User manual
THERMO-Insect-Bite-Healer
Art.-Nr. 73190
Dear Customer,
Congratulations on the purchase of this quality product. Please read the user manual
carefully before initial operation. Retain this manual for future reference.
1. Product description
The THERMO-Insect-Bite-Healer is suitable for external application in case of insect bites
from midges, mosquitoes, and horseflies (biting houseflies). When applied immediately
after a sting THERMO-Insect-Bite-Healer eliminates or reduces the itching and
subsequent swelling of the affected area. At the same time it reduces the danger of pain
and redness. An appearance of an inflammation can already be prevented in the
development phase.
2. Application
1. Place the heating surface of the THERMO-Insect-Bite-Healer exactly on the bite area
while gently pressing on the button on the opposite end of the device. Maintain the unit
slightly pressed on during the period of treatment.
2. The yellow LED lights up to indicate that the THERMO-Insect-Bite-Healer is heating
up.
3. The LED turns green when the correct application temperature has been reached.
4. Release the button. The first application is complete. Let the area cool down.
5. Repeat the procedure as required until the symptoms (pain or itching) have subsided.
3. Side effects
No side effects are known to occur when applying this device correctly. When applied on
healthy skin, there is no risk of skin damage such as burns, necrosis, or any systemic
effects. Children might experience an unpleasant feeling of heat.
4. Important notes
- Not recommended for treatment of children under three years of age!
- Do not apply on mucous membranes, eyes or lips!
- Do not apply on open wounds or damaged skin!
- The device does not replace a prophylactic treatment of Malaria when travelling abroad!
- The THERMO-Insect-Bite-Healer is designed to alleviate itching and is ineffective for
treating known or acute allergies against insect bites!
- Children should not use the THERMO-Insect-Bite-Healer without adult supervision.
5. Cleaning instructions
- Do not use aggressive cleaning products
- Clean the contacts with a dry cloth.
6. Inserting and replacing the batteries
• Open the battery compartment on the bottom side of the THERMO-Insect-Bite-Healer
with a sharp object and insert two AAA-type alkaline batteries (not included) in it. To
replace the batteries remove the old ones first. Please observe the information under
point 8 when inserting, replacing and disposing of the batteries!
• Insert the batteries into the battery compartment orienting them as indicated.
• Close the battery compartment.
7. Technical data
Power supply:
2 x 1.5 V batteries (Size AAA), alkaline type
(not included)
Function display:
LED
Dimensions:
approx. 11.5 x 2.5 x
2 cm
Weight:
approx. 40 g
0483
8. Attention: Important notes about batteries
• Use only alkaline batteries with this device!
• Never use new and old batteries together.
• Remove the batteries if the device is not being used for longer time periods. Battery
leakage can result in permanent damage to the device.
• Information on disposal of batteries:
Batteries contain pollutants and their disposal is subject to legal
regulations. The used batteries must therefore be returned to the
point of purchase or taken to a collection point from the relevant
public waste disposal body. Under no circumstances should the
batteries be placed within the domestic waste, yellow waste bag, or
similar. Only empty batteries should be taken to the collection
points and adequate measures should be taken to avoid short
circuits (e.g. taping of poles).
9. Safety instructions
Important: This guarantee does not cover damage resulting from non-observance of
these instructions. ISOTRONIC does not accept liability for any consequential damages.
- Operate only by applying the correct voltage.
- Always use original spare parts in case of repairs to avoid serious damage.
- Check any supply lines or live lines connected to the device for damage or faulty
electrical isolation. The device should not be operated if any faults or obvious damage
is detected.
- Any repairs or other work such as replacing a fuse, etc. should only be performed by an
authorised electrician.
- It should be noted that operational errors or connection faults fall outside of
ISOTRONIC’s area of influence and that no liability will be accepted for any
consequential damages.
- Before operating the device it is necessary to check if it is suitable for the respective ^
location.
10. Symbols used
Attention: Read the instruction manual before use!
BF class medical device (earth-free) according to IEC 60601-1
11. General information
1. Keep electric devices, packaging material, etc. away from children.
2. Dispose of any packaging and waste material (sheets, old products) in an
environmentally responsible manner.
3. Passing on of this product should always take place in conjunction with the
corresponding instruction manual.
4. The design and technical data of this device are subject to modifications as part of
continuous product improvement.
12. Guarantee
This product comes with a 2 year guarantee. The guarantee covers the
correction of any defects related to imperfect material or manufacturing faults. The
guarantee does not cover expendable parts such as lamps, rechargeable batteries or
batteries.
ISOTRONIC has no influence on the correct and proper mounting and operation of the
product and can therefore only warrant the completeness and faultless condition of the
product before use.
We do not offer warranty nor accept liability for any damages or consequential damages in
relation to this product. This applies especially when any changes or repairs have been
performed on the product, or any connections have been modified, or any other parts have
been used, or, if any damages have occurred as a result of incorrect operation, negligent
treatment or misuse of the product.
Your
ISOTRONIC-Team
D- 72160 Horb
Version: 06/05
Information on environmental protection
This product should not be disposed of through the normal domestic waste after
reaching its useful life, but it should, instead, be taken to a collection point for
recycling electrical and electronic equipment. This is indicated by the symbol on the
product, in the user manual or on the packaging.
The materials are recyclable according to their markings. Mit der
By recycling and reusing used equipment and the materials contained therein you are
making an important contribution to the protection of our environment.
The local administration will provide you more information about your nearest recycling
and waste disposal point.
Loading...