNNNNN
Program Access Codes YYYNNNNNNNN
Reset Smoke Power YYYNNNNNNNN
Change Latchkey Time YYYNNNNNNNN
Initiate Fire Test YYYNNNNNNNN
Initiate LED Test YYNNNNNNNNN
Jump Areas NY&Y&NNNNNNNN
Control Lights YYYYYYYYYYY
Control Devices YYYYYYYYYYY
(I = Installer, P = Primary, F = Full)
Y = Yes.
N = No.
X = Within one hour of exiting pr ogr am mode.
CY = Configurable, defaulted to Yes.
CN = Configurable, defaulted to No.
* = All partitions/areas must be disarmed for installer to enter program mode.
$ = Partitions/area must be disarmed for installer t o enter installer zone test.
& = Must be a globa l c ode.
Table 4 list actions and whether they are allowed or disallowed for each of the eleven authorities.
Authority Level
Changing Authority Level Definitions
The amount you can and cannot do within each authority
level can be changed by redefining the definitions of each
level. By changing authorit y definition s, you co uld make a
lower authority level number capable to do less or you
could make a higher authority level number capable to do
more.
10
To change definitions for authority leve ls :
Steps Response
1. Press 1, 8. SECURITY MENU; ENTER YOUR CODE
2. Enter your primary
ACCESS CODE.
3. Press
9. ENTER AN AUTHORITY NUMBER THEN
4. Enter the authority
number and press
5. Press
00, # to list
ACCESS CODE MENU
PRESS #
ENTER ITEM TO CHANGE THEN PRESS
#.
#
authority definitions.
6. Enter the desired
authority definition to
change and press
AUTHORITY X; ENTER THE ITEM TO
CHANGE THEN PRESS #
#.
Advent® Home Navigator System
Page 13
Using the Phone with the System
Using the Phone with the System
Y ou can acces s the system using any touch-tone phone as a
remote control. Phone control is only available in part ition
1. This section explains how to:
q Access the system using a phone at home.
q Access the system while away from home.
q Adjust the phone volume.
When accessing the system using a phone, use the keypad
to enter commands just like an alphanumeric touchpad or a
hand-held touchpad.
1RWH
If you are using remote access (away from home) and
hang up while in a menu (instead of pressing *, * to quit),
the system will automatically hang up (on that end of the
line) after four minutes. If you h ang up while not in a
menu, it will automatic al ly hang up in 30 seconds.
Accessing the System Using a Home Phone
To operate the system using a home phone:
Steps Response
1. Pick up a Touch-Tone phone. Dial tone.
2. Press
3. Enter the desired commands just as
4. Press * twice to quit and hang up.
The system answers the phone and responds to numeric commands just as it would to a system touchpad.
#, * to access the system. SYSTEM HELLO, MAIN
MENU
you would a sy stem touchpad.
GOODBYE
1RWH
You can enter co m m ands without waiting for menu s to
be spoken.
ods: Ring-Hang-Ring and Ring -Count. Contact your security consultant if you want either method enabled or
disabled or to change the number of Ring-Count rings.
To access the system usin g R in g-Hang-Ring-Method:
Steps Response
1. Pick up an off-site Touch-Tone
Dial Tone
phone and dial your home phone
number.
2. Let the phone ring once and hang up.
3. Wait 10 to 30 seconds, dial again and wait for the system to answer.
SYSTEM HELLO. PLEASE
ENTER YOUR CODE
4. Enter your ACCESS CODE. MAIN MENU
5. Enter the desired commands just as you would a system touchpad.
6. Press * twice to quit and hang up.
To operate the system using Ring Count Meth od:
Steps Response
1. Pick up an off-site Touch-Tone
GOODBYE
Dial Tone
phone and dial your home phone
number.
2. Let the phone ring 12 (programmable) times and wait for the sys-
SYSTEM HELLO. PLEASE
ENTER YOUR CODE
tem to answer.
1RWH
The system will answer four rings
earlier if an alarm or trouble exists.
3. Enter your ACCESS CODE. MAIN MENU
4. Enter the desired commands just as you would a system touchpad.
5. Press * twice to quit and hang up.
GOODBYE
Accessing the System During a Phone Call
You can access the system when you are talking with
someone on the phone. The system puts the other person
on hold, allows system command entry as usual, and then
returns you to your call.
To interrupt a phone call:
Steps Response
1. Press #, * to put the person on hold
and to access the system.
SYSTEM HELLO,
MAIN MENU
2. Enter the desired commands just as you would a sy stem touchpad.
3. Press * twice to quit and return to your
GOODBYE
conversation.
1RWH
The other person on the line will not hear anything while
you access the syste m .
Accessing the System Away from Home
When you call the system, it needs to “know” when it
should answer the phone. It does this in one of two meth-
Advent® Home Navigator System
Bypassing an Answering Machine or Voice Mail
Y o u can access the system away from home if you have an
answering machine or voice mail by bypassing them. The
system requests an access code and then responds to system commands just as it would to a system touchpad.
To bypass an answering machine or voice mail:
Steps Response
1. Pick up an off-site Touch-Tone
Dial Tone
phone.
2. Dial your home phone number and wait for the answering machine or voice mail system to answer.
3. Press * twice, then
# twice. SYSTEM HELLO. PLEASE
ENTER YOUR CODE
4. Enter your ACCESS CODE. MAIN MENU
5. Enter the desired commands just as you would a system touchpad.
6. Press * twice to quit and hang up.
GOODBYE
11
Page 14
Alarms
1RWH
Disengaging Local Phone Control
When you want to use your phone to perform other phone
operations such as banking, you will need to disengage
phone control to your security system.
To disengage local phone control:
Steps Response
1. Pick up a Touch-Tone phone. Dial Tone
2. Press #, *.
SYSTEM HELLO.
3. Press 0. PHONE MENU
4. Press 0 to disable local phone. Dial Tone
5. Make phone call.
Local phone control stays di sabled until the phone is
placed back on the hook .
Adjusting the Phone Volume
When you want to adjust the phone volume to your comfort level for hearing.
To adjust the phone volume using a phone :
Steps Response
1. Pick up a Touch-Tone phone. Dial Tone
2. Press #, * to access the system.
3. Press 8. SYSTEM MENU
4. Press 5 for Phone Volu me. VOLUME LEVEL IS X; TO
5. Enter a new volume level and
press
# to accept.
6. Press * twice to quit and hang up.
To adjust the phone volume using an off-site phone:
Steps Response
1. Pick up a Touch-Tone phone. Dial Tone
2. Dial your home phone number.
3. Enter your ACCESS CODE. MAIN MENU
4. Press 8. SYSTEM MENU
5. Press 5 for Phone Volu me. VOLUME LEVEL IS X; TO
6. Enter a new volume level and
press
#.
7. Press * twice to quit and hang up.
SYSTEM HELLO, MAIN MENU
ACCEPT PRESS # OR
ENTER A NEW LEVEL FROM
1 TO 8 THEN PRESS #
VOLUME LEVEL IS NOW SET
TO X
GOODBYE
SYSTEM HELLO, PLEASE
ENTER YOUR CODE
ACCEPT PRESS # OR
ENTER A NEW LEVEL FROM
1 TO 8 THEN PRESS #
VOLUME LEVEL IS NOW SET
TO X
GOODBYE
Alarms
Emergency alarms notify you and the system monitoring
service in case of an emergency. Although alarms are automatically activated by the various system sensors, you can
also manually activate alarms.
When an alarm is activated, combinations of loud exterior
and interior sirens sound and a very realistic voice calls
out one of several messages, for example, Fire Alarm or
Police Alarm.
Your system has some precautionary features that allow
alarms to be validated or canceled before calling the central station. For example, when an intruder is detected,
your system sounds an alarm immediately in an attempt to
scare off the intruder. If the alarm verification feature* is
on, your system will not initiate a call to the central monitoring station unless a second sensor is activated within 4
minutes. You can also choose to delay the sounding of
exterior sirens for 15 seconds, giving you time t o correct
an arming mistake or a false alarm before your neighbors
are alerted.
* - Not available in UL listed installations.
Manually Activating Alarms
Manually activate an alarm in the case of an emergency or to test the system.
1RWH
If you are testing the syste m , be sur e t o not i f y th e m onitoring service and instruct them not to dispatch personnel.
To manually activate an alarm:
Alarm
Type
Steps
Press and
Police
hold both
police
buttons.
