Page 1
User Manual
Version 1.0
Full IP67 Aluminum
WRD Rugged PC Series
i-Tech Company LLC
TOLL FREE: (888) 483-2418 • EMAIL: info@itechlcd.com • WEB: www.iTechLCD.com
Page 2
19” Full IP67 Rugged PC User’s Manual
1
Safety Information
WARNING!
Always completely disconnect the power cord from your chassis whenever you work
with the hardware. Do not make connections while the power is on. Sensitive
electronic components can be damaged by sudden power surges. Only experienced
electronics personnel should open the PC chassis.
CAUTION!
Always ground yourself to remove any static charge before touching the CPU card.
Modern electronic devices are very sensitive to static electric charges. As a safety
precaution, use a grounding wrist strap at all times. Place all electronic components in a
static-dissipative surface or static-shielded bag when they are not in the chassis.
Safety Precautions
•
Please read these safety instructions carefully.
•
Please keep this user’s manual for later reference.
•
Please disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray
detergents for cleaning. Use a damp cloth.
•
Do not touch the LCD panel surface with sharp or hard objects.
•
For pluggable equipment, the power outlet must be installed near the equipment and
must be easily accessible.
•
Keep this equipment away from humidity.
•
Place this equipment on a reliable surface during installation. Dropping it or letting it fall could
cause damage.
•
The openings on the enclosure are for air convection. Protect the equipment from overheating. DO NOT
COVER THE OPENINGS.
•
Make sure the voltage of the power source is correct before connecting the equipment to the power
outlet.
•
Position the power cord so that people cannot step on it. Do not place anything over the
power cord.
•
All cautions and warnings on the equipment should be noted.
•
If the equipment is not used for a long time, disconnect it from the power source to avoid
damage by transient over-voltage.
•
Never pour any liquid into an opening. This could cause fire or electrical shock.
•
Never open the equipment. For safety reasons, only qualified service personnel should open the
equipment.
Page 3
19” Full IP67 Rugged PC User’s Manual
2
•
If any of the following situations arises, get the equipment checked by service personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to the
user’s manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
•
Do not leave this equipment in an uncontrolled environment where the storage temperature is below
-10°C (14°F) or above 60°C (140°F). It may damage the equipment.
• CAUTION – Use recommended mounting apparatus to avoid risk of injury.
• WARNING – Only use the connection cords which comes along with the
product, when in
doubt, please contact the manufacturer.
•
Provision shall be made to provide transient protection device to be set at a level not exceeding 140%
of the rated voltage at the power supply terminals of the apparatus.
• WARNING – The equipment should be adequately protected from direct light
when installed indoor
or outdoor.
Page 4
19” Full IP67 Rugged PC User’s Manual
3
Contents
Contents ........................................................................................................................ 3
Introduction .................................................................................................................. 4
Features ............................................................................................................................................... 4
Package Contents ................................................................................................................................. 5
Product Overview................................................................................................................................. 6
Getting Started .............................................................................................................. 7
Turning On Your Device ....................................................................................................................... 7
Adjusting the LCD Display Brightness ................................................................................................... 8
Calibrating Touch Screen ......................................................................................................................9
Turning Off Your Device ..................................................................................................................... 11
Installation .................................................................................................................. 12
Wiring Requirements ......................................................................................................................... 12
Connecting the Interface ................................................................................................................... 13
Mounting Solution ............................................................................................................................. 15
Specification ................................................................................................................ 19
Hardware Specifications .................................................................................................................... 19
Appendix ..................................................................................................................... 21
Appendix A: Cleaning the Monitor ..................................................................................................... 21
Appendix B: Statement of Regulatory Approval ................................................................................ 23
Page 5
19” Full IP67 Rugged PC User’s Manual
4
Introduction
i-Tech's WRD Series consists of rugged and unusually well-sealed vehicle or stationary-mount Panel PCs
available in a wide variety of configurations. Depending on the intended application, WRD panels have
been available with 5-wire resistive touch displays measuring 8.4, 10.4, 12.1 or 15-inches diagonally.
