ITC TS-0690 User Manual

Intelligently digital conference

system

User Manual

TS-0690

Before using the system, please read this manual first

NOTE:

This manual only as an instructions for user, not for service purposes. From the

date of issue, if the function or technical parameters change later, another supply

mentary instruction will be added, the details can be inquired to the manufacturers.

This manual is a product manufacturer Copyright, unauthorized and any entity

or individual shall not take part or all the contents as commercial purposes.

This manual used for intelligent digital conference system.

!

SAFETY OPERATIONAL GUIDANCE

In order to make sure the correct operation and safety using, please comply with

the following conditions when installation, operating and maintenance.

1) Make sure the connection of the ground wire is well enough when installation.

Do not use two-core plug. And make sure the input voltage of power supply is

as same as the one marked on the main controller.

2) Do not open the cover of the unit without permission especially the

high-voltage components marked with AC 100V to 240V, or there is risk of

shock.

3) Do not put the unit in extremely cold or hot place.

4) The unit will be heating when working. Please keep environment ventilation to

avoid overheating.

5) Please power off the unit in wet weather or not in use.

6) Please disconnect the AC power wiring from the AC power supply before the

below operations:

A. Remove or re-assembly any parts of the unit.

B. Disconnect or re-connect any plug of the unit or other connection

1 Non professionals without permission, please do not attempt to open the

enclosure,do not repair, in order to avoid the accident or exacerbation of

equipment damage degree.

8) Don't take any corrosive chemical powders or liquids spilled in the equipment or

in the vicinity of.

1

1. Introduction of Digital Conference System

About ITC Digital Conference System

◆ Digital conference system is another high-tech professional product after

multimedia central control products and audio-video matrix products. It

includes discussion units, simultaneous interpretation system, IR voice

distribution, remote telephone conference, voting and camera tracking etc.

◆ Based on our complete system solution idea, it could be closely compatible

with both DCS (Digital conference System) and MCS (Multimedia Central

System) to become a complete intelligent conference system solution.

◆ This user manual is applicable to Intelligent Digital Conference Controller,

Discussion Units, Camera Tracking System and Telephone Conference System.

2

2. Features

◆ Supporting 6 video signals inputs: RCA, BNC, VGA, 3 lines of video signal

inputs.

◆ Built-in Scaler, transferring VIDEO signal to VGA output, capable of being set

as 800x600，1024x768，1280x1024 DPI in the software.

◆ Supporting TS and TH series conference controller at the same time and

compatible with three kinds of camera tracking controllers: TH-0580,

TH-9000M and TS-0690.

◆ The tracking controller has a function of screen freeze, and the period of

screen freeze could be set by the software.

◆ The ID number and preset position of the camera could be set by PC. Each

camera could be preset about 127+1 and with 6 cameras at max.

◆ The control camera is supporting different Baud rates such as 9600，2400，

4800，19200, and different protocols such as Samsung. VISCA. Pelcd-D.

3

3. TS-0690 Auto Video Tracking Controller

Functions

1) Power—Power indicator.

2) Power switch.

1) Power input, supporting AC 100-240V input.

2) To the ground.

3) VIDEO INPUTS—connecting 6 camera video signal input.

4) VIDEO OUTPUTS—output RCA, BNC, VGA3 camera video signal.

5) CODE—protocol and Baud rate setting switch (not supporting the protocol

from other supplier at present).

6) CAMERA NET— using in high-speed camera RS485.

7) DATA—connecting with the conference controller named TH-0802M.

8) CONFERENCE SYSTEM—connecting with the conference controller

(TS-0604M).

9) CONTROL SYSTEM—connecting with the central controller (PC).