Press and
Fire
hold both
fire
buttons.
Auxiliary
or
Medical
Press and
hold both
auxiliary
buttons.
Police (burglary) alarms activate in door and outdoor siren s
and a police report will be sent to the monitoring service.
Fire alarms activate indoor and outdoor sirens (an d strobes
if any) and a fire report will be sent to the monitoring service.
Auxiliary or medical alarms activate indoor sirens and an
auxiliary report will be sent to the monitoring service.
You will hear this ON-OFF
(progammable) pattern…
indoor sirens outdoor sirens
steady on steady on
___ ___ ___ ___ ___ ___
_________
(silent)
12
Advent® Home Navigator System
Page 15
Manually Resetting Hardwired Smoke Detectors
Panic alarms can also be programmed to be triggered
using keychain touchpads, wireless touchpads, and pendant panic buttons.
Preventing Accidental Alarms
This section explains how to avoid the surprise and annoyance of accidental alarms.
Tips for Avoiding Accidental Alarms
q Be aware of the system devices and how they operate.
q Always make sure the door is fu lly clo sed when en ter-
ing and exiting the building.
q Remember to disarm the system if yo u are interrup ted
during the entry/exit delay time.
q Make sure all doors leading outside have delay times.
If your system is armed to HOME, an alarm will
sound immediately if you open a door that is set to
instant.
q Motion detectors operate by detecting the change in
temperature when something passes in front of them.
If you have pets, you may want to eliminate motion
detectors or ask your dealer to install “pet lenses.”
q Check the location of your smoke detectors. Keep in
mind that smoke detectors near bathrooms can be activated by steam from a shower, and smoke detectors
near your kitchen can be activated by smoke from
cooking.
Cancelling an Alarm
Cancelling an alarm turns off the siren s and in some cases,
also prevents the system from reporting to the monitoring
service.
q Police alarm—You must cancel the alarm within 5
(programmable) seconds to prevent the system from
reporting to the monitoring service.
q Fire alarm—Even if you cancel the alarm right away,
the system still reports to the monitoring service.
When this happens, call your monitoring service and
follow their instructions to prevent the fire department
from being dispatched.
q Auxiliary or medical alarm—You must cancel the
alarm within 5 (programmable) seconds to prevent the
system from reporting to the monitoring service.
To cancel an accidental alar m :
Alarm
Type
Police
Alarm
Fire Alarm Enter your
Auxiliary
or Medical
Alarm
Enter your ACCESS CODE
within 5 (programmable)
seconds of the alarm start.
then follow the instructions
from your monitoring
service to prevent the
police or fire department
from being di spatched.
Enter your
within 5 (programmable)
seconds of the alarm start.
Steps Response
ALARM CANCELED
Report canceled.
ACCESS CODE.
ACCESS CODE
ALARM CANCELED.
Report continues.
ALARM CANCELED
Report canceled.
Manually Resetting Hardwired
Smoke Detectors
Manually resetting a smoke detector following a test or
alarm resets tripped detectors. This procedure is rarely
needed because smoke detectors are automatically reset
when an alarm is acknowledged or canceled.
To manually reset tripped smok e det ec to rs :
Steps Response
1. Press 8, 9 (from main
menu).
2. Enter your ACCESS CODE. SMOKE LOOP RESET
1RWH
Do not reset smoke detectors until the location of the
activated detector is determined and the smoke source
removed.
SYSTEM MENU; RESET SMOKE
POWER; ENTER YOUR CODE
System Tampering
The system will automatically detect and indicate the type of tampering:
q Touchpad access code tampering - If set up by the
installer, four incorrect access code attempts results in
a KEYSTROKE VIOLATION/police alarm.
q Remote phone access code tampering - Four incorrect
attempts at entering an access code results in a TROUBLE
indication and temporarily disables further access.
q Phone line tampering - A TROUBLE indication results if
the phone line is cut.
q Equipment/sensor tampering - Results in a TAMPER
TROUBLE indication and/or an alarm.
Touchpad Access Code Tampering
The system can be programmed to detect four or more
incorrect access code entry attempts during any single session as unauthorized touchpad tampering. If this feature is
enabled, the system will respond with a a
TION trouble indication and a police alarm.
If you know that this was done in error, contact the monitoring service and let them know.
To cancel this alarm,
Steps Response
Enter your primary
ACCESS CODE.
ALARM/REPORT CANCELED, SECURITY IS
OFF
If canceled soon enough - within 5 seconds (programmable) - the alarm will be canceled and the report to the monitoring station stopped. If not canceled soon enough, the
monitoring service will dispatch the police. Police sirens
will sound until the alarm is canceled.
1RWH
To be on the safe side, call the m on itor i ng service even
if you think you may ha ve canceled the false alarm in
time to stop the report.
KEYSTROKE VIOLA-
Advent® Home Navigator System
13
Page 16
Security Protection
1RWH
Remote Phone Acce ss Code Tampering
Four incorrect attempts at entering an access code during
any single operation sessi on results in a
TROUBLE indication.
The system hangs up and will not allow further attempts
for 24 hours or until the system has been disarmed via an
on-site touchpad.
Hang up and wait for 24 hours and try again or follow these steps at the premises:
Steps Response
1. Press * to clear trouble indica-
Trouble beeps stop.
tion.
2. Press 1, 1, ACCESS CODE. SECURITY MENU;
SECURITY IS OFF
Trouble is acknowledged and fur t her r emote p hon e acces s is allowed.
Phone Line Tampering
If the phone line is cut, the system responds with a TROUBLE indication.
To stop the trouble beeps:
Steps Response
Press * to clear trouble indication. Trouble beeps stop.
Security Protection
Turning Security Protection On
Turning security protection on means arming the system
against fire, intrusion, or other emergencies. You can arm
the system to one of several levels depending on your
needs throughout the day. Table 5 shows which s ensors are
active in the various arming levels.
Table 5: Arming Levels
Sensors:
Indoor sensors
(motion, etc.).
Outdoor sensors
(door/window)
Environmental
sensors (smoke,
heat, carbon
monoxide, etc.).
* Arming to Night is like arming to Away, except a few desig-
nated indoor sensors remain disarmed (hallway outside your
bedroom). This would allow you to walk from your bedroom to the kitchen or ba throo m at nigh t withou t need ing to
disarm the entire system.
Active Arming Levels:
Off Home Night Away Silent
44 4
4444
44 4 4 4
If the phone line is still faulty, the trouble beeps will start
again within 24 hours (at the daily trouble indication
time). The display continues displaying a flashing * until
the trouble is fixed.
Have the phone line repaired immediately and notify the
monitoring service of the si t uation.
Equipment/Sensor Tampering
Tampering with system equipment, sensors, etc. (for
example, opening enclosures), results in a
indication and/or an alarm.
Replace any open system enclosures or sensor covers and clear the tamper indication.
To clear a tamper/alarm indication:
Steps Response
To clear a trouble indication,
press *.
or
To clear an alarm, enter your
ACCESS CODE.
SECURITY MENU; SECURITY IS
OFF
If any covers are still open, the trouble beeps will start
again in 24 hours. The display continues displaying a
flashing
* until the trouble is fixed.
TAMPER TROUBLE
Arming to Home
Arming to Home is used when you stay indoors but will be awake and active.
To arm the system to hom e:
Steps Response
1. Press 1, 2 (from main
menu).
2. Enter your
ACCESS CODE if
prompted.
SECURITY MENU; ARMING LEVEL
CHANGE; ENTER YOUR CODE;
TO QUIT PRESS *
PARTITION/AREA X ARMED - HOME; OK TO EXIT
3. Press * twice to exit.
Active sensors:
q Outdoor (perimeter door and window) sensors that are
not bypassed.
q Environmental sensors (smoke, heat, carbon monox-
ide).
Inactive sensors:
q Indoor (motion) sensors.
Arming to Away
Arming to Away is used when you leave and no one is supposed to be in or on the premises.
14
Advent® Home Navigator System
Page 17
Security Protection
To arm the system to away:
Steps Response
1. Press 1, 3 (from main
menu).
2. Enter your
ACCESS CODE if
prompted.
SECURITY MENU; ARMING LEVEL
CHANGE; ENTER YOUR CODE; TO
QUIT PRESS *
PARTITION/AREA X ARMED -
AWAY; OK TO EXIT
3. Press * twice to exit.
All (except bypassed) sensors will be active following an initial exit delay.
