ISSI IS61LV6432-6TQI, IS61LV6432-6TQ, IS61LV6432-6PQI, IS61LV6432-5TQI, IS61LV6432-133TQ Datasheet

IS61LV6432

Integrated Silicon Solution, Inc.

1

PRELIMINARY SR018-1C
06/01/98

ISSI

®

This document contains PRELIMINARY data. ISSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product.
We assume no responsibility for any errors which may appear in this publication. © Copyright 1997, Integrated Silicon Solution, Inc.

FEATURES

• Internal self-timed write cycle

• Individual Byte Write Control and Global Write

• Clock controlled, registered address, data and
control

• Pentium™ or linear burst sequence control
using MODE input

• Three chip enables for simple depth expansion
and address pipelining

• Common data inputs and data outputs

• Power-down control by ZZ input

• JEDEC 100-Pin TQFP and PQFP package

• 3.3V V

CC and 2.5V VCCQ for 2.5 I/O's

• Two Clock enables and one Clock disable to
eliminate multiple bank bus contention.

• Control pins mode upon power-up:
– MODE in interleave burst mode
– ZZ in normal operation mode
These control pins can be connected to GND

Q

or VCCQ to alter their power-up state

• Industrial temperature available

DESCRIPTION

The ISSI IS61LV6432 is a high-speed, low-power synchro­nous static RAM designed to provide a burstable, high­performance, secondary cache for the Pentium™, 680X0™,
and PowerPC™ microprocessors. It is organized as 65,536
words by 32 bits, fabricated with ISSI's advanced CMOS
technology. The device integrates a 2-bit burst counter, high­speed SRAM core, and high-drive capability outputs into a
single monolithic circuit. All synchronous inputs pass through
registers controlled by a positive-edge-triggered single clock
input.

Write cycles are internally self-timed and are initiated by the
rising edge of the clock input. Write cycles can be from one to
four bytes wide as controlled by the write control inputs.

Separate byte enables allow individual bytes to be written.

BW1

controls DQ1-DQ8,

BW2

controls DQ9-DQ16,

BW3

controls DQ17-DQ24,

BW4

controls DQ25-DQ32, conditioned

by

BWE

being LOW. A LOW on GW input would cause all bytes

to be written.
Bursts can be initiated with either

ADSP

(Address Status

Processor) or

ADSC

(Address Status Cache Controller) input
pins. Subsequent burst addresses can be generated inter­nally by the IS61LV6432 and controlled by the

ADV

(burst

address advance) input pin.
Asynchronous signals include output enable (OE), sleep mode

input (ZZ), clock (CLK) and burst mode input (MODE). A HIGH
input on the ZZ pin puts the SRAM in the power-down state.
When ZZ is pulled LOW (or no connect), the SRAM normally
operates after three cycles of the wake-up period. A LOW
input, i.e., GNDQ, on MODE pin selects LINEAR Burst. A VCCQ
(or no connect) on MODE pin selects INTERLEAVED Burst.

IS61LV6432

64K x 32 SYNCHRONOUS
PIPELINE STATIC RAM

MAY 1998

FAST ACCESS TIME

Symbol Parameter -166 -133 -117 -5 -6 -7 -8 Unit

tKQ CLK Access Time 5 5 55678 ns
tKC Cycle Time 6 7.5 8.5 10 12 13 15 ns
— Frequency 166 133 117 100 83 75 66 MHz

ISSI

®

IS61LV6432

2

Integrated Silicon Solution, Inc.

PRELIMINARY SR018-1C

06/01/98

ISSI

®

BLOCK DIAGRAM

16

BINARY

COUNTER

A15-A0

BW1

GW

CLR

CE

CLK

Q0

Q1

MODE

A0'

A0

A1

A1'

CLK

ADV

ADSC
ADSP

14 16

ADDRESS

REGISTER

CE

D

CLK

Q

DQ32-DQ25

BYTE WRITE

REGISTERS

D

CLK

Q

DQ24-DQ17

BYTE WRITE

REGISTERS

D

CLK

Q

DQ16-DQ9

BYTE WRITE

REGISTERS

D

CLK

Q

DQ8-DQ1

BYTE WRITE

REGISTERS

D

CLK

Q

ENABLE

REGISTER

CE

D

CLK

Q

ENABLE

DELAY

REGISTER

D

CLK

Q

BWE

BW4

CE1

CE3

CE2

BW2

BW3

64K x 32

MEMORY

ARRAY

32

INPUT

REGISTERS

CLK

OUTPUT

REGISTERS

CLK

32

OE

4

32

OE

DATA[32:1]

IS61LV6432

Integrated Silicon Solution, Inc.

3

PRELIMINARY SR018-1C
06/01/98

ISSI

®

PIN CONFIGURATION

100-Pin TQFP and PQFP (Top View)

NC
DQ16
DQ15
VCCQ
GNDQ
DQ14
DQ13
DQ12
DQ11
GNDQ
VCCQ
DQ10
DQ9
GND
NC
VCC
ZZ
DQ8
DQ7
VCCQ
GNDQ
DQ6
DQ5
DQ4
DQ3
GNDQ
VCCQ
DQ2
DQ1
NC

