Isound DREAM TIME User Manual

dreamTIME
Package Contents:
• Main Speaker Unit
• Wireless Remote Control
• 3.5mm Audio Cable
• AC Adapter
• iPod
® Spacer Brackets
Controls and Indicators
STAND BY/SOUR CE
SNOOZ E
Mult i-fun ction D isp lay
AL ARM SE LECT
AL ARM 2
AL ARM 1
SLE EP
NAP
CLOC K
TUNE/TRACK DOWN
TUNE/TRACK UP
FM An tenn a
Wir e
Bac kup Ba ttery C ompar tmen t
Li ne In
Jac k
Spea ker Po rt
Rem ovabl e Fitt ing B racke t
iPo d Pin Co nnec tor
VOL UME DOWN
DC IN 12V
Jac k
PLAY /PAUSE
VOL UME UP
Rem ote Sen sor
Win dow
Multi-Function Display (Backlight)
BA ND i co n
In dic ato r
A la rm 2
A la rm 1
In dic ato r
We ek day In dic ato r
iP od i co n NA P ico n
SN OOZ E i co n
Ti me/A lar m/R adi o Fr equ en cy In dic ato r
SL E EP i con
Install iPod Removable Fitting Bracket
The dreamTIME includes several different iPod brackets. Always use the proper bracket to insure your iPod is firmly seated on the dreamTIME dock.
Sel ect the right fitting bracket for your iP od (se e chart below) .
Video 30gig
Bracke t
iPod Video 30GB
20 & 30gig
Bracke t
iPod 3Gen 10GB iPod 3Gen 15GB
20GB
iPod 3Gen iPod 4Gen
20GB
iPod Photo 30GB
Video 60gig
Brack et
iPod Video 60GB
Color
40 & 60gig
Brack et
iPod 3Gen 30GB iPod 3Gen 40GB iPod 4Gen 40GB
40GB
iPod Photo iPod Photo
60GB
mini
Brack et
All iPod mini
nano
Brack et
iPod nano 1GB iPod nano 2GB iPod nano 4GB
Remote Control Unit
The remote is compatible will all dockable iPod’s. A iPod must be connected the dreamTIME’s dock to function properlay.
SNO OZE
VO LU MEDOWN
PL AY/PA USE
TU NE/TR ACK DOWN
MUT E
STA NDB Y/SOU RCE
VO LU ME UP
SL EE P
TU NE/TR ACK S UP
EQ
www.isound.net
Page 1
Page 2
Install/Replace Battery on the Remote Control
The remote’s battery is factory installed. Open the battery compartment door and remove the protective battery sheet before use.
When the remote’s battery becomes weak, replace the battery with a (TYPE CR2032 3V Lithium Battery). When installing the new battery make sure to install the battery with the + side up.
Install/Replace Back-up Battery of the dreamTIME
This unit uses a back-up system to provide conitinous clock operation in the event of a power failure. If the Back-up Battery has been installed and a power failure occurs or the AC cord is accidentlly disconnected, the current time and alarm settings will be temporarily maintained. Otherwise, you must reset the time and alarm settings.
Installing Back-Up Batteries
1. Make sure the AC adapter is connected or you may lose all of your current settings.
2. Open the battery compartment on the bottom of the unit.
3. Insert 2 “AA” batteries, check that the polarity(+& - ends of the batteries) match the engraving inside the battery compartment.
4. Close the battery door.
5. DO NOT mix old and new batteries.
AC Power Supply Connection
1. Insert 2 “AA” batteries, check that the polarity(+ & - ends of the batteries) match the engraving inside the battery compartment
Functions
Power Unit On/Off
1. Press and hold STANDBY/SOURCE for about 2 seconds, the unit will power up to the last played audio source.
2. To power “OFF” the dreamTIME \, hold STANDBY/SOURCE for about 2 seconds.
AC Power Supply Connection
1. Insert 2 “AA” batteries, check that the polarity (+ & - ends of the batteries) match the engraving inside the battery compartment
Selecting Audio Source
1. With the dreamTIME powered on, press the STANDBY/SOURCE button to toggle the different sources.
Adjusting the Volume
1. Press the volume up or volume down buttons. The LCD will the volume level.
Mute Volume
1. On the wireless remote, press MUTE to silent the dreamTIME, press MUTE again to resume the volume.
Equalizer
1. On the wireless remote, press EQ to toggle between the different equalizer modes.
Setting Clock
1. Power “ON” the dreamTIME speaker.
2. Press and hold CLOCK for about 2 seconds, the LCD backlight illuminates and the HOUR and MINUTES digits start to flash.
3. Press TUNE/TRACK up or down to set the HOUR, press VOLUME up or DOWN to set the minutes.
4. Press CLOCK to confirm the HOUR/MINUTES, the digits will stop
.
flashing.
5. The WEEKDAY icon will be flashing.
6. Press TUNE/TRACK up or down to set the day of the week.
Setting Alarm 1
1. Power the dreamTIME speaker “OFF” .
2. Press and hold the ALARM 1 button for two seconds. The ALARM 1 icon flashes and the HOUR and MINUTE digits start to flash.
3. Press TUNE/TRACK button up or down to set the HOUR, press the VOLUME button up or down to set the minutes.
4. The WEEKDAY icon will be flashing.
5. Press the TUNE/TRACK button up or down to adjust the day of the week.
.
6. Press the VOLUME button up or down to choose the wake-up source.
7. Press the ALARM 1 button to confirm the ALARM time and wake-up SOURCE.
Setting Alarm 2
1. Power the dreamTIME speaker “OFF” .
2. Press and hold the ALARM 2 button for two seconds. The ALARM 2 icon flashes and the HOUR and MINUTE digits start to flash.
3. Follow the same procedures as setting ALARM 1.
Display Alarm Settings
1. Power the dreamTIME speaker “OFF” .
2. Quick press the ALARM 1 or ALARM 2 buttons.
Line In Feature
The dreamTIME speaker features a line in. The line in is used to connect any audio device that uses a standard headphone input.
For Technical Support Please Contact: 1-877-999-DREAM Or visit us on the web @ www.i.sound.net
Page 3
Page 4
PO Box 478 Torrance, CA 90508
Page 5
Loading...