1RWH
Protected windows and doors must be either close d or
bypassed in order for the system to arm.
Arming to Night
Arming to Night is used when you will be staying inside— sleeping or inactive.
1RWH
Arming to Night is like arming to Away, except a few
designated indoor sensors remain disarmed (example:
hallway, kitchen, bathroom). This would allow you to
walk from your bedroo m to the kitc hen or bathroom at
night without needing to disarm the entire system.
To arm the system to night,
Steps Response
1. Press 1, 4 (from main
menu).
2. Enter your
ACCESS CODE if
prompted.
SECURITY MENU; ARMING LEVEL
CHANGE; ENTER YOUR CODE; TO
QUIT PRESS *
PARTITION/AREA X ARMED - NIGHT;
OK TO EXIT
3. Press * twice to exit.
All sensors will be active except those that are bypassed
and those designated indoor sensors preset by your security consultant.
1RWH
Protected windows and doors must be either close d or
bypassed in order for the system to arm.
Arming to Silent
Arming to Silent is the same as arming to away except police alarms are silent.
To arm the s y stem to sil en t:
Steps Response
1. Press 1, 5 (from main
menu).
2. Enter your
ACCESS CODE if
prompted.
SECURITY MENU; ARMING LEVEL
CHANGE; ENTER YOUR CODE; TO
QUIT PRESS *
PARTITION/AREA X ARMED -
SILENT; OK TO EXIT
3. Press * twice to exit.
All (except bypassed) sensors will be active following an initial exit delay.
1RWH
Protecte d w indows and door s must be either cl osed or
bypassed in order for the system to arm.
Bypassing
A security system cannot p rot ect an open door or window.
When you attempt to turn security protection
ON, the sys-
tem will warn you if a door or window has been left open.
However, you may want to arm the system anyway. To do
this, you must bypass the open door or window. You can
do this automatically for just this time or manually for
more than just this time.
Automatically Bypassing
When you cannot turn security protection on because the
system warns you about an open door/window or faulty
door/window sensor.
To bypass a door or window for this arming session only:
Steps Respon se
1. Press 1, (desired arming level 1-5), ACCESS CODE.
2. Press
1 to accept open
SECURITY MENU; ZONE ### IS
OPEN; PRESS 1 TO ACCEPT
ZONE ### BYPASSED
sensor.
The sensor stays ign ored (b yp ass e d) only until you disarm the system.
1RWH
See Manually Bypassin g an O p en Window or Door for
bypassing windows or doors for more than just this one
time.
Manually Bypassing
If the system consistently warns you about the same open
door/window or a faulty door/window sensor, you may
want to indefinitely bypass that zone until it can be fixed.
To bypass a door or window indefinitely:
Steps Response (if any)
1. Press 1, 7 ( from main menu). SECURITY MENU; ENTER YOUR
CODE
2. Enter your ACCESS CODE. ENTER THE ZONE NUMBER
THEN PRESS #; TO LIST
BYPASSED ZONES PRESS 0#
3. Enter the desired sensor
ZONE X BYPASSED
number to be bypassed and
press
# (ENTER).
The sensor stays bypassed until you unbypass the sensor using the same method.
Group Bypassing
This allows you to manually bypass a group of zones. A
bypass group and all zones in that group automatically
belong to the same partition or area.
Ask your installer about setting up a bypass group.
Advent® Home Navigator System
15
Page 18
Security Protection
1RWH
1RWH
To group bypass a group of sensors inde finitely:
Steps Response (if any)
1. Press 1, 7 (from main menu). SECURITY MENU; ENTER YOUR
CODE
2. Enter your ACCESS CODE. ENTER THE ZONE NUMBER
THEN PRESS #
3. Press
To group unbypass a group of sens or s in def initely:
90, the desired group
number to be bypassed and
# (ENTER).
then
Steps Response (if any)
GROUP X BYPASS COMPLETE;
MAIN MENU
1. Press 1, 7 (from main menu). SECURITY MENU; ENTER YOUR
CODE
2. Enter your ACCESS CODE. ENTER THE ZONE NUMBER
THEN PRESS #
3. Press
91, the desired group
number to be unbypa ssed and
then
# (ENTER).
GROUP X UNBYPASS
COMPLETE; MAIN MENU
No Delay
Arming modifiers such as
NO DELAY and LATCHKEY can be
added once the system arming level is entered.
When you want to arm the system with no entry delay.
To arm with no entry delay:
Steps Response (if any)
Press 1, (desired arming level
1-5), enter
prompted, and then
ACCESS CODE if
9.
SECURITY MENU; NO DELAY
The system will arm as usual but without the normal entry delay.
Do not use this no delay feature if you have to open a
protected door in order to enter.
Silent Arming
The Silent Arming menu is used to arm or disarm your
system without disturbing anyone with status beeps or
voice messages. This works the same as the security menu
for arming or disarming the system with one exception:
press
2 (silent arm menu) instead of 1 (security menu) to
access the silent arming menu. For example:
To silent arm the system to away:
Steps Response
1. Press 2, 3 (from main
menu).
2. Enter your
ACCESS CODE if
prompted.
SILENT ARMING MENU; ARMING
LEVEL CHANGE; ENTER YOUR
CODE; TO QUIT PRESS *
PARTITION/AREA X ARMED -
AWAY; OK TO EXIT
3. Press * twice to exit.
Protest beeps will still sound.
To turn on the st atus beeps and voice m ess ages again , arm
or disarm the system using the security menu as usual.
Turning Security Protection Off
Arming to OFF is used when security is not a concern. This
would be when you are home and will be going both
inside and out.
To turn system arm in g of f:
Steps Response
1. Press 1, 1 (from main
menu).
2. Enter your
ACCESS CODE if
prompted.
SECURITY MENU; ARMING LEVEL
CHANGE; ENTER YOUR CODE;
TO QUIT PRESS *
PARTITION/AREA X SECURITY IS
OFF
3. Press * twice to exit.
Sensors that will remain active:
q Environmental sensors (smoke, heat, carbon monox-
ide).
Sensors t hat will be inactive:
q Indoor sensors.
q Perimeter sensors such as doors and windows.
Using the No Activity Feature
The system can monitor the activity in your home and
automatically call for help if normal activities are not
detected within a defined period of time.
For example, if someone falls and can’t move, the system
will detect that normal activities, such as placing outgoing
calls or opening doors and window s, have not occu rred for
a predetermined No Activity time.
The system sounds a low-volume auxiliary alarm to let
you know there may be a problem. If all is well, you can
stop the siren by disarming your system. If the system is
not disarmed within 5 minutes, it calls the central monitoring station. The central monitoring station will send emergency personnel to the premises to check out the situation.
1RWH
Contact your security co nsultant to enable or disable
this feature.
Using Opening and Closing Reports
Opening and Closing Rep orts allow s pagerholder s, syst em
printer (if any), and the central station to be notified whenever the system is armed and/or disarmed.
Opening and closing reports occur without special user
input and without regard to any time schedule.
Whenever the system is disarmed, an op ening repor t is
paged, printed, or reported to the monitoring service. For
example,
CODE], [PARTITION/AREA NUMBER].
Whenever the system is armed, a closing report is paged,
printed, or reported. For example,
DEVICE TEXT OR ID], [USER CODE], [PARTITION/AREA NUMBER].
NORMAL OPENING, [SOURCE DEVICE TEXT OR ID], [USER
NORMAL CLOSING, [SOURCE
16
Advent® Home Navigator System
Page 19
Controlling Lights and Devices
1RWH
Contact your security consultant if you would like to turn
opening and closing re ports on or off for any programmed pager, system printer, or for the monitoring
service reporting.
If so programmed, opening and closing reports (as well as
all other system events) are automatically recorded in the
system history buffer. See Checking the History Buffer
section for details.
The system can also be set up to report if an opening or closing occurs outside a set schedule.
Open/Close Schedules
To define an open/close window in a partition for a given
day, exactly two open/close schedules must be valid on
that day. When neither schedule is on, the partition/area is
expected to be closed. After one schedule turns on the partition is expecting an opening. When both schedules are
on, the partition/area is expected to be open. When the
other schedule is off, the partition/area is expecting a closing. As soon as both schedules are off again, the partition/
area is expected to be closed again.
Opening/Closing Exception Reports
The opening and closing exception reports feature allows
programmed pagerholders and/or the central station to be
notified when arming or disarming occurs outside of specified time schedules.