4

4. Technical Specifications

Model

Technical specifications

Auto Video Tracking Controller

Video

Gain 0 dB

Video Bandwidth

150MHz (-3dB),full-loading
0 -10MHz:≤+/- 0.1dB
0 -30MHz:≤+/- 0.5dB

multi-channel to single channel
cross talk

-50dB @ 5 MHz, -45dB @ 10 MHz

Differential phase I/OS

<1.28 degree，3.58MHz

Differential phase error 0.1%, 3.58-4.43MHz

Differential phase gain error 0.1degree, 3.58-4.43MHz

The max transmission delay 5nS(±1nS)

the switching speed 200 ns(longest time)

Signal type composite video signal

video input

interface 6 BNC female interface

minimum/maximum electric
level

analog signal: 0.5V ～ 2.0V p-p

impedance 75 Ω

back wave loss -30dB@5MHz

genlock 0.3V-0.4Vp-p

The largest DC offset error 15mV

Video output

interface

1 BNC female interface and 1 RCA female
interface

minimum/maximum electric
level

Analog signal: 0.5V ～ 2.0V p-p

Impedance 75 Ω

back wave loss -30dB@5MHz

DC offset ±5mV ±5mV at max

conversion type vertical interval

interface 15-pin HD female interface

minimum/maximum electric
level

2.0V p-p

Impedance 75 Ω

back wave loss <-40dB@5MHz

DC offset ±5mV ±5mV at max

sync signal

input/output type

NTSC 3.58，NTSC4.43，PAL，SECAM;

Controlling types

5

Model

Technical specifications

Auto Video Tracking Controller

serial control interface 9-pin female type D RS-232 interface

Baud rate and protocol

Baud rate: 9600, data bit: 8 bits, stop bit: 1,
without parity check bit

specifications

power supply

AC100-240V 50～60Hz(power switching)

temperature

temperature of storage and operating:-20°～
+70°C

Dimension 485(L)x 245(W)x 45mm(H)

Weight About 1.5kg

5. Instruction of using PC software

5.1 Six video channels，Set up the conference platform

1) Open the PC software, set the serial, switching the video through PC software,

the display screen could be switched to different channel displays.

Notice: The address of video channel should be as same as the camera's.

5.2 Screen freeze period function

1) The screen freeze period could be set through PC software from 1-6 seconds.

The screen freeze period is beside the setting period when the camera is

rotating. It also has the function of protecting power losing.

5.3 Image resolution

1) Any of the three image resolutions could be selected by PC software and it

has the function of protecting power losing.

6

5.4 Getting the information of code switching

1) Turning the code switching on the rear panel of the unit, re-up electricity of

the unit, click "achieve" on the PC software to get the code switching protocol of

the camera tracking controller, Baud rate and the type of camera. Checking

whether the protocol, Baud rate and camera type are as same as the real setting

of the camera connection.

If only turning the first code, choosing VISCA protocol.

If only turning the second code, choosing SAMSUNG protocol.

If neither the first or second code is turned, choosing Pelcd D protocol.

If only turning the third code, choosing the Baud rate of the control camera at

2400.

If only turning the fourth code, choosing the Baud rate of the control camera at

4800.

If both the third and fourth codes are turned, choosing the Baud rate of the

control camera at 19200.

If neither the third or the fourth code is turned, choosing the Baud rate of the

control camera at 9600.

If the fifth code is turned, it is desk top camera; if not, it is wall mount camera.

5.5 Reset to Factory Defaults

Click "Reset to Factory Defaults", the screen freeze period of this is 1S, the DPI

is 1024*768, the camera channel number is the first one(it is valid when re-up

electricity).

5.6 Camera address setting

Camera Address ， Input the corresponding camera

address to control the cameras by the following keys.

7

5.7 The invoking, delete and setting of camera presetting

Choosing the camera protocol, input camera address and presetting position to

control the unit.

5.8 Setting the presetting position of the unit

1) Choosing the right protocol, camera address, presetting position, unit

address, adjusting the camera position via the up and down keys to the right

unit, then click "Setting" to finish the presetting bit of the unit. After setting all

the presetting bits accordingly, the camera will automatically point to speech

unit when opening the units.

5.8.1 Supporting three kinds of camera protocol

It could control the rotation direction of the camera and the presetting bits by

selecting the three kinds of different protocols in the PC software.

8

5.8.2. Baud rate testing

You could control the camera well by changing the Baud rate on the PC.

5.8.3 Controlling the cameras with different addresses

You could test several cameras together by changing the physical address of the

camera and then by controlling its moving in PC software.

