ITEM Work bench E, Work bench 4 E FIFO, Work bench 4 E User Manual
User guide
Work bench E, 4 E and 4 E FIFO
2
Contents
1.5 CE declaration 5
9. Maintenance and servicing work 14
10. Disassembly and replacement of parts 14
11. Disposal 14
12. Annex 15
12.1 Installation declaration for the table columns 15
12.2 Specification plates 16
1. General safety information 3
1.1 Correct use 4
1.2 Improper use 4
1.3 Personnel qualifications 4
1.4 Warning symbols 4
2. Product description 6
3. Operating data 8
4. Setting up the height-adjustable work bench 8
4.1 Environmental considerations 8
4.2 Levelling the work bench 8
5. Electrical connections for height-adjustable tables 9
6. Start-up 10
6.1 Initialising the table columns when starting up the system for the first time (RESET) 10
7. Functions
7.1 On-time limiter
11
11
7.2 Safety range 11
7.3 Overload detection 11
7.4 Soft start/soft stop 11
7.5 Movement lock 11
7.6 Memory function 11
8. Error messages on the manual controls 13
6.2 Operation 10
7.7 Setting the upper and lower travel limits 12
7.6.1 Moving the table columns to stored heights 11
7.8 Switching between cm / inch 12
3
The details and information in the user guide are provided solely for the
purpose of describing the product and its assembly. The information does not
discharge the user from the obligation to carry out his own assessments and
checks. It is important to bear in mind that our products are subject to a natural
process of wear and ageing.
These notes contain important information that will enable you to use the
product safely and appropriately. When sold, rented out or otherwise passed on
to another party, this product must be handed over with the user guide.
When installing, operating and maintaining the electrical, height-adjustable
work bench, it is important to ensure that all moving elements are secured
so that they cannot be switched on and moved unintentionally. Rotating and
moving parts can cause serious injury! You must therefore read and follow the
safety instructions set out below.
All work on and with the electrical, height-adjustable work bench must be
performed with “safety first” in mind.
Switch off the power to the table columns before carrying out any work on the
electrical, height-adjustable work bench.
Ensure the table columns cannot be switched on unintentionally, e.g. by affixing
warning notices at the activation point or by removing the fuse from the power
supply.
Do not place your hand within the operating range of the electrical, heightadjustable work bench’s moving parts when it is still switched on.
Fit guards and covers to the moving parts of the electrical, height-adjustable
work bench to ensure they are not touched unintentionally.
Observe the regulations pertaining to accident prevention and environmental
protection that apply in the country and place of work where the product is
being used.
Use only item products that are in perfect working order.
Failure to use original spare parts will invalidate the product warranty!
Check the product for obvious defects.
Use the product only within the performance range described in the technical
data.
Ensure that all the safety equipment associated with the product is present,
properly installed and in full working order.
Do not alter the position of safety equipment, circumvent it or render it ineffective.
The electrical, height-adjustable work bench described here corresponds to the
state of the art and takes into account the general principles of safety applica
ble at the time this user guide was published. Nevertheless, failure to observe
the safety instructions and warning notices in this user guide may result in
personal injury and damage to property.
We will assume no liability for any resulting damage or injury. We reserve the
right to make technical changes that represent technical advances. Keep these
installation notes in a place where they can be easily accessed by all users.
Observe the directions contained in the main user guide for a system.
The general safety information applies to the entire lifecycle of the electrical,
height-adjustable work bench.
1. During transportation
Observe the handling instructions on the packaging. Until it is installed, the
product must be stored in its original packaging, protected from moisture and
damage. Ensure that moving parts are secured when in transit and cannot
cause any damage. Suspended loads can fall during transport if load-bearing
equipment is not fit for purpose or is incorrectly secured, thus leading to serious
injuries (including fatal injuries).
Keep clear of suspended loads.
Use lifting tackle with sufficient load-bearing capacity (see delivery paper
-
work for product weight).
Carefully secure lifting tackle.