When the system detects an opening or closing arming
change that is early, normal, or late, it reports the arming
change as such. If the system cannot classify an abnormal
arming change as early or late, it reports a generic exception. If at the end of an opening or closing time window,
the partition/area is not open or closed, respectively, the
system reports that the partition/area failed to open or
close.
Here are two specific examples of how opening and closing exception might be used in a business setting:
q Every morning you’d like to be notified if your busi-
ness is disarmed after its normal opening time.
q Every evening you’d like to be notified if your busi-
ness is armed before its normal closing time.
The most typical setup of this feature makes use of both
exception opening and exception closing. (However, it is
possible to use only exception opening or only exception
closing.)
Follow the detailed procedure defining opening and closing schedules located in the Setting W eek ly Schedules section.
1RWH
Contact your security consultant if you would like to turn
the exception reporting on or off for any particular pager,
system printer, or for the centr al station .
Controlling Lights and Devices
Lights
Lights controlled by the system can be turned on and off
manually or automatically. See Automating the System
Using Schedules for details on controlling lights auto matically.
1RWH
Contact your security consultant for adding or removing
controlled lights.
Manually Turning All Lights On or Off at Once
To turn all controlled lights on or off:
Steps Response
1. Press G (on bulb) twice rapidly. ON
2. Press H (off bulb) twice rapidly. OFF
or
Steps Response
1. Press 4, 0#. ENTER A LIGHT NUMBER THEN
2. Press
1 (for on) or 2 (for off). LIGHTS ARE NOW ON/OFF
1RWH
Turning off all lights turns off all devices as well.
Manually Turning One Light On or Off
When turning selected lights on or off, you will also be able to brighten or dim them.
To turn selected controlled lig hts on or off:
Steps Response
1. Press 4. ENTER A LIGHT NUMBER THEN
2. Enter the desired light number then press #.
3. Press
4. Press
1 (for on) or 2 (for off).
* twice to exit. MAIN MENU; GOODBYE
Brighten or Dim Lights
To brighten or dim selected controlled lights:
Steps Response
1. Press 4. ENTER A LIGHT NUMBER THEN
2. Enter the desired light number then press
#.
3. Press either 4 or 5 repeatedly to brighten or dim light.
4. Press * twice to exit.
PRESS #; ALL LIGHTS MENU;
TO TURN ON NOW PRESS 1;
TO TURN OFF NOW PRESS 2
PRESS #
X IS ON/OFF; LIGHT MENU; TO
TURN ON NOW PRESS 1; TO
TURN OF NOW PRESS 2
PRESS #
X IS ON/OFF; LIGHT MENU
MAIN MENU; GOODBYE
Advent® Home Navigator System
17
Page 20
Chime and Latchkey Features
1RWH
1RWH
Devices (Appliances)
Just like lights, devices (appliances) controlled by the system can also be turned on and off manually or automatically according to a preset schedule. See Automating the
System Using Schedules for det ails on control ling devi ces
automatically.
Manually Turning a Single Device On and Off
To turn selected controlled devices on or off:
Steps Response
1. Press 5 (desired device number), #.
2. Press
1 for on or 2 for off. ON/OFF
Contact your security consultant for adding or removing
controlled devices.
DEVICE MENU, [DEVICE NAME].
Chime and Latchkey Features
Chime Feature
The chime feature will alert you whenever someone enters
or leaves through a perimeter door. This may be used, for
example, during a party to announce arriving guests or
during the day to announce exits and entries.
Arm the system to AWAY adding t he LATCHKEY arming modifier:
Steps Response
Press 1, 3, ACCESS CODE (if
requested), 8.
SECURITY MENU; AWAY,
LATCHKEY
Automating The System Using Schedules
Schedules are used to automatically control the sys tem at a
predetermined day and time. Schedules can be used for
automatically turning system controlled lights and devices
on or off. They can automatically arm or disarm the system and also define time periods during which business
type openings, closings, and access codes are valid.
Each system partition/area (separate protected area) can
have up to 32 programmed (numbered) schedules. All
schedules belong to a partition/area; there are no global
schedules.
Each schedule also has an arming type defining what arming actions, if any, are taken at a schedule transition. The
daylight type determines whether the schedule is used in
type defining whether on or off-times are adjusted daily
based on variations in sunrise or su nset . The dayl igh t type
also determines whether the panel is the in the Northern or
Southern hemisphere.
To turn the chime feature on o r off:
Steps Response
Press 7, 1 (from
main menu).
To change which doors (or other sel ec te d sensors)
chime or what text message is indicated (if any), contact
your security consultant.
FEATURES MENU, CHIME ON (if off) or
CHIME OFF (if on).
Latchkey Feature
The latchkey feature pages you if someone, such as a
child, doesn’t arrive home and disarm the sys tem by a d e signated time. If programmed to do so, the system will also
phone in a report to the monitoring service. The latchkey
time need only be set to the desired time once.
To set th e latchkey ti me:
Steps Response
1. Press 7, 2 (from main menu). FEATURES MENU; PRESENT
2. Press # to accept the indicated time or enter the new
[desired time] (for example,
440 for 4:40), #.
3. Press 1 for A.M. or 2 for P.M. A.M. or P.M.
LATCHKEY TIME
NEW LATCHKEY TIME
Schedule Types
Every schedule is defined to be either valid or invalid during four different schedule types in a given partition/area.
The types are:
q Type 1 (Normal) is valid whenever it is not a holiday
and the schedule condition is not temporary.
q Type 2 (Holiday A) is valid when the current date
matches a holiday date programmed in the Holiday A
list. This list is pre-programmed by the installer. A
holiday condition is overridden by a temp orary condition.
q Type 4 (Holiday B) is valid when the current date
matches a holiday date programmed in the Holiday B
list. This list is also pre-programmed by the installer.
A holiday condition is overridden by a temporary
condition.
q Type 8 (Temporary) is valid during a temporary con-
dition which has been turned on by the user via the
Schedule Menu. It will stay there until the temporary
condition is canceled by the user. The temporary condition overrides all other conditions.
Any schedule can be defined to be valid in any combination of these conditions. When the schedule is defined in
the Schedule Menu, the user is prompted for the schedule
type. To determine the type, give each condition the
numerical value in parentheses above and add up the values. For example, if a schedule should be valid under normal and holiday B conditions, the schedule type is 5 (see
Table 6).
18
Appendix D has a table to list and keep track of all your
programmed schedule conditions and options. Refer to
Advent® Home Navigator System
Page 21
Automating The System Using Schedules
Tables 12 and 13 in Appendix D to list all your programmed Holidays.
1RWH
Only your installer can pr ogr am t he holiday list
Table 6: Schedule Types
Schedule
Type
Conditions
1Normal
2 Holiday A
3 Normal + Holiday A
4 Holiday B
5 Normal + Holiday B
6 Holiday A + Holiday B
7 Normal + Holiday A + Holiday B
8Temporary
9 Normal + Temporary
10 Holiday A + Temporary
11 Normal + Holiday A + Temporary
12 Holiday B + Temporary
13 Normal + Holiday B + Temporary
14 Holiday A + Holiday B + Temporary
15 Norm al + Holiday A + Holiday B + Temporary
Arming Schedules
Besides a schedule type, every schedule also has an arming type. Table 7 defines the valid arming types. To keep
scheduled arming simple, only one arming schedule
should be defined on a given day.
Table 7: Arming Types
Arming
Type
Arming Action
for On-
Transition
0None None No
1Disarm Arm No
2Arm Disarm No
3 Arm None No
4Disarm None No
5None Arm No
6None Disarm No
7None None No
8None None Yes
9Disarm Arm Yes
10 Arm Disarm Yes
11 Arm None Y es
12 Disarm None Yes
Arming Action
for Off-
Transition
Opening/
Closing
Schedule
Table 7: Arming Types (Continued)
Arming
Type
Arming Action
for On-
Transition
Arming Ac tion
for Off-
Transition
Opening/
Closing
Schedule
13 None Arm Yes
14 None Disarm Yes
15 None None Yes
Sunrise/Sunset Schedules
Schedule on- or off-times may be tied to the daily variations in sunrise and sunset. Each midnight, sunrise/sunset
schedules are adjusted based on the change in sunrise or
sunset times. The amplitude of the variations is based on
the programmed latitude. When programmed, each schedule is assigned a daylight type. Table 8 defines the daylight
types.
