itaia ADP 400, ADP 400s, ADP 800 Operating Manual
Operating manual
Automatic-diagnostic lead-acid battery
charger ADP 400(s) / 800
ELECTRONICS
RESEARCH
DEVELOPMENT
Litostrojska cesta 44/d, SI-1000 Ljubljana
T +386 (1) 514 18 00, F +386 (1) 514 18 04
info@itaia.si, www.itaia.si
Table of contents
1. SAFETY INFORMATION AND CAUTION .......................................... 1
1. 1. G
ENERAL
............................................................................................... 1
1. 2. F
IRE-EXTINGUISHING GEAR
.................................................................... 2
1. 3. S
AFETY PRECAUTIONS
............................................................................ 2
2. GUIDELINE FOR CONNECTION AND USE ...................................... 4
2. 1. F
IELD OF USE
.......................................................................................... 4
2. 2. C
ONECTION OF CHARGING
...................................................................... 5
2. 3. I
NDICATIONS AND HANDLING
................................................................. 6
2. 3. 1. Automatic-diagnostic charging ................................................... 7
2. 3. 2. Fast charging ............................................................................... 7
2. 3. 3. Discharge-charge ......................................................................... 7
2. 4. G
UIDELINE FOR SAFE AND PROPER USE OF CHARGER
.............................. 7
3. MAINTENANCE ....................................................................................... 8
3. 1. C
HECKING AND MAINTENANCE
.............................................................. 8
3. 2. S
ERVICING
............................................................................................. 8
3. 3. T
ROUBLESHOOTING
............................................................................... 9
3. 4. S
PARE PARTS
.......................................................................................... 9
4. TECHNICAL DATA ............................................................................... 10
4. 1. E
NVIRONMENTAL CONDITIONS
............................................................. 11
4. 2. T
RANSPORT AND STOCKING
................................................................. 11
4. 3. D
ISPOSAL
............................................................................................. 11
5. CE DECLARATION OF CONFORMITY ........................................... 11
6. WARRANTY OBLIGATIONS .............................................................. 11
Operating manual: ADP 400(s) / 800
1
1. Safety information and caution
1. 1. General
The device, connected and used in accordance with following instructions, is safe to use.
All electrical parts are protected against water, dust and dirt by the relevant IP class.
Housing prevents direct contact with any parts under voltage.
! CAUTION: For any injury resulting from improper use, the user
takes full responsibility.
!
BEFORE MOUNTING AND CONNECTING THE
DEVICE READ MANUAL CAREFULLY!
!
THE CONNECTING OF DEVICE MUST BE CARIED
OUT BY QUALIFIED PERSONNEL!
!
WHEN CONNECTING, DISCONNECT ELECTRICAL
POWER!
!
DO NOT BLOCK ACCESS TO ELECTRICAL PARTS
USED FOR EMERGENCY STOP, CLEANING AND
MAINTENANCE!
!
ALL METAL PARTS OF HOUSING MUST BE
GROUNDED!
!
MAKE SURE THAT WATER DOES NOT GET IN
TOUCH WITH PARTS UNDER VOLTAGE!
Connecting of the device must be done by qualified personnel and in accordance with
local standards. After mounting and connection control measurements must be carried
out to ensure safe and correct operation.
!
Operating manual: ADP 400(s) / 800
2
1. 2. Fire-extinguishing gear
In case of fire use CO2 based fire extinguisher and other equipment following procedures
in accordance with fire-safety regulations.
1. 3. Safety precautions
Safety precautions are meant to provide personal safety and long service life of device.
Any person take part of mounting, connecting or maintenance of the device must follow
this manual and local safety regulations. They have to be qualified for the job and use
appropriate technical equipment.
Before starting:
Disconnect circuit breakers at input and output of the device and make
sure there is no voltage present.
Make sure power is disconnected during the time of mounting and
connecting.
Check the voltage presence with an instrument.
Check grounding connection.
Provide protection against touching the parts under voltage.
Qalified personnel
Transport, mounting, connecting, commissioning and maintenance of the device can
only be preformed by personnel:
with job qualification and experience,
familiar with up to date safety standards and
with knowledge of basic working principles of the device.
Responsibility
We take no responsibility for proper operation and any consequences resulting from use
in discordance with this manual. Safety measures must be provided by user working with
device.
In case of malfunction, please, provide us following information:
type of the device,
serial number,
errors detected,
overall time of operation,
environmental conditions and
application information.
Operating manual: ADP 400(s) / 800
3
Our technical support
Litostrojska cesta 44/d, SI-1000 Ljubljana
T +386 (1) 514 18 00, F +386 (1) 514 18 04
info@itaia.si, www.itaia.si
Declaration of conformity
The device complies with relevant European directives (CE declaration of conformity):
– Electromagnetic compatibility (ULRS, no. 132/2006)
Directive 2004/108/EC and its amendments
– Low voltage Directive (ULRS, no. 27/04)
Directive 2006/95/EC and its amendments
Loading...