i.Tech MyVoice 306 User Guide

FRONT

MyVoice 306

Bluetooth Headset

User Guide

Contents

Product Specifications
MyVoice 306 Overview
Getting Started
Charging Your Headset
Pairing Your Headset with a Bluetooth Mobile Phone
Using Your Headset
Factory Reset
Troubleshooting
Safety Information
Care and Maintenance
Declaration of Conformity

MyVoice 306 Overview

2

6

1

5

3

(fig.1)

Getting Started

1. Multi-function Button (MFB)

4

• Power On / Off

• Pair with mobile phone

• Answer / End a call

2. Volume

• Adjust volume

• Reject / Transfer a call

3. Status Indicator

4. Microphone

5. Micro USB Charging Socket

6. Speaker

To use your MyVoice 306 Bluetooth headset (“headset”), please follow the steps below:

1. Ensure your headset is fully charged.

2. Pair your charged headset with a Bluetooth-enabled mobile phone.

Charging Your Headset

The headset comes with a built-in rechargeable
battery. Prior to using the headset for the first
time, it is recommended to fully charge the
battery.
Insert the charger’s plug into the headset’s
charging socket (see fig.2) and plug the mains
charger to an AC wall outlet or plug to the
PC/notebook.

Use only the supplied charger / USB charging cable to charge the headset.

Charging
Socket

3
4
5
5-7
7
8-10
11
12-13
13-14
15-16
17

Product Specifications

Bluetooth Specification: v2.0 + EDR Class 2
Bluetooth Profiles Supported: Headset & Handsfree
Range of Frequency: 2.4GHz spectrum
Nominal Charging Time: Within 3 hours
Talk Time*: Up to 6 hours
Standby Time*: Up to 150 hours
Dimensions: 43.5(L) x 21(W) x 11.5(T) mm
Weight: 14 grams

* may vary due to the user’s habit, different modes of operation, and mobile phone

settings.

2 3 4 5

USB charging
cable

BACK

Charging Your Headset Charging Your Headset

Indicator Light

Headset Status Status Indicator Light (fig.1)

• Standby Mode (Operating)

• Standby Mode (Out of Range)

• Off Mode Charging

• Off Mode Fully Charged

• Standby Mode Charging

• Standby Mode Fully Charged

• Low battery

• Out of battery

♦ Charging indication will be delayed for a few seconds if the headset has not been used for a long

time or the battery is drained.

♦ 3 hours are required to fully charge the headset.

• Flashing Blue

• Flashing PURPLE 4 times each 15 sec until reconnect

(goto standby after 10mins)

• Long Red

• Off

• Flashing PURPLE with RED Led ON

• Same as standby

• Flashing Red

• The light turns off

Factory Reset

You may reset the headset to its default settings. Resetting will also remove the pairing history of your
headset with the mobile phone.

1. Switch off the headset

2. Hold the volume UP key and plug charging cable into the charging socket. The status indicator will
flash purple twice.

3. Release the volume key.

You may also reset the headset to its default setting by hard reset.

1. Plug the charging cable into the charging socket

2. Hold MFB and Volume key at the same time

3. Release both MFB and Volume UP key, the indicator will stay red again and the headset is reset

i.Tech Bluetooth headset is designed to work with Bluetooth devices. Due to large variability between
different Bluetooth devices from different manufacturers, interoperability between the headset and all
Bluetooth-enabled products is not guaranteed.

Talk and Standby Time

A fully charged battery can offer up to 6 hours of talk time and up to 100 hours of standby time. The
headset remains in standby mode after being turned on.

Pairing Your Headset with a Bluetooth Mobile Phone

1) Ensure the headset is off.

2) To activate the pairing mode, press and hold the headset’s MFB without releasing your finger until its
status indicator blinks red/blue.

3) Activate your mobile phone’s Bluetooth, search Bluetooth devices, select “MyVoice 306” and enter
the passcode “0000”. When the pairing is completed, the headset’s status indicator will flash blue
light rapidly five times.