Table 8: Daylight Types
Daylight
Type
Sunrise/Sunset
Adjustment for
On-Transition
Sunrise/Sunset
Adjustment for
Off-Transition
Hemisphere
0 None None North
1 None None South
2 Sunset Sunrise North
3 Sunset Sunrise South
4 Sunrise Sunset North
5 Sunrise Sunset South
6 Sunset None North
7 Sunset None South
8 Sunrise None North
9 Sunrise None South
10 None Sunset North
11 None Sunset South
12 None Sunrise North
13 None Sunrise South
14 Sunset Sunset North
15 Sunset Sunset South
16 Sunrise Sunrise North
17 Sunrise Sunrise South
For example, if a schedule on-time should vary with the
daily sunset time bu t the s chedule d of f-t ime shou ld be constant, then the schedule daylight type is 6. Or, if the onand off-times should both track with the sunset and the
panel is in the Southern Hemisphere, the daylight type is
15.
Weekly Schedules
There are two similar, bu t different s chedule types: weekly and one-time.
q Weekly schedules are repeatedly used on certain times
Advent® Home Navigator System
19
Page 22
Automating The System Using Schedules
and days of the week. These schedules remain active.
q One-Time schedules are those that are used only once
at a set on- and off-time and then automatically made
inactive by the system.
Any schedule can be defined to be a weekly schedu le. Fo r
a weekly schedule, the user defines on what days of the
week the schedule is valid. A weekly schedule must have a
valid on-time and a valid off-time. These times define
Steps Response
when the schedule should turn on and off and are the s ame
for every day of the week. If the off-time is earlier than the
on-time, then the off-time is assumed to be for the next
day.
Any automatic actions (lights, devices, access codes) set to
use this weekly schedule will repeatedly activate on the
days and times set.
To set a weekly schedule:
1. Press 7, 4 (from main menu). FEATURES MENU; ENTER YOUR CODE
2. Enter your primary ACCESS CODE. SCHEDULES ARE NORMAL; ENTER A SCHEDULE NUMBER THEN PRESS # OR TO LIST
SCHEDULES PRESS 0 # OR TO ENABLE TEMPORARY SCHEDULES PRESS 00 #
3. Enter the desired schedule number and
#.
press
Enter desired num be r (s), and then #.
1 - Monday
2 - Tuesday
3 - Wednesday
4 - Thursday
5 - Friday
SCHEDULE VALID ON NO DAYS; TO ACCEPT PRESS # TO ADD XXX (days) PRESS X (the days
number);
PRESS *
SCHEDULE IS WEEKLY; NO ON TIME; TO ACCEPT PRESS # OR ENTER A NEW ON TIME THEN
PRESS #; FOR NO ON TIME PRESS 0 #; TO CHANGE THE DAYS OF THE WEEK PRESS *
TO CHANGE TO A ONE TIME SCHEDULE PRESS 0; FOR A DIFFERENT SCHEDULE
1RWH
The system will automatically make it a weekly schedule if you don’t select the
one-time schedule (0) option.
6 - Saturday
7 - Sunday
8 - Add all days
9 - Remove all days
0 - One time schedule
4. Enter the time you want your schedule to
FOR AM PRESS 1 FOR PM PRESS 2 TO CHANGE THE ON TIME PRESS *
start and press #.
5. Press
6. Enter the time you want your schedule to
7. Press
8. Enter the desired schedule type number
9. Enter the desired arming schedule option
10. Enter the desired schedule dayli ght option
1 or 2. ON TIME IS NOW XX:XX AM/PM; NO OFF TIME TO ACCEPT PRESS # OR ENTER A NEW OFF TIME
end and press
1 or 2. OFF TIME IS NOW XX:XX AM/PM;
then press
number (0-15) then press
number (0-17) then press
#.
# (see Table 6).
# (see Table 7).
# (see Table 8).
THEN PRESS # FOR NO OFF TIME PRESS 0 #
FOR AM PRESS 1 FOR PM PRESS 2 TO CHANGE THE OFF TIME PRESS *
SCHEDULE TYPE IS 0 TO ACCEPT PRESS # OR ENTER A NEW SCHEDULE TYPE THEN PRESS #
SCHEDULE IS NOW TYPE X TO ACCEPT PRESS # TO ENTER A NEW SCHEDULE TYPE PRESS *;
SCHEDULE ARMING OPTION IS 0 TO ACCEPT PRESS # TO ENTER A NEW SCHEDULE ARMING
OPTION THEN PRESS #
SCHEDULE ARMING OPTION IS NOW X TO ENTER A NEW SCHEDULE ARMING OPTION PRESS *
SCHEDULE DAYLIGHT OPTION IS X TO ACCEPT PRESS # TO ENTER A NEW SCHEDULE
DAYLIGHT OPTION PRESS *
SCHEDULE DAYLIGHT OPTION IS NOW X TO CHANGE SCHEDULE DAYLIGHT OPTION PRESS *
Your schedule is then displayed in its entirety.
11. Press * twice to exit.
One-Time Schedules
One-time schedules work the same way as weekly schedules, except that they are only valid once and not on cer-
20
tain days of the week. The schedule type is set to 0 when
the schedule turns off. One-time schedules are automatically made inactive at the scheduled off-time setting.
Advent® Home Navigator System
Page 23
Automating The System Using Schedules
To set a one-time schedule:
Steps Response
1. Press 7, 4 (from main menu). FEATURES MENU; ENTER YOUR CODE
2. Enter your primary ACCESS CODE. SCHEDULES ARE NORMAL; ENTER A SCHEDULE NUMBER THEN PRESS # OR TO LIST
SCHEDULES PRESS 0 # OR TO ENABLE TEMPORARY SCHEDULES PRESS 00 #
3. Enter the desired schedule number and
press
#.
4. Press 0, (to make it a one-time schedule), and then #.
SCHEDULE VALID ON NO DAYS; TO ACCEPT PRESS # TO ADD XXX (days) PRESS X (the days
number); TO CHANGE TO A ONE TIME SCHEDULE PRESS 0; FOR A DIFFERENT SCHEDULE
PRESS *
SCHEDULE IS ONE TIME; NO ON TIME; TO ACCEPT PRESS # OR ENTER A NEW ON TIME THEN
PRESS #; FOR NO ON TIME PRESS 0 #; TO CHANGE THE DAYS OF THE WEEK PRESS *
1 - Monday
2 - Tuesday
3 - Wednesday
4 - Thursday
5 - Friday
6 - Saturday
7 - Sunday
8 - Add all days
9 - Remove all days
0 - One time schedule
5. Enter the time you want your schedule to
start and press
6. Press
1 or 2. ON TIME IS NOW XX:XX AM/PM; NO OFF TIME TO ACCEPT PRESS # OR ENTER A NEW OFF TIME
#.
7. Enter the time you want your schedule to
end and press
8. Press
1 or 2. OFF TIME IS NOW XX:XX AM/PM; SCHEDULE TYPE IS 0 TO ACCEPT PRESS # OR ENTER A NEW
#.
9. Enter the desired schedule type number
then press
# (see Table 6).
10. Enter the desired arm i ng sc hed ul e type
number then press
# (see Table 7).
11. Enter the desired schedule daylight option
number then press
12. Press
* twice to exit.
# (see Table 8).
FOR AM PRESS 1 FOR PM PRESS 2 TO CHANGE THE ON TIME PRESS *
THEN PRESS # FOR NO OFF TIME PRESS 0 #
FOR AM PRESS 1 FOR PM PRESS 2 TO CHANGE THE OFF TIME PRESS *
SCHEDULE TYPE THEN PRESS #
SCHEDULE IS NOW TYPE X TO ACCEPT PRESS # TO ENTER A NEW SCHEDULE TYPE PRESS *;
SCHEDULE ARMING OPTION IS 0 TO ACCEPT PRESS # TO ENTER A NEW SCHEDULE ARMING
OPTION THEN PRESS #
SCHEDULE ARMING OPTION IS NOW X TO CHANGE SCHEDULE ARMING OPTION PRESS *
SCHEDULE DAYLIGHT OPTION IS X TO ACCEPT PRESS # TO ENTER A NEW SCHEDULE
DAYLIGHT OPTION PRESS *
SCHEDULE DAYLIGHT OPTION IS NOW X TO CHANGE SCHEDULE DAYLIGHT OPTION PRESS *
Your schedule is then displayed in its entirety.