Since the sealed nature and high reliability requirements of the WRD line precluded fans and cooling
slots, WRD Panel PCs were designed with low power processors that didn't generate a lot of heat. That
meant either Intel Cedar Trail or, more recently, Intel Bay Trail processors. While even Bay Trail is still
based on the Intel Atom processor architecture, higher end quad-core Bay Trail chips such as the quad-
core N2930 used in several WRD models have grown quite powerful. Sometimes, however, an even
larger display is needed, and even higher performance, and that's where the new 19-inch WRD panels
come in.
This new 19-inch WRD panel does not only offer considerably more screen real estate than a 15-inch
model — about 90% more in fact — but the larger case also provides enough extra heat dissipation to
allow the use of Intel Haswell Core processors with their higher thermal design power and significantly
higher performance.
Features
• Intel Haswell Core i5-4300U turbo max 2.6 GHz
• 19” SXGA High brightness panel, 400 nits
• Sunlight readable, transflective, resistive touch LCD Panel
• Fanless, streamlined enclosure for highly efficient heat dissipation
• Front side buttons, one dedicated button to enable/disable touch screen interface
• Built in to withstand extreme temperatures (-10 deg C to 60 deg C)
• 9-36 V DC input (with isolation)
• Operable in 5-95% humidity level
Page 6
19” Full IP67 Rugged PC User’s Manual
5
Package Contents
Before using this Panel PC, please make sure that all the items listed below are present in your package:
Panel PC AC to DC adapter Power cord USB cable
USB adapter
(USB Type A to Type B)
Ethernet cable Ethernet extension
adapter
RS-232 cable
Recovery DVD Touch driver CD VESA mounting
screws
VGA cable
User’s manual
Quick start guide
Page 7
19” Full IP67 Rugged PC User’s Manual
6
Product Overview
Front View
Side and Rear Views
Front Button
Button Type
Function
Power on/off
Increase the brightness of the Panel
Decrease the brightness of the Panel
Suspend the touch’s function temporarily
Programmable function key configured by Hot Tab Utility
Front Button &
LED Indicators
Touch Display
Page 8
19” Full IP67 Rugged PC User’s Manual
7
Getting Started
Turning On Your Device
1. Remove the protective cap of the DC IN jack.
2. Connect the AC adapter to the power cord.
3. Plug the power cord to an electrical outlet.
4. Touch the Power button on the front to turn on the device.
Note
•
When the system hangs, press the Reset button to restart the device.
Page 9
19” Full IP67 Rugged PC User’s Manual
8
Adjusting the LCD Display Brightness
1. Tap the arrow on the system tray to display the
hidden
icons.
2. Double-tap the icon to display the brightness
menu.
3. Drag the brightness bar to adjust the brightness level according to your preference.
Page 10
19” Full IP67 Rugged PC User’s Manual
9
Calibrating Touch Screen
When turning on the Panel PC for the first time, it is highly recommended to calibrate the touch screen to
ensure touch accuracy.
Five-wire resistive touchscreens
The five-wire resistive touchscreens use a glass panel with a uniform resistive coating. A thick polyester
coversheet is tightly suspended over the top of the glass, separated by small, transparent insulating dots.
The coversheet has a hard, durable coating on the outer side and a conductive coating on the inner side.
A
B
C
D
E
F
When the screen is touched, the conductive coating makes electrical contact with the coating on the
glass. The voltages produced are the analog representation of the position touched. The controller
digitizes these voltages and transmits them to the computer for processing. The five-wire
technology utilizes the bottom substrate for both X and Y-axis measurements. The flexible
coversheet acts only as a voltage-measuring probe. This means the touchscreen will continue
working properly even with non-uniformity in the cover sheet’s conductive coating. The result is an
accurate, durable and reliable touchscreen that offers drift free operation. The touchscreens are
sealed against contamination and moisture. The coversheet is sealed to the glass substrate with an
industrial grade caulk. This prevents wicking of fluid between the coversheet and glass. Also, the
touchscreens are not air vented, thereby preventing fluid ingress through an air vent.
Brief Specifications
Subject
Details
Input Method
Finger, gloved hand, or stylus activation
Positional Accuracy
Standard deviation error is less than 0.080 (2 mm)
Resolution
Touch point density is based on controller resolution of 4096 x 4096
Touch Activation Force
Typically less than 4 ounces (113 grams)
Light Transmission
HL products: 80% +/–5% at 550 nm wavelength Enhanced products: 60%
+/–5% at 550 nm wavelength
Update touch-screen driver or new information. Go to www.elotouch.com.
