INTRODUCTION
Congratulations on your purchase of the Vector 212 Extension Guitar cabinet. You are now
the owner of the most innovative guitar speaker combo cabinet ever produced. The same
innovation and killer sound that you can find in our Vector Cabinet and Theta Head is now
combined into one package and is ready for low-end players and shredders of all kinds.
Years of experience in designing the highest performance Active Sound Reinforcement
cabinets has allowed ISP Technologies engineers to develop the ultimate guitar combo
extension cabinet. The Vector 212 was designed to provide the maximum possible over the
top performance with stunning low-end punch and definition. With 100 watts RMS
driving a single Celestion 12” speaker and 300 watts available to deliver the
thunderous low end, the Vector 212 really delivers the sound never before
available in a combo package.
Please read this manual carefully for a through explanation of the Vector 212 and its
functions.
PRECAUTIONS
NOTE: IT IS VERY IMPORTANT THAT YOU READ THIS SECTION TO PROVIDE YEARS OF
TROUBLE FREE USE. THIS UNIT REQUIRES CAREFUL HANDELING.
All warnings on this equipment and in the operation instructions should be adhered to and all
operating instructions should be followed.
Do not use this equipment near water. Care should be taken so that objects do not fall onto and
liquids are not spilled into the unit through any openings.
The power cord should be unplugged from the outlet when the unit is left unused for a long
period of time.
DO NOT ATTEMPT TO SERVICE THIS EQUIPMENT. THIS EQUIPMENT SHOULD BE SERVICED BY
QUALIFIED SERVICE PERSONNELL ONLY. DO NOT MAKE ANY INTERNAL ADJUSTMENTS OR
ADDITIONS TO THIS EQUIPMENT AT ANY TIME. DO NOT TAMPER WITH INTERNAL
ELECTRONIC COMPONENTS AT ANY TIME. FAILURE TO FOLLOW THESE INSTRUCTIONS WILL
VOID THE WARRANTY OF THIS EQUIPMENT, AND MAY CAUSE A SHOCK HAZZARD.
POWER REQUIREMENTS
This unit requires connection to a 120-volt AC outlet. Do not cut or disconnect the ground pin
on the power cord. Do not attempt to connect this unit to any power source other than the
specified 120VAC. The Theta Combo will typically draw approximately three amps of current
when driving a 4-ohm load.
Rear Panel Description
1. VOLUME LEVEL
Select the level of volume output by starting with the knob turned all the way
counter-clockwise and turning it clockwise until desired volume is met.
2. XLR INPUT JACK
This female connector provides an input for balanced line level signal source. Hook
up ¼” phone jack from the output of the Theta Combo into the XLR input of the
Vector 212. (See connection diagram)
3. XLR OUTPUT JACK
This male connector provides a balanced loop through for connecting to additional
powered cabinets.
4. POWER SWITCH
Lets the user control the power of the amp by selecting if the speaker is off or on.
5. NEUTRIK POWERCON CONNECTOR INPUT
This module provides a connection for the power cord.
6. FUSE REPLACEMENT
Twisting knob counter-clockwise can access the fuse.
Connection Diagram
Power:
Speakers:
Response:
Dimensions:
Weight:
400 watt RMS
12” Celestion (100 watts), 12” large
excursion neo woofer (300 watts)
45Hz at (-10dB)
29.9” W x 19.9” H x 14.1” D
65 lbs.
Vector 212 SPECIFICATIONS
WARRANTY AND SERVICE
The Internal Circuitry is fully guaranteed to be free of defects under normal use and service
for a period of three years from the date of purchase. The Speakers and Cabinet that are
used in this product are fully guaranteed to be free of defects under normal use and service
for a period of three years.
Any damage resulting from the misuse or the failure to follow the precautions and
instructions will void the warranty.
In the event that the unit needs to be repaired, please return the unit to ISP Technologies
directly. Simply repack the unit, send a copy of the original receipt, a note stating the
problem, and send it to:
ISP Technologies, Inc
5479 Perry Drive Unit B
Waterford, MI 48329
Attn: Repair Dept.
All shipping charges must be fully prepaid.
ISP will not be responsible for any damages incurred in shipping of any unit. Any claim will
need to be settled with the shipping company.
The warranty will be voided if the serial number has been tampered with in any way.
The warranty card must also be filled out and returned in order to activate the warranty.
Should you have any questions for the repair department prior to returning the product
please call 1-(248)-673-7790
NOTE: This Product may be covered under one or more of the following patents or patents
pending: 7,035,413; 6,944,305; 6,931,134; 6,831,514; 6,091,013
ISP TECHNOLOGIES, LLC
5479 PERRY DRIVE UNIT B
WATERFORD, MI. 48329
248-673-7790
FAX: 248-673-7696
www.isptechnologies.com
Loading...