Associating Lights, Devices and Access Codes with Schedules
The association of schedules with lights, devices, and
access codes are programmed in the Light Menu, Device
Menu, and Access Code Menu, respectively.
Lights and Devices
Each valid menu output can be associated with any of the
schedules in its partition/area. Whenever a transition of an
associated schedule occurs, the state of the output is
reevaluated. All schedule transitions occur at minute
boundaries. The following rules apply:
q If any associated schedules turn on, the output is
turned on.
q If any associated one-time schedule turns off, the out-
put is turned off. This occurs even if other associated
Advent® Home Navigator System
schedules are still on.
q If any associated weekly schedule turns off and there
are no associated schedules on, the output is turned
off. If any other associated schedules remain on, the
output is unchanged.
Some general rules are that on-transitions have priority
over off-transitions, and one-time schedules have priority
over weekly schedules. Also, user-initiated changes (i.e.
an output state change via a touchpad) have priority over
scheduled changes, so that when an output is turned on or
off by a user its state does not change back until the next
valid schedule transition.
Controlling Lights Automatically
The system can be programmed to turn lights controlled
by the system on and off automatically according to a preset schedule.
21
Page 24
System Status
To set up a light schedule
Steps Response
1. Press 4, (desired light num-
#.
ber),
2. Press
3, (desired schedule
number(s)),
0, #.
LIGHTS MENU, [LIGHT NAME]
SCHEDULE NUMBER
Controlling Devices Automatically
Just as the system can be programmed to control lights
automatically, it can control devices (appliances) automatically as well.
To set a device schedul e:
Steps Response
1. Press 5, (desired device
number),
2. Press
number),
#.
3, (desired schedule
0, #.
DEVICE MENU, [DEVICE NAME].
SCHEDULE NUMBER.
Access Code Schedules
Each valid access code except those which can never be
disabled (installer and primary codes) can be associated
with any of the schedules in its partition. Global codes, i.e.
those valid in all partitions, can only be associated with
schedules in partition 1. When a transition of an associated
schedule occurs, nothing happens to the access code.
Rather, the validity of an access code is determined when
the code is being used. When a user is prompted for a
code, the system checks whether any schedules are tied to
the code. If so, the code is valid whenever any of its associated schedules is on and invalid if all of its associated
schedules are off.
To change an access code’s schedule:
Steps Response
1. Press 1, 8 (fro m main
menu).
SECURITY MENU; ENTER YOUR
CODE
2. Enter your ACCESS CODE. ACCESS CODE MENU
3. Press 5. ENTER THE CODE TO CHANGE
THEN PRESS #
4. Enter the
change and press
5. Enter the schedule number and press #.
6. Press
ACCESS CODE to
#.
0, #. CODE SET TO X
CODE SET TO X SCHEDULE;
ENTER A SCHEDULE THEN
PRESS #
SCHEDULE X ADDED; TO
ACCEPT PRESS 0 #
7. Press * twice to exit.
System Status
Your system has been designed to keep false alarms and
system problems to a minimum. If there is a p roblem, your
security system can diagnose it and then sound trouble
beeps to let you know about it. In most instances, your
system can alert your central monitoring station of the
problem as well.
Checking the System Status
When you want to know the current status of the system
including its arming state and any current problems.
To check the system st at us:
Steps Response
1. Press 1, 9. SYSTEM MENU; CHECK STATUS
2. Press UNDO (*) to quit. GOODBYE
22
What the Status or Trouble Beeps Mean
Your Advent system’s alphanumeric touchpads, interior
sirens and speakers use status and trouble beeps to communicate what the system is doing or if there is a problem.
You will hear some sounds each time you tell your system
to do something. Some will only sound when the system
protests in some way. Table 9 describes the operating and
trouble beeps you may hear from your system.
Advent® Home Navigator System
Page 25
Table 9: Status and Trouble Beeps
Type of Sound Sound Pat te rn What These Sounds Mean
When You Arm or
Disarm
When You Enter
or Exit
1 short beep
2 short beeps
3 short beeps
1 long, 1 short beep
1 long, 2 short beeps
3 short beeps every 2 secon d s
Your system disarmed to OFF.
Your system armed to HOME.
Your system armed to AWA Y.
Your system armed to NIGHT.
Your system armed to SILENT.
Your system is ar med and the exit delay is in progress. (Beeps sound once
per second during the last 10 seconds.)
Or
3 short beeps every second
Your system is armed and the entry delay is in progress.
Your system is armed, an alarm has occurred, the alarm sirens have already
“timed out,” and the entry delay is in progress.
Chime Feature On 2 short beeps (or “ding-dong”
sound)
Protest Beeps 1 long, 1 short beep
continuous sequence. Once
per second.
Your system is OFF. The chime feature is on, and an exterior sensor like a
door or wind ow is opened.
Your are trying to arm with one of the many possible protest conditions
present. You will be asked if you want to accept the protest condition after
you enter your code.
For example, you are trying to arm to HOME or AWAY with an exteri or
door or window open. Close the door or windo w or see section “Arming
with a Door or Window Open.”
or
You are trying to disarm after an alarm has occurred and the alarm sirens
have already “timed out.”
System Trouble
Beeps
6 short beeps once every 60
seconds (6 beeps may sound
for any of these reasons)
Some examples:
Your system has an AC power failure.
Your system has low sensor or touchpad battery.
Your control panel can’t communicate with a hardwire device, such as a
hardwire sensor.
Your system has sensor or touchpad failure.
Your system has a low battery.
Your system has failed to communicate with the central monitoring service.
Your system memory has failed.
There is a sire n wiring problem.
System Status
Table 10 describes the conditions under which some trouble beeps occur and when they begin.
Table 10: Trouble Beep Conditions
Condition When Beeps Begin
AC Power Failure 8 seconds (programmable) a fter failure is detected. (If programmed to do so, a report is sent to the
central monitoring station at this time or after 1-12 hours [programmable.*]) The system will continue to
operate under backup batter y power.
Fail-to-
After fifth (programmable) unsuccessful attempt to phone the monitoring service.*
Communicate
Hardwire Sensor
As soon as the system detects the condition.*
Trouble
Phone Fail Trouble As soon as the system detects the condition.*
* and also at preprogrammed daily trouble indication time if any.
Advent® Home Navigator System
23
Page 26
Maintaining Your System
Checking the Alarm History
When you want to know which and how many alarms
sounded in your absence. The system re ports the following
information about the last alarms:
q The alarm type.
q Which sensor activated the alarm.
q The date and time the alarm happened.
To check the alarm hist ory:
Steps Response (if any)
1. Press 1, 0 (from main menu). SECURITY MENU, CHECK
ALARM HISTORY
2. Press UNDO (*) to return to the
GOODBYE
main menu.
Viewing the History Buffer
Viewing the his tory buffer allows you to learn th e system’s
history of events. It gives a detailed report of every event,
including:
q Each sensor that was activated and at what time/date.
q Each time an access code was entered.
q Alarms/troubles etc.
q Any other system events programmed to be stored in
the history buffer.
To view the history buffe r:
Steps Response (if any)
1. Press 7, 5 (from main menu). SYSTEM MENU, VIEW HISTORY
BUFFER
2. Press # to skip to the next his-
tory event.
3. Press
UNDO (*) to quit. GOODBYE
HISTORY (if any) is
indicated.
Maintaining Your System
Testing
The system has both automatic and manual built-in test features.
Automatic Test Features
The system automatically tests and reports any problems with the following parts of the system:
q battery—The system automatically tests the backup
battery voltage and notifies you if it is low.
q phone—Depending on your s ys tem con fi gur atio n and
programming, it may automatically test the phone
connection to the monitoring service once a week.
q phone line—The system automatically tests line volt-
age.
Testing the System Manually
Yo u may also test the system manually when desire d.
Testing the Phone Connection to the Monitoring Service
Test the phone communications after any phone line/system repairs or change in your service, such as a second
line, a change in area code or prefix, or adding/removing
call or monitoring services.
After installing a new phone, modem, or other device on the same line.
To test phone operation,
Steps Response
1. Press 0, 1 (from main menu). PHONE MENU. PHONE TEST
2. Enter your primary ACCESS
CODE.
3. Wait for acknowledgment indication.
PHONE TEST ON
The system should report
PHONE TEST OK
Testing Sensors/Inputs (Zones)
Testing sensors allow s you to activate any sensor (system
input device) and verify its correct operation without causing an alarm. Do this after new sensors are installed or old
ones replaced.