If the pairing cannot be completed within three minutes after the pairing mode has been activated, the
headset’s status indicator will blinking purple 5 times and then turns to standby mode. Repeat steps 1
to 3 to pair the devices again.

6 7 8 9 10

Troubleshooting

I can hear crackling noise.

To receive the best audio quality, it is recommended to wear your headset on the same side of
the body as your mobile phone.

I can't hear anything in my headset.

• Ensure the headset is turned on and is properly charged.

• Ensure the headset is properly paired with the mobile phone.

• Make sure that the mobile phone is connected with the headset – if it does not connect,
either refer to the mobile phone's Bluetooth menu or by pressing the MFB once (see “Using
Your Headset” and “Pairing Your Headset with a Bluetooth Mobile Phone”).

I can't connect my headset with my mobile phone.

• Ensure your headset is turned off and is properly charged.

• Ensure the headset is properly paired with your mobile phone.

• Ensure your mobile phone’s Bluetooth feature is activated. Please refer to your mobile

phone user guide for specific instruction.

• Ensure the headset is within ten metres range of your mobile phone and there are no

obstructions, such as walls or other electronic devices in between.

If the above steps do not solve your problem, please recharge the headset and remove your

mobile phone’s battery for a while.

11 12 13 14

Using your headset

Function Button Audio Status indictor

POWER ON Press and hold

When you turn on your headset for the first time, the headset proceeds into pairing
mode, i.e. the status indicator blinks green, so that you can immediately pair it with
your mobile phone.

POWER OFF Press and hold the

Incoming call Ringtone on earphone Quick flashing purple light

Answer a call Press the MFB once

End a call Press the MFB once

the MFB

MFB for 2 seconds

a Short beep Flash blue light 3 times

a Long beep Red light for two

seconds and then the
light goes off

Flashing blue light

Flashing blue light

Troubleshooting (cont’d)

I can’t turn off the headset or the headset does not respond

• You may do a “hardware reset” on your headset if you can’t turn it off or it doesn’t respond.

Safety Information

• Check and observe local laws regarding the use of a mobile phone and a headset while

driving. If you use the headset while driving, ensure your full attention and focus. It is your
responsibility to drive safely. Consider to pull off the road before making or answering a call.

• Never leave your headset above any air bag deployment area inside your car as serious

injury may result when an air bag deploys.

• Never allow children to play with the headset – small parts may be of choking hazard.

• Observe all signs and displays that require an electrical device or RF radio product to be

switched off in designated areas. These could include hospitals, blasting areas, and
potentially explosive atmospheres.

• Turn off your headset prior to boarding an aircraft. Do not use your headset inside an

aircraft.

Using your headset (cont’d)

Function Button Audio Status indictor

Adjust Volume Press the Volume Key

Voice Dialing* Press the MFB once a short beep

Say the voice tag as soon as you hear the short beep and you must have recorded the
voice tag into your mobile phone.

Reject a call* Press and hold the

once to
increase/decrease by 1
step (Total 6 levels)

Double click the MFBLast no. Redial*

Volume Key for 2
seconds

a short beep

Flashing blue light

Flashing blue light

Flashing blue light

Flashing blue light

Safety Information (cont'd)

• To prevent damage to your hearing, please do not set the listening volume too high.

• Do not attempt to modify the headset.

• Do not keep the headset near a wash basin or other wet places.

• Do not use the headset outdoors in the rain.

• Do not use the headset in stormy weather.

• Do not clean the headset while it is being charged. Always disconnect the charger from the

headset before cleaning.

• Do not attempt to force open the built-in battery.

• Only charge the headset’s built-in battery in accordance with the instructions described in

this user guide.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

Using your headset (cont’d)

Function Button Audio Status indictor

Call Transfer
(headset to
mobile phone)*

Call Transfer
(mobile phone
to headset)*

While speaking, press
and hold the volume
Key for 2 seconds

While speaking,
press MFB once

Flashing blue light

Flashing blue light

* Subject to mobile support

Care and Maintenance

Headset

• Turn off your headset before placing it in your pocket or bag. If the MFB is accidentally

depressed, your mobile phone may place an unintended call.