5.8.4 The effect of system linking

Connecting one conference main controller, several conference discussion units

and the PC, then open the PC software to set the ID number and the presetting

bits of each unit. Then checking whether the working of the discussion units is

normal. Please turn on several discussion units and turn off them to see whether

the camera could point to the presetting bits automatically. Testing samples as

below:

1）When turning on the 1stto 5thdiscussion units continuously, the camera will

point to the 5thunit. Then turning off the 5thunit, the camera will point to the 4

th

unit. Turning off the units continuously and finally when you turn off the 1stunit,

the camera will point to the panoramic position.(Panoramic position is setted by

PC software and before click the confirmation, the camera position should be

adjusted.)

2）Turning on the 1stto 5thdiscussion units, the camera will point to the 5thunit.

Then turning off the 2nd, 3rdand 4thunits, the camera will not moving at this

time. Turning off the 5thunit, the camera will point to the 1stunit then.

3）When tuning on the 1stto 5thunits, the camera will point to the 5thunit. Then

press the priority button on the 6thchairman unit, all the units will be off at this

time and the camera will point to the 6thchairman unit. The same testing

method to TS and TH series.

9

6 Attachment

1) Setting the adjustable ID number, after setting one unit, ID number will add

one automatically to make the presetting bits conveniently.

2) Open the software to read the real data of the machine. You could also read

the output Baud rate, model name selection and the DPI of the camera.

Protocol Explanation:

ID=0 Panoramic Position

Visca Directive explanation: Camera ID=Y. The default video channel is the 1

st

one. Camera ID=1. Presetting bits (1-128). The 128thpresetting bit is using as

panoramic position. Take the example of 8Y 01 04 3F 02 XX FF. In these

numbers, XX should be setted with call presetting bits.

ID number of the unit should be put on before all the protocol. Take the example

of MM NN 8Y 01 04 3F 02 XX FF. In these numbers, MM NN stands for ID number

of the unit.

0.Setting protocol of other functions

Function Remarks Directive

Setting the
video number
of each
channel

Setting the channel numbers:
1,2,3,4,5,6

00 01 FF 10 00 fc 00 01 0D

Selecting the
video channel

Selecting the video channel 1
Selecting the video channel 2
Selecting the video channel 3
Selecting the video channel 4
Selecting the video channel 5
Selecting the video channel 6

00 01 FF 10 00 fb 00 01 0C
00 01 FF 10 00 fb 00 02 0d
00 01 FF 10 00 fb 00 03 0e
00 01 FF 10 00 fb 00 04 0f
00 01 FF 10 00 fb 00 05 10
00 01 FF 10 00 fb 00 06 11

Setting the
screen freeze
period

Setting the screen freeze period:
1S
Setting the screen freeze period:
2S
Setting the screen freeze period:
3S
Setting the screen freeze period:
4S

00 01 FF 10 00 fa 00 01 0B
00 01 FF 10 00 fa 00 02 0c
00 01 FF 10 00 fa 00 03 0d
00 01 FF 10 00 fa 00 04 0e
00 01 FF 10 00 fa 00 05 0f
00 01 FF 10 00 fa 00 06 10

10

Setting the screen freeze period:
5S
Setting the screen freeze period:
6S

Setting the DPI

Setting the DPI: 800*600
Setting the DPI: 1024*768
Setting the DPI: 1024*768

00 01 FF 10 00 fd 00 01 0E
00 01 FF 10 00 fd 00 02 0F
00 01 FF 10 00 fd 00 03 10

The three
kinds of
protocol
setting of the
camera.
Coding above
1,2 bits.

Pelcd_D
VISCA
SAMSUNG
the 7thbit:15
Pelcd_D;16:VISCA;17:SAMSUNG
;18:Pelcd_D。

Restore defaults

00 01 FF 10 00 fE 00 15 23
00 01 FF 10 00 fE 00 16 25
00 01 FF 10 00 fE 00 17 24
00 01 FF 10 00 fE 00 18 26
00 01 FF 10 00 fE 00 20 2e

Setting Baud
rate. Coding
above 3, 4
bits.