1RWH
All security/fire protect ion is di sabled during a zone test.
To test sensors,
Steps Response
1. Press 8, 1 (fro m main menu). SYSTEM MENU, ZONE TEST
2. Enter your ACCESS CODE. ZONE TEST ON
3. Activate the desired sensor/ input device(s).
The system should report
ZONE # GOOD for the
device activated.
4. Press
5. Press
8, 2 to list zones tested.
8, 3 to list zones not
tested.
6. Press
1, 1 and enter your
ACCESS CODE (if prompted) to
[PARTITION NAME] SECURITY
IS OFF
manually end zone test.
If the system does not respond to an input device, see
“Troubleshooting” section. If not ended manually, zone
test will automatically time-out and end.
Testing the Panel Backup Battery
The panel backup battery can be tested manually, for
example, when replaced or following a lengthy power outage.
To test the panel backup battery :
Steps Response
1. Press 8, 8 (from main menu). SYSTEM MENU; BATTERY
TEST; BATTERY TEST XX.X
VOLTS
2. Press UNDO (*) to end the test. GOODBYE
24
Advent® Home Navigator System
Page 27
Troubleshooting
1RWH
Battery test voltage should range from 12 to 14 volts. If
not, or if BATTERY BAD is indicated, see “Troubleshooting”
section.
Your system has a backup battery that will secu r e your
home even during an AC power failure. An optional feature allows your system to alert the central monitoring station if the power is off. The system reports again when
power has been restore d.
Cleaning the System Components
You should clean your system at least once per year, or as
needed. Use a damp, warm rag and a mild, non-abrasive,
water-based cleaning solution to clean all touchpads,
enclosures, and housings.
Checking and Changing Batteries
System module and sensor batteries are automatically and
periodically tested by the system. If the system indicates a
module or sensor
LOW BATTERY message, contact your secu-
rity consultant. They will replace the module or sensor battery.
Troubleshooting
Table 11 contains a summary of some simple system problem solving techniques.
Table 11: Troubleshooting
Feature Problem Solution
Arming/
Disarming
System won’t arm. Make sure all monitored perimeter doors and windows are closed or
accept open zones (bypass them) and accept the trouble causing protest.
Someone else is controlling your system from a different touchpad or
phone.
Bypass Panel announces
you try to bypass a sensor.
INVALID when
You are trying to bypass a 24-hour (environmental) sensor that cannot be
bypassed, or your code does not have the authority to bypass critical
sensors.
Batteries Panel announces
FAILURE or SENSOR NN LOW BATTERY.
SYSTEM BATTERY
Call your security system consultant for battery replacement.
False Alarm Alarm report is being sent. Immediately enter your access code to cancel the alarm. This command
cancels the alarm and if done within 5 seconds (programmable) does not
call in a report to the central monitoring station.
Smoke Sensor Beeps once every minute. Batteries are low. Replace the smoke sensor batteries.
Trouble Beeps 6-beep sequence once every 60
seconds.
Press undo (*) to silence the trouble beeps. (Press once for each problem).
This disables the trouble beeps until the preprogrammed trouble
indication time.
Controlled Lights
or Devices
Lights or devices controlled by
the lamp or appliance modules
do not work.
Make sure the lamp has a working bulb.
Check the lamp or device operation at a working outlet.
Make sure the lamps or devices are switched ON and are plugged into the
lamp or appliance module. Make sure that the modules are plugged into
outlets not controlled by a switch.
Advent® Home Navigator System
25
Page 28
Appendix A: Planning for Emergencies
,PSRUWDQW
Appendix A: Planning for
Emergencies
Develop a plan to prepare for a fire or other emergency.
Rehearse your plan with everyone by doing a fire drill
every few months.
Guidelines
q Understand how to use your fire system.
q Know the normal state of doors and windows: open,
closed, or locked.
q Escape fast! (Do not stop to pack.)
q Use a different escape route if closed doors feel hot to
the touch.
q Crawl and hold your breath as much as possible to
help reduce smoke inhalation during your escape.
q Meet at a designated outdoor location.
q Emphasize that no one should return to the premises if
there is a fire.
q Notify fire department f rom another ph one outside the
building.
Emphasize that no one should enter the building if they
hear sirens.
Floor Plan Example
Use this example to draw your floor plan on the next pag e and plan your escape routes.
A smoke detector should
be located on each level.
Bedroom
Bedroom
Hall
Living
Room
Basement
Dining
Room
TV
Room
NOTE: Ceiling-mounted smoke detectors should be located in the center of the room
or hall, or not less than 4 inches from the wall. When the detector is mounted
on the wall, the top of the detector should be 4 to 12 inches from the ceiling.
NOTE: Do not install smoke detectors where normal ambient temperatures are above
100°F or below 40°F. Also, do not locate detectors in front of AC/ Heat
registers or other locations where normal air circulation will keep smoke
from entering the detector.
NOTE: Additional information on household fire warning is available at nominal
cost from: The National Fire Protection Association, Batterymarch Park,
Quincy, MA 02269. Request Standard No. NFPA74.
H
x
Dining
Room
Bedroom
Kitchen
H
Living
Room
Dining
Room
Living
Room
Bedroom
Required smoke detector
Heat detector
Indicates smoke detector is optional if door is not provided between
basement and recreation rooms.
Kitchen
H
Hall
Bedroom
Bedroom
Bedroom
Living
Room
Basement
Bedroom
In fa mi ly li vin g u ni ts wi th mor e
than one sleeping area, locate a
smoke detector at each area.
Bedroom
Bedroom
Hall
x
Recreation
Room
Smoke detectors should
be located between the
sleeping area and the rest
of the family living unit.
Your Floor Plan
Use the following guidelines when drawing your floor plan on the following page:
q Show all building levels.
q Show the exits from each room (two exits per room
are recommended).
q Show the location of all components of the fire sys-
tem.
q Show the locations of all fire extinguishers, hoses,
ladders, etc.
26
Advent® Home Navigator System
Page 29
Draw your floor plan in this space.
Appendix A: Planning for Emergencies
Advent® Home Navigator System
27
Page 30
Appendix B: System Menu Map
Appendix B: System Menu Map
M A I N M E N U
1 S E C U R I T Y
1 S e c u r i t y O f f
2 A r m t o H o m e
3 A r m t o A w a y
4 A r m t o N i g h t
5 A r m t o S i l e n t
6 M o d i f i e r L i s t
7 B y p a s s a Z o n e
8 A c c e s s C o d e s
9 S e c u r i t y S t a t u s
0 A l a r m H i s t o r y
* R e t u r n t o M a i n M e n u
6 E N E R G Y
( N o t U s e d )
P r e s s :
# t o s k i p t o n e x t i t e m
* t o r e t u r n t o M e n u
* * t o e x i t t o M a i n M e n u
2 S I L E N T A R M
1 S e c u r i t y O f f
2 A r m t o H o m e
3 A r m t o A w a y
4 A r m t o N i g h t
5 A r m t o S i l e n t
6 M o d i f i e r L i s t
* R e t u r n t o M a i n M e n u
7 F E A T U R E S
1 C h i m e
2 L a t c h k e y T i m e
3 L i g h t s & D e v i c e s
4 S c h e d u l e s
5 V i e w H i s t o r y B u f f e r
7 R e d i r e c t T o u c h p a d
* R e t u r n t o M a i n M e n u
3 A C C E S S C O N T R O L
( N o t U s e d )
8 S Y S T E M
1 Z o n e T e s t
2
3
4 F o r S t a t u s V o l u m e
5 F o r P h o n e V o l u m e
6
7 F i r e T e s t
8 B a t t e r y T e s t
9 R e s e t S m o k e P o w e r
0 F o r P r o g r a m M o d e
* R e t u r n t o M a i n M e n u
4 L I G H T S
M u s t b e f i r s t l e a r n e d
i n u s i n g t h e F e a t u r e s
M e n u .
1 T u r n [ s e l e c t e d l i g h t ]
O n N o w ( i f o f f )
2 T u r n [ s e l e c t e d l i g h t ]
O f f N o w ( i f o n )
3 S e t [ s e l e c t e d l i g h t ]
T o a S c h e d u l e
4 T o B r i g h t e n
5 T o D i m
* F o r a D i f f e r e n t L i g h t
* * R e t u r n t o M a i n M e n u
9 S C R I P T S
( N o t U s e d )
5 D E V I C E S
M u s t b e f i r s t l e a r n e d
i n u s i n g t h e F e a t u r e s
M e n u .
1 T u r n [ s e l e c t e d D e v i c e ]
O n N o w ( i f o f f )
2 T u r n [ s e l e c t e d D e v i c e ]
O f f N o w ( i f o n )
3 S e t [ s e l e c t e d D e v i c e ]
T o a S c h e d u l e
* F o r a D i f f e r e n t D e v i c e
* * R e t u r n t o M a i n M e n u
0 P H O N E
1 F o r P h o n e T e s t
2 F o r D o w n l o a d
0 T o D i s a b l e L o c a l
P h o n e C o n t r o l
( f r o m p h o n e o n l y )
* R e t u r n t o M a i n M e n u
28
8 5 4 3 g 1 4 7 b . d s f
Advent® Home Navigator System
Page 31
Appendix C: Display Error Messages and Meanings
Appendix C: Display Error Messages and Meanings
Message# INVALID Meaning Invalid keypad entry
* (blinking asterisk)
[Bus Module description] RECEIVER
FAILURE
[Bus Module description] ANTENNA
TAMPER
[Bus Module description] BUS COM-
MUNICATION FAILURE
[Bus Module description] POWER
FAILURE
[Bus Module description] BATTERY
FAILURE
[Bus Module description] MODULE
TAMPER
[value] NOT ENTERED
[Zone description] BACKUP BAT-
TERY TROUBLE
[Zone description] GROUND FAULT
TROUBLE
[Zone description] HARDWIRE LOOP
TROUBLE
[Zone description] LOW BATTERY
[Zone description] OBSCURITY
TROUBLE
[Zone description] POWER FAILURE
[Zone description] RF JAM TROU-
BLE
[Zone description] SUPERVISORY
FAILURE
[Zone description] TAMPER
[Zone description] TROUBLE
[Zone description] ZONE ACTIVITY
TROUBLE
ARMING ABORTED OR FAILED
AUDIO TROUBLE
AUXILIARY POWER FAILURE
BATTERY IS BAD
BUDDY 1 FAILURE
BUDDY 2 FAILURE
BUDDY 3 FAILURE
BUDDY 4 FAILURE
DELETE A CODE FIRST
ENTER YOUR CODE
ENTRY CLEARED
System trouble condition exits. Check system status.
Bus receiver has failed.
Bus transceiver antenna has been tampered with.
Panel has lost communication with bus device.
Bus device has lost AC power.
Bus device has low battery.
Bus device has been tampered with.
Keypad entry time-out has expired.
Zone has a low backup battery.
Hardwired l oop has a short to ground.
Hardwired loop is open or shorted.
RF sensor has low battery.
Smoke sensor has partial obscurity trouble. This means that the sensor is close to
detecting an alarm, most likely because the sensor is dirty.
Zone has lost AC power.
RF sensor is being jammed by interfering RF signal
Panel has lost communication with RF sensor.
Zone has been tampered with.
Generic/unspecified zone trouble.
Panel has not detected sufficient zone activity or could also indicate a failed sensor.
Panel is unable to arm the system. Check unbypassed open or faulty sensor(s).
Panel has detected a problem with its audio amplifier.
Auxiliary power (12V or 24V) is not OK.
The panel 12 VDC backup battery (s) not charged or ha s failed.
Panel communication with buddy 1 has failed.
Panel communication with buddy 2 has failed.
Panel communication with buddy 3 has failed.
Panel communication with buddy 4 has failed.
No room for new code. Delete an existing code.
Valid access code is needed to proceed.
Invalid or incomplete entry cleared.
Advent® Home Navigator System
29
Page 32
Appendix C: Display Error Messages and Meanings
Message# INVALID Meaning Invalid keypad entry
FLASH MEMORY TROUBLE
GOODBYE
INVALID AUTHORITY
INVALID CODE
INVALID EVENT
LONG RANGE RADIO TROUBLE
MAIN LOW BATTERY
MAIN POWER FAILURE
MAIN POWER IS [description] or
MAIN BATTERY IS [description]
MEMORY CHECKSUM TROUBLE
NEW BUS DEVICE
NO ALARM HISTORY
NO ENTRY
PHONE LINE 1 FAILURE
PHONE LINE 2 FAILURE
PHONE NUMBER 1 COMMUNICA-
TION FAILURE
PHONE NUMBER 1 TEST FAILURE
PHONE NUMBER 2 COMMUNICA-
TION FAILURE
PHONE NUMBER 2 TEST FAILURE
PRINTER TROUBLE
REMOTE PHONE TAMPER
SECOND ENTRY FAILED
SIREN TAMPER
SNAPCARD POWER FAILURE
SNAPCARD LOW BATTERY
SNAPCARD TROUBLE
SYSTEM BUSY
SYSTEM GOODBYE
A flash memory error has been detected. The panel requires service.
Quitting menu mode.
Insufficient access code authority. A different (higher authority) access code is
required.
Invalid access code. Enter valid code to proceed.
An invalid event is being annunciated in event history review.
Panel has lost supervision of long-range radio; long-range radio is missing or faulty.
Panel backup battery is low.
Panel AC power is missing.
Indicates present system AC power status.
Panel has detected a RAM checksum error. Panel should be reset and programming
should be checked.
Panel has detected an unenrolled bus device.
Alarm hist ory buffer (memory) is empty.
Keypad entry time-out ha s ex pir e d.
Phone line 1 has failed.
Phone line 2 has failed.
Panel has failed to communicate with the central station phone number 1 when it
tried to report an event.
Phone test us ing phone number 1 has failed.
Panel has failed to communicate with the central station phone number 2 when it
tried to report an event.
Phone test us ing phone number 2 has failed.
Printer trouble has been detected (printer error, off-line, out of paper, out of ink,
missing).
Panel has detected an unauthorized attempt to access the panel via the remote phone.
Four consecutive invalid access code entries have been detected.
Second entry different than the first.
Voice siren is being tampered with. Wiring is shorted, open, or grounded.
SnapCard AC power is missing.
SnapCard backup battery is low.
Panel has detected a trouble with one of its SnapCards; SnapCard is missing or
wrong type.
System has taken control of (seized) the telephone lines and/or is too busy to
respond now.
System is about to take control of (seize) the telephone lines.
30
Advent® Home Navigator System
Page 33
Appendix D: System Planning Tables
Below are tables to help list programmed options.
Schedules
Part. # Schedule On
Time
11
Off
Time
Duration Normal Holiday AHoliday BTemporary Arming
Table 12: Schedules
Appendix D: System Planning Tables
Daylight
Type
Type
Holiday Schedules
Advent® Home Navigator System
31
Page 34
Appendix D: System Planning Tables
Table 13: Holiday Schedule
Partition # List Holiday # Month Day Normal
32
Advent® Home Navigator System
Page 35
FCC Notices
FCC Part 15 Information to the User
Changes or modifications not expressly approved by Interlogix, Inc. can void the user’s authority to operate the equipment.
FCC Part 15 Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protectio n against interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
q Reorient or relocate the receiving antenna.
q Increase the separation between the equipment and receiver.
q Connect the affected equipment and the panel receiver to separate outlets, on different branch circuits.
q Consult the dealer or an experienced radio/TV technician for help.
FCC Part 68
This equipment complies with Part 68 of the FCC Rules. Located on this equipment is a label that contains, amo ng other inf ormation, the FCC registration number and the ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.
The REN is used to determine the maximum number of devices that may be connected to your telephone line. In most areas,
the sum of all device RENs should not exceed five (5.0).
If this equipment causes harm to the telephone network, the telephone company may temporarily disconnect your service. If
possible, you will be notified in advan ce. When advan ce notice is not practical , you will be n otified as soon as possi ble. You
will also be advised of your right to file a complaint with the FCC.
Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper
operation of your equipment. You will be given advanced notice in order to maintain unin terrupted service.
If you experience trouble with this equipment, please contact the company that installed the equipment for service and repair
information. The telephone company may ask you to disconnect this equipment from the network until the pro blem has been
corrected or you are sure that the equipment is not malfunctioning.
This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to
state tariffs.
Page 36
ITI | 2266 SECOND STREET NORTH | NORTH SAINT PAUL MN | www.interlogixinc.com
©2001 Interlogix,™ Inc. Interlogix is a trademark of Interlogix, Inc. ITI and Advent are registered trademarks of Interlogix, Inc.
Loading...