• Do not expose the headset to liquid, moisture or humidity, or rain as it is not waterproof.

• Do not use abrasive cleaners to clean the headset.

• Do not expose the headset to extremely high or low temperatures.

• Do not leave the headset in direct sunlight for an extended period of time.

• Do not leave the headset near open flames such as cooking burners.

• Do not dispose of the headset in a fire, as it will result in explosion.

• Do not bring the headset into contact with any sharp objects, as this will cause scratches and

damages.

• Do not stick anything inside the headset, as this may damage internal components.

• Do not attempt to disassemble the headset as it does not contain serviceable components.

• If you do not plan to use the headset for a long period, please store it in a dry place that is

free from extreme temperatures and dust.

• Avoid charging the headset in extremely high or low temperatures.

• Dispose of the battery and the headset according to local regulations. Do not dispose of

them as household waste.

15

Care and Maintenance (cont’d)

Built-in Battery

• Do not attempt to replace the headset’s battery as it is in-built and is not changeable.

• Dispose of the battery according to local regulations. Do not dispose of the battery as

household waste.

• Charge the battery in accordance with the instructions supplied with this user guide.

Charger

• Use only the charger supplied by the headset’s original manufacturer to charge the headset.
Other chargers may look similar but using them could be dangerous and could damage the

headset.

• Do not attempt to disassemble the charger as it may expose you to dangerous voltages or

other risks. Incorrect reassembly can cause electric shock when the headset is subsequently
used.

• Do not use the charger outdoors or in damp areas.

Declaration of Conformity

We, i.Tech Dynamic Limited, declare that the following product:
Product Name: i.Tech MyVoice 306
Model No.: C51-B306-XX
is in conformity with the following essential requirements of Council Directive 1999/5/EC (referred
to as R&TTE Directive): Article 3.1a, 3.1.b and 3.2. and the product is manufactured in accordance
with Annex II of the above directive.
A copy of the Declaration of Conformity can be found at http://www.itechdynamic.com.

Notes on Environmental Protection

After the implementation of the European Directive 2002/96/EU in the national legal system, the
following applies: Electrical and electronic devices must not be disposed of with domestic waste.
Consumers are obliged by law to return electrical and electronic devices at the end of their service
lives to the public collection points that are set up for this purpose or designated points of sale.
However, such details are defined by the national law of the respective country. This symbol on
the product, the instruction manual or the packaging indicates that the product is subject to these
regulations. By recycling, reusing the materials, or other forms of utilizing old devices, you are
making an important contribution in protecting our environment.

16 17 18 19

Federal Communications Commission (FCC) Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

15.21
You are cautioned that changes or modifications not expressly approved by the part

responsible for compliance could void the user’s authority to operate the equipment.

15.105(b)
This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:

Federal Communications Commission (FCC) Statement

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

2009 Hutchison Harbour Ring Enterprises Limited
All rights in this publication are reserved and no part may be reproduced without the prior written
permission of the publisher. The contents of this publication are believed to be correct at the time
of going to press, but any information, specifications, products or services mentioned, and product
I.D. shown may be modified, supplemented or withdrawn without further notice.
The Stylized i.Tech logos are trademarks owned by Hutchison Harbour Ring Enterprises Limited or
its affiliates. All other trademarks or registered trademarks belong to their respective owners.

®

Bluetooth

and the Bluetooth logos are trademarks owned by Bluetooth SIG, Inc, USA and licensed
to i.Tech Dynamic Limited.
i.Tech declares under our sole responsibility that the headset is in conformity with the provisions of
the following Council Directives: 1999/5/EC

12/2009

Dispose of the packaging and this product in accordance

with the latest provisions.

S3J-51A306-01-F

20