Non-Touch True Display LCD Monitor
User Manual
Installation Guide
7” True Display LCD Monitor (USB Interface)
MODEL: KKW700B
i-Tech Company LLC
TOLL FREE: (888) 483-2418
EMAIL: info@itechlcd.com
WEB: www.iTechLCD.com
UUsseerr MMaannuuaall // IInnssttaallllaattiioonn GGuuiiddee
77"" SSeeccoonndd DDiissppllaayy ((UUSSBB iinntteerrffaaccee))
It will cause malfunction if the monitor is operating with incorrect power voltage.
Do not exposure this unit in the rain or moisture environment to reduce the risk of fire or electric
shock.
Content:
I. FCC Warning Statement................................................................................ 2
II. Introduction ................................................................................................... 3
Features............................................................................................................................... 3
Unpacking the monitor ......................................................................................................... 3
III. Installation...................................................................................................... 4
Control Buttons .................................................................................................................... 6
IV. Installation Guide .......................................................................................... 7
V. Troubleshooting.......................................................................................... 16
VI. Mechanical dimension................................................................................ 18
VII. Product General Specification ................................................................... 19
Warning!
2
I. FCC Warning Statement
WARNING
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
Notice:
(1) A Unshielded-type power cord is required in order to meet FCC emission limits and also to
prevent interference to the nearby radio and television reception. It is essential that only the
supplied power cord by used.
(2) Use only shielded cables to connect I/O devices to this equipment.
(3) Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
3
1
2
3
II. Introduction
The 7" Second Display is color TFT LCD monitor, with compact and ecological design.
The power consumption is only 2.5W with LED backlight.
Features
- Optimal display resolution 800 * 480
- No ventilation hole design
- Light weight, only 500g physically
- Packing box to be recycled as a free magazine holder
- VESA 75 * 75 mm wall mount standard
Unpacking the monitor
- Put the monitor on a clean surface, make sure the box in upright position.
- Remove packing materials from inside of box.
Check accessory
Please make sure all the accessory are included:
1. USB Cable
2. Driver CD
3. Wall Mount Kit (Option)
4
III. Installation
To PC To Wall
Stand Alone:
1. Assemble pole and stand base 2. Remove 4 screws of metal base
3. Pass USB cable through the pole 4.Pass USB cable through the hinge
cover
5
5. Install USB cable to monitor 6...Install hinge cover to monitor with 4
screws
7. Install monitor set to pole 8. Install metal plate to base
9. Installation complete
6
Control Buttons
▲UP / ▼DOWN key：When adjustment item is selected, the two keys are defined to
decrease or increase the value of brightness.
▼ ▲
7
IV. Installation Guide
PC requirements
USB Monitor software can be used on PCs, from Notebooks, Notebooks/Laptops to Desktops.
The driver will run on processors ranging from Atom N270 based PCs, basic single Core CPUs,
and of course the latest Dual, Quad Core and Core i3/i5/i7 CPUs.
The performance of the software is dependent upon the processing power available, as well as
the Operating system in use. More capable systems offer higher performance.
DisplayLink software is available for PCs running one of the following Windows Operating
Systems:
Windows 7 (32-bit or 64-bit)
Windows Vista with Service Pack 1 or 2 (32-bit or 64-bit)
Windows XP Home or Professional (including Tablet edition) with Service Pack 2 or 3
Windows 2000 with Service Pack 4
Note: 64-bit editions of XP are not supported. No Windows Server editions are supported.
Mac OS X support can be found at http://www.displaylink.com/mac
Recommended typical system requirements are:
Windows 7
For Windows 7, the Windows Experience Index (WEI) is a useful measure of hardware level.
The WEI is accessible from Computer > Properties, or from Control Panel > System.
The recommended typical hardware requirements for the PC are:
WEI score of at least 3 in the ‘Graphics; Desktop performance for Windows Aero’
category.
Overall WEI scores of at least 3 as recommended by Microsoft.
At least one USB 2.0 port.
30 megabytes (MB) of free disk space.
Computer screen for use with the DisplayLink device, if it is not integrated.
Network access for software downloads, or access to a CD-ROM drive.
Windows Vista
For Windows Vista, the Windows Experience Index (WEI) is a useful measure of hardware
level. The WEI is accessible from Computer > Properties, or from Control Panel > System.
The recommended typical hardware requirements for the PC are:
WEI score of at least 3 in the 'Graphics; Desktop performance for Windows Aero'
category.
Overall WEI score of at least 3 as recommended by Microsoft.
At least one USB 2.0 port
30 megabytes (MB) of free disk space.
8
Computer screen for use with the DisplayLink device, if it is not integrated.
Network access for software downloads, or access to a CD-ROM drive.
If the PC specification is below this, performance will be lower (or CPU loading higher than
acceptable).
