MyVoice 610
Bluetooth Headset
User Guide
Paring Mode (Off Mode):
Holde 8 sec. Pairing Mode
Hold the volume up/ down and see the status indicator to check the battery status.
Solid Green = Over 3.5 Hours Talk Time
Flashing Green = Below 3.5 Hours Talk Time
Flashing Red = Below 45 Minutes Talk Time
7
5
6
1. Multi-function Button (MFB)
• Power On / Off
• Pair with mobile phone
• Answer / End a call
• Call waiting
1
2
3
4
2. Status Indicator
3. Micro-USB Charging Socket
4. Built-in Microphone
5. Volume Up
• Adjust Volume Up
• Reject / Transfer a call
6. Volume Down
7. Lock Key
Charging Your Headset
The headset comes with a built-in rechargeable battery. Prior to using the headset for
the first time, it is recommended to fully charge the battery.
Insert the charger’s plug into the headset’s USB charging socket and plug the mains
charger to an AC wall outlet or plug to the PC/notebook.
Use only the supplied charger / USB charging cable to charge the headset.
Quick Charge
Charging the headset for 15 minutes can provide 1 hour talk time.
Headset Status Status Indicator Light
• Charging (OFF MODE)
• Fully charged (OFF MODE)
• Low battery
• Solid red
• Off
• Blinking red 3 times with beep
• Charging (STANDBY MODE)*
• Fully charged (STANDBY
MODE)*
♦ 3 hours are required to fully charge the headset.
*Warning: Do not use the headset while it is connected to the charger.
Pairing Your Headset with a Bluetooth Mobile Phone
1) Ensure the headset is in OFF and unlock mode.
2) To activate the pairing mode, press and hold the headset’s MFB for 8 seconds. The
status indicator will flash blue and red alternately.
3) Activate your mobile phone’s Bluetooth, search Bluetooth devices, select
“MyVoice 610” and enter the passcode “0000”. When the pairing is completed, the
headset’s status indicator will flash blue rapidly 5 times and you can hear a long beep.
every 5 minute
• Solid red
• Off
Basic Operation
Function Button Beep / Buzzer Status indictor
POWER ON Press and hold the Short beep Blinking Blue for 3
MFB for 3 seconds times
When you turn on your headset for the first time, the headset proceeds into pairing
mode, i.e. the status indicator flashes blue and red alternately, so that you can
immediately pair it with your mobile phone.
POWER OFF Press and hold the
Long beep Red, Blue light for 2
MFB for 3 seconds
Incoming call Ringtone through
the earphone and
buzzer ON
Answer / End a
call
Reject incoming
call*
Press the MFB
once
Double click VOL
Up
Short beep
Battery Check At Standby mode,
>75%
press VOL Up or
VOL Down for 2
seconds
Lock Keylock At any mode, slide
the key lock to
Lock position
seconds
Blinking purple
Green
15%-74%
<15%
Blinking
green
Blinking
Red
Unlock Keylock At any mode, slide
Short beep
the key lock to
Unlock position
In Lock Mode, call still can be answered /rejected by normal operation.
Multi-point allows simultaneous pairing of the headset with two mobile phones, to
pair 2 mobile phones:
1. pair your headset with the 1st mobile phone as normal and then switch off
2. repeat the pairing procedure for the 2nd mobile phone
3. re-connect the 1st mobile phone with the headset via the phone menu
when there is incoming call from another phone, press MFB will end the current call
and answer the incoming call
i.Tech Bluetooth headset is designed to work with Bluetooth devices. Due to large
variability between different Bluetooth devices from different manufacturers,
interoperability between the headset and all Bluetooth-enabled products is not
guaranteed.
Product Specifications
Bluetooth Specification: v2.1 + EDR Class 2
Bluetooth Profiles Supported: Headset, Handsfree
Range of Frequency: 2.4GHz spectrum
Nominal Charging Time: Within 3 hours
Talk Time*: Up to 5 hours
Standby Time*: Up to 130 hours
Dimensions: 52 (L) x 17 (W) x 5.5 (H) mm /
2.0 (L) x 0.67 (W) x 0.22 (H) inches
Weight: 12 grams / 0.42 ounces
* may vary due to the user’s habit, different modes of operation, and mobile phone
settings.
Detail Operation
Indicator Light
Headset Status Status Indicator Light
• Low battery
• Out of battery
If the pairing cannot be completed within 3 minutes after the pairing mode has been
activated, the headset’s status indicator will flash blue rapidly 5 times and you can
hear 3 short beeps. Then the headset turns off. Repeat steps 1 to 3 to pair both devices
again.
Adjust Volume Press VOL Up or
VOL Down
Voice Dialing* In Standby Mode,
press MFB and
VOL Down
Say the voice tag as soon as you hear the short beep and you must have recorded the
voice tag into your mobile phone.
• Blinking red 3 times with beep every
5 minute
• The light turns off
Short beep at max.
or min.
Short beep
Last no. Redial* In Standby mode,
double click MFB
Call Transfer
(headset to mobile
phone)*
Call Transfer
Press and hold the
VOL UP for 2
seconds
Press MFB once
(mobile phone to
headset)*
Call Waiting allows you to hold up the current caller and pick up the second caller.
To pick second call, press MFB once.
To reject second call, press VOL for 2 seconds.
To swap call, double press MFB.
To terminate current and swap to second call, press MFB once.
Resetting Your Headset / Removing the Pairing History
You may reset the headset to its default settings. Resetting will also remove the
pairing history of your headset with the mobile phone.
1. During OFF mode, hold the VOL UP key and plug charging cable into the charging
socket. The status indicator flashes Blue twice.
2. Release the Volume key.
3. The status indicator will stay flashing blue and the headset is reset.
You may also reset the headset to its default settings by hardware reset.
1. Plug charging cable into the charging socket.
2. Hold VOL and MFB at the same time.
3. The headset is reset.
Noise cancellation
Multipoint
Quick Charge
Aluminum case
Audio Streaming
Wind & noise reduction
Enhanced HD Voice
Universal Adaptor enables VOIP calls via the headphones
3.5mm jack for listening music from your smart phone
Inline microphone with one touch button for mobile call & music
Adjustable & durable headband
Loading...