I-Tech iAP-2000, iNAP-2000, iOP-2000 User Manual

Dedicated LCD display solutions

User Manual

20"

LCD

iAP-2000

Aluminum front bezel

iNAP-2000

Front NEMA4/IP65

iOP-2000

Universal Mounting Open Frame

^

^

|-T~E^j|"~I

C^DN^RA^TY

i-Tech

F^ (^ REACH

J

Company LLC

TOLL FREE: [phone] • EMAIL: [e-mail] • WEB: www.iTechLCD.com

Legal Information

First English printing, October 2002
Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness
of the contents. The information in this document is subject to change without notice. We are not liable for any injury or
loss that results from the use of this equipment.

Safety Instructions
Please read all of these instructions carefully before you use the device. Save this manual for
future reference.

■ Unplug equipment before cleaning. Don't use liquid or spray detergent; use a moist cloth.

■ Keep equipment away from excessive humidity and heat. Preferably, keep it in an air-conditioned environment with
temperatures not exceeding 40° Celsius (104° Fahrenheit),

■ When installing, place the equipment on a sturdy, level surface to prevent it from accidentally falling and causing
damage to other equipment or injury to persons nearby.

■ When the equipment is in an open position, do not cover, block or in any way obstruct the gap between it and the
power supply Proper air convection is necessary to keep it from overheating.

■ Arrange the equipment's power cord in such a way that others won't trip or fall over it.

■ If you are using a power cord that didn't ship with the equipment, ensure that it is rated for the voltage and current
labeled on the equipment's electrical ratings label. The voltage rating on the cord should be higher than the one listed
on the equipment's ratings label.

■ Observe all precautions and warnings attached to the equipment.

■ If you don't intend on using the equipment for a long time, disconnect it from the power outlet to prevent being
damaged by transient over-voltage.

■ Keep all liquids away from the equipment to minimize the risk of accidental spillage. Liquid spilled on to the power
supply or on other hardware may cause damage, fire or electrical shock.

■ Only qualified service personnel shojld open the chassis. Opening it yourself could damage the equipment and
invalidate its warranty.

■ If any part of the equipment becomes damaged or stops functioning, have it checked by qualified service personnel.

What the warranty does not cover

■ Any product, on which the serial number has been defaced, modified or removed.

■ Damage, deterioration or malfunction resulting from:
□ Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or

failure to follow instructions supplied with the product.
D Repair or attempted repair by anyone not authorized by us.
D Any damage of the product due to shipment.
□ Removal or installation of the product.
□ Causes external to the product, such as electric power fluctuation or failure.
D Use of supplies or parts not meeting our specifications.
D Normal wear and tear.
D Any other causes which does not relate to a product defect.

■ Removal, installation, and set-up service charges.

Regulatory Notices Federal Communications Commission (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
Any changes or modifications made to this equipment may void the user's authority to operate this equipment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures;

■ Re-position or relocate the receiving antenna

■ Increase the separation between the equipment and receiver.

■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Contents

Part. 1 > iAP-2000 / iNAP-2000

1.1 Package Content P.1

1.2 Structure Diagram & Dimension P.2

1.3 Mounting Hardware & Installation P.4

Part. 2 > iOP-2000

2.1 Package Content P.6

2.2 Structure Diagram & Dimension P.7

2.3 Mounting Hardware & Installation P.9

Part. 3 > Specifications / OSD

3.1 Product Specifications

3.2 On-screen Display Operation (OSD )

Part. 4 > Options

4.1 Option Table

4.2 3G / HD / SD-SDI Broadcast-grade input P.14

4.3 MCS Multi-display control solution

4.4 AV2.2D Upgrade : DVI-D, S-Video + BNC & Audio P.16

AV2.2H Upgrade :

4.5 AV3.0 Upgrade :

4.6 Resistive ( single point touch )

4.7 48V, 24V or 12VDC power P.21

4.8 MIL-type or lockable connector P.22

P.

P.

P.

P.

HDMI,
HDMI,

S-Video + BNC & Audio

DVI-D, S-Video + BNC & Audio P.18

P.

10

12

13

15

19

4.9 Quad display for CCTV P.23

4.10 TV (Analog) P.24

Before Installation

■ It is very important to mount the equipment in a suitable cabinet or on a stable surface.

■ Make sure the place has a good ventilation, is out of direct sunlight, away from sources of excessive
dust, dirt, heat, water, moisture and vibration.

Unpacking

The equipment comes with the standard parts shown in package content. Check and make sure they are
included and in good condition. If anything is missing, or damaged, contact the supplier immediately.

How To Clean Your LCD Monitor
4k Caution :

■ To avoid the risk of electric shock, make sure your hands are dry before unplugging your monitor from or
plugging your monitor into an electrical outlet.

■ When you clean your monitor, do not press down on the LCD screen. Pressing down on the screen can
scratch or damage your display. Pressure damage is not covered under warranty.

