ITEAD Intelligent Systems SONOFF User Manual

Overview
onoff TH10/16 is a Sonoff version that can monitor and set temperature and humidity through the APP eWeLink. Just as the name indicats, the new version Sonoff TH device supports two power supply specifications: 10A or 16A. Sonoff TH 10/16 supports presetting range for temperature or humidity, when the temperature or humidity of the environment falls into the range, it will automatically turn on or turn off connected devices.
We are selling two kinds of sensors: AM2301 and DS18B20. We've customize an interface for Sonoff TH10/TH16 to easily connect with the sensor, just plug and play. Note that the sensor should be plug into Sonoff TH before you power it up, don't plug or unplug the sensor in power on status. AM2301 is non-waterproff, while DS18B20 can work in water.
Features
Supports 90 ~ 250V AC input
Support max 10A /16A input
Support fast configure SSID and password connection through APP
Support automatic connect to server, register and update status info.
Support tracking device status and timely remote control through APP
Support setting single/repeat/countdown timing tasks
Support real-time temperature and humidity displaying
Support 3 temperature and humidity sensors (AM2301, DS18B20, DHT11)
Support preset temperature and humidity range to turn on/off
WIFI Characteristics
802.11 b/g/n
• Built-in Tensilica L106 ultra-low power consumption 32-bit micro-MCU, dominant
frequency support 80 MHz and 160 MHz, support RTOS
• Built-in TCP/IP protocol stack
• Built-in TR switch, balun, LNA, power amplifier and matching network
• Built-in PLL, voltage regulator and power supply management components, 802.11b
mode +20 dBm output power
• A-MPDU&A-MSDU aggregation and 0.4μs guard interval
• WiFi @ 2.4 GHz, supports WPA / WPA2 safe mode
• Support cloud OTA upgrade
• Support STA/AP/STA + AP mode
• Standby power consumption is less than 1.0 mW (DTIM3)
• Other parameters are as follows
Category Parameters Description
Wireless Parameter
Hardware Parameter
Wireless standard 802.11 b/g/n
Frequency range 2.4GHz-2.5GHz (2400M-2483.5M)
UART/I2C
Data port
GPIO/PWM
Operating voltage 3.0~3.6V(recommend 3.3V)
Operating current Average: 80mA
Operating temperature
Operating Humidity
0ºC-40ºC(32°F-104°F)
5%-90%RH, Non-condensing
Software Parameter
PCBA size 89.1mm*45.0mm*1.2mm
Wireless network mode
station/softAP/SoftAP+station
Security mechanism
Encryption type WEP/TKIP/AES
WPA/WPA2
Firmware upgration
Software development
Network protocols IPv4, TCP/UDP/HTTP/FTP
User configuration
Local serial programming/Cloud Upgrade/Host download programming
Support secondary development
cloud server, Android/iOS APP
Specification
PCB_Size 89.1X45.0X1.2mm
Interface DHT11/DS18B20/AM2301
Indicator LED WiFi, on or off state
Electrical Characteristics
Hardware
Warning Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Loading...