Windows XP/2000
For 1-2 monitors, business usage, productivity target. This may not provide full frame
rate DVD playback at full screen.
o 1.2GHz Single Core CPU
o 512MB memory
For 3 monitors where 1 could run DVD video while also targeting
productivity and business apps. Will support only 1 video of DVD resolution at full
screen:
o 1.6GHz CPU
o 1GB memory
For 6 screens where 1 screen can run full screen DVD video:
o 1.8GHz Core Duo
o 1GB memory
At least one USB 2.0 port.
30 megabytes (MB) of free disk space.
Computer screen for use with the DisplayLink device, if it is not integrated.
Network access for software downloads, or access to a CD-ROM drive.
Graphics Card Support (Windows Vista/Windows 7)
On Windows Vista and Windows 7, DisplayLink software interacts closely with the primary
graphics card. DisplayLink support and test a single graphics card (GPU) installed in a PC.
All major GPU vendors Intel, ATI, NVidi and Via.
Issues may be found with PCs with multiple graphics cards, or other graphics card
combinations, and DisplayLink software. The following documents the combinations of
testing and known configuration support.
Vista/Windows 7 on version 5.2
Switchable Graphics (ATI/Intel)
Untested on Vista may be used at user’s own risk
On Windows 7 unsupported
Hybrid Graphics / Hybrid SLi / Hybrid Crossfire
Unsupported
SLi machine in SLi mode:
Untested on Vista may be used at user’s own risk
On Windows 7 unsupported
SLi machine in non-SLi mode (i.e. with 2 or more identical GPUs):
9
Unsupported
Crossfire
Unsupported
Other machines with 2 GPUs where only 1 is active at once – reboot needed to switch
Supported
10
Graphics Card Support (Windows 2000/XP)
All graphics cards are supported on Windows 2000/XP.
Supported Languages
The following languages are supported in version 5.2, on all supported operating systems:
Arabic
Bahasa Indonesian
Bulgarian
Chinese (Traditional)
Chinese (Simplified)
Croatian
Czech
Danish
Dutch
English
Finnish
French
Greek
German
Hungarian
Italian
Japanese
Korean
Norwegian
Polish
Portuguese
Russian
Slovak
Slovenian
Spanish
Swedish
Turkish
Unsupported languages default to English.
11
Installing the USB Monitor Software
1. Insert CD into the CD-ROM drive. Click "USB Monitor Driver"
2. Click "I Accept".
3. The progress window appears, as shown in the figure below.
4. If you connect your USB monitor to your PC, it recognizes the monitor and the "Found
New Hardware" wizard is displayed, as shown in the figure below.
• Make sure to connect the USB cable and begin the installation after your PC has booted.
• The Setup program requires about one minute for the installation. If you turn the power
off or remove the USB cable while the Setup program is running, it may cause an error
with the PC or the Windows operating sys-tem.
• The optimal resolution for this USB monitor is 800x600.
12
When setup is finished, a monitor icon is created in the system tray at the bottom of the
monitor screen, and the information for the installed USB monitor is displayed.
5. When the installation is completed, configure the following settings to use multiple
monitors.
(1). Right-click on the “Windows Desktop” and select “Properties” from the displayed menu.
The “Display Properties” window appears.
(2). Select the “Settings” tab. A list of connected USB monitors is displayed.
(3). Arrange the monitors displayed in the 'Display Properties' window in the order they are
actually used.
13
(4). Then click "OK" button.
Configuring the 8.4" USB Monitor Display Information
1. When the driver setup for the USB monitor is finished, a monitor icon is created in the
system tray at the bottom of the monitor screen.
2. Click the monitor icon to display a list of connected USB monitors. Select the monitor for
which you want to configure the display settings. You can configure the "Screen
Resolution”, "Color Quality" and "Screen Rotation" settings for your monitor.
Checking the configuration
After the installation, you can check the configuration by following these steps.
1. Right-click “My Computer”, and select “Properties” - “System Properties” - the “Hardware
tab”.
14
2. Click “Device Manager”.
3. A list of the installed device will be displayed, as shown in the figure below.
- The Initial Screen Settings after Installing the Program
• Applicable mode: Extend mode
15
• Mode position: To the right of the primary screen
• Mode rotation: 0°
Restrictions on the 7” USB Monitor
Supported OS (Operating Systems)
• Windows XP
- Service Pack 1 or earlier: Unsupported
- Service Pack 2 or later: Supported
• Windows 2000
- Service Pack 3 or earlier: Not Supported
- Service Pack 4 or later: Supported
• Windows Server 2003: Not Supported
• Windows Vista: Supported.
To check the information on the operating system of your PC, right-click “My
Computer” on the “Windows Desktop” and select “Properties” from the displayed menu.
Check the information in the “General” tab of the “Computer Properties” window.
1. Because this USB monitor is recognized as a USB device, the DOS screen that
appears for general monitors when a PC is booting up is not displayed.
2. You cannot use the USB monitor for software using 3D hardware acceleration.
- Real Player (Expansion mode is not supported.)
- For most 3D games
- Programs running on the base of Direct X
3. Supported movie programs
- Power DVD
- Win DVD (Version 5 onwards)
- Windows Media Player (Version 10 or later is supported.)
