I-Tech ADTR-IP66 Series Quick Reference

SxxxxADTR-IP66 Series
Quick Reference
i-Tech Company LLC TOLL FREE: (888) 483-2418 • EMAIL: info@iTechLCD.com • WEB: www.iTechLCD.com
1. Feature
Highlights:
Whole Unit IP66 Certification
Aluminum Casing
Fanless design
Removable Hard Disk
Wireless LAN
VESA Mount or Stand
Sub-Nano Coating
Applications:
Hospitality
Retail
Finance & Banking
Travel & Transportation
Self-service Kiosk
Note: Optional devices such as VESA standard mounting bracket or arm, Rotation disk, Customer Display, Magnetic Card Reader, Smart Card Reader, I-Button, Finger Print, RFID, and other I/O devices are available for optional choice.
1
2. Unpacking
The following items are included when you purchase the SxxxxADTR­IP6. If any items are damaged or missing, please contact your dealer for assistance.
Quick Reference
Antenna
(Optional Part)
3. Configuration
Front and Rear View
Push ON Switch-
Foot(5x)
XT USB
2
VFD Interface Cover
Antenna X^HDD Cover
Bottom View – I/O Connector Location
Chassis Inner View
3
I/O Connector Location (VESA MOUNT)
COM6 COM5 COM4 COM3 Audio Out
CF Card
4. Power On
Red Blue
- AC Input OK
- Power On Mode
4
PRINTER or VGA
EXT USB
PS2 K/B
LAN
EXT USB
Turn on the unit by pressing “Push ON Switch” located under iTech logo indicator at front of the LCD. Turn off the unit manually by pressing and holding the switch for 3 seconds. When connected to an AC power, the Power Mode LED will illuminate automatically. The unit’s mode can be determined by the Power On Mode LED color. Indicator modes as follows:
5. HDD Replacement
To remove HDD, use a screwdriver to loosen the screws on left side of the panel.
Caution :
A. Hard Disk must be screwed into HDD Cover. B. To install or to withdraw HDD, power must be switched off.
5
6. LCD Angle Adjust
6.1 In order to accommodate various operating preferences and lighting conditions. SxxxxADTR-IP66 is equipped with a manual tilt adjustment mechanism. The Adjustment button is located underneath the display.
6.2 To adjust the tilt angle, press adjustment button as indicated
direction. The tilt angle is limited to a minimum of 34 degree and a maximum to 70 degrees.
6.3 After tilt angle has been adjusted, release the button. When
adjustment button released, LCD angle is locked.
6
7. VESA Mounting
SxxxxADTR-IP66 is designed to be fitted with a desk stand base unit or with a VESA standard mounting bracket or arm (75mmX75mm or 100mm X 100 mm) if required.
Note : The length of M4 screws mu st not exceed 8mm
7.1 Unscrew the two M4x8L thumbscrews that secured the base unit to SxxxxADTR-IP66.
7.2 Separate SxxxxADTR-IP66 from the base unit by lifting the LCD
panel.
7
7.3 Place AC Power Adapter into the Power Adapter Cover. Place silica gel grommet onto cable and fit into it’s matching position on the Power Adapter Cover. The empty holes in silica gel grommets where cables are not installed are fitted with Silica gel plug to provide water resistance. Then, use Velcro to fasten AC Power Adapter.
7.4 With each I/O cable in position, tighten the cable fixing panel by two M3 x 15L screws. Then, secure the AC Power Adapter Cover to the SxxxxADTR-IP66 back cover by eight M3 x 6L screws.
8
7.5 Use four M4x8L screws to secure SxxxxADTR-IP66 onto any VESA standard mounting bracket or arm.
M ounting on the ceiling
The cable assembling sequence as follows.
1. DC IN cable x 1
2. SCSI Printer cable x 1
3. RS232 x 4
4. LAN x 1
5. PS2/KB x 1
6. USB cable x 2
7. Audio cable x 1
8. Microphone cable x 1
9
8. Rotation Disk Installation
SxxxxADTR-IP66 is designed to be fitted with a 135° rotation disk to enhance flexibility.
8.1 Use a screwdriver to remove the screws from five rubber feet.
8.2 Put I/O Cable through the rotation disk, then slide the rotation disk into lock position. (Note: The table must have a 65mm hole)
8.3 Cable management is best achieved when the SxxxxADTR-IP66 is positioned above a hole on the table (65mm in diameter). Cables will fall directly beneath the bench providing extra space. If the table does not have a hole for the cables to run through, rubber feet (5) will need to be replaced so that there is enough space between the table and the unit for cables to run through.
10
9. Additional Devices : Driver Installation
After installing Win98 SE / ME / 2000 / XP / VISTA / Window 7, SxxxxADTR-IP66 will need additional devices drivers installed which are located in Driver CD. (Note : S150ADTR-IP66 supports Windows XP)
Driver CD menu
S150ADTR-
IP66
AMD GeodeLX Windows XP AES Driver
AMD PCI IDE Controller Driver
How to Install PCI IDE Controller Driver
AMD GeodeLX Windows XP Display Driver
AMD GeodeLX Windows XP Audio Driver
Driver Install Description
Dignostic
MB Linux Driver
S650ADTR-
IP66
Intel(R) Chipset Software Installation Utility
Intel(R) 945 GM/GSE Graphics Driver
Realtek High Definition Audio Driver
Realtek GbE PCI-E NIC Driver
PCI-E wireless LAN Driver
Observer 5.0.13(iSPOS650)
LAN Card
Realtek Network Interface Controller Drivers
Wireless LAN Driver
Document
iSPOS Series Document
KDS Series Document
iSMON Series Document
Tools
IC Card Reader
Touchscreen Driver
iTechLCD OPOS Driver
Testing Video
IP66 Testing Video
9.1 Install the touch driver from enclosed driver CD. COM Port for Touch Controller is located on COM 2.
9.2 IC Card Reader (The driver should be installed only if required by the application).
9.3 iTechLCD OPOS Driver (The driver should be installed only if required by the application).
11
Precaution
® Specifications are subject to change without notice. ® Avoid exposing the product to direct sunlight and do not use the product near
areas of high moisture.
® Do not block the unit’s ventilation openings. ® Do not attempt to disassemble or modify this product by yourself, as doing so
may expose you to an electric shock. All servicing should be performed by qualified personnel and should conform to all local codes ® SxxxxADTR-IP66 is equipped with the specific adapter (12V 5A). Do not use any other type of adapter to operate the product. It is recommended that you only use the manufacturer’s supplied adapter. ® If any abnormal power conditions or blackouts occur during operation, disconnect unit at the AC source immediately. Once normal power is restored, reconnect the AC source. ® To avoid unit failure or intermittent operation, check power and other I/O cables are connected correctly. ® Always unplug the power cord from the AC outlet before cleaning the product. Use a soft cloth to clean the product. Do not use solvents or abrasives and do not spray or pour any liquid directly onto the product’s screen or case.
12
i-Tech Company LLC TOLL FREE: (888) 483-2418 • EMAIL: info@iTechLCD.com
• WEB: www.iTechLCD.com
Loading...