■ Use only cleansers made specifically for cleaning monitors and monitor screens. Cleansers not made to
clean monitors and monitor screens can scratch the LCD display or strip off the finish.

■ Do not spray any kind of liquid directly onto the screen or case of your monitor. Spraying liquids directly
onto the screen or case can cause damage which is not covered under warranty.

■ Do not use paper towels or abrasive pads to clean your monitor. Using an abrasive pad or any wood based
paper product such as paper towels can scratch your LCD screen.

Cleaning Your Monitor

To clean your LCD safely, please follow these steps :
© Disconnect the power
@ Gently wipe the surface using a clean, dry microfiber cloth. Use as little pressure as possible.

cord.

Cleaning Tough Marks and Smudges

To remove tough marks and smudges, please follow these steps
© Disconnect the power
© Spray a small amount of non-abrasive cleanser on a microfiber cloth.

cord.

A Caution : Do not spray or apply any liquids directly onto the monitor. Always apply the solution to your

** microfiber cloth first, not directly on the parts you are cleaning.
® Gently wipe the surface. Use as little pressure as possible.

@ Wait until your monitor is completely dry before plugging it in and powering it up.

< Part 1 >
< 1.1 > Package Content - iAP / iNAP-2000

iAP-2000 / iNAP-2000

20"

LCD display X1
6ft VGA cable X 1
Power adapter X 1
Power cord X 1

Mounting hardware X 1 pack

- Mounting bracket x 4 pcs

- M4* 6mm screw x 8 pcs

- M4* 50mm screw x 8 pcs

Basic I/O

Power

Power

0

0

AV2.2D upgrade I/O

Audl

Power BNC S-Video

0 © © O O O

0 © © O O O

AV2.2H upgrade I/O

Power BNC S-Video

0 ®'"

AV3.0 upgrade I/O with advanced features

Power

BNC S-Video

BNC S-Video

Power

BNC S-Video

0

0

0

- An abundance of input connections that include

- On-chip Faroudja® DCDi Cinema processing

- Casing dimensions will be changed

Audl

out -

in

out -

in

Video PC

Video PC

Audl

O O O HDMI

out -

in -

Video PC

Audio

Audio

Audio

O

O

out

out

out

O

- in -

- in -

- in -
Video

Video

Video

0 o

0 o

0 o

°

°

- in

- in

°

in

o

o

o

in

in

in
PC

PC

PC

HDMI

HDMI

HDMI

DVI-0 VGA

FCHFi ■; -:.-,.-.;

DVi-D VGA Power BNC S-Video

l-rim-l

tf■■:■/■:)>

VGA

DVI-D VGA Power

i"i Bid

i"i Bid

cfsr m

>

HDMI,

DVI-D, VGA, S-Video + BNC and audio

P.1

<

1.2 >

Structure Diagram

- iAP /

iNAP-2000

iNAP-2000

Front view

iAP-2000

20"

LCD

Display

(?) Rear case
©

LCD
© Protective 3mm glass
(4) 6mm aluminum front bazel
(5) Audio speaker
(D
(7) Remote sensor

Model

LCD

panel

membrane

(for

HDMI.

• ©

o v « » * f>

Product Dimension

(W

x D x H)

Audio

or TV

option

——:—i;

.

p

p

°

•

-—r

Packing Dimension

(W

x D x H)

■*■ ■" I

—r^rr

1: :i _ . _ .

CD

Rear view

;i—^^

•

• *

•

• *

■

Net

Weight

•-©

■J

A
W

•

Gross

Weight

IAP-2000

INAP-2000

512.5x72.1

20.2x2.8x15.4 inch

x 391.6 mm

651

x 124

x597

mm

25.6x4.9x23.5 inch

P. 2

6

13.2

kg

lbs

8

17.6

kg

lbs

< 1.2 > Dimension - iAP / iNAP-2000

Front View Side View

T-Q

50.8

50.8

Rear View

iAP-2000

iNAP-2000

rxi

411

518.5

488.6

3 s °°°—-

OS

o

co

<*

o>

o>

CO

CO

I

— ]

»7.6

J661

_Z£L

1mm ■

UNIT: mm

0.03937

inch

CO

Bottom View

Czr

40.8I

-» ii i I v ^s- iS

199.3 80

C3

g o o o

396.9

47&5

p

478.5

o ® ©

CO

~t

3

s

< 1.3 > Panel Mount Installation - iAP / iNAP-2000

20"

LCD Display

Mounting
bracket

x4 pcs

l£

Hardware set part no. UV-BK#2

Q M4*6mm

screw

x8 pcs

(\ M4*50mm screw

x8 pcs

01

-,

0

'■■■*

p-

r

Steps

■ Install 4 mounting brackets with 8 x M4*6mm screws

■ Adjust the LCD panel with 8 x M4*50mm screws and fix it on the surface.

P.4

< 1.3 > VESA mount Installation - iAP / iNAP-2000

\

M4 screw

100

VESA mount (100*100mm )

I Hardware and M4M pcs for VESA mount are not provided

P.5