Coding switching for two bits.
00:9600;
01:2400;
10:4800;
11:19200。

RX:00 01 FF 10 00 fe 00 00
0E
00 01 FF 10 00 fe 00 01 0f
00 01 FF 10 00 fe 00 02 10
00 01 FF 10 00 fe 00 03 11
00 01 FF 10 00 fe 00 04 12

Using camera.
Coding above
5 bits.

Coding switching is 1 bit. The desk
top type is without coding.
The wall mount type should be
coded.
Pelcd_D is without any coding.
9600 is the desk top camera.

00 01 FF 10 00 fE 00 11 1E
00 01 FF 10 00 fE 00 12 1F

1. In both main conference controllers of TS serials and TH series, if the
desk-top camera is by 0-127 protocol, the presetting bits should be set
from 0 to 127 and the panoramic bit should be set at number 127

ID number of

the camera

ID number

of the unit

Presetting

bits

Function Directive

1 1 1

Presetting bit

00 01 81 01 04 3F 02 01 FF

1 2 2

Presetting bit

00 02 81 01 04 3F 02 02 FF

1 3 3

Presetting bit

00 03 81 01 04 3F 02 03 FF

1 0 7F(127)

Presetting bit

00 00 81 01 04 3F 02 7F FF

1 1 1 Setting

00 01 81 01 04 3F 01 01 FF

1 2 2 Setting

00 02 81 01 04 3F 01 02 FF

1 0 7F(127) Setting

00 00 81 01 04 3F 01 7F FF

11

2. In both main conference controllers of TS serials and TH series, if the
desk-top camera is by Pelcd_D protocol, the presetting bits should be
set from 1 to 128 and the panoramic bit should be set at number 127

D number of

the camera

ID number

of the unit

Presetting

bits

Function Directive

1 1 1

Presetting bit

00 01 FF 01 00 07 00 01 09

1 2 2

Presetting bit

00 02 FF 01 00 07 00 02
0A

1 3 3

Presetting bit

00 03 FF 01 00 07 00 03
0B

1 0 80(128)

Presetting bit

00 00 FF 01 00 07 00 80 88

1 1 1 Setting

00 01 FF 01 00 03 00 01 05

1 2 2 Setting

00 02 FF 01 00 03 00 02 06

1 0 80(128) Setting

00 00 FF 01 00 03 00 80 84

3. In both main conference controllers of TS serials and TH series, if the
ceiling mount camera is by Samsung protocol, the presetting bits should
be set from 0 to 61 and it is adjustable.

D number of

the camera

ID number

of the unit

Presettin

g bits

Function Directive

16 without 1 Presetting bit

00 01 A0 10 10 00 07 00
FF FF FF AF DB (without.
sending twice to get the
menu)

16 1 2 Presetting bit

00 01 A0 10 10 00 07 01
FF FF FF AF DA

16 2 3 Presetting bit

00 02 A0 10 10 00 07 02
FF FF FF AF D9

16 0 3E(62) Presetting bit

00 00 A0 10 10 00 07 3D
FF FF FF AF 9E

16 1 2 Setting

00 01A0 10 10 00 03 01 FF
FF FF AF DE

16 2 3 Setting

00 02 A0 10 10 00 07 02
FF FF FF AF D9

16 0 3E(62) Setting

00 00 A0 10 10 00 03 3D
FF FF FF AF A2

12

4. In both main conference controllers of TS serials and TH series, if the
ceiling mount camera is by Pelcd_D protocol, the presetting bits should
be set from 1 to 61 and it is adjustable.

D number of

the camera

ID number

of the unit

Presetting

bits

Function Directive

16 without 1

Presetting bit

00 01 FF 10 00 07 00 01 18
(without. sending twice to
get the menu)

16 1 2

Presetting bit

00 01 FF 10 00 07 00 02 19

16 2 3

Presetting bit

00 02 FF 10 00 07 00 03
1A

16 0 3E(62)

Presetting bit

00 00 FF 10 00 07 00 3E 55

16 1 2 Setting

00 01 FF 10 00 03 00 02 15

16 2 3 Setting

00 02 FF 10 00 03 00 03 16

16 0 3E(62) Setting

00 00 FF 10 00 03 00 3E 51