i.Tech i.VoicePRO Bluetooth Clip Headset User Manual

Contents

i.VoicePRO

TM

Bluetooth Headset

Product Specifications

Bluetooth Specification: v2.1+EDR class 2
Bluetooth Profiles Supported: Headset and Handsfree

Range of Frequency: 2.4GHz Spectrum
Operating Distance: 10 meters
Charging Time: Within 3 hours
Talk Time*: Up to 5 hours
Standby Time*: Up to 100 hours
Dimensions: 63 (L) x 16.5 (W) x 9.8 (H) mm
Weight: 12 grams

* May vary due to users’ operation mode and mobile phone settings

User Guide

Product Specifications
i.VoicePRO

TM

Overview
Charging Your Headset
Pairing Your Headset with a

Bluetooth Mobile Phone

Pairing Your Headset with Two Mobile Phones (Multipoint)
Using Your Headset
Resetting Your Headset / Removing the Pairing History
Troubleshooting
Safety Information
Care and Maintenance

i.VoicePROTM Overview

1

2

3

4

5

6

7

2
3
4-5
5
6
6-8
9
10
11-12
12-14

1. Noise Filter Button

2. Status Indicator

3. Volume Key

4. Speaker

5. Multi-function Button (MFB)

6. Microphones

7. USB Charging Socket

1

Right ear Left ear

2 3

Getting Started

Before using your i.VoicePRO (“headset”) for the first time, please ensure that

1. the headset is fully charged;

2. the fully charged headset must be paired and connected with a Bluetooth mobile

phone.

Charging Your Headset

The headset comes with a built-in rechargeable battery. Prior to using the headset for
the first time, you are recommended to fully charge the battery.

USB Charging Socket

Use only the supplied charger to charge the headset.

Charging Your Headset (cont’d)

Status Status Indicator Audio

• Charging • Red light

• Fully charged • Blue light

• Low battery • Flashing red light • a short beep every 1 minute

• Out of battery • The light goes off

♦ 3 hours are required to fully charge the headset.
♦ Charging indication will be delayed for a few seconds if the headset has not been used

for a long time or the battery is drained.

Pairing Your Headset with a Bluetooth Mobile Phone

1) Ensure the headset is off.

2) To activate the pairing mode, press and hold the headset’s MFB for 8 seconds without

releasing your finger until its status indicator flashes blue and red light alternately.

3) Activate your mobile phone’s Bluetooth, search Bluetooth devices, select “i.VoicePRO”

and enter the passcode “0000”. If your mobile phone supports Bluetooth v2.1 “Simple
Pairing” function, no passcode is required. When the pairing is completed, the headset’s

status indicator will flash blue light rapidly five times.
If the pairing cannot be completed within three minutes after the pairing mode has been
activated, the headset’s status indicator will flash purple rapidly five times and then turns

4

off. Repeat steps 1 to 3 to pair both devices again.

5

Pairing Your Headset with Two Mobile Phones (Multipoint)

i.VoicePRO supports a Multipoint function to allow simultaneous pairing of the
headset with two mobile phones.

1. Follow the pairing procedure as instructed in “Pairing Your Headset with a

Bluetooth Mobile Phone” to pair the headset with the first mobile phone.

2. Repeat the pairing procedure for the second mobile phone.

3. On the first mobile phone’s menu, activate its Bluetooth connection with the
headset.

Using Your Headset

Function Button Audio Status Indicator

Power ON Press and hold the MFB for 2 a short beep Flashing blue light 3
seconds times

When you turn on your headset for the first time, the headset automatically enters the
pairing mode, i.e. the status indicator flashes blue and red alternately. This allows you
to immediately pair your headset and mobile phone.

Power OFF Press and hold the MFB for 2 a long beep
seconds

Red light for two seconds
and then the light goes off

Using Your Headset (cont'd)

Function Button Audio Status Indicator

Answer a call Press the MFB once Flashing blue light

End a call Press the MFB once Flashing blue light

Adjust Volume Press the Volume Key once to a short beep Flashing blue light
increase / decrease by 1 step
(Total 6 levels)

Voice Dialing Press the MFB once a short beep Flashing blue light

Say the voice tag as soon as you hear the short beep and you must have recorded the voice
tag into your mobile phone.

Last No. Redial Double click the MFB Flashing blue light
Call Reject Press and hold the Volume Key a short beep Flashing blue light
for 2 seconds

Call Transfer While speaking, press and hold Flashing blue light
(headset to mobile phone) the Volume Key for 2 seconds

Call Transfer While speaking, press MFB once Flashing blue light
(mobile phone to headset)

6 7