A
B C D
E F
Page 11
Page 12
19” Full IP67 Rugged PC User’s Manual
10
Elo Touch Correction
i-Tech ELO Touch driver software provides a consistent software interface among all ELO touch
screens and controllers.
Go to http://www.elotouch.com/Support/dnld.asp for a complete list of available supports.
After the driver installation is complete, do the following to perform touch screen calibration.
1. Tap the arrow on the system tray to display the hidden icons.
2. Double-tap the icon to display the Elo Touchscreen menu.
3. Double-tap the icon to proceed to next step.
Page 13
19” Full IP67 Rugged PC User’s Manual
11
4. Follow the on-screen instructions to calibrate the touch screen.
5. Tap the icon if the cursor follows your finger to finish and exit the calibration utility.
Page 14
19” Full IP67 Rugged PC User’s Manual
12
Turning Off Your Device
To shut down your device, do the following: Tap Start ( ) > Shut down.
Wait for your Panel PC to completely turn off before disconnecting the power cord (if necessary).
Page 15
19” Full IP67 Rugged PC User’s Manual
13
Installation
Wiring Requirements
The following common safety precautions should be observed before installing any electronic device:
•
Strive to use separate, non-intersecting paths to route power and networking wires. If power
wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection
point.
•
Keep the wires separated according to interface. The rule of thumb is that wiring that shares
similar electrical characteristics may be bundled together.
•
Do not bundle input wiring with output wiring. Keep them separate.
•
When necessary, it is strongly advised that you label wiring to all devices in the system.
ATTENTION
•
Do not run signal or communication wiring and power wiring in the same conduit. To avoid
interference, wires with different signal characteristics (i.e., different interfaces) should be routed
separately.
•
Be sure to disconnect the power cord before installing and/or wiring your device.
•
Verify the maximum possible current for each wire gauge, especially for the power cords.
Observe all electrical codes dictating the maximum current allowable for each wire gauge.
•
If the current goes above the maximum ratings (80 W), the wiring could overheat, causing
serious damage to your equipment.
•
Be careful when handling the unit. When the unit is plugged in, the internal components generate a
lot of heat which may leave the outer casing too hot to touch.
Page 16
19” Full IP67 Rugged PC User’s Manual
14
Connecting the Interface
The unit is available with different pass through IP67 connector for cable connections (required to
maintain enclosure protection rating). These IP67 connectors are water and gas tight and must be
tightened with a torque described in the gland manufacturer’s instructions provided with the unit. Cables
must be passed through the connector and wired to the associated I/O connectors.
Pin Assignments
The pin assignments of the connectors are as follows:
VGA Port
Pin
Signal Name
Pin
Signal Name
1
R_FILTER
2
G_FILTER
3
B_FILTER
4
NC
5
GND
6
GND
7
GND
8
GND
9
VGA5V
10
GND
11
NC
12
DAC_SDAT0
13
3VHSYNC0
14
3VVSYNC0
15
DAC_SCL0
Page 17
19” Full IP67 Rugged PC User’s Manual
15
COM Port
USB Port
LAN1 Port
Power terminal block
COM Port
Pin
Signal Name
Pin
Signal Name
1
DCD 2 RXD
3
TXD 4 DTR
5
GND
6
DSR 7 RTS 8 CTS
9
RI
Pin
Signal Name
1
VCC 2 D- 3 D+ 4 GND
Pin
Signal Name
Pin
Signal Name
1
MDI0_IN+
2
MDI0_IN-
3
MDI1_IN+
4
MDI2_IN+
5
MDI2_IN-
6
MDI1_IN-
7
MDI3_IN+
8
MDI3_IN-
Pin
Signal Name
1
VCC
2
GND
3
NC
Pin
Signal Name
Pin
Signal Name
1
DCD 2 RXD
3
TXD 4 DTR
5
GND 6 DSR 7 RTS 8 CTS
9
RI
10
+V5
Page 18
19” Full IP67 Rugged PC User’s Manual
16
LAN2 Port
USB Port
Note
•
This adapter was certified by UL, CUL TUV/GS CE, FCC, BSMI, EK, DOIR+C- TICK, CCC,
PSE.
