Bluetooth Headset
Clip Naro 601
User Guide
Contents
Product Specifications ...................................................................................................................................... 1
Clip Naro 601 Overview .................................................................................................................................... 2
Getting Started ................................................................................................................................................... 2
Charging Your Headset .................................................................................................................................... 3
Indicator Light .................................................................................................................................................... 3-4
Pairing Your Headset with a Bluetooth Mobile Phone ............................................................................ 4
Using Your Headset .......................................................................................................................................... 5-7
Resetting Your Headset / Removing the Pairing History ......................................................................... 8
Troubleshooting ................................................................................................................................................ 8-9
Safety Information ............................................................................................................................................ 9-10
Care and Maintenance ..................................................................................................................................... 11-12
Declaration of Conformity ............................................................................................................................... 12
Product Specifications
Bluetooth Specification: v2.1 + EDR Class 2
Bluetooth Profiles Supported: Headset, Handsfree
Range of Frequency: 2.4GHz spectrum
Nominal Charging Time: Within 3 hours
Talk Time*: Up to 6 hours
Standby Time*: Up to 120 hours
Dimensions: 49.8 (L) x 13.7 (W) x 23.2 (H) mm
Weight: 13.1 grams
* may vary due to the user’s habit, different modes of operation, and mobile phone settings.
Clip Naro 601 Overview
1. Multi-function Button (MFB)
• Power On / Off
• Pair with mobile phone
• Answer / End a call
• Last number redials
• Voice dialing
2. Volume / Status Indicator
• Adjust volume
• Reject / Transfer a call
3. Built-in Rechargeable Battery
4. Microphone
5. Buzzer
6. Earpiece
7. USB Charging Socket
Getting Started
To use your Clip Naro 601 Bluetooth headset (“headset”), please follow the steps below:
1. Ensure your headset is fully charged.
2. Pair your charged headset with a Bluetooth-enabled mobile phone.
(fig.1)
7
1
6
5
2
4
3
Charging Your Headset
Indicator Light
Headset Status
• Standby
• Charging (OFF MODE)
• Fully charged (OFF MODE)
• Low battery
• Out of battery
• Charging (STANDBY MODE)*
• Fully charged (STANDBY MODE)*
• Out of Range
• Flash blue
• Solid red
• Solid blue
• Flash red with short beep every minute
• The light turns off
• Double flash red
• Double flash blue
• Solid purple for 5sec then flash blue
Status Indicator Light
The headset comes with a built-in rechargeable
battery. Prior to using the headset for the first
time, it is recommended to fully charge the
battery.
Insert the charger’s plug into the headset’s USB
charging socket and plug the mains charger to
an AC wall outlet or plug to the PC/notebook.
Use only the supplied charger / USB charging cable to charge the headset.
Charging
Socket
USB Charger
Plug
(fig.2)
1
2 3
Pairing Your Headset with a Bluetooth Mobile Phone
1) Ensure the headset is off.
2) To activate the pairing mode, press and hold the headset’s MFB for 8 seconds without
releasing your finger until its status indicator flashes blue and red light alternately.
3) Activate your mobile phone’s Bluetooth, search Bluetooth devices, select “Clip Naro 601” and
enter the passcode “0000”. When the pairing is completed, the headset’s status indicator will
flash blue light rapidly 5 times and you can hear a long beep.
If the pairing cannot be completed within 3 minutes after the pairing mode has been activated,
the headset’s status indicator will flash purple rapidly 5 times and then turns off. Repeat steps 1
to 3 to do the pairing again.
POWER ON Press and hold the MFB for 2 sec Short beep Flash blue light
twice
Using your headset
Function Button Beep / Buzzer
When you turn on your headset for the first time, the headset proceeds into pairing mode, i.e.
the status indicator flashes blue and red alternately, so that you can immediately pair it with
your mobile phone.
When there is 2nd incoming call, press MFB can hold the current call and answer the 2nd
incoming call*
Status indictor
POWER OFF
Incoming call
Answer / End a call Press the MFB once
Press and hold the MFB for 2 sec Long beep
Ringtone through the
earphone and buzzer ON
(depends on buzzer pattern)
Flash red light
and then goes off
Flash purple
Using your headset
Function Button Beep / Buzzer
Triple Point allow simultaneous pairing of the headset with three mobile phones, to pair 3
mobile phones:
1. pair your headset with the 1
st
mobile phone as normal
2. repeat the pairing procedure for the 2
nd
mobile phone
3. repeat the pairing procedure for the 3
rd
mobile phone
4. re-connect the 1
st
and 2nd mobile phone with the headset
when there is incoming call from another phone, press MFB will end the current call and
answer the incoming call
Status indictor
Call Transfer (headset to
mobile phone)*
Press and hold the Volume for 2 sec
Call Transfer (mobile
phone to headset)*
Press MFB once
♦ Charging indication will be delayed for a few seconds if the headset has not been used for a
long time or the battery is drained.
♦ 3 hours are required to fully charge the headset.
♦ The headset remains in standby mode after being turned on.
* Warning: Do not use the headset while it is connected to the charger
Using your headset
Function Button Beep / Buzzer
Choose your favorite buzzer pattern - The buzzer control mode will keep demonstrating the 4
patterns for 2 min. You can press and hold Volume for 2 sec to exit the demonstration any time.
Status indictor
Flash blue and purple
alternately
Flash blue and purple
alternately
Enter buzzer control mode
Buzzer mode 1
Press and hold the Volume for 2 sec
Buzzer OFF
Buzzer mode 2 Buzzer pattern 1
Buzzer mode 3 Buzzer pattern 2
Buzzer mode 4 Buzzer pattern 3
Short beep
Flash purple 2 times
for the pressed button
Confirm Buzzer mode
* Subject to mobile support
In buzzer control mode, press
Volume once
Long beep
4
Indicator Light
5
Say the voice tag as soon as you hear the short beep and you must have recorded the voice
tag into your mobile phone.
Adjust Volume Press Volume Short beep at max. volume
Voice Dialing* In standby mode, Press the MFB once Short beep
Last no. Redial* In standby mode, double click MFB
Reject incoming call* Short beepPress and hold the Volume for 2 sec
6
Mobile away alert is an advance feature to alert you when your mobile phone is away by 10
meters. It remind you not to leave behind your mobile phone unintentionally and avoid your
mobile phone being stolen. You will hear 20 short buzzers when alert is ON.
Mobile away alert Enable
(Factory default Off)
Press and hold the Volume And
MFB for 2 sec
2 short beep
Flash purple 3 time
7
Mobile away alert Disable Press and hold the Volume And
MFB for 2 sec
Short beep Solid purple for 5 sec
Stop Buzzer Alert Press MFB
Loading...