ISSI IS62LV256L-25TI, IS62LV256L-25T, IS62LV256L-25JI, IS62LV256L-20TI, IS62LV256L-20T Datasheet
...
®
IS62LV256L
32K x 8 LOW VOLTAGE
CMOS STATIC RAM
FEATURES
• High-speed access time: 15, 20, 25 ns
• Automatic power-down when chip is deselected
• CMOS low power operation
— 255 mW (max.) operating
— 0.18 mW (max.) CMOS standby
• TTL compatible interface levels
• Single 3.3V power supply
• Fully static operation: no clock or refresh
required
• Three-state outputs
ISSI
APRIL 1999
DESCRIPTION
The ISSI IS62LV256L is a very high-speed, low power,
32,768-word by 8-bit static RAM. It is fabricated using ISSI's
high-performance CMOS technology. This highly reliable process coupled with innovative circuit design techniques, yields
access times as fast as 15 ns maximum.
When CE is HIGH (deselected), the device assumes a standby
mode at which the power dissipation is reduced to
50 µW (typical) with CMOS input levels.
Easy memory expansion is provided by using an active LOW
Chip Enable (CE). The active LOW Write Enable (WE) controls
both writing and reading of the memory.
The IS62LV256L is available in the JEDEC standard 28-pin
SOJ and the 450-mil TSOP package.
FUNCTIONAL BLOCK DIAGRAM
A0-A14
VCC
GND
I/O0-I/O7
CE
OE
WE
DECODER
I/O
DATA
CIRCUIT
CONTROL
CIRCUIT
256 X 1024
MEMORY ARRAY
COLUMN I/O
ISSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any errors which
may appear in this publication. © Copyright 1999, Integrated Silicon Solution, Inc.
Integrated Silicon Solution, Inc.
SR033-1A
04/27/99
1
IS62LV256L
®
ISSI
PIN CONFIGURATION
28-Pin SOJ
A7
A6
A5
A4
A3
A2
A1
A0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A14
A12
I/O0
I/O1
I/O2
GND
PIN DESCRIPTIONS
28
27
26
25
24
23
22
21
20
19
18
17
16
15
VCC
WE
A13
A8
A9
A11
OE
A10
CE
I/O7
I/O6
I/O5
I/O4
I/O3
PIN CONFIGURATION
28-Pin TSOP
OE
A11
A9
A8
A13
WE
VCC
A14
A12
A7
A6
A5
A4
A3
TRUTH TABLE
22
23
24
25
26
27
28
1
2
3
4
5
6
7
21
20
19
18
17
16
15
14
13
12
11
10
A10
CE
I/O7
I/O6
I/O5
I/O4
I/O3
GND
I/O2
I/O1
I/O0
A0
9
A1
8
A2
A0-A14 Address Inputs
CE
OE
WE
Chip Enable Input
Output Enable Input
Write Enable Input
I/O0-I/O7 Input/Output
Mode
WEWE
WE
WEWE
Not Selected X H X High-Z ISB1, ISB2
(Power-down)
Output Disabled H L H High-Z ICC1, ICC2
Read H L L DOUT ICC1, ICC2
Write L L X DIN ICC1, ICC2
CECE
CE
CECE
OEOE
OE
OEOE
Vcc Power
GND Ground
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol Parameter Value Unit
VTERM Terminal Voltage with Respect to GND –0.5 to +4.6 V
TBIAS Temperature Under Bias –55 to +125 °C
TSTG Storage Temperature –65 to +150 °C
PT Power Dissipation 0.5 W
IOUT DC Output Current (LOW) 20 mA
Note:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation of the
device at these or any other conditions above those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum rating conditions for extended
periods may affect reliability.
I/O Operation Vcc Current
2
Integrated Silicon Solution, Inc.
SR033-1A
04/27/99
IS62LV256L
ISSI
OPERATING RANGE
Range Ambient Temperature VCC
Commercial 0°C to +70°C 3.3V +10%
Industrial –40°C to +85°C 3.3V ± 10%
DC ELECTRICAL CHARACTERISTICS (Over Operating Range)
Symbol Parameter Test Conditions Min. Max. Unit
VOH Output HIGH Voltage VCC = Min., IOH = –2.0 mA 2.4 — V
VOL Output LOW Voltage VCC = Min., IOL = 4.0 mA — 0.4 V
VIH Input HIGH Voltage 2.2 VCC + 0.3 V
VIL Input LOW Voltage
ILI Input Leakage GND ≤ VIN ≤ VCC Com. –2 2 µA
ILO Output Leakage GND ≤ VOUT ≤ VCC, Outputs Disabled Com. –2 2 µA
(1)
Ind. –5 5
Ind. –5 5
–0.3 0.8 V
®
Notes:
1. VIL = –3.0V for pulse width less than 10 ns.
2. Not more than one output should be shorted at one time. Duration of the short circuit should not exceed 30 seconds.
POWER SUPPLY CHARACTERISTICS
Symbol Parameter Test Conditions Min. Max. Min. Max. Min. Max. Unit
ICC1 Vcc Operating VCC = Max., CE = VIL Com. — 1 — 1 — 1 mA
Supply Current IOUT = 0 mA, f = 0 Ind. — 2 — 2 — 2
ICC2 Vcc Dynamic Operating VCC = Max., CE = VIL Com. — 70 — 60 — 50 mA
Supply Current IOUT = 0 mA, f = fMAX Ind. — 80 — 70 — 60
ISB1 TTL Standby Current VCC = Max., Com. — 3 — 3 — 3 mA
(TTL Inputs) VIN = VIH or VIL Ind. —5 —5 —5
CE
≥ VIH, f = 0
ISB2 CMOS Standby VCC = Max., Com. — 80 — 80 — 80 µA
Current (CMOS Inputs)
Note:
1. At f = f
MAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change.
CAPACITANCE
(1,2)
CE
≤ VCC – 0.2V, Ind. — 100 — 100 — 100
VIN > VCC – 0.2V, or
VIN ≤ 0.2V, f = 0
(1)
(Over Operating Range)
-15 ns -20 ns -25 ns
Symbol Parameter Conditions Max. Unit
CIN Input Capacitance VIN = 0V 6 pF
COUT Output Capacitance VOUT = 0V 5 pF
Notes:
1. Tested initially and after any design or process changes that may affect these parameters.
2. Test conditions: T
A = 25°C, f = 1 MHz, Vcc = 3.3V.
Integrated Silicon Solution, Inc.
SR033-1A
04/27/99
3
Loading...