- VLC
4. This monitor does not support the MagicTune program.
- The MagicRotation function may not function normally.
- If the MagicTune program is installed on your PC, it may not be compatible with
this monitor.
5. The USB monitor may not work normally with USB 1.0.
6. If the graphics card of your PC does not support WDDM, the extended mode may
not be available in Windows Vista.
Example) Some versions of the Matrox Card
16
V. Troubleshooting
Check List
Note
Before calling for assistance, check the information in this section to see if you can
remedy any problems yourself. If you do need assistance, please call the phone number
on the In-formation section or contact your dealer.
There is no image on the screen. I cannot turn on the monitor.
Q: Check whether the USB cable is connected correctly. Check whether the USB driver
is installed.
A: The USB monitor is recognized as a general USB device on a PC. If you turn the
monitor on or off quickly and repeatedly, a USB device problem may occur. Refer to
the USB device Troubleshooting section on the Microsoft customer support website.
1. Right-click the “My Computer” and click on “Properties”
2. The Device Manager is displayed.
3. From the “Action” menu, click ”Scan for hardware changes”. Reboot your PC.
The screen of the USB monitor freezes.
Q: Check the “Hardware acceleration” setting for your USB monitor in the “Display
Prop-reties” window.
A: Set the “Hardware acceleration” value to “Full”.
For more information on how to configure the settings, click here.
1. Right-click the “Windows Desktop” and click on “Properties”.
2. The “Display Properties” window appears.
Select the “Settings” tab and click on “Advanced”.
3. If the “Properties” window for your monitor is displayed, select the “Troubleshoot”
tab. Move the “Hardware acceleration” slide to “Full”.
My USB monitor is connected but the screen is blank.
Q: Does the Auto Installation program run when your USB monitor is connected?
A: Install the "USB Monitor Driver" from the provided CD. For more information on how
to install the driver, refer to "Installation and Installation Guide".
I have connected the USB monitor but it does not boot up...
Q: For the One-Board Type computer which uses an i815 chipset motherboard, change
the Legacy USB support option to [Disabled] in the BIOS Setup menu and reboot
the computer.
A: (Example) Phoenix BIOS
If you turn on the computer, the ”Press F2 to enter SETUP” message is displayed on
the bottom of the screen. Press [F2] to display the BIOS Setup menu.
17
Q & A
Q: How I can clone or extend screen mode?
A: Open the”Display Properties” window and select the “Settings” tab,
Q: How can I remove the “USB Monitor Installation Program” completely?
A: Click “Add/Remove Programs” in the “Control Panel”. A list of “currently installed
programs” is displayed.
Select “DisplayLink Graphics” from the list and click “Remove”.
Q: The screen size of the USB monitor is larger than the actual monitor size.
A: If the primary monitor has a high resolution, screens are expanded beyond the
recommended resolution in Clone mode (USB monitor).
Q: The screen size of the USB monitor is smaller than the actual monitor size. The
screen is centered on the monitor.
A: If the primary monitor has a high resolution, screens are smaller than the
recommended resolution in Clone mode (USB monitor).
Q: I disconnected or turned off my USB monitor but my PC still displays the old monitor
information in the Display Properties window.
A: The deactivated USB monitors are such that the power to them is turned off or their
USB cables are disconnected. To remove this information, you have to remove the
“DisplayLink Graphics” program from “Add/Remove Programs” in the “Control
Panel”.
If you remove the program you cannot use all the connected USB monitors.
If you want to use the USB monitor again, you have to setup the installation program
again.
Q: Icons and photos are broken or jagged in Clone mode (USB monitor).
A: This occurs because Windows does not send the screen updating information to
Clone mode if Extended mode is active on a single PC.
We recommend using the monitor in Extend mode.
Note
Before calling for assistance, check the information in this section to see if you can
remedy any problems yourself. If you do need assistance, please call the phone number
on the Information section or contact your dealer.
18
VI. Mechanical dimension
19
VII. Product General Specification
Model 7" Second Display
Color Black
Display Area 153.6 * 86.64 mm
Optimal Resolution 800 * 480 (WVGA)
Brightness 100 cd/m² (typ)
Contrast Ratio 500:1(typ)
Response Time 25 ms (typ)
LCD Viewing Angle(L/R/U/D) 70 / 70 / 50 / 60
Input Video signal connector USB B Type
Power consumption 500mA/2.5W
Input Frequency Horizontal: 31.5-60.2 kHz ; Vertical : 56.3Hz~75Hz
Power supply DC 5V +/- 5%
Temperature Operating : 0℃~40℃ ; Storage : -10℃~50℃
Weight 500g (net)
Physical Dimension 192 * 115 * 34.5 mm
Approvals CE, FCC, BSMI
Wall Mount VESA 75 * 75 mm
Optional item
Color Black
Wall Mounting Bracket
Stand Base 3" or 7" pole + Base
*Product specification to be changed without prior notice
*Made In Taiwan
Loading...