A6

A7

CE1

CE2

BW4

BW3

BW2

BW1

CE3

VCC

GND

CLK

GW

BWEOEADSC

ADSP

ADV

A8

A9

NC
DQ17
DQ18

VCCQ

GNDQ

DQ19
DQ20
DQ21
DQ22

GNDQ

VCCQ

DQ23
DQ24

VCCQ

VCC

NC

GND
DQ25
DQ26

VCCQ

GNDQ

DQ27
DQ28
DQ29
DQ30

GNDQ

VCCQ

DQ31
DQ32

NC

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30

80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51

100

99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81

31 32 33 34 35 36 37 38 39 40 41 42 43 44 45

MODE

A5A4A3A2A1

A0

NC

NC

GND

VCC

NC

NC

A10

A11

A12

A13

A14

A15

NC

46 47 48 49 50

PIN DESCRIPTIONS

A0-A15 Address Inputs
CLK Clock

ADSP

Processor Address Status

ADSC

Controller Address Status

ADV

Burst Address Advance

BW1-BW4

Synchronous Byte Write Enable

BWE

Byte Write Enable

GW

Global Write Enable

CE1

, CE2,

CE3

Synchronous Chip Enable

OE

Output Enable

DQ1-DQ32 Data Input/Output
ZZ Sleep Mode
MODE Burst Sequence Mode
VCC +3.3V Power Supply
GND Ground
VCCQ Isolated Output Buffer Supply:

+3.3V
GNDQ Isolated Output Buffer Ground
NC No Connect

IS61LV6432

4

Integrated Silicon Solution, Inc.

PRELIMINARY SR018-1C

06/01/98

ISSI

®

TRUTH TABLE

Address

Operation Used

CE1CE1

CE1CE1

CE1

CE2

CE3CE3

CE3CE3

CE3

ADSPADSP

ADSPADSP

ADSP

ADSCADSC

ADSCADSC

ADSC

ADVADV

ADVADV

ADV

WRITEWRITE

WRITEWRITE

WRITE

OEOE

OEOE

OE

DQ

Deselected, Power-down None H X X X L X X X High-Z

Deselected, Power-down None L L X L XXXXHigh-Z

Deselected, Power-down None L X H L XXXXHigh-Z

Deselected, Power-down None L L X H L X X X High-Z

Deselected, Power-down None L X H H L X X X High-Z

Read Cycle, Begin Burst External L H L L X X X L Q
Read Cycle, Begin Burst External L H L L X X X H High-Z
Write Cycle, Begin Burst External L H L H L X L X D
Read Cycle, Begin Burst External L H L H L X H L Q
Read Cycle, Begin Burst External L H L H L X H H High-Z
Read Cycle, Continue Burst Next X X X H H L H L Q
Read Cycle, Continue Burst Next X X X H H L H H High-Z
Read Cycle, Continue Burst Next H X X X H L H L Q
Read Cycle, Continue Burst Next H X X X H L H H High-Z
Write Cycle, Continue Burst Next X X X H H L L X D
Write Cycle, Continue Burst Next H X X X H L L X D
Read Cycle, Suspend Burst Current X X X HHHHLQ
Read Cycle, Suspend Burst Current X X X HHHHHHigh-Z
Read Cycle, Suspend Burst Current H X X X H H H L Q
Read Cycle, Suspend Burst Current H X X X HHHHHigh-Z
Write Cycle, Suspend Burst Current X X X H H H L X D
Write Cycle, Suspend Burst Current H X X X H H L X D

Notes:

1. All inputs except OE must meet setup and hold times for the Low-to-High transition of clock (CLK).

2. Wait states are inserted by suspending burst.

3. X means don't care.

WRITE

=L means any one or more byte write enable signals (BW1-BW4) and

BWE

are LOW or GW is LOW.

WRITE

=H means all byte write enable signals are HIGH.

4. For a Write operation following a Read operation, OE must be HIGH before the input data required setup time and held HIGH
throughout the input data hold time.

5.

ADSP

LOW always initiates an internal READ at the Low-to-High edge of clock. A WRITE is performed by setting one or more

byte write enable signals and

BWE

LOW or GW LOW for the subsequent L-H edge of clock.

PARTIAL TRUTH TABLE

Function

GWGW

GWGW

GW

BWEBWE

BWEBWE

BWE

BW1BW1

BW1BW1

BW1

BW2BW2

BW2BW2

BW2

BW3BW3

BW3BW3

BW3

BW4BW4

BW4BW4

BW4

READ H H X X X X
READ H X H H H H
WRITE Byte 1 H L L H H H
WRITE All Bytes X LLLLL
WRITE All Bytes L XXXXX

IS61LV6432

Integrated Silicon Solution, Inc.

5

PRELIMINARY SR018-1C
06/01/98

ISSI

®

INTERLEAVED BURST ADDRESS TABLE (MODE = VCCQ or No Connect)

External Address 1st Burst Address 2nd Burst Address 3rd Burst Address

A1 A0 A1 A0 A1 A0 A1 A0

00 01 10 11
01 00 11 10
10 11 00 01
11 10 01 00

LINEAR BURST ADDRESS TABLE (MODE = GNDQ)

0,0

1,0

0,1A1', A0' = 1,1

ABSOLUTE MAXIMUM RATINGS

(1)

Symbol Parameter Value Unit

TBIAS Temperature Under Bias –10 to +85 °C
TSTG Storage Temperature –55 to +150 °C
PD Power Dissipation 1.8 W
IOUT Output Current (per I/O) 100 mA
VIN, VOUT Voltage Relative to GND for I/O Pins –0.5 to VCCQ + 0.3 V
VIN Voltage Relative to GND for –0.5 to 4.6 V

for Address and Control Inputs

Notes:

1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation of the
device at these or any other conditions above those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum rating conditions for extended
periods may affect reliability.

2. This device contains circuity to protect the inputs against damage due to high static voltages
or electric fields; however, precautions may be taken to avoid application of any voltage higher
than maximum rated voltages to this high-impedance circuit.

3. This device contains circuitry that will ensure the output devices are in High-Z at power up.