WARNING
Ensure that the external power source is OFF before connecting or disconnecting
the DC IN jack.
Mounting Solution
VESA Mount
• Dimensions: 100 x 100mm
• Screw Hole Diameter: M4 x 5 mm
• Direction:
Compatible with swimming arms mounting kits.
Pin
Signal Name
Pin
Signal Name
1
MDIO3-
2
MDIO3+
3
MDIO2-
4
MDIO2+
5
MDIO1-
6
MDIO1+
7
MDIO0-
8
MDIO0+
Pin
Signal Name
1
VCC
2
D-
3
D+
4
GND
Page 19
19” Full IP67 Rugged PC User’s Manual
17
Rear Mount
Before you start installing the rear mount, be sure that you have the following components:
19” Stainless Steel LCD
2 x Bracket
M4, 4mm Screws
To install the rear mount, perform the following:
1. Prepare a customized fixture for 19” panel pc/display.
Match the active display
area of your rear mount
display
9
4
6
Page 20
19” Full IP67 Rugged PC User’s Manual
18
2. Screw the brackets on both sides of your device.
3. Secure the display from the back side first, so the outer frame can be fully covered to ensure the safety
of your display.
Page 21
19” Full IP67 Rugged PC User’s Manual
19
4. Make sure your screws are tight and on the right position.
Page 22
19” Full IP67 Rugged PC User’s Manual
20
Specification
Hardware Specifications
Item
Specifications
Computer
CPU
Intel i5-4300u turbo Max 2.9GHz
OS
Windows 7 embedded systems
System Chipset
Intel® HD graphics 5000
Bios
AMI 16Mbit Flash
System Memory
8GB capacity, 4GB pre-installed
USB
3 x USB 3.0
Storage
Storage Support
Removable 128GB industrial grade SSD to store OS;
support up to 256GB
Display
Panel Size
19-inch 1280 x 1024, 800nit LED backlight LCD
Contrast Ratio
1000:1
Response Time
10ms
View Angles
•
Horizontal: 170 degree (left to right)
•
Vertical: 160 degree (up to down)
Max Colors
16.7M colors
Touch
Flat Resistive single point touch, suitable for use outdoors
around heavy equipment
Ethernet Interface
Hardware Interface
1 x RJ45; 1 x 8pins terminal block
Serial Interface
Serial Standard
1x DB9 RS232; 1 x 10pins terminal block
Power Requirements
Input Voltage
Typical 9~36V DC (isolation 1.5V)
Page 23
19” Full IP67 Rugged PC User’s Manual
21
Item
Specifications
Physical Characteristics
Housing
Stainless steel
Dimensions
396 x 310 x 49mm (W x H x D)
Mounting
Mounting hole for VESA 100 x 100, yoke mounting
Environment Limits
Operating Temperature
-40°C to 60°C
Storage Temperature
-40°C to 80°C
Ambient Relative Humidity
5 to 95% (non-condensing)
Page 24
19” Full IP67 Rugged PC User’s Manual
22
Appendix
Appendix A: Cleaning the Monitor
Before cleaning:
•
Make sure the device is turned off.
•
Disconnect the power cable from any AC outlet.
When cleaning:
•
Never spray or pour any liquid directly on the screen or case.
•
Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
•
The display area is highly prone to scratching. Do not use ketene type material (ex. Acetone), Ethyl
alcohol, toluene, ethyl acid or Methyl chloride to clear the panel. It may permanently damage the
panel and void the warranty.
•
If it is still not clean enough, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto
a clean, soft, lint-free cloth, and wipe the screen.
•
Do not use water or oil directly on the display screen. If droplets are allowed to drop on the screen,
permanent staining or discoloration may occur.
Page 25
19” Full IP67 Rugged PC User’s Manual
23
Appendix B: Statement of Regulatory Approval
Refer the following descriptions for various approvals and certifications
Low Voltage Directive European Safety for Industrial Control Equipment
Self-Declaration in accordance with European LVD Directive 2006/95/EC; Independent
3rd party assessment (Accredited by IEC 17025)
Electromagnetic Compatibility Directive European EMC for Industrial
Control Equipment
Self-Declaration in accordance with EMC Directive 2004/108/EC; Independent 3
rd
party assessment (Accredited by IEC 17025)
Loading...