Attach lifting tackle to the product only at sufficiently stable points.
Always set down the height-adjustable work bench on a level surface.
Observe environmental regulations.
2. During installation
Always deactivate the power to the relevant system part and ensure it is not live
before installing the product and/or plugging it in or unplugging it. Ensure the
system cannot be switched back on. Lay cables and lines in such a way that
they cannot be damaged and do not represent a trip hazard. Avoid areas that
pose slip, trip and fall hazards.
3. During start-up
Allow the product to acclimatise for a few hours before starting it up.
Ensure that the partly completed machine is securely and safely integrated into
the completed machine. Only start up a product that has been installed in full.
4. During operation
Ensure that only persons who have been authorised by the operator have access to the immediate operating area of the height-adjustable work bench. This
also applies when the system is not in operation. It must not be possible to actu
ate moving parts unintentionally. During emergencies, malfunctions or other
irregularities, deactivate the height-adjustable work bench and ensure it cannot
be switched back on. Ensure that nobody can step below suspended loads and
prevent access below the working surface of the height-adjustable work bench.
The height-adjustable work bench is not suitable for lifting people.
5. During cleaning
Close all openings with suitable protective equipment to ensure that cleaning
agents cannot penetrate the system. Do not use aggressive cleaning sub
-
stances. Do not use a high-pressure cleaner when cleaning the system.
6. During maintenance and servicing work
Carry out the prescribed maintenance work at the intervals stipulated in the
user guide. Ensure that no cables, connections or components are detached or
removed while the system is live. Ensure that the height-adjustable work bench
cannot be switched back on.
7. During disposal
Dispose of the product in accordance with the national and international regulations that apply in your country.
1. General safety information
4
The electrical, height-adjustable work bench is a partly completed machine as
defined in the Machinery Directive (2006/42/EC). The electrical, height-adjus
table work bench must only be used in accordance with the technical data and
safety requirements set out in this document. The electrical, height-adjustable
work bench is a technical item of work equipment and is not intended for
private use.
If major alterations are made to the electrical, height-adjustable work bench,
compliance with the Machinery Directive will need to be renewed and the
documentation supplemented accordingly.
The electrical, height-adjustable work bench is a moving device for the separate
raising and lowering of the working surface and accessories.
Internal company requirements and the regulations that apply in the country
where the product is being used must be observed. You must not make any
design modifications to the electrical, height-adjustable work bench yourself.
We will assume no liability for any resulting damage or injury.
You may only install, operate and maintain the electrical, height-adjustable work
bench if:
The electrical, height-adjustable work bench is used only in a fixed, station
-
ary location,
You integrate the electrical, height-adjustable work bench into its surround-
ings in a proper and safe manner. The operator is responsible for ensuring
proper and safe installation,
You have carefully read and understood the installation guide,
You are appropriately qualified,
You are mentally and physically capable of doing so,
You are authorised to do so by your company,
You are using only original equipment from the manufacturer.
Unsafe or inappropriate use of the electrical, height-adjustable work bench runs
a risk of serious injury through crushing and cuts.
Improper use is defined as any use of the product for purposes other than those
authorised in the user guide and under the definition of correct use. We will
assume no liability for any resulting damage or injury.
Assembly, commissioning, operation, disassembly and maintenance work
(including servicing and care) require an adequate knowledge of electrical
and mechanical engineering and an understanding of the relevant technical
terminology. To ensure operational safety, these activities must therefore be
carried out only by a qualified person or by personnel under the instruction and
guidance of a qualified person
A qualified person is an individual who – by virtue of his or her specialist train
ing, know-how, experience and knowledge of pertinent regulations – is able to
assess the work that is assigned to him or her, recognise potential hazards and
put in place appropriate safety measures. A qualified person must comply with
the applicable specialist regulations.
Attention, Warning
Information
1.1 Correct use
1.2 Improper use
1.4 Warning symbols
1.3 Personnel qualifications
5
1.5